Search Documents

By D. Yeager

Researchers at the U.S. Bureau of Mines have successfully used a genetic algorithm to tune computer models of three column flotation units simulating a separation circuit. The computer models rely on empirical constants that are selected so that the models accurately predict the performance characteristics of individual column flotation units. Unfortunately, these empirical constants have traditionally been selected using a time consuming trial and error process. A new and more efficient approach to selecting empirical constants for computer models has been developed. A genetic algorithm has been used to select the empirical constants for column flotation models used to simulate a three column circuit. Genetic algorithms are search algorithms based on the mechanics of natural genetics. They rapidly locate near optimum solutions in difficult search spaces. Bureau researchers have used these innovative search algorithms to dramatically reduce the time needed to select empirical constants for column flotation models. The approach is applicable to the selection of empirical constants for numerous other computer models.

Jan 1, 1995

By Rogers M, Sullivan B

Golden Crown Mine is a narrow vein gold mine producing 75000 tpa. Production has been predominantly by shrink stoping using hand held machine and airleg. Bogging from these stopes is done with Toro 150 LHD units.Previously the standard development method consisted of developing a sill drive, a footwall drive and millholes every 7 m. This meant that for every metre of ore development, 2 m of waste development was required.

Jan 1, 1993

By Sam S. Taylor

Disposal of brines produced with crude petroleum and natural gas is a continually increasing problem. The necessity for studying this problem has been realized more generally in recent years, and in August 1934 an agreement was made between the Kansas State Board of Health and the United States Bureau of Mines to conduct a cooperative technical study of methods of brine disposal. To date one paper in the technical press4/ and three reports5/6/ 7/ have been published in which are given results of studies carried on under this cooperative agreement. In the Mid-Continent fields, the methods used most generally for handling oil-field brines are: (1) Impounding in evaporation ponds; (2) controlled diversion into surface streams; and (3) injection into subsurface formations through wells assigned for this purpose. Various States recognize one or more of the methods as legally authorized procedure. Impounding brine in ponds and solar evaporation have proved inadequate as a general rule, owing, usually, to the porous nature of the soil, the low rate of evaporation, or both. Diversion of

Jan 1, 1937

By W. Dan Walker

In an effort to keep mine hoist accidents to a minimum and to impart to managers and workers the essential elements that enter into safe installation and maintenance of hoisting equipment, the Bureau of Mines presents this Information Circular as a guide. Hoisting of men and materials is an essential operation in many mines and has become so commonplace that some persons are likely to ignore day-to-day inspections or become lax in the operating phases. With proper maintenance and operation, hoists can be exceptionally safe. However, lack of strict attention can invite tragedy or costly shutdowns.

Jan 1, 1961

By Z. S. Abisheva

The Zhezkazgan copper sulfide ore deposit in Kazakhstan contains both rhenium and the rare osmium isotope "osmium-187" (187Os) in the high isotopic purity of 99.4 ± 0.2%. This isotope is believed to have originated as a result of the disintegration of one of the rhenium isotopes, according to the reaction: 187Re75 ?> 1870576 + B- + v~ (where B is a 13-particle, v~ is a 3-disintegration antineutrino). The distribution of osmium and rhenium in metallurgical byproducts produced during the recovery of copper from these ores has been studied and process flowsheets for the processing of rhenium and osmium-containing byproducts have been developed.

Jan 1, 2007

By T. A. Sullivan

The processing of sweated aluminum electronic scrap was investigated to develop methods for recovering the aluminum and concentrating the other metals, including copper, lead, gold, and silver, into a product that can be separated by known methods. Two molten-salt electrorefining processes were developed and tested. The first process utilized a three-layer refining cell with a BaCI2-NaF-AIF3 electrolyte, which operated at 750° to 850° C. The second process used an all-chloride electrolyte of NaCI-KCI-AICI3 at 750° to 800° C, with separate anode and cathode compartments. High-quality aluminum was recovered that averaged 99.8-percent pure in the three-layer cell and 99.6-percent pure in the compartment cell. Over 94 percent of the aluminum was recovered with cathode current efficiencies of approximately 90 percent in both methods. The copper, lead, tin, silver, gold, and other metals were concentrated threefold in an anode product. Separation of lead and part of the tin by liquation from this product seemed feasible. The anode product was smelted to prepare a 96-percent copper bullion that contained 690 ounces of silver and 65 ounces of gold per ton, with 98 percent recovery of these values.

