Search Documents

By Narasimhan K. S, Sastri S. R

A typical high silica low grade magnesite from the Salem area of Southern India, was used in studies to develop a suitable flotation system involving commercially inexpensive sodium oleate as the collector together with other reagents which can give a product of the required grade with an acceptable recovery. It was found that the presence of metallic ions such as Cu+, Fe+++ or Ca++ introduced by the addition of their salts, or by their formation with the addition of hydrochloric acid to react with magnesium and calcium carbonate in the me, can act as effective depressants for silica. The addition of 'hydrochloric acid' was found to give best results.

Jan 1, 1980

By Deon van Tonder, Chuck Edwards

"Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares some of these options on the basis of typical capital and operating costs for both the solvent extraction circuit and downstream uranium processing, and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.INTRODUCTIONIn the 1950s the uranium industry was the first industry to adopt solvent extraction (SX). Since then, the flow sheets have advanced. Notable was the introduction of tertiary amine extractants by General Mills during the late 1950s and 1960s (Mackenzie, 1997; Mackenzie, 2005), which is still today considered ‘state of the art’ technology. Initially solvent extraction was done in combination with ion-exchange, such as in the Eluex flow sheet, followed later by the adoption of direct solvent extraction from pregnant leach solution (PLS). From a strip-precipitation perspective ammonia strip followed by ammonium diuranate precipitation was widely adopted as the norm in the uranium industry. More recently alternative strip systems have been receiving increasing attention due to the environmental, health and safety issues associated with ammonia and the resulting calcined uranium oxide product. This paper explores some of these alternative options in comparison with the ammonia route.It is important to acknowledge that each operation is unique, and therefore the information and philosophy outlined in this paper serve to provide a general guide that can be potentially applied and adapted to any site or project."

Jan 1, 2013

The following list comprises the names of those persons who became members during the period Sept. 10, 1919, to Oct. 10, 1919. ADAMS, R. L Chief Min. Engr., Old Ben Coal Corpn., Mine 12, Christopher, Ill. Arizumi, Hiroshi The Kuhara Min. Co., Ltd., Tokyo, Japan. BAILY, T. F Pres. & Gen'l Mgr., Electric Furnace Co., Alliance, 0. BALDWIN, A. J., Min. Engr Box 145, Pikeville, Kentucky. BALTZELL, WILL H., Chief Engr., Canadian Steel Corpn., Ltd., Ojibway, Essex Co., Ont., Canada. BANON, E. MAGAWLY, Examining Engr., Dawes Bros., Inc. 108 So. LaSalle St., Chicago, Ill. BARNES, W., Mech. Engr., Excavating Dept., Ruston & Hornsby, Ltd., Lincoln, England. BASHORE, E. GORGAS, Head Chem., The Babcock & Wilcox Co., Bayonne, N. J. BASS, A. L Supt., Hobson Silver Lead Co., Ltd., Ymir, B. C., Canada. BORN, SIDNEY, Chief Chem., Empire Gas & Fuel Co. & Associated Companies, 1100 Cherokee Ave., Bartlesville, Okla. BRADLEY, J. G,, Coal Operator, Pres.,& Gen'l Mgr., Elk River Coal & Lumber Co., Dundon, W. Va. BENNETT, G. W., Min. Engr., Sales Engr., Taylor-Wharton Iron &- Steel Co., High Bridge,. N. J. BRUFF, CHARLES E., Member firm Bradley, Bruff & Labarthe, 85 Second St., San Francisco, Cal. COLLINS, FRANK W., Chief Engr., Bradley, Bruff & Labarthe, 85 Second St., San Francisco, Cal. CONNELL, F. M., Min. Engr., Eastern Alin. & Mill. Co., Ltd., 905 Bank of Hamilton Bldg., Toronto, Ont., Canada. CooK, HARRY H., Vice-pres., Valley Mould & Iron Corgn., 137 Shenango St., Sharpsville, Pa.

