Search Documents

WHEN the new sulphide plant started to roll at Chuquicamata last July, we broached the matter of looking in on this historic event to Burr Wheeler, then executive vice president of Chile Exploration Co. (Chilex executive offices are housed with the parent company, Anaconda, at 25 Broadway which is 23 hours and 15 minutes closer to the AIME office than the mine, counting air and automobile travel). Mr. Wheeler was at Chuqui when they turned the first shovelful of earth, has an understandable pride and affection in the mine, and kindly offered to make all arrangements. As a guest of Chilex, physical exam, injections, police clearance, passport, and airline reservations on the crack Panagra airline are procured swiftly and almost painlessly. Winter clothes were advised by Mr. Wheeler and D. M. Dunbar, who is the former's assistant and a seasoned Chuqui-ite. Both of these gentlemen obviously prefer Chuqui climate, with 364 days of sunshine, 1 ½ -in. rainfall, rare atmosphere of 10,000 ft elevation, Christmas-time earthquakes, and howling winds through June and July to the vicissitudes of New York weather. Panagra's de luxe DC-6 noses in toward land at Antofagasta, Chile, the supply and embarkation port for Chuquicamata. The Coastal Range, completely barren of green, thrusts a spur far out into the Pacific creating a crescent-shaped and protected harbor at Antofagasta. Beach gives way to pampa, to hills, and the only variation in scenery is in topographic relief. Chilex's reception committee in the person of the alert and amiable Bob Condit, assistant port agent, takes care of everything: immigration, interviews by the local press, baggage, transportation, and introduction to Chilean cuisine. The drive up to Chuqui takes about three hours, on the only two lane highway in northern Chile; hard surfaced, with a few kilometers of repair work in progress. We were fortunate to make the trip with manager Charles Brinckerhoff, who arrived the same day at Antofagasta from the seat of government at Santiago where he goes frequently to keep in touch with the company's Santiago office.

Jan 1, 1952

By Andrew B. Cecala, Robert J. Timko, Christopher J. Pritchard

As mine venti1ation systems become more complex, it is increasingly difficult to supply fresh air to the working face. A high percentage of the fresh air entering a mine never reaches the working face because it short circuits through stoppings and doors, exiting the mine without being utilized. When ventilation limits are reached, the only option presently available to most U.S. mines is to sink a new shaft - an extremely expensive undertaking that many companies cannot afford. Reusing or recirculating a percentage of ventilating airflow may make it possible for some mines to remain operational while maintaining a safe environment for workers. Such a study was performed at a trona mine in Granger. Wyoming. A vane axial fan was used to recirculate approximately 9.4 m /s (20,000 cfm), 25% of the total ventilating airflow, back to the working face area of a three-entry continuous miner section. This study involved two evaluations: the first when the face was 305m (1,000 ft) from the recirculation fan, the second when the face was 610m (2,000 ft) from the fan. The evaluation consisted of monitoring the mine atmosphere for respirable dust, methane (CH4). carbon monoxide (CO), and nitric oxide (NO), at various locations in the intake and return entries. Several shifts were monitored, with and without the recirculation system in operation. With the recirculation system in operation. there was an increase in measured respirable dust concentrations in the intake along with a slight increase in the mine temperature (1.67°C). There were also some minor changes in CO and NO levels in the intake entry, but this seemed to depend on the proximity of the instruments to the turn-around point for the diesel haulage vehicles, than to whether the recirculation system was or was not in use.