Jan 1, 1972

By Per-Martin Sandgren, Alrik Anttila

LKAB's ores have specific mineralogical properties that make them especially suitable for the production of supergrade concentrates. Conditions are particularly good for this purpose at Malmberget, where a concentrate for high-purity sponge iron production has been produced for many years. This product assays approximately 71.5% Fe and 0.20% SiO2. Potential exists for still further improvement. In recent years, the production of fractioned concentrates has been started. The material lies within the size range 74-125 µm and the approximate chemical analysis is 71.4% Fe and 0.30% SiO2. Other special products are under discussion. Malmberget ores are also suitable for the production of high- purity direct reduction pellets with a SiO2 content below 1%.

Jan 1, 1983

By S. Koppalkar

ABSTRACT: The development and evolution of the gravity recoverable gold (GrG) test procedure at McGill university is reviewed in this paper. Since the late 1980s, the research group led by the late Professor André Robert Laplante at McGill university has undertaken fundamental studies and applied research of the Knelson concentrator to develop a sustainable method of estimating GrG. Historically, a concept of “free gold” was used, and it was de?ned as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, the practical use of amalgamation has declined. around 1994, a methodology using a 3-in Knelson concentrator to measure gravity recoverable gold was established at McGill university. as a result of more than 10 years of improvement and optimization, this technique has become a standard method of evaluating GrG for gold ores, gold plant streams and platinum group metals. By 2006, about 200 GrG tests were carried out at McGill universityon ores from all over the world. recently, a modi?ed version of the GrG test (a simpli?ed test) was developed to provide a quick and rough estimate of the GrG in a sample; this simpli?ed test has theadvantage of reduced mass, processing time and cost. to recognize and honour the contributions madeby the late Professor Laplante towards the establishment of a standard test procedure for assessing gravity recovery potential, the authors propose that the GrG test be named after Laplante.

Jan 1, 2010

By Marlin J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in nonmetallic mining with limited financial risk-if properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations. Risk of capital is determined by weighing all factors that should be considered and how well judgments are based on information acquired. It is a simple, true axiom of business that an investment must be founded on amount of capital required with its expected return plus profit, expertise required to operate, and time involved. Urban quarries generally offer excellent stone product market opportunities. Costs of land with mineral containment and processing operations are much greater than in rural areas. Environmental problems have become increasingly severe. Competition from other quarries in the market area is usually directly proportional to the profit attractiveness. Risk of capital (initial, developmental and operational) can be evaluated and reduced only by thorough analysis of the entire situation. Time and money expended on planning and preliminary investigations probably represent the most productive investment of available company resources. Basic Reasons to Establish a Limestone Quarry Profit Motive: Certainly the dominant and overriding motive must be that of attaining a reasonable profit. In certain situations a quarry firm may acquire land, necessary rezoning (if required), and satisfy all of the other prerequisites preparatory to beginning operations but delaying the actual development.

