Search Documents

By Charles G. Kemsley

IN view of the truly remarkable development of special steels for special purposes, the mining industry has for years looked forward to a time when steel makers would come forward with a product which would be an improvement over the straight carbon steel which has always held the field for drilling rock. In order to avoid making changes in conventional shop practice, the industry has perhaps been too insistent upon obtaining a water hardening steel which could be handled in the blacksmith shop by long established methods. As early as 1932 or 1933, an oil-hardening tool-steel of the one per cent carbon, plus chrome, plus molybdenum type was applied to hollow drill steel. It was known as a hard as well as a tough steel, and one that, theoretically, should give a good account of itself as a rock drill, if properly heat-treated; and so it has proved in actual trials. There were numerous deterrents which retarded adoption of this steel. For several years there has been a constant improvement in the drilling qualities of the straight carbon steel, and, considering the higher unit price ? of the alloy, there has been considerable doubt in the minds of some mining? men as to what advantage there might be in the use of alloy over straight carbon for hollow drill steel. The alloy being an oil-hardening steel, its adoption meant having two kinds of steel in the mine, for a time, and that spelled trouble, unless some positive means of identification was adopted. The hardening and forging ranges of alloy steel being narrow also made necessary much closer control over these operations if poor results were to be avoided. These thoughts undoubtedly prevented its use becoming wide-spread, for, as a matter of actual record, less than fifteen per cent of all the hollow drill steel used in Canada today is alloy.

Jan 1, 1942

By F. S. McNicholas

IN the writer's opinion the term "block caving" has been rather loosely applied to a general principle of mining, and therefore detailed classification of caving methods and draw, together with the characteristics required for each method, will fill a desired need. Selection of caving method should be made only after a study of all governing conditions, such as size of orebody, lateral and vertical extent of ore-body, attitude, treatment demands, possible resultant pressures, and cost and profit comparison of methods. Successful caving methods can be classified under six main headings: (1) Full-protected block caving, (2) semi-protected block caving, (3) unprotected block caving, (4) full-panel caving, (5) half block-panel caving, (6) block-panel caving. The methods and factors governing choice of method are shown in Table I. Full-protected Block Caving Full-protected block caving consists of develop-ing, undercutting, and drawing to exhaustion a block of ore of predetermined size without coordination of mining or draw with adjoining areas. The block is mined and drawn as an independent unit (Fig. 1). Full-protected block caving demands that mining and draw cannot be done against unconsolidated capping in adjoining caved and exhausted blocks. Two sides of block are against solid. Caved capping must be allowed to consolidate for a suitable period, usually not less than one year. Pillars may be left in lieu of consolidated capping (Fig. 2). The advantages of full-protected block, caving are: (1) A definite area is developed, mined, and drawn as a unit so that all work may be completed, the block drawn to exhaustion in the minimum length of time, and the area then abandoned. (? Production is not restrained because of coordina1, on with adjoining areas. (3) Records of draw and caved reserve of ore are good. Upon abanwnment of the block, accountability for production is closed out with no carry-over to adjoining areas. The disadvantages of full-protected block caving are: (1) Side dilution from the draw adjacent to the consolidated capping may be serious, particularly where capping does not consolidate sufficiently in the allotted time. (2) Boundary weakening is needed on the solid sides of the block except in weak rocks. (3) Maximum cantilever and compression effect to aid caving and fragmentation may not be secured since the draw should proceed from the solid to the consolidated capping to minimize side dilution. However, undercutting from the loose (caved capping) to the solid with a slight initial draw in the same manner will develop cantilever effect. (4) A period of at least one year, more is usually desirable, must be allowed for caved capping ,to consolidate before mining the adjoining block, depending upon the characteristics of the capping. (5) Capping may not consolidate sufficiently in the time that can be allowed. Full-protected block caving is indicated where: (1) The ground is weak and heavy and workings