Jan 11, 1919

By G. F. Friel, J. C. Edwards

A series of seven underground-coal-mine fire experiments was conducted in the Safety Re-search Coal Mine at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory. Coal and styrene-butadiene-rubber conveyor belting were burned upwind of two sensor stations, 18 m and 148 m from the fire source. Exhaust from a diesel locomotive flowed over the fire sources in six of the tests. Metal-oxide-semiconductor (MOS), CO, and optical-path-smoke sensors were positioned at both stations and found to be an optimum set of sensors for the fire discriminations. A representative set of 7,679 samples of CO data and data from the smoke and diesel-exhaust MOS sensors were used as inputs to train a neural network (NN). By testing 42,538 data samples from the seven experiments, all fires were detected by the NN within 9.67 min from the onset of significant changes in the MOS voltages without any false alarms.

By John M. Karhnak

The Bureau of Mines has a long history of research in Ground Control. For many years, this work was done at Bureau facilities by Bureau researchers. As the tiles changed, however, the area of research interest broadened, and additional methods of implementation, such as con- tracts, were added. 'Ibis paper outlines the organization, goals, and methods of implementation of the Bureau Ground Control Program, along with procedures for project selection. This program organization is followed by several specific examples of Bureau research that will be soon ready for use in the mines.

Jan 1, 1981

By L. O. Souza, J. F. Gewher, M. P. Scussiatto, C. S. Mendonca, R. A. McClure, B. T. Kuckartz, J. Kloeckner

Blasting is the most effective and economical tool available to fragment and move rock for most applications. If properly executed, it can improve down-stream operations such as loading, hauling and crushing. It is not possible, however, to have full control over the energy released by the explosives when a poorly designed blast pattern is used. A poorly designed blast can produce serious damage to equipment and create a potentially hazardous condition to people. Advanced mining technology has been developed to address these potential hazards and optimize the blast pattern. This profiling technology can assist with blast planning and provide quick, precise data about the condition of the rock structure to be blasted. The 3G BlastMetrix system presented here uses three-dimensional (3D) stereo photogrammetry to model the rock mass in a fast, practical and safe manner. Through the image overlapping method, a 3D model is created with thousands of points that provide a significant amount of data regarding geology, geometry and topography conditions. The blasting plan can then be made in a way to optimize the rock fragmentation and avoid areas that could create flyrock. This paper is a case study concerning usage of stereo photogrammic surveying and borehole survey systems in a blasting operation at the Brazilian Quarry, Incopel. One 3D image of a drilled bench was generated using photogrammetry survey technology and the borehole survey data collected using the rodded Boretrak borehole survey system. Utilizing the minimum burden profile reports, explosive loading could be done accurately, resulting in an optimized blast with good heave and fragmentation as well as increased safety.

Jan 1, 2013

By Louis Cabot

A pilot plant of the Modular Gold Processing Unit (MGPU) was designed, installed and operated, over a 8 months period, by RSW-Béroma, at the Granada Mine located near Rouyn-Noranda, Quebec. A description of the project geology, plant set up as well as exploitation results, including productivity and profitability curves, are given for a small scale mining operation in comparison with larger ones. Copyright ã 2001 CIM

May 1, 2001

By T. C. Vogt

The past history of uranium production has been dominated by strip and shaft mining methods, but recently in-situ leaching has emerged as a viable alternative for uranium recovery. (1-8) Mobil was the first company to start in-situ uranium leaching in New Mexico. Mobil's Crownpoint project areas are in Mdinley County and are part of the Grants Mineral Belt. The major uranium deposits in this area occur in the Westwater Canyon Member of the Jurassic Morrison Formation. (9-11) The ore depth at the Crownpoint project is about 2000 ft. In an earlier paper we discussed the uranium mineralogy of an areally broad sampling of Crown- point ore. (12) The organic carbonaceous material often associated with the coffinite ore was characterized in some detail. The organic material appeared to be a very mature, coaly-type kerogen derived from plant components. This result was consistent with other studies on such carbonaceous material. (13-15)

Jan 1, 1981

By P. Coleman, J. C. Kerkering, S. Iverson

A fatal accident may result when a dozer is driven over a hidden void in a coal surge pile and the dozer falls into the void, burying and suffocating the dozer operator. This type of accident was analyzed by researchers from the Spokane Research Laboratory of the National Institute for Occupational Safely and Health using inexpensive fault-tree programs that had been developed, for use on a personal computer. Fault-tree analysis is a systematic safety-analysis tool that proceeds deductively from the occurrence of an accident event to the identification of the root causes of that event. The analysis identified basic and intermediate events that led to the burial of the dozer and graphically depicted the interrelationship between the basic events as well as the intermediate events leading up to the accident. A sensitivity analysis on assigned probabilities showed which events had the greatest influence on dozer burial in a coal surge pile. Operational guidelines and engineering controls are suggested to decrease the probability of a burial event.