Jan 1, 1980

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

By W. J. Schlitt

The Namibian Copper Joint Venture has been formed to undertake development of the Haib copper deposit, one of the largest undeveloped copper resources in Africa. The development programme includes extensive hydrometallurgical testwork that is being managed by Kvaerner Metals (formerly Davy International).Various parts of the programme have been contracted to four third-party laboratories. The testwork involves sample selection and characterization, amenability tests, and a parametric study on the leaching variables. All portions of the programme are described and the results a represented. The ores selected for testing are quartz feldspar porphyries. The amenability tests include ?mapping? studies to assess optimum leach conditions, tests at high oxidation potentials, oxidation with various bacterial strains, and heap leach modelling. The parametric programme includes such variables as ore grade, leach temperature, crush size, pH, and ferric iron content of the lixiviant. Testing was done on both whole ore and concentrate. Results show that bacterial leaching is effective and that ore grade and temperature are key variables. Crush size and pH have less impact on copper extraction. For mid-grade ore, about 0.25 per cent copper, extraction is projected to reach 50 per cent after two years when heap leaching tertiary crushed ore at 60°C and pH 1.5. The heap leach operation would fit well with the proposed roast-leach operation used to treat higher grade ores. The latter could supply the low cost heat and acid needed in the heap leach.

Jan 1, 1999

By Robert A. Bauer

Two basic types of subsidence occur in Illinois: pit and sag / trough. Pits develop over mines less than 165 feet deep and where relatively incompetent strata are found over the mines. Sag subsidence is found over mines as shallow as 75 feet and more generally over mines of greater depths. The percentage of subsidence and angles of draw associated with sag subsidence appear to be controlled by the rock properties at each specific site. The percentage of subsidence and angles of draw are smaller where the sites are not affected by geologic structures. An investigation to determine if a time factor based on the time interval from the date of mining to the subsidence events has shown that simple correlations with time, percent extraction, average pillar stresses, and pillar dimensions is not evident in Illinois.

Jan 1, 1982

By Ronald D. Hill, Elmore C. Grim

Sediment is one of America's greatest pollutants. More than a billion tons of sediment reach the major streams of the United States annually(l). Damages are reflected in the reduced carrying capacity of streams, clogged reservoirs, destroyed habitat for fish and other aquatic life, filled navigation channels, increased flood crests, degraded facilities for water-based recreation, increased industrial and domestic water treatment costs, premature aging of lakes by enrichment of the water with silt-carried fertilizer that promotes algae growth, destroy crops, and reduce productivity of flood plain soils. Erosion and sedimentation are natural processes that are usually gentle actions releasing controlled amounts of silt from watersheds to receiving streams. Surface mining activities accelerate these natural processes and short duration, high intensity storms can become a violent force moving thousands of tons of soil in a brief period of time. Cover is a very important factor. With the removal of ground cover, water moves across the denuded area on its own terms picking up soil particles as it flows and leaving gullies behind. The susceptibility of strip-mined land to erosion depends on: 1.Physical characteristics of the overburden 2. Degree of slope 3. Length of slope 4. Climate 5. Amount and rate of rainfall 6. Type and percent of vegetative ground cover. By development of erosion and sedimentation control plans before disturbance of the area, many of the detrimental effects of strip mining can be prevented.