Jan 1, 1989

By Ellen H. Richards

It is of importance to analysts to have a ready means of detecting the presence of small quantities of titaninm in iron ores and in certain fluxes and slags. The method given in Elderhorst's Blowpipe Analysis (fusion with potassium hydrogen sulphate) requires considerable practice, in order so to regulate the heat that the titanium oxide shall become soluble. In Brash's Determinative Mineralogy is found a method which, at least in inexperienced hands, has given better results, i. e., fusion of the substance to be tested with sodium carbonate on charcoal in the reducing flame. The solution in hydrochloric acid of the bead thus obtained, boiled with tin or zinc, gives the characteristic violet color; but when the mineral contains less than four per cent. of titanium oxide, long boiling and consequent concentration is necessary. In fact the test would seem to be much less delicate than is generally supposed. In the course of some analyses I quite accidentally found that a peculiar color is given to turmeric paper by solutions of titanium chloride. This color is hard to describe, being modified by the quantity of ferric chloride present in the solution ; but it is neither the orange of zirconia nor the red of' boron. It is rather a dull shade of purple, arid is easily recognized when the paper is dried, although the color fades in a few hours. By this means a solution containing .015 per cent. of titanium oxide can easily be tested. The same solution, treated with tin, required to be concentrated to one-tenth its bulk before a decided color could be obtained. The color given to turmeric paper is intensified after the solution has been treated with tin. This and some other indications show that the best shade of color is given by the titanons chloride rather than by the titanic chloride, and no other salt of titanium than the chloride has been found to give the color. Another peculiar property of titanium salts has come tinder my observation. When titaniferous minerals are soluble in nitric acid, and the solution is subjected to the action of the battery, the soluble titanium salt is converted into the insoluble oxide and appears on the electrode, in some cases, as a white coating; this

Jan 1, 1883

By Jackson R. Pressley, Bruce Vandenberg

An explosive’s velocity of detonation, (VOD), can be used to indicate a number of important characteristics regarding the product’s performance, under specific field and test conditions.

Jan 1, 1997

By E. G. Davis

A research program to evaluate the use of ceramic die inserts for ferrous diecasting was initiated by the Bureau of Mines at its Tuscaloosa Research Center. Data were compiled from the literature to characterize selected ceramic materials with respect to thermal properties, thermal-shock resistance factors, chemical reactions with molten metals, and processes required to form die components. With this information and a computer model developed for predicting temperature and stress patterns induced in ceramic materials during simulated ferrous diecasting operations, 27 candidate materials were evaluated. After evaluation, only 15 were considered for testing in an apparatus constructed to immerse the ceramic specimens in molten cast iron. Of these, 13 were tested in a modified testing unit in which cast iron was poured onto the specimens. These tests resulted in the selection of three materials for further testing: boron carbonitride (50 pct B4C:5O pct BN), boron nitride-grade M (BN-M, 40 pct BN, 60 pct Si02), and pyrolytic boron nitride (PBN). Tests in a gravity-flow die unit showed that PBN was thermal-shock resistant and could be used in diecasting of ferrous metals.

Jan 1, 1981

By Gloria Fernández

La contaminación por drenaje ácido de mina se considera como la responsabilidad ambiental y económica más grande que actualmente enfrenta la industria minera. En ese sentido, se delimita las áreas afectadas mediante la perforación de pozos de monitoreo a través de un estudio geofísico previo. Por ello, el presente trabajo señala los métodos geofísicos como herramientas que pueden ayudar a delimitar y mapear las zonas afectadas por la contaminación proveniente de drenaje y filtraciones que va desde canchas de relave, pilas de lixiviación a minas abandonadas, etc.

Aug 25, 2002

This case history refers to the detonation of the two largest chemical explosions on the Australian continent. An important element of feasibility studies and construction guidance included prediction of fragmentation results and ground vibration effects for the detonation of two very large "coyote" blasts, consisting of mined tunnels filled with explosives. The larger of the two blasts contained nearly 1 1/4 million pounds of explosives detonated instantaneously. The explosives were placed in specially designed tunnels under a quartzite mountain for the purpose of generating rock fill for the main dam on the project.