Jan 1, 2002

Jan 1, 1967

By V. Ramirez, M. Mankosa, G. Luttrell, E. Wasmund

"The performance of column flotation is strongly influenced by the effectiveness of the gas sparging system. Unfortunately, field studies suggest that gas injector systems used for column sparging are not always optimized. This unfavorable condition can create a number of issues within the concentrator including lower recoveries, poorer metallurgical upgrading, decreased capacities, increased circulating loads, higher reagent consumption and inefficient energy usage. To help overcome these problems, techniques have been developed that can be adopted by plant operators to improve sparger performance. These techniques include (i) design modifications to sparger components such as nozzles, distributors and internal parts and (ii) operational improvements such as proper balancing of gas/water flows, elimination of unnecessary pressure drops, and staged injection of frothing agents. This article reviews the important criteria that govern sparger operation and provides data showing how simple low-cost improvements can positively impact column performance. INTRODUCTION Column flotation cells have become the most popular machine design for industrial applications that require high purity concentrates. The superior metallurgical performance of column cells can be largely attributed to their unique geometry, which readily accommodates the use of froth washing systems. The wash water minimizes the nonselective entrainment of ultrafine gangue minerals that would otherwise be hydraulically carried in the water reporting to the froth concentrate. The larger height-to-diameter ratio of columns allows a deep froth to be maintained, which is essential to achieve even water distribution. Due to these unique features, column cells can provide impressive levels of metallurgical performance closely approaching the ultimate separation curve predicted using the flotation release analysis method (Kohmuench et al., 2007). Another very important feature of column cells is the design of the gas sparging system. One popular choice in the minerals processing industry is the Eriez SlamJet® sparger. As shown in Figure 1, this type of sparger operates by passing compressed gas through a small discharge nozzle. Fluid turbulence created by the exiting gas disperses and distributes small bubbles into the flotation pulp. The sparger is equipped with an internal moveable rod that is attached to a pressure diaphragm in the back housing of the sparger. The internal rod automatically moves back/forward and opens/closes the nozzle outlet when the compressed gas is switched on/off. This patented design effectively eliminates the accidental backflow of flotation pulp into the injection tube during shutdowns. The sparger can be operated as a gas-only injector or with the introduction of a small amount of high-pressure sparger water (Kohmuench et al., 2010)."