Jan 1, 1974

By S. Kado, G. Derge, L. Yang

Self-diffusion coefficients of silver in molten silver have been measured by means of the capillary-reservoir method in the temperature range 1002" to 1105°C. The results can be .represented by the equation D = (7.10 i 0.06) X 10-4 exp [(—8150 ± 1130)/RT]. The heat of activation agrees within the limit of experimental uncertainty with that for the viscous flow. The validity of the Eyring and the Stokes-Einstein equations are examined on the basis of the self-diffusion coefficients obtained and the known viscosity data of molten silver. MEASUREMENT of the self-diffusion coefficient of silver in molten silver was made in the temperature range 1275° to 1378°K, using the capillary-reservoir method and &"' as the radioactive tracer. The experimental arrangement is shown in Fig. 1. Silver of 99.99 pct purity (fine silver), was melted and degassed in vacuum in a graphite crucible situated inside a McDanel vacuum jacket. The crucible (4 in. tall and 1 in. ID) was protected both at the top and at the bottom with graphite shields and contained about 220 g of silver. The sample holder was a piece of graphite rod (1 in. long and 1/2 in. diam) with 4 capillaries drilled longitudinally into it. The holder was screwed onto a long graphite rod (12 in. long and 74 in. diam) which was connected to a steel disk hanging on a nylon string through a glass pulley. The steel disk kept the sample holder at the center of the McDanel tube and was heavy enough to overcome the buoyancy when the holder was lowered into the molten silver. By turning a handle connected to the pulley through a tapered glass joint, it was possible to raise or lower the sample holder without breaking the vacuum. Two such arrangements were constructed, sitting side by side in 2 Kanthal furnaces. One with non-radioactive silver in its crucible was used for the diffusion run and the other with radioactive silver in its crucible was used for filling the capillaries. To fill the capillaries with radioactive silver, the sample holder was degassed first and then lowered into the radioactive molten silver in vacuum. Purified argon gas was then admitted into the system to push the liquid silver into the capillaries. After cooling in argon, the filled capillaries were polished on emery paper to expose the top of the rod and used immediately as samples for the diffusion run which was carried out at the same temperature as that used for filling the capillaries. During the diffusion run, the samples were degassed in vacuum and lowered slowly into the nonradioactive molten silver before purified argon was admitted into the system. After a predetermined period of time, the samples were raised out of the melt and cooled in argon. The temperature of the melt was measured before and after the run with a chromel-alumel thermocouple inside a McDanel protection tube. Another chromel-alumel thermocouple attached to the outside wall of the McDanel vacuum jacket was used to indicate any fluctuation in the temperature of the furnace during the run, which was found to be less than ± 2°C for the longest run made (93 min). The temperature gradient inside the molten silver was found to be negligible. No significant difference was observed in the results obtained whether the melt was stagnant during the run or was stirred by raising and lowering the sample holder slowly a few times a minute for a distance of about 1/4 in. inside the melt.

Jan 1, 1959

By H. P. Reid

Portland cement is manufactured under either of two general processes, the wet or the dry. The raw materials in general consist of limestone, shells, marl, cement rock, clay, shale, blast-furnace slag, etc., so proportioned that when calcined the desired composition will be obtained. In the wet process the combined raw materials are ground to extreme fineness in the presence of water, to a resulting slurry of from 30 to 50 per cent moisture content. The moisture of the slurry may be reduced by thickening or filtering processes for feed to the cement kiln or the slurry may be fed to the kiln with its full percentage of water. The dry process differs from the wet in that the surface moisture of the raw materials is removed prior to grinding. For the drying of these materials heat is required and in most cases is produced by burning of raw fuel either on grates or stokers before the dryers or in suspension in the form of pulverized coal, oil or gaseous fuel. The power required for making the cement is sometimes purchased from outside sources; sometimes it is generated from the heat in the waste gases leaving the cement kilns, or generated at the plants direct from raw fuel. We have, then, as the possible requirements of fuel in the cement industry: (1) fuel for power generation, (2) fuel for drying raw materials, including coal before pulverizing, and (3) fuel for burning the raw materials to cement clinker. There is no essential difference in quality required in fuel for burning the materials by the wet and,dry processes. Fuel fob Power Generation As there is nothing peculiar to steam generation in a cement mill power plant as compared with other power plants this use classification of such fuel will be found in other reports of the Technical Committee. Fuel for Drying Raw Materials and Coal Any fuels capable of producing moderate temperature gases may be used for drying raw materials. There is no problem of material contamination from fuels at this part of the cement manufacture to be guarded against.

Jan 1, 1932

By V. D. del Valle, T. G. Joseph, J. J. Berezan

Aggressive driving patterns, rough and poorly maintained roads and pit floors, along with the occasional bump and poorly placed load from a shovel can create intense and sometimes serious vibration levels on a heavy hauler. The effects of high vibration have been shown to be of concern for the health of the operator as well as the reliability of the equipment. It is proposed that an onboard vibration warning system based on the ISO 2631-1 standard could be used to help operators reduce the vibration levels experienced in a heavy hauler. The onboard system would consist of a screen that displays the instantaneous vibration in the form of three lights: green (safe zone), yellow (cautious zone), and red (danger zone), as well as an overall vibration exposure or dose for the entire shift. With the utilization of the warning system, it is anticipated that the overall vibration levels will be decreased resulting in improved operator health, a reduction of vibration-induced maintenance, and improved haul roads through reduced impact loading and repair for localized trouble areas.