Jan 1, 1995

By Robert Roby

The Mouat copper-nickel deposit in Stillwater County, south-central Montana, was examined by Paul T. Allsman, an engineer of the Bureau of Mines, in 1939. Because of the strategic importance of nickel, a project was executed by John East, Jr., J. J. Naughton, and E. W. Newman, engineers of the Bureau, to further delimit some of the copper-nickel sulfide-bearing bodies that had been discovered by the Anaconda Copper Mining. Co. in 1937 and to investigate the central part of the deposit, which had not been drilled previously. This report is based largely upon the results of the. Bureau of Mines investigation and the results of exploration by the Anaconda Copper Mining Co. In addition, a brief description is given of some other copper-nickel sulfide-bearing deposits along tho Stillwater Complex.

Jan 1, 1949

By Xuewei Lv, Maojun Zhou, Xiaobo Huang, Rende Zhang

"The characterization of the surface roughness of the mineral particles is of vital importance for the studies of the mineral processing. In this study, an evaluation of the roughness of the iron ore particles, with the measurements of size distribution and the measurements of specific surface area with the liquid nitrogen absorption, was developed. The main theory of this method is the fact that the roughness of the particle influences the specific surface area apparently. The specific surface area of the particles can be measured with the laser diffraction method and the liquid nitrogen absorption method. The influence of the surface roughness of the particle can be measured with the nitrogen absorption and cannot be measured with the laser diffraction. Therefore, the roughness can be got by comparing the specific surface area with two measurement methods.IntroductionThe characterization of the surface roughness of the mineral particles is of vital importance for the studies of the mineral processing. There are three main methods for measuring the size distribution of mineral particles: sieving, laser diffraction, and sedimentationl). Many techniques involve sedimentation such as the Horiba2, 3) and the Cyclo-sizer1). In the mineral industry, size distribution is usually determined by sieving because it can be carried out accurately for all particle sizes larger than 45 . The preferred method to obtain the size distribution of finer particles is laser diffractometry. The technique has several advantages: it produces measurements in a few minutes with considerably less labor compared with the cyclo-sizer and for a range of sizes considerably wider in comparison with the sedigraph4). The equivalent-sphere size distribution reported by laser diffractometry is valid for metallurgical calculations and can be routinely used in mineral processing plants. The surface area of the particles can be measured by the BET method of nitrogen adsorption, or it can be calculated from the size distribution. However, the latter calculation requires the size distribution to be accurately known across the whole size range, and assumptions have to be made about the shapes and surface roughness of the particles and presence or absence of pores (see below). The BET method is based on the physical adsorption of gas over the whole exposed surface area and measures the surface area stemming from the roughness and open pores on the surface of the particle5). The calculation of the surface area from the size distribution is usually based on the assumption that all the particles are smooth spheres, without considering the shape and/or roughness of the particles. Determining the surface roughness of the particle with these methods, is the objective of this study."

Jan 1, 2012

By Odyssey Marine Exploration

Odyssey is a world leader in marine exploration and has undertaken expeditions in varying environments throughout the world addressing many commercial and regulatory demands. Odyssey works in a variety of settings such as shallow coastal territorial waters, abyssal plains in exclusive economic zones, and high seas in international waters on projects involving mineral exploration, environmental analysis, oceanographic survey, and recovery operations. Odyssey Marine Exploration (Odyssey) excels in adaptively managing programs from initial concept through realization of commercial goals while successfully satisfying the regulatory and engineering demands of deep sea projects. This poster presentation reveals best practices throughout a project life cycle and presents case studies in areas including but not limited to: • Research practices to identify and define valuable subsea resources • Project planning and licensing to achieve project goals and meet regulatory requirements • Optimizing offshore operations to achieve desired results • Designing projects to support processing and commercial programs