Jan 1, 2016

By Bradley Johnson

Introduction Since its creation in 1910, the Bureau of Mines has conducted a wide-ranging program of research on mining technology. Over the years, the Bureau has perhaps become best known for its accomplishments in mine health and safety technology, a field that has been the object of much public attention. Nevertheless, the Bureau's program in other areas of mining technology has always been strong and remains so today. A distinguishing feature of the current effort is its tendency to concentrate on high-risk, high-gain projects. Throughout the federal research establishment, the Administration's policy has been to phase out short-term research that could be performed by private industry, in favor of long-terms projects that industry cannot usually afford to fund. This tendency is evident in the following account of the highlights of the Bureau's current mining technology research program. Underground Mining Technology Fragmentation. Research studies on fragmentation have focused on nonexplosive concepts. If successfully developed, these concepts would lend themselves to continuous automated operation and reduce time and costs of fragmentation in underground mines. A special laboratory-scale device to investigate ripper cutting was designed and fabricated in 1982. Experiments were conducted with large drag cutters to develop an efficient cutting technique for hard rock. Tests were successfully conducted with 76- and 152-mm (3¬and 6-in.) bits in rocks up to 138-MPa (20,000-psi) compressive strength. Because of the success of these initial tests, larger-scale proof-of-concept tests are planned. To prepare for these tests, a tester capable of cutting a 1.8-m (6-ft) opening was fabricated. This device will allow ripper cutting to be carried out at full scale, and will also allow mucking and holddown requirements to be investigated. Preliminary estimates indicate that this concept has the potential to double excavation rates while reducing costs up to 30%. Mobile Hydraulic Monitor. A mobile hydraulic monitor system was designed, fabricated, and used to mine the St. Peter sandstone at an average rate of 22 t/h (25 stph) from a face in Martin-Marietta's foundry sand mine at Clayton, IA. A slurry transport system worked in tandem with jet cutting, resulting in a continuous mining and transport system. Problems with spray from the jet hitting the sandstone showed that a remote-controlled mobile monitor was needed at a station 15 m (50 ft) from the face, so the operator would have a clear view of the face and be safely out of the backwash. Crushers. Research on crushing systems to improve efficiency in underground mines is continuing. Final testing of a low-profile, portable crusher for underground applications has begun. A system for handling oversize feed to the crusher was conceived and tested. Underground crushing systems, portable enough to be kept near the face, offer considerable improvement in materials handling because main haulage by conveyor is often less costly. Hoists. Research to increase hoisting efficiency and speed and to reduce energy requirements has led to experimental ore skips. The skips feature guide rollers to improve riding characteristics, bearing improvement at critical locations, and weight savings of about 1.8 t (2 st). An experimental aluminum skip was installed last year at Kerr McGee's Church Rock mine. Performance is being monitored under production conditions. A portable service hoist for low-cost, efficient movement of men and supplies in raises between mine levels was designed, fabricated, and tested on the surface. The hoist has maximum equipment payload of 570 kg (1,250 lb) at

Jan 11, 1983

By S. M. Viduka

This paper presents a numerical investigation of solid separation in jigging device, which is a gravity separation method widely used in ore processing. Separation is recognized as being heavily dependent on fluid motion in the jig. This study explores the effects of the inlet time dependent velocity profile on jigging performance. Modelling of the liquid-solid system is performed through a combination of computational fluid dynamics (CFD) to simulate liquid flow and discrete element method (DEM) to resolve particle motion. The initial packing conditions consist of a binary-density particle system of 1130 particles each 1 cm in diameter. A variety of jigging profiles are implemented in jigging. The saw tooth pulsation profile is selected with three variations in both amplitude and frequency. The performance of each profile variant is compared in terms of solid flow patterns, separation kinetics, energy, and mean particle position. These quantitative comparisons demonstrate significant differences in the segregation rate, energy, and solid phenomena, helping find an alternative optimum operating setting for the system.