Jan 1, 1952

By Pamela Castillo, Marcia Muñoz, Rodrigo Luca, Brian Townley, Fernando López

In the present study we discuss the value of multi-element geochemistry as a tool for semi-quantitative to quantitative bulk mineral characterization in geological and geo-metallurgical modeling of porphyry copper type deposits, with an emphasis on hydrothermal alteration associations, types and intensities. In mine production of porphyry copper deposits much effort is placed on ore grade and geological modeling, applied for predictive mineral processing behavior, from blasting, grinding, leaching or flotation, down to waste disposal and environmental management. High confidence geological models are commonly based on geological mapping of drill core and surface/ underground exposures, combined with discrete mineral characterization (e.g., petrography, QEMSCAN®, spectroscopy, etc.). Unfortunately these are expensive and applied to limited numbers of samples, thus lacking sufficient representation and not suitable for geo-statistical modeling. In addition, geological mapping always presents uncertainty, based mostly on qualitative estimates. The combination of information usually provides geological models that are hard to combine with geo-metallurgical data, much less with mineral processing predictive behavior models. The advent of multi-element geochemistry, at low cost, has allowed employment of such tools massively, yet little use is given to the data, usually focused on elements of economic interest (main ore and credits) and elements of negative impact to concentrates and/or process. Geochemistry reflects the mineral composition of rocks, thus allowing characterization of lithology, alteration types and intensities, and mineralization. As examples of such applications we present generic classification techniques which were developed on various porphyry copper deposits of northern Chile, these based on multi-element geochemistry, allowing for semi-quantitative to quantitative high resolution modeling of key aspects of lithology, hydrothermal alteration and mineralization, and which may be cross-referenced to metallurgical test samples and by that, to geo-metallurgical properties of rocks and modeling. In addition, as data is quantitative and continuous, modelling of gangue can benefit from geo-statistical modeling.

Jan 1, 2018

By Gerd L. Klinkenborg

Throughout the history of the development of mechanical conveyor systems, it has always been an established condition that loads are received at one end of a single-belt conveyor and discharged at the other end, in a point-to-point, manner. In systems designed for the continuous transport of granular materials, vertical or horizontal changes in; direction have always necessitated two or mope single-belt conveyor units, with a corresponding number of motors, assemblies and attendant mechanical and human or electronic controls. Besides these high-cost factors, every change in the system's direction also calls for a transfer point that involves a drop-back of the material from one level to another with some loss of the material and, in many cases, unwanted additional granulation. Where changes in the location of the discharge point are wanted, the conventional single-belt conveyor must either be replaced by a shorter or longer unit or additional units purchased and installed, or existing units rearranged. This can take days or weeks, and involve special expenditures as well as loss of valuable production time.

Jan 1, 1962

By James W. Martin, Robert R. Faddick

INTRODUCTION Virtually every sector of society in our country feels the impact of tunnels, either through the transportation of water, commodities, or people. The economic implications are staggering. The Committee on Rapid Excavation (1) reported that during the near future, 1968-1975, underground excavation activity will comprise 946 miles of tunnels (subways: 85 miles; underground urban highways: 123 miles; intercity highway tunnels: 210 miles; water supply tunnels: 528 miles) and 5,119 million tons of crude ore; metals: 874 million tons; nonmetals: 899 million tons; and coal: 3,346 million tons. It is estimated that the cumulative demand for underground excavation in the decade 1970-1979 will be 13 billion dollars for construction-oriented demand and 16 billion dollars for mining-oriented demand. The respective figures for the decade 1980-1989 are estimated at 22 billion dollars and 18 billion dollars. Of the many advantages claimed for tunnels (2, 3, 4, 5) the environmental considerations are becoming increasingly important. Transportation tunnels particularly for rapid transit systems, offer reductions in noise pollution and air pollution while improving aesthetics and optimizing land use (fewer problems of right-of-way and disruption of utilities). Considerable interest has been shown recently in sub-surface construction and mining (6, 7, 8). Recognizing the future demands for tunnels has led to considerable study of methods to improve rates of tunnel advance per day, safety, and the overall economics. The search for higher rates of advance has Led away from what has heap termed conventional methods (drilling