Jan 1, 2018

By William J. McCloy, Robert L. Gamble

A coal-fired fluidized bed steam generator rated at 12.6 kg/s has demonstrated the industrial and institutional application of fluidized bed combustion by burning high sulfur coal in an environmentally acceptable manner within a populated area. Designed to provide steam for heating and cooling, the unit was placed into service at Georgetown University in Washington, DC, and has already logged 5275 hours.* The unit has consistently operated well within Washington's strict regulations governing emissions of sulfur dioxide (SO2), nitrogen oxides (NOx), and particulates. The Georgetown program, cofunded by the university and the US Department of Energy, has shown that fluidized bed combustion is a promising way to realize the full potential of coal, the nation's most abundant energy resource. In a fluidized bed steam generator, a layer of granular limestone is placed on top of a grid designed to prevent particles from falling through. Air is passed upward through the bed with sufficient force to lift and float the particles. At this point the bed material resembles a boiling liquid. Crushed coal is then introduced into the bed and ignited. When high sulfur coal is burned, limestone absorbs the SO2 produced. The operating temperature of a fluidized bed steam generator is relatively low (approximately 871°C). As a result, NO, formation is minimal. Another potential problem encountered in burning coal is fly ash, a form of particulate. A feature of the fluidized bed design, developed by Foster Wheeler Energy Corp., is a fly ash reinjection system. Fly ash is reintroduced into the bed where it is burned again, thereby enhancing fuel efficiency. Nearly all remaining fly ash is captured by a baghouse dust collector. At Georgetown, the fluidized bed steam generator and all auxiliary equipment are enclosed in a structure aesthetically compatible with the surrounding university complex. The steam generator has two separate beds that can be fired independently, and operation to date has been with one and two beds in service, based on steam load demand. During several operating periods, when the fluidized bed unit was the only boiler in service, it supplied all the steam required by the 18.5 hm2 of buildings on campus. Initially fired with low sulfur coal, the unit was quickly switched over to higher sulfur fuel which will be used most of the time.

Jan 3, 1981

By R. B. Woodworth

INTRODUCTION IN the sinking of bore holes, there are but two fundamental operations -drilling and hoisting,-which determine in the main the character of drilling mechanism and structures. There are endless ramifications, however, in the execution of these fundamental operations, according to the purposes for which the bore holes are drilled, their maintenance after completion, the protection and convenience of workmen, etc. The three main lines of use for bore holes are in mineral exploration, the sinking of water and salt wells, and the exploitation of petroleum and natural gas. This paper has to do more especially with the last. Here again there are many divergences. Wells may be drilled by either the percussive, the hydraulic, or the abrasive method. Finally, each of these methods, as applied by drillers of diverse nationalities, has followed somewhat different lines of development. The American system of cable-tool drilling has perhaps had the widest application; the hydraulic rotary is also in extensive use; but the Canadian system, the Galician system, and the Russian free-fall system all have their points of recognized merit and are preferred by operators accustomed to their use. These differences in drilling procedure, which rest ultimately on essential variations in geological conditions, are reflected in the chilling structures as well as in the drilling mechanism. The purpose of the present paper is to record those stages in the development of the application of steel to the construction of drilling mechanism and structures with which the writer has been intimately associated, and to contribute to the history of the art of drilling other data acquired in the course of his personal investigations. It is necessarily limited by reason of space to American practice, with especial reference, therefore, to the cable-tool system and the hydraulic rotary method of drilling wells for oil and gas.

Jan 11, 1915

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

By Slavoljub D. Maksimovic

At some coal mines, methane gas is released during raise drilling. At the request of the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, the Bureau of Mines conducted ventilation surveys at different raise drill sites to assess various methods of reducing methane concentration. The resulting data indicate that raise drill shaft cavities are ventilated by air compressors, vacuum pumps, auxiliary blower fans, and free intake air from the surface. The compressors, pumps, and fans operate simultaneously or separately. At the bottom of the shaft cavities, ventilation is controlled by regulators and airlocks. Methane is monitored, measured, and periodically sampled on the surface, at the bottom, and at different levels in the shaft cavities. Maximum concentration of 3.5 percent was measured in one shaft in West Virginia. Air velocity down the raise drill shafts is always very low, Maximum recorded air down the drill stem was 3,000 cfm, which can be increased by adding air compressors. The best way to ventilate shaft cavities is through the simultaneous use of air compressors and vacuum pumps. If the methane concentration cannot be reduced with additional compressors, then the inside diameter of the drill rod should be increased, or larger pilot hole drill bits should be used.