Sep 1, 2012

By R. J. Lloyd

INTRODUCTION The Mount Isa Mine is a large modern underground mine located in North-Western Queensland, Australia. Two ore types are mined and treated separately. Currently silver-lead-zinc ore is mined at the rate of 2.6 million tonnes per annum and copper ore at the rate of 4.6 million tonnes per annum. The silver-lead-zinc orebodies are mined by sub level open stoping and cut and fill methods whilst all copper ore is extracted by various forms of sub level open stoping. The mining operations are highly mechanised and utilise diesel powered load-haul-dump units of various sizes, two and three boom face drilling jumbos, electric-hydraulic rotary-percussive ring drills, in-the-hole hammer drills, rotary blasthole drills, raiseborers, battery/trolley locomotives, a large fleet of rubber tyred service and supply vehicles plus light rockdrills mounted on airlegs, rail mounted overshot shovels and battery and diesel powered locomotives. All stoping production ore is extracted with diesel powered load-haul-dump units. The ore is tipped into orepasses which connect to the main rail haulage levels. On the haulage levels electric battery/trolley locomotives are used to pull rakes of bottom dump or side dump trucks which feed the ore into primary crushers. Following two stage crushing the ore is conveyed to the shaft and hoistod to surface in bottom dump skips. Each ore stream has its own rail transport system, crushing stations and hoisting shaft feeding separate concentrators. This paper will consider some aspects of the role of equipment and machinery in the growth of the mine, will discuss in some detail the machinery and equipment in use today and will conclude with a look at some possible developments in mining equipment for the future, with particular reference to the Mount Isa Mine. A summary of mining equipment in use at Mount Isa is given in the Appendix. THE PAST Silver-lead-zinc ore was discovered at Mount Isa in 1923 and within a very short time many small mines were being developed. However the rich surface ore traces did not continue and by 1928 Mount Isa Mines Limited had acquired sufficient leases to plan for a large scale mine to exploit the low grade orebodies. At this early stage it was recognised that the mine would need to adopt the most mechanised mining techniques then available in order to overcome its twin disadvantages of low graaes and extreme remoteness. The Company introduced bar mounted drifters and overshot shovels to replace hammer and tap and hand shovelling in development work and by 1930 headings were advancing at the rate of 30 metres per week. In keeping with the concept of mechanisation the early engineers designed the Man and Supply shaft with a very large, for those days, cage compartment measuring 3.8 m x 3.4 m. This shaft was the main means of access into the mine for 36 years until the K57 shaft (now R62 shaft) was commissioned in 1966. Man and Supply is still in regular use. Production commenced in 1931 at an annual rate of approximately 660 000 tonnes of silver-lead-zinc ore. The mine was mechanised to an extent which was previously unknown in Australia; whilst the concentrator, smelter and power house utilised the most modern and efficient equipment available. Even so, the mine was very near to closure on several occasions and did not return a dividend to its shareholders for many years. Production levels remained at or slightly below 660 000 tonnes until a separate copper ore streani and mill was commissioned in 1953, doubling the existing production levels. The first underground crushers were installed at this time. Production rates expanded in the years between 1953 and 1973. By 1960 production reached 2740 000 tonnes of ore. In 1965-66 total production was 3650 000 tonnes and in 1973 the production rate plateaued at the current level.

Jan 1, 1981

By K. V. Konigsmann

"Concentrate dewatering operations have a significant influence on the economics of base metal beneficiation. The expenditures f or energy and labour per tonne of product are high. The relatively low efficiencies of standard techniques present inducements for process modifications. Development efforts at several Noranda concentrators led to process changes which improved productivity, namely, agitated pulp storage in large vessels, process automation and pressure filtration.IntroductionA program was initiated in 1968 with the aim of improving utilization of manpower and equipment in dewatering operations. The following considerations motivated us in this effort: Firstly, filters and dryers had traditionally been operated continuously and in step with grinding and flotation circuits. The demand for labour and equipment operating time was fixed and was not determined by the rate of concentrate production.Secondly, dewatering equipment had usually been designed to handle the concentrate tonnages which were produced when mill feed grades were high; therefore the equipment operated at less than capacity when treating ores of average metal content. The first goal was the separation of the flotation process from concentrate dewatering by development of a practical storage system for concentrate pulps . A second objective was the gradual introduction of dependable automatic controls. The steep increase in energy costs after 1973 added urgency to the search for dewatering processes which were highly energy efficient."

Jan 1, 1984

By Salinger, Herbert

WITH the large amount of metallurgical re- search work now being done and the constant effort of the engineer to effect economies of operation, I think it is a safe prediction that the next few years will see a great change in the handling of mine products. The well-managed mine, with sufficient ore reserves to warrant the necessary plants, will increasingly call upon the metallurgist and chemist for the solution of its problems. Shipping sorted ore or concentrate to the nearest smelter will not be the course followed. From ore to metal, or at least to a product directly salable to the consumer, will be the practice followed. As a consequence, mine managers will be increasingly interested in metal trade problems. By metal trade I mean the buying, selling, shipping, handling, and all the practices, forms and customs that go to make up the trade.

Jan 1, 1928

By E. Oshima

In May 1991, a New Mitsubishi Continuous Copper Smelter Line started operation at Naoshima. Recently, it has been continuing steady operation and one and a half year campaign life has been achieved. In 1996, new records of on line time, the amount of copper concentrate treated and copper anode production were achieved. 1t proves the superiority of the process with respect to pollution control, energy efficiency, flexibility and easiness of the operation and over all economy including off gas handling cost. Furthermore, .plans are underway to prolong the campaign life for two years and to improve the process efficiency. This paper describes recent operation, improvements, and a future capability study.