Jan 1, 1974

By P. D. Bergman

To assess the efficacy and economics of producing power from coal, four open-cycle magnetohydrodynamic (MHD) processing schemes were selected for study. Each involved a different mode of coal combustion and level of gas cleanliness. The options considered were: (1) coal burned in a slagging combustor; (2) suspension gasification with slag removal prior to combustion; (3) parallel cyclone combustors, one operating fuel rich and the other operating with excess air; and (4) suspension gasification by the hot exhaust gases from the MHO duct with ash removed prior to combustion. Option 1 has the highest ash content in the combustion plasma and as a result would have the greatest operational difficulties associated with it. Options 2 and 4 have the cleanest MHD combustion plasma. For coal priced at $4/ton, the power generating cost of option 4,11.78 mills/Kw-hr, is the highest, with Option 1, at 9.04 mills/kW-hr the lowest. These costs may be compared with a conventional power cost of 9.92 mills/kW-hr for the late seventies. Capital costs of three of the four options were competitive with those of conventional thermal power plants employing stack gas S02 cleanup systems. Option 2 has the most favorable combination of operating characteristics and power cost. It was concluded that a clean, high-temperature working fluid can probably be produced from coal without leading to depressed system efficiencies and exorbitant capital costs.

Jan 1, 1973

By William J. Campbell

The purpose of this investigation by the Federal Bureau of Mines was to design and construct a fluorescent X-ray spectrograph for dynamic rate studies of selective oxidation in molten metals and to establish basic principles for interpretation of data obtained by this method. An X-ray spectrograph was constructed in which the sample holder is a resistance wound furnace; it was operated up to 800° C. in oxidizing atmospheres. No difficulties were experienced with the cooling or heating systems nor with the protective layer of mica around the X-ray tube window, even though the oxidizing surface of the metal is only 0.5 inch from the X-ray tube window, Means are provided for heating under controlled atmospheres for selected time? temperature cycles.

Jan 1, 1961

By Michael G. Pojar

This Bureau of Mines report estimates the population of the principal types of machinery in use by the coal mining industry during 1982 in surface and underground mines. Estimates were arrived at using 1976 coal equipment population estimates as baseline data with modifications made for new mine development, expansion, and closure occurring during 1976-82. Estimates were broken down into 3 regions which included all 26 coal-producing States. Modifications made to the baseline data were computed using (1) actual equipment information when available, plus (2) equipment information hypothesized from representative generic mine models, which were predicated on mine size and mine method. Roughly half of the equipment fleet at new or expanding coal operations was known; the remainder was hypothesized. The mine models used to generate equipment information are included in this report, along with the hypothesized equipment use data. The equations and various factors used to determine the equipment adjustments for mine closings, new mine openings, and small coal mine operations are also identified.

Jan 1, 1986

By Steven D. Scott

Several polymetallic sulfide deposits (copper, zinc, f lead, silver, f gold) presently exposed at the surface of the ocean floor are of sufficient size and apparent grade that they will someday be seriously considered as mineable resources. Responsible ocean mining may have some real environmental advantages over land mining, although they both share the same downstream problems caused by smelting and refining. The area of disturbance for an ocean mine would be much less than for an equivalent sized deposit on land around which considerable rock has to be excavated in order to get at the ore. Acid mine drainage, a very serious problem in land ming, would not be a concern in the alkaline and oxygen deficient environment of the deep ocean. There would undoubtedly be loss of habitat for some marine organisms but this could be minimized by mining deposits that are no longer hydrothermally active and therefore support little life. The risk of severe corrosion and thermal damage to the mining equipment at hydrothermally active sites would probably preclude their recovery in any event. The scientific community and environmental advocates should take advantage of the long lead time before ocean mining commences to insure that the environmental mistakes of the past, as encountered in some land mining, are not repeated. In order to fully understand and thereby mitigate the consequences of recovering seafloor sulfides, test mining of a small deposit using the German-designed high capacity television grab, preceded and followed by detailed observations of the mining site from a submersible, is proposed.