Jan 1, 2004

By E. C. Skinner

As the program says -we'll he talking about the expectations of the Management of an Industrial Mineral enterprise relative to the activities of geologists engaged in that enterprise. Industrial Minerals is such a large industry both in tons produced and in value of product -and of such diversity and complexity of participating enterprises, minerals and products that I doubt if anyone person can speak for the entire industry as to the expectations of management with respect to the geologist. I'm sure there are major differences in emphasis between segments of management as to the relative importance of the different aspects of the geologists' role in the scheme of things. However, we will try to generalize concerning what we consider to be important factors and to be more specific perhaps of some of the factors with which we have had direct assessable experience.

Jan 1, 1972

Today's largest producer of domestic beryllium oxide, Mineral Concentrates & Chemical Co., Inc., has recently disclosed the basic outline of its unique process of beneficiating beryllium ores to high purity BeO. This process, known as the Mincon process, is a thermic-flotation scheme which has reportedly resulted in a recovery ratio exceeding 90% and in allowing up-grading of beryllium concentrates to as high as 33%. Mincon borrowed a step from the iron ore industry by introducing a pelletizing and sintering stage in their flow sheet at the company's mill at Loveland, Colo. This mill, now operating at full-capacity with three-shifts a day, is still undergoing some minor changes and adjustments in the equipment and chemical reagents.

Jan 10, 1961

By W. C. Weslow

AN extended program devoted to the development of a matrix for holding diamonds of a size and. kind not heretofore generally used is being carried on by the Carboloy Company, and this paper describes the part of the development that affects mining and its allied industries. Labora-tory and field work so far has indicated the following: 1. Tungsten carbide and cobalt form the most desirable known matrix material for the holding of diamonds for drilling work. 2. Industrial bort diamonds in sizes and of a class not generally heretofore acceptable and therefore less expensive can be successfully held in this cemented carbide matrix. 3. In exploratory drilling, the combination of bort diamonds, impreg-nated throughout a matrix of tungsten carbide and cobalt, when fabri-cated onto drilling crowns, is an indicated economic substitute for drilling crowns in which the diamonds are set by hand, mechanically or by casting. 4. This impregnated type of drilling crown or bit has definite possi-bilites of revolutionizing the drilling of blast holes, particularly in the harder formations. This will be brought about by the development of high-speed light-weight rotary equipment using an impregnated diamond bit to replace the percussion drill now in general use. (The development of this rotary equipment is well past the laboratory stage at this time.) 5. That the use of a rotary bit is a preventive measure in the fight against silicosis. The development of this product was started by G. F. Taylor at the Research Laboratories of the General Electric Co. It was early recog-nized that it had possibilities in the drilling field and the present product is the result of considerable experimental work with other powdered metals as well as with tungsten carbide and cobalt.

Jan 1, 1940

By S Hancock, B H. Brady, H Muhlhaus

The aims of this paper are to present the governing science, verify the performance and demonstrate the potential engineering applications of a computational simulator for in situ leach mining of non-ferrous minerals. Assuming that the target mineral is deposited either uniformly within rock matrixes (matrix-hosted) or on fracture walls (fracture-hosted), in situ leaching can be treated as reactive flow and transport in geological media (porous media for matrix-hosted ore deposits and fractured media for fracture-hosted ore deposits). Under this treatment, the processes of in situ leach mining for non-ferrous minerals can be quantified through several sets of equations and these coupled equations have been numerically solved. The computational simulator has been applied to the simulations of one-, two-, and three-dimensional in situ leaching cases. The computational simulator, together with laboratory and in situ leaching tests, can be used to:optimise the leaching chemistry; optimise the in situ scale mining operations; scale up the in situ scale test operation to a full-scale mining operation; and evaluate the post-mining environmental restoration plan.

Jan 1, 2000