Jan 1, 1998

IN preparing a sample of refined lead for analysis, it is necessary to exercise great care to avoid contaminatien, as the amounts of the various impurities present in market lead are very small. The lead is cut into convenient-sized pieces, which are flattened out with a hammer, so that, on putting tbe lead through the rolls, strips of about one inch in width and Ij32iu. in thickness are obtained. The hammer, anvil, and rolls should be carefully cleaned before use. The strips oflead are cut up into pieces of about one inch square. If the lead is roIled out very thin and cut up into small pieces there is considerable risk of the acid acting too violently and causing loss through frothing over. A blank assay on all the reagents used should becarried right through, along with the actual analysis of the lead. This is of the greatest importance, particularly with regard to the determination of such impurities as iron, sulphur, arsenic, and antimony.METHOD OF ANALYSISThe method of analysis is as follows: Take two lots of 600 gIm. each, place in a large beaker, add 2000 cc. distilled water and 750 cc. concentrated HNOs. Cover with a clock glass and warm on a hot asbestos plate until all action ceases. (If any white precipitate forms, filter off and examine for Sn and Sb.) Add 420 cc. H2S04 (1-1), and stir well while adding the acid: Allow PbS04 to settle, pour off the clear liquid into a 12-in. porcelain evaporating dish, and start evaporating down, the dish being placed directly on an 8-in. ring gas burner. Wash the precipitate three times by decantation using approximately 1200 cc. hot water for each washing, and stir well...

Jan 1, 1922

THOSE NOT MARKED ARE MEMBERS; MARKED THUS ?ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP JUNIOR MEMBERS ARE MARKED ' . THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD See Honor Roll. '05 ? AARONSON, ALFRED E Pres., Tuloma Oil Co., Unity Bldg., Tulsa, Okla. '18 ABADIE, EMILE R., Min. En r Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Fujitagumi Taiwan Office, Taipeh, Formosa, Japan. '14 ABBY, HIROSHI Min. & Met. Engr., Mitsubishi Co., Tokyo, Japan. '17 ||ABOUCHAR, S. S., Cia. de Minerales y Metales, S. A., Minas Viejas, Villaldama, N. L., Mexico. '17 ABRAHAMS, A. I 1391 Madison Ave., New York, N. Y. '14 ?ACKER, E. O'C., Met.,128 East Washington Lane, Germantown, Philadelphia, Pa. '86 ? ACKERMAN, ERNEST R., Pres., Lawrence Portland Cement Co., Plainfield, Union Co., N. J. '15 ACOSTA, J. N., Min. Engr., Cons. Engr Hotel Brewster, San Diego, Cal. '15 ADACHI, JINZOO 11 Shiba Park, Shiba-Ku, Tokyo, Japan. '88 ADAMI, CHARLES J., Min. Engr., Gen'l Supt., St. Joseph and Doe Run Lead Companies, Bonne Terre, Mo. '12 ADAMS, ARTHUR K., Min. Geol., Andes Copper Min. Co., Casilla 230, Antofagasta, Chile. '06

