Search Documents

By Xue Yongpeng, Zhu Zhenhai, Zhu Ming

The purpose of the Solid Medium Controlled Blasting Technique and Its Applications is to have the inside of the vessel-shaped framework (e.g: oil tank , water pool, gas chamber, chimney, water tower, grain warehouse and etc.) or the one side of the thin wall-shaped structure(e.g: steel bar concrete wall and etc.), both of which are intended to be demolished, inserted with the required solid medium (e.g: soil , sand , coal, salt and etc.) ,in which there is a certain mass density, and then through which the blasting energy is transferred to fulfill the blasting task. For such a technique, it is necessary to bury the explosives into the inserted solid medium and then to start the explosion to blast the intended target into pieces. The filling of the solid medium may be done mechanically or by man. Compared with the water pressure blasting technique, this one has the characteristics of good effect. wide application, simplified construction procedure , safe and reliable operation and small vibration (less vibration than water pressure blasting by 80% to 90%)in particular without any flying stones, thus resulting in better and comprehensive social and economickfficiency.

Jan 1, 2000

By C. M. Frost

Crude shale oil prepared by gas-combustion retorting of Colorado oil shale was hydrogenated over a cobalt molybdate catalyst at an operating pressure of 1,000 psig, temperatures of 781° and 761° F, and liquid hourly space velocities of 0.10 and 0.05 Vo/Vo/hr, respectively. The yields of total liquid products and the amounts of nitrogen and sulfur removed were comparable with those obtained at an operating pressure of 3,000 psig and a liquid hourly space velocity of 1.0 Vo/Vo/hr. Approximately 1.5 times as much gasoline was produced at the lower pressure and space velocities.

Jan 1, 1973

By A. Navarra

Peirce-Smith converting (PSC) is applied for roughly 50% of primary nickel and 70% of primary copper production. PSC cycles produce batches of ironfree sulfide matte (or blister copper, in the case of copper smelters), that are subject to further processing. However, the number of cycles that can be performed simultaneously is limited by the offgas handling system. Moreover, PSC suffers from variation in the yield and duration of the cycles. This variation is managed by conventional smelter designs, in which the upstream smelting capacity exceeds the nominal converting capacity; PSC is thus a major bottleneck in conventional nickel and copper smelters. Stabilization and standardization of PSC operations can therefore increase smelter throughput. The current paper presents a discrete event simulation (DES) framework to assist in smelter debottlenecking. It features random number generation to represent cycle variability, and time-adaptive finite differences to represent thermochemical complexity. Preliminary computations are presented.

By R. Esteban, D. Runnels, J. Torrealba-Vargas, G. Couture

"Data handling is an important step in the development of a simulator of a mineral processing circuit. The model requires representative data of the scenario to be modeled. The model development involves protocols that must be followed very closely to complete a successful project.Data handling of large and diverse datasets (metallurgical test results, geological data, mining models, historical data, etc.) is a key element of the model. The information needs to be processed, reconciled, interpreted, modeled and presented to support the design or the optimization of a mineral processing plant.Best practice recommends that teams from different disciplines (such as mining, metallurgy, geology and environmental) interact to define the most important variables that could influence the simulator. For example by adopting a geometallurgical approach in the earlier stages of the project, it is possible to consolidate the number of main ore rock types in a testwork program (saving money and time) by involving geologists and metallurgists in the sample selection and data interpretation.Planning the development of a model involves an understanding of the software capabilities but also the limitations and the magnitude of the data required to calibrate the model in case of changes in the project.A successful model requires a deep understanding of the circuit to be modeled and thus plant personnel should be considered as members of the team.This paper describes the use of the "state of the art" tools for data analysis, simulation and optimization; and shows three practical examples of the use those tools in the design of mineral processing plants."

Jan 1, 2015

By H. R. Babitzke

The purpose of this Bureau of Mine- investigation was to develop columbium and tantalum alloys suitable or u at elevated temperatures. Columbium and tantalum were combined with tungsten, hafnium, zirconium, molybdenum, vanadium, and titanium, and the resulting alloys were evaluated with respect to workability, hardness, electrical resistivity, strength at elevated temperatures, oxidation resistance, and weldability. Cb-33Hf-10W-10Ti, Cb-20111-5Mo, and Cb-30Hf-5Mo exhibited superior high temperature properties. Cb-33Hf-10W-10Ti had tensile strength values of 44,300 psi at 1,200° C and 16,500 psi at 1,400° C, Cb-20Hf-5Mo had values of 35,700 and 20,700 psi, respectively. The corresponding values for Cb-30Hf-5Mo were 38,900 and 17,800 psi. These alloys are fabricable by conventional methods with excellent strength at temperatures up to and including 1,400° C. An oxidation rate of 7 to 21 mg/cm2/hr was observed up to 1,000° C.