Jan 1, 1981

By Ernest W. Johnson

Diamond, drilling of some blast holes in stoning operations is practised in at least two iron mines in the Lake Superior district - the Soudan mine of the Oliver Iron Mining Co., on the Vermilion range at Soudan, Minn., and the Anvil-Palms mine, operated by Pickands, Bather & Co., on the Gogebic range at Bessemer, Mich. Diamond drilling, at the Soudan nine has partly replaced percussion drilling because of the extreme hardness of the ore and of the lean formation. According to Wolff,4/ the jasper or lean formation in this mine is the hardest rock regularly drilled in any commercial operation.

Jan 1, 1945

By Samuel M. Brock

In recent years society has become increasingly concerned with maintaining and improving the quality of environment. Thus, public interest and concern with pollution problems is now high. This is reflected in recent federal and state efforts to formulate new legislation to prevent pollution and strengthen existing pollution laws. In reviewing literature pertaining to pollution problems, it is possible to distinguish many common elements. The most outstanding of these is the failure of the market to guarantee that private firms responding to price signals generated in the marketplace will make decisions leading to optimal resource use. Cases of market failure in allocating natural resources according to the wants of society frequently are due to the presence of technical externalities, or side-use effects.59 These roughly and generally can be defined as interdependencies among production and consumption units, the impacts of which are exerted other than through the market. They are, in other words, extra-market relationships. The economic unit generating external effects does not take them into account in decision-making. Thus, the tendency is for the unit to produce either more than society desires or not enough. In such cases society often has intervened in the decision-making process. This intervention frequently has taken the form of legislation to regulate production and consumption activities. Thus, a body of institutions, which acts as a constraint in decision-making processes, has materialized. These institutions are often far more influential in their effect upon resource use than are the forces of supply and demand acting in the marketplace. The problem of environmental pollution is essentially the problem of handling residuals which are the byproduct of all production and consumption activities which take place in the economy.2 These residuals are emitted into the air and water and disposed of on the land. They are interrelated, in that efforts to control emissions into the air or water can result in the production of solid wastes, which then present disposal problems. It is convenient to separate residuals by the type of pollution they cause-air, water, and land while remembering that these problems are related and that solutions may require coordinated effort.1 Residuals may be produced in both production processes and consumption. Residuals produced in production by the mineral industry, or firms utilizing its products, range from emission of sulfur dioxide by steam generating plants to radioactive mill tailings produced in the course of mining uranium.. Residuals associated with consumption are generated mainly through transportation of members of the household, space heating, and in the disposal of solid wastes, including refuse and junk autos. Residuals associated with both production and consumption receive attention in ensuing sections of this chapter.

Jan 1, 1976

By S. Makni, C. Bazin, D. Hodouin

This paper reviews approaches for the real-time estimation of mass flow rates and assays using data from on-stream analyzers and flowmeters in a flotation circuit. Results obtained using one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1998