Jan 1, 1923

On the Art of Metallography (Howe Memorial Lecture), by F. F. Lucas; Beneficiation of Iron Ore. Abstract of paper by C. E. Williams followed by Round Table Discussion; A Statistical Analysis of Blast-furnace Data, by R. 8. McCaffery and R. G. Stephenson; Air Discharge of Circular Tuyeres, by R. S. McCaffery and D. E. Krause; Open-hearth Steel Process as a Problem in Chemical Kinetics. by E. R. Jette; Carbon-oxygen Equilibrium in Liquid Iron, by H. C. Vacher and E. H. Hamilton; A Thermodynamic Study of the Phasial Equilibria in the Bystem Iron-carbon (Abstract), by Yap, Chu-Phay; Influence of Dissolved Carbide on the Equilibria of the System Iron-carbon (Abstract), by Yap, Chu-Phay; Inclusions and Their Effect on Impact Strength of Steel, I and 11, by A. B. Kinzel and W. Crafts: Method for Electrolytic Extraction of MnO, MnS, FeS and Si02, Inclusions from Plain Carbon Steels, by G. R. Fitterer; Permanent Growth of Gray Cast Iron, by W. E. Remmers; Some Notes on Blue Brittleness, by L. R. van Wert; Austenite-pearlite Transformation and the Transition Constituents, by A. Sauveur; Age-hardening of Austenite, by F. R. Hensel; Transformational Characteristics of Iron-manganese Alloys, by H. Scott; Composition Limits of the Alpha-gamma Loop in the Iron-tungsten System, by W. P. Sykes; Magnetic Properties Versus AUotropic Transformations of Iron Alloys, by T. D. Yensen and N. A. Ziegler; Dilatometric Study of Chrome-nickel-iron Alloys, by V. N. Krivobok and M. Gensamer; Low-carbon Steel, by H. B. Pulsifer; Bright Annealing of Steels in Hydrogen, by F. C. KeUey; Development of Continuous Gas Carburieing, by R. J. Cowan. Transactions, Institute of Metals Division, 1931. 500 pages. Index. Papers and discussions presented before the Division at Chicago, Sept. 22-26, 1930 and New York, Feb. 16-19, 1931. X-ray MetallograpIhy: X-ray Determination of Alloy Equilibrium Diagrams (Annual Lecture), by A. F. Westgren; Suppressed Constitutional Changes in Alloys. by G. Sachs; Texture of Metals after Cold Deformation; by F. Wever. Theoretical Metallurgy: Studies upon the Widmanatitten Structure. I.—Introduction. The Aluminum-eilver System and the Copper-silicon System; by R. F. Mehl and C. S. Barrett; Studies upon the Widmanstatten Structure, 11.—The Beta Copper-einc Alloys and the Beta Copper-alumnum Alloys, by R. F. Mehl and 0. T. Mareke; Application of X-rays in the Manufacture of Telephone Apparatus, by M. Baeyerts; Thermal Conductivity of Copper Alloys. 11.—Copper-tin Alloys; 111.—Copper-phosphorus Alloys, by Cyril Stanley Smith; Thermodynamic Study of the Equilibria of the Systems Antimony-bismuth and Antimony-lead, by Yap, Chu-Phay. Ganeral: Cemented Tungsten Carbide; a Study of the Action of the Cementing Material, by L. L. Wyman and F. C. Kelley; Influence of Casting Practice on Physical Properties of Die Castings, by C. Pack; Fabrication of the Platinum Metals, by C. S. Sivil; Effect of Certain Alloying Elements on Structure and Hardness of Aluminum Bronze, by 9. F. Hermann and F. T. Sisco. The WorkinG oF Metals: Metal Working in Power Presses, by E. V. Crane; Forming Properties of Thin Sheets of Some Nonferrous Metals, by W. A. Straw, M. D. Helfrick and C. R. Fischrupp; Die Pressing of Braas and Copper Alloys, by J. R. Freeman. Jr.; Plasticity of Copper-sina Alloys at Elevated Temperatures. by A. Morris: Directional Properties in Cold-rolled and Annealed Copper, by A. Phillips and E. 9. Bunn; Effect of Combinations of Strain and Heat Treatment on Properties of Some Age-hardening Copper Alloys by W. C. Ellis and E. E. Schumacher; Constituents of Aluminum-iron-silicon Alloys, by W, L. Fink and K. R. Van Horn; Equilibrium Relations in Aluminum-antimony Alloys of High Purity, by E. H. Dix, Jr., F. KeUer and L. A. Willey; Equilibrium Relations in Aluminum-magnesium Silicide Alloys of High Purity, by E. H. Dix. Jr., F. Keller and R. W. Graham; Constitution of High-purity Aluminum-titanium Alloys, by W. L. Fink, K. R. Van Horn and P. M. Budge; Experiments on Retarding the Age-hardening of Duralumin, by E. H. Dix. Jr. and F. KeUer; Aluminum-silicon-magnesium Casting Alloys, by R. S. Archer and L. W. Kempf; Modulurr of Elasticity of Aluminum Alloys, by R. L. Templin and D. A. Paul; Quenching of Alclad Sheet in Oil, by H. C. Knerr.

Jan 1, 1931