Jan 1, 1967

By A. G. Paithankar, G. B. Misra

Although certain physical mechanical properties of rocks have been claimed to give an estimate of penetration rate in percussive drilling, the authors' work shows that the correlation of penetration rate with individual rock properties is Poor. The authors have developed a good correlation between penetration rate and a set of rock properties but the relation is complex. Energy per unit volume has been used as a measure of penetration rate in percussive drilling by Hustrulid and Fairhurst; however, their test setup is large wing a full size drill bit. The authors determined the minimum energy for unit volume Ev min for any rock at the optimum index angle in a simple laboratory drop tester wing a sharp microbit with a tip angle of ll0°. This Ev min has been found to correlate well with penetration rate obtained in controlled laboratory drilling in different rocks for different stages of bit wear. A comprehensive relation has been developed between penetration rate and Ev min.

Jan 1, 1981

By Greenhalgh L. P H

The opportunities offered by an increasingly volatile world invite the international consultant or engineering services contractor to broaden attitudes, diversify interests, expand capabilities, retain and develop specialist skills and base judgements upon sound principles and solid experience. The wide-ranging scope of this review reflects such a change but the topics of discussion are not intended to be exhaustive or to detract from many other current developments.The subject of environmental protection, effluent control and pollution prevention is a primary consideration in the application of many mineral processing technologies but is not covered here. There is an array of developments relating to noxious gas emissions and toxic wastes and the paramount importance of this matter justifies comprehensive conferences dedicated solely to the application of suitable measures. This review concentrates therefore on the main stream processing techniques for the primary recovery of values.

Jan 1, 1993

By R. J. Sweigard

Many states are considering the need to establish or modify policy relating to the disposal of coal ash. One of the primary concerns is the impact of leachate from the ash disposal sites upon groundwater and nearby bodies of surface water. A detailed site investigation was conducted at a coal ash disposal facility associated with a power generation station. The disposal site is situated alongside a major river. Monitoring wells were installed and soil samples were taken for characterization. Groundwater models were used to simulate migration of leachate from the disposal site toward the river. Such models could be used potentially to verify regulatory compliance. This paper addresses the validation and adaptability of these models to this case and their usefulness as possible tools to be used in future environmental audits.

Jan 1, 1992

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (CFR) Com¬mittee of the Coordinating Research Council (CFC) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36. 4/ Further re¬ports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941.4/ No reports were made on motor gasolines sold during the winter of l941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed. The present report presents analytical data for 3,011 samples, representing the products of 113 companies. Most of the samples represented in this report were obtained during July and August 1946. As in previous surveys the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gasoline are not considered adequate to represent this type of motor fuel, data for the analyses have not been averaged, but the individual items are tabulated. The number of samples, items, and brands comprising each group is as follows: Regular-price, 1,585 samples, 311 items, and 99 -brands; premium-price, 1,422 samples, 280 items, and 94 brands; third-grade, 4 samples, 4 items, and 4 brands. The meaning of these terms as used in the survey is as follows:"

Dec 1, 1946

By John I. Kasteler, John H. Hild

"INTRODUCTION The South Hecla mine, one of the principal mines of the Alta United Mines Co., is situated at Alta in thee Little Cottonwood mining district, about 30 miles southeasterly from Salt Lake City, Utah. The mine has produced copper, lead, zinc, gold, and silver, and is reported to have been one 'of the principal sources of this country's bismuth from 1912 to 1925. The tungsten mineral, scheelite, has been found but has not been recovered. The extreme need for these minerals during World War II prompted an examination of the property by the Bureau of Mines and resulted in an unpublished report entitled ""The South Hecla Mine, Salt Lake County, Utah"" (fig. 1).A Bureau of Mines project 3301 was initiated, and operations were started early in 1943. The primary purpose of the project was to increase substantially the reserves of bismuth and tungsten ores. The critical situation in regard to lead, copper, and zinc developed during the early stages of the operation, and the work was expanded to include the development of ores 'of these metals.An investigation of 'the Albion, Rustler, and Greeley workings adjoining the South Hecla mine was made, and this work is also described (fig. 2); ACKNOWLEDGEMENTSIn Its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each investigative project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests."