BEING at the crossroads, metaphorically speaking, seldom has the advantages of the literal sense of the words. One seldom has precise knowledge of the existence of the metaphorical crossroads or forks in the road of life. A case in point is the Committee on Education of the Engineers' Council for Professional Development, which for twenty years has been accrediting the engineering curricula in the educational institutions of the United States. The committee is now at odds with itself and with the National Council of State Boards of Engineering Examiners over the accrediting of courses which in the opinion of many engineers are not strictly speaking engineering curricula at all. Such courses include: fire protection engineering, crystal engineering, nuclear engineering, and geological engineering. The crossroads might be placed arbitrarily somewhere between 1936 and 1938 when the committee first started accrediting curricula and included the first course in industrial engineering. Purists might argue that the committee first wandered from the straight and narrow when it recognized subdivision of engineering into the major branches of mining, metallurgical, civil, mechanical, electrical, and chemical engineering. Accrediting is certainly an important function because it provides a standard for engineering education and it should be done on a national basis by an unbiased group like the Education Committee of ECPD. Students, educational institutions, and industry derive great benefit from proper standards. The autonomous State Boards of Engineering Examiners have long accepted ECPD accreditation as evidence of the required academic training of engineers aspiring to licensing. But the State Boards today question the wisdom of applying the name engineer to graduates of some of the so-called fringe curricula. The Education Committee, having gone so far in accrediting some of them, has numerous applications pending for accreditation of similar curricula and even new courses never before accredited. Arguments against recognizing highly specialized engineering curricula are numerous. The Salary Stabilization Board has disallowed industrial engineering from classification as engineering for its purposes. A graduate of a specialized course in geological engineering at a school in the Southwest slanted heavily for practice in the petroleum industry might not be interchangeable with a graduate of a similarly designated curricula at one of the institutions in the North Central states where the emphasis might be on metallic. mineral deposits. Industry in general should not expect the universities to supply a degree in each of the specialized engineering classifications it might set up for purposes of salary or job designation. Having gone so far, it is easy to understand the difficulty of the Education Committee. ECPD might well call a moratorium for the purpose of taking stock of its position. If the present trend is allowed to continue, it is apparent that an engineering institution could be subdivided into a multiplicity of departments teaching specialized curricula resulting in a subordination of the basic concepts of engineering. Although the parallel of the medical profession is trite, it should be pointed out that degrees in medicine are not labelled by the numerous specialities practiced by doctors. For practical purposes the ECPD would do well to accept the fact that the crossroads have been overreached "and protect the engineering profession by coming up with minimum standards for an engineering curriculum.

Jan 1, 1952

By B D. Sowerby, N G. Cutmore

Improved process control can be achieved through the accurate and reliable on-line measurement of critical process parameters in real time. Over the past few decades on-line analysis techniques have been developed and applied in the mineral and energy industries for the measurement of process stream composition, mineralogy, particle size and flow rates. This has led to increased throughput and product quality while reducing processing costs and minimising emissions. The support of a sustainable mineral processing industry will require the further development of on-line analysis and control technologies. The application of developments in instrumentation combined with improved control strategies will lead to improvements in process efficiency resulting in large economic benefits to the industry, reduced energy usage and lower process emissions. There is a clear convergence of interests in being able to better measure and control minerals processing in terms of the triple bottom line of economic, social and environmental impacts. Technology is increasingly becoming available enabling measurement across the entire spectrum of minerals processing from mining to hydrometallurgy and pyrometallurgy. CSIRO is developing a range of these new technologies. A number of these developments are discussed in the present paper, namely: on-line particle size analysis and acoustic emission methods to enhance the control and optimisation of grinding circuits; on-line mineralogy of dry powders and slurries; on-line bulk elemental analysers for application on conveyor belts and in smelters; and the development of new sensing technologies for sorting base metal ores.

Jan 1, 2002

AT the Non-ferrous Metallurgy session on Wednes-day afternoon, R. M. Roosevelt, vice-president of the Eagle-Picher Lead Co., presided. The paper "Sug-gested Improvements for Smelting Copper in the Rever-beratory Furnace," by G. L. Oldright and F. W. Schroeder, was presented by. Mr. Oldright. It was brought out that lessening of dusting of the charge would increase the life of the arch at present operating temperatures, but will not allow much higher tempera-tures to be used unless dusting can be entirely elim-inated. The best opportunity for improving rever-beratory practice lies in the use of still higher tempera-tures but this requires the development of refractories superior to those now used. There was an interesting discussion of the facts brought out. The paper. on the "Formation and Decomposition of Zinc Ferrite," by

Jan 3, 1928