Jan 1, 1992

The Longwall Strata Control and Maintenance System (LoSCoMS) is designed to monitor shield pressures in real-time from longwall faces and to provide on-line information related to underground strata behavior and longwall mining operation. The information includes shield pressure data with statistical analysis of setting, developing and final pressures, prediction of shield pressures for the following shift or day, etc. and maintenance data on the shields. The LoSCoMS has been installed and tested at Shoal Creek Mine operated by Drummond Company, Inc. The system is providing valuable information to mine operators for better understanding of underground behaviors. As a result, it has become an effective tool for minimizing ground control hazards and reducing out of seam material.

Jan 1, 1997

By R. B. Haagensen, E. Martinez, V. Kudryk

The sample under investigation contained approximately 16% BaSO, and was 80% -325 mesh. Established methods for floating barite did not produce concentrates of satisfactory grade or barite recovery because of low barite content and the presence of 6% calcite in the feed. By using a new long-chain sulfosuccinamate collector in combination with relatively high concentrations of sodium silicate, a barite concentrate was produced that would be acceptable as an oil-drilling mud using a simple rougher-cleaner circuit. No desliming of the fine-ground feed was necessary. Barite recovery was over 80% and the concentrate produced had a specific gravity higher than 4.3. During the course of the investigation, a procedure was developed to obtain semiquantitative determinations of barite, calcite, quartz, and feldspar in test samples using an infrared spectrophotometer. Samples were also analyzed in a thermobalance for determination of the calcite content. The use of these instruments made it possible to obtain quick mineralogical assays and proved to be of invaluable assistance in guiding the flotation testing.

Jan 1, 1976

By R. M. Santmyers

Caesium, rubidium, and lithium are sometimes described as the minor or rarer alkali metals. They generally occur together in nature, although, lithium is distributed more widely and is far more abundant than either of the other two. The chemical, and even the physical, properties of these three elements can best be considered In conjunction with the more familiar members of the alkali group, sodium and potassium. The five elements lithium, sodium, potassium, rubidium, and caesium show an interesting gradation properties from member to member with the increase in atomic weights. All are silvery white and soft enough to be cut with a knife. They tarnish rapidly in air and decompose water at ordinary temperatures. The lowest temperature at which the action of the several metals on water can be de¬tected is -98°C. for sodium, -105°C, for potassium, 108°C. for rubidium, and -116°C. for caesium. The chemical activity appears to increase steadily from

Jan 1, 1930

By S. Epstein

THE new low-alloy high-strength steels are obviously here to stay. With 75 per cent higher yield strength and 50 per cent higher tensile strength than plain carbon structural steel, they permit 20 to 40 per cent weight savings and 10 per cent or more increase in pay load in the con-struction of railroad cars, buses, trucks, and a great variety of material-handling equipment. Their cost is low enough so that the extra cost of the new lighter construction over that with carbon steel offers an attrac-tive self-liquidating investment; in some instances new construction with these low-alloy steels may even be as cheap as with plain carbon steel. A considerable and rapidly growing demand for the low-alloy steels has already sprung up. The many steel compositions that have appeared on the market lately 18,27,28,29,30 to meet this demand would seem to indicate that no single composition is uniquely fitted for the purpose. However, no doubt some compositions are more suitable than others. The purpose of this study was, therefore, to compare the effects of the various alloying elements that might be used in the low-alloy steels in order to choose the metallurgically most logical composition, paying due regard, of course, to the economic aspects involved.

Jan 1, 1936

By Barry Silverman

As a significant mineral supplier, consumer of primary fuels, and producer of wastes and emissions to air, water, and land, the domestic copper industry through its investment and operating decisions influences the nation's economy and the environment. In turn, the copper industries' decisions are influenced by various factors: government energy and environmental policies, economic conditions, and technological considerations. The authors have developed a framework for assessing in an integrated manner the impact of these factors on the future investment and operating decisions made by copper firms. Specifically, this model is designed to capture the technology forcing nature of regulatory constraints, the differential situation of individual copper deposits and plant locations, and the price of factor inputs and conditions in the nation's economy. The capability to do this has only become real because of the decision of the U.S. Bureau of Mines to create Mineral Availability system1 or MAS. This system contains detailed but confidential information about each mine and mill in each of 35 mineral industries." Without MAS or a similar information system, the utilization of the methodology we offer would be impractical, but with. MAS it offers a unique technique of dealing with environmental-resources policy questions.