Jan 1, 1948

By David J. Akers

INTRODUCTION The variety of uses of coal and the wide range of characteristics of coal combine to produce a need for a wide variety of laboratory analysis. Coal is used to heat homes, produce electricity, and make coke for steel manufacture. It can also be used to produce both gaseous and liquid fuels as well as a variety of chemical products. Various applications may require specialized analytical procedures. For example, some of the procedures developed for the coke industry, such as expansion or contraction during carbonization, have little value to the power generation industry. Even for a single application, the type of analysis needed can depend on the source and/or general nature of the coal. This section provides a general overview of the types of analytical procedures commonly applied to coal from the perspective of the user of this information, not the producer. The intent is not to detail laboratory procedures, but rather to discuss the application of commonly used laboratory tests in coal preparation. Accordingly, laboratory procedures are categorized by type of information produced. Gravimetric Analysis Procedures that produce weight-based information (parts per million, pounds per cubic foot, or weight percent). Such analyses can relate to the coal's physical, chemical, or mineralogical characteristics. Volumetric Analysis Procedures that produce volume-based information (amount of a mineral present as a volume percent). The primary source of volumetric information is from petrographic analysis. Application Tests Procedures that measure some characteristic of coal that has been empirically related to some application or handling or processing step. Typically, these procedures attempt to duplicate some aspect of the commercial application at laboratory scale and may produce information in the form of an index. Applications procedures do not measure a single component of the coal but infer the combined effect of multiple components. Each class of information is discussed in the order listed. References are provided as a source of more detailed information. The American Society for Testing and Materials (ASTM) publishes the most inclusive reference to analytical procedures. This publication,16 which is revised annually, provides extensive information concerning generally accepted methods of laboratory analysis. ASTM also provides standards for sampling and some information concerning sample handling.

Jan 1, 1991

By J. A. McKeown, B. M. Sanders, A. Dadgar, R. H. Sergent

This paper describes the leaching of gold with Geobrom® 3400 from a very rich (6.2 kg/tonne) black sand concentrate and its subsequent recovery by ion exchange resins and solvent extraction. The dissolution of gold from black sand ranged from 94 to 96%. Gold loadings and recoveries of nearly 100% were achieved by both ion exchange and solvent extraction methods. The kinetics and equilibrium of loading gold onto ion exchange resins and its elution from the resin were studied. The commercial ion exchange resins PAZ®- 4, DOVEX®- 21K, and Amberlite® XAD- 7, and Great Lakes Chemical experimental GLR-30 were evaluated in this work. Diethylene glycol dibutyl ether was used in all the solvent extraction work for gold recovery from Geobrom leach solution. The consumption of Geobrom was about 130 kg per tonne of the concentrate processed. Therefore, the cost of lixiviant to extract 3.11 x l0-2 kg of gold from the black sand was only about $1.00. Based on the electrochemical regeneration of bromine, the economics of bromine process vs. cyanidation were investigated.

Jan 1, 1990

By G. C. Eggleston, W. E. Keck, W. C. Lowry

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

By W. G. Q. Johnston, J. S. Fox

"A semi-continuous belt of Aphebian magnesian extrusive and related sub volcanic rocks has been delineated by the authors over a distance of 150 kilometres in the central La Ronge lithostructural domain in Saskatchewan. They range in composition from peridotite to basalt and attain true thicknesses of up to 800 metres. For the most part, they are confined to a basal position in the La Ronge/Wasekwan metavolcanic sequence, and appear to have been extruded onto sialic crust. However, at Lynn Lake, Manitoba, in the eastern continuation of the domain, similar rocks seem to be found only at a relatively high stratigraphic level.Although metamorphism seems to have obliterated any quench textures that may have existed in these rocks, ultramafic pyroclastics, pillows and amygdules as well as intercalated, fine-grained clastic sediment attest to the volcanic nature of these rocks. Bulk chemical analyses indicate that these rocks are heterogeneous, with komatiites, tholeiitic picrites and even rocks with some of the characteristics of boninite all being present. The close temporal and spatial relationship of ""boninites"" and komatiites in the belt may suggest a high degree of Aphebian mantle inhomogeneity in the domain.Nickel-copper mineralization has been found in differentiated tholeiitic stocks within the La Range domain (e.g., at Lynn Lake), but none has yet been found in the ultramafic volcanics. However, the tholeiitic picrites do host one economic gold deposit - the Agassiz Mine at Lynn Lake .Because of the depleted nature of their mantle source, the ""boninites"" of the domain are not considered to be likely hosts for mantle-derived nickel sulphide mineralization. However, the opposite is true of the komatiites, and this points to the need for whole-rock geochemistry in setting priorities for nickel exploration in the belt. In contrast, all of the magnesian rocks of the domain probably have the same gold potential. Inasmuch as the geophysical response to gold mineralization in the domain is likely to be unpredictable, lake-sediment geochemistry, followed by base-of-till and/or alteration oriented lithogeochemistry, should be emphasized during gold exploration."

Jan 1, 1981

The paper examines the possibility of applying the monolithic packing technique developed in the UK to the division of wide development drivages in Australia, so enabling double entries for longwall retreat panels to be created from shortwall units. The monolithic pack of the UK therefore becomes a monolithic partition in this proposed Australian application. A method developed for the analysis of the load development in packs installed behind longwall advancing faces is adapted and used to predict the support performance of the monolithic partition. Conclusions are made regarding partition construction and possible rates of advance.

Jan 1, 1986

By E. C. Wade, R. D. Valentine

This paper describes a computer applications engineering system and it's use to apply a thermal dryer fan motor in a coal preparation plant. The computer hardware and software systems are described to indicate the general approach taken and a specific case study is reviewed to show how computer power is brought to projects in the coal industry.

Jan 1, 1983

By N. Patel

Many factors, from engineering and design to supply, installation, and operation affect the service lifespan of cast refractory linings. If a shortcoming occurs at any of these stages, the lining lifespan can be drastically reduced. Although not every aspect that can affect a cast refractory lining?s lifespan is outlined here, a few key points are highlighted, with an emphasis on the various installation parameters. Keywords cast linings, refractory lifespan, lining engineering and design, lining supply, lining installation, curing, dry-out.

Aug 1, 2013

By J. William Ganser

This paper is one of a series being prepared by the United States Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1931

By R. M. Clowes

LITHOPROBE is a collaborative, multidisciplinary research project that is providing new insights into the tectonic evolution of the North American continent through its work within 10 study areas across Canada. For the mining industry, such results provide a well-constrained regional framework and better understanding of the tectonic processes that lead to the development of ore deposits. In mining camps, seismic-reflection methods have proven effective in imaging shallow to moderately dipping lithologic contacts as well as structural features and, in some cases, have been used for the direct detection of orebodies. Here, short case histories are provided for the Abitibi greenstone belt (VMS deposits) in Quebec and the Thompson nickel belt in Manitoba.

Jan 1, 2002

Since the 1989 Loma Prieta Earthquake in the San Francisco Bay Area, the California Department of Transportation (CALTRANS) has accelerated seismic upgrading of their bridges. Many structures can be improved with the simple addition of hinge seat restrainers. Others require modification of column bents and superstructure to column connections. Often, footing retrofits are necessary, which require the addition of tension/compression elements (compression piling and tiedowns anchors) to resist overturning moments substantially larger than those originally used for footing design. These footing retrofits may include doweled reinforced concrete footing extensions or new pile caps which transmit forces to either driven steel or drilled concrete piles. In some cases, installation of these traditional piling elements is expensive, impractical or impossible due to: low overhead clearance, ground obstructions, high water table, noise or vibration sensitivity, or the inability to laterally expand the existing plan dimensions of the footing. In the latter case, one practical option is to attach small diameter drilled and grouted tension/compression piling elements (Pin Piles) to the existing footing. The footing may be strengthened with dowels and added concrete thickness or there may be a reduced shear span due to the installation of larger or jacketed columns. A reduction of elements is available with a Pin Pile alternative, particularly when the selection of traditional standard piles is governed by the reduced tension/uplift capacity available from the traditional elements, since Pin Piles exhibit superior uplift performance.

Jan 1, 1993