Jan 1, 1979

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By Azin Zangooi, Cesar Gomez, James Finch

Frother concentration is a variable which significantly affects the flotation performance by decreasing bubble size and helping froth stabilization. Variations in frother concentration, which mostly go unnoticed in industrial operations, may affect these functions. Some factors that can cause variations include the fact that frothers are normally dosed based on feed tonnage and not solution concentration, unstable frother delivery, incomplete dissolution for low solubility frothers, addition of frother-free wash water, remnant frother in recycle waters and frother partitioning to the froth. A colorimetric technique developed for determining frother concentration on site makes it possible to detect the occurrence of these problems and to establish their magnitude, allowing conditions to be adjusted to reduce frother concentration variations. By sampling and analysis, frother distribution throughout a circuit can be established, referred to as ‘frother distribution mapping’. Experiences at several concentrators processing sulphide ores are used to illustrate time restrictions for sample analysis, and to demonstrate temporal and spatial frother concentration changes as a consequence of variations in the grinding stage, recycled waters containing frother, and frother partitioning.

Jan 1, 2014

By P. B. Leavenworth, Jack F. Harang

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company's No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation's No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company's No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942

By W. H. Bassett

IN the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-min.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage. 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystallization of cold-worked alpha brass on annealing,1 Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work.

Jan 1, 1919

By Mary Jean Buchanan

The last twenty years have seen the advent of environmental concerns and sustainable development, and the industry has witnessed the rise of Environmental Management Systems and their registration through several international standardization systems such as EMAS and ISO 14001. Beyond EMS and ISO 14001, which new goal the mining industry should aim at. Life-cycle assessment (LCA), another tool from the Environmental Management System series, is also on the rise and currently the object of an international standard (ISO 14040:1997). Through LCA, it is possible to assess the environmental aspects and potential impacts associated with products and services, taking into account all the activities required for its fabrication, its use, its transportation and its disposal. How could LCA be applied to the mining industry ? Is the international market pressurizing on mining companies to supply an ?environmental ore?? What about the automobile industry and its use of LCA ? Will it influence the ferrous and non-ferrous metal industry, suppliers of raw materials ? This paper presents a review of possible applications of LCA for the mining industry as well as world trends.

May 1, 2001

AT THE beginning of May the German government offered to the French and Belgians the payment of 30 billion .gold marks as indemnity, accom-panied by rather involved terms, among which was the ability of the Germans to finance the foreign loan. This offer was promptly and summarily refused by the French and Belgians. Since then there have been more palavers between the two parties, while the occupation of the Ruhr continued without especial incident, except some socialist riots and workmen's strikes. The renewed conference between the Allies and the Turks at Lausanne continued, without apparently getting anywhere. The Turks demanded an indemnity from the Greeks, which the latter refused to pay, threatening a resumption of hostilities rather than to do so. A. Bonar Law, the British premier, resigned his office soon after the middle of May, owing to poor health. The King appointed Stanley Baldwin as his successor. This. Attainment to the premiership of Great Britain by a business man is a noteworthy event. It is, moreover, to be remarked that Mr. Baldwin is personally acquainted with America and is well known to be a friend to Americans. The Irish rebellion came to an end. Economically there was some improvement in the situation in Great Britain during May, which was reflected in diminution in the number of unemployed. Nevertheless the aggregate of the unemployed in Great Britain continues at a very high figure. In Germany there has been an increase in the number of unemployed ever since the French occupation of the Ruhr, which naturally has been choking German industry. Previous to this the percentage of unemploy-ment among German workers had been low ever since the Armistice. A noteworthy domestic event was the non-stop flight of an airplane, May 2-3, bearing two aviators from New York to San Diego, California, in about 27 hours.

Jan 5, 1923