Search Documents

By C. F. Weinaug, R. W. Farley, J. F. Wolfe

A rapid, accurate method for predicting the dew points of gas condensate systems and their subsequent normal and retrograde phase behavior with pressure decline has been developed. The method predicts dewpoint pressure, volume percent liquid, condensate content of produced gas, and the liquid and gas compositions at pressures below the dewpoint pressure. Use of a modified form of the BWR equation of state, which was established by regression calculations on experimental data from several gas condensates, provides depletion behavior predictions that are significantly improved over predictions using K-values based on convergence pressures and Standing's correlation for density. INTRODUCTION Prediction of complex hydrocarbon-mixture thermodynamics is fundamental to reservoir and gas process engineering. In particular, accurate descriptions of phase behavior are needed to plan production operations for gas-condensate reservoirs. Although analysis of reservoir behavior during producing and cycling operations can be made for simple reservoir models, extensions of these studies to more complex reservoir systems are still difficult, both with regard to numerical techniques and the phase behavior of the fluids. This report presents a mathematical method for handling the complex phase relationships encountered in retrograde condensates; it represents an advance in reservoir behavior technology in that it will aid the development of closed-form mathematical representations of total production systems. A typical phase diagram for a complex hydrocarbon mixture is shown in Fig. 1. When the reservoir temperature T, is higher than the critical temperature Tc, and lower than the critical-condensation temperature Tct' the mixture is a gas condensate. Decreasing the pressure on a condensate while maintaining nearly constant temperature will result in two phases forming at the dew point. Further decrease in pressure will cause additional liquids to be formed. This phenomenon is called retrograde condensation. As pressure continues to decrease, normal phase behavior regions are encountered (liquid vaporizes as the pressure decreases) until the low-pressure dew point is encountered. When a gas-condensate reservoir is produced, gas is withdrawn and the volume of fluids in the reservoir remains nearly constant as the pressure declines. Heavier components tend to accumulate in the liquid phase as a result of retrograde condensation, while lighter components tend to concentrate in the vapor phase. Thus, as the gas is produced the composition of the gas and the condensate

Jan 1, 1970

It doesn't take any special acumen to note that US engineering and construction firms are busier than ever with mining projects in this mineral conscious world. This special issue of Mining Engineering takes a look at E&C companies-their expanding role, their special capabilities, and their challenges and problems. ME sent a questionnaire to a representative sample of E&C firms. Information was sought about officers, ownership, and amount of business. ME also asked about types of projects and commodities dealt in as well as market distribution and forms of payment. The accomnanying charts show how the 17 responding E&C firms answered these and other questions. Other ME survey questions, and a review of company literature, yielded information about financing techniques and special challenges for E&C firms. Insights were gained concerning government impacts, customer-generated problems, and promising areas for development-including synfuels-in the minerals industry. These areas are discussed later in this article. Accompanying articles in the special issue discuss the E&C company's role in mining projects, research and development in E&C firms, one approach to contract work used by an E&C firm, and an E&C project case study.

Jan 10, 1980

By Rodolfo V. de la Cruz

The in-situ deformability of a highly jointed basalt rock mass was determined by two distinctly different methods: one, by the NX- borehole jack method where the displacements of opposing curved platens were related to the applied hydraulic pressures, and; two, by the modified Goodman jack method where the tangential strains on the borehole walls were related to the induced tangential stresses. The modulus obtained by the modified Goodman jack method were much higher than those obtained by the NX- borehole jack method. To explain the discrepancy, the influence of fractures and test variables such as depth, orientation, hole number and applied pressure on the calculated modulus of the rock mass were analyzed by factorial analysis and it was found that the orientations and depths of measurement has statistically significant effects. The in-situ deformability values obtained by non-linear regression analysis were also found comparable with other measurements and empirically predicted values for the basalt rock mass.

Jan 1, 1982

By M. Paul

"INTRODUCTION In 1990, the uranium production of SDAG Wismut in East Germany was stopped. 45 years of inconsiderate destructive exploitation had scarred both landscape and nature. With the “Wismut law” which came into force in December 1991, the Federal Republic took responsibility of the remediation of the legacies from former uranium ore mining and milling in Saxony and Thuringia. A unique opportunity turned out in order to remove environmental damage, to enhance the life quality of the local population, to shape new landscapes and to advance the economic restart. (1) The results of nearly 25 years of remediation activity are evidence that this opportunity was used at all former SDAG (Sowjetisch-Deutsche Aktien-gesellschaft) Wismut sites. The reference project “Wismut“ has evolved into a joint project of all parties involved and radiates beyond the affected regions. This is particularly reflected by the Know-how transfer starting from Wismut and the increasing activities for third parties abroad.WATER MANAGEMENT AT WISMUT REHABILITATION Within the Wismut project, water management and conventional technical water treatment are by far the most cost-intensive long-term tasks of the remediation programme. Over the medium term, there is no viable alternative to the operation of active systems to catch and treat contaminated mine waters at the Ronneburg, Schlema, Königstein, Pöhla, Seelingstädt and Helmsdorf sites. Based on the status quo, this paper outlines the key issues of the Wismut GmbH water management strategy over the medium and long term. It is focused primarily on achieving protection goals for potentially impacted water bodies in the surroundings of Wismut sites and on optimising associated remediation expenditures as well as on creating the prerequisites for achieving low post-remedial care and maintenance or walk-away system status over the long term. (2) The applied mining practices during the active SDAG Wismut period have not been up to the high standards of modern mining operations and their requirement to leave former production premises and deposited residues in a condition that was not only physically but also chemically stable. Rather the emission of mine and seepage waters laden with high acidity, metal and salt content is a frequent corollary and difficult legacy of historic mining and processing operations (4, 5). As a consequence, the control or mitigation, respectively, of environmental impacts associated with contaminated mine waters ties up enormous public resources worldwide (6, 7)."

Jan 1, 2016

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By Changhong Huang, Y. J. Wang

This paper describes the formulation of mine ventilation network optimization as a standard nonlinear programming problem and the solution of the problem using the generalized reduced gradient (GRG) method. In general, the GRG method is regarded as one of the most effective and efficient methods for solving large-scale nonlinear programming problems. The variables considered in the network optimization include air quantity, regulator pressure loss, and fan pressure for each branch. Each of the variables is constrained by lower and upper bounds. This facilitates proper assignments of ventilation requirements and provides a great flexibility to include various situations encountered in mine ventilation. The objective of the network optimization is to minimize the overall air power consumed by or supplied to the network; whereas the constraints are, in addition to the variable bounds, the two fundamental network laws: Kirchhoffs voltage law and Kirchhoffs current law. A computer program has been developed based on the GRG method for the network optimization. An example of network with 18 branches, 8 regulators and 3 fans is included for illustration.

Jan 1, 1993

Discussion of the paper of J. C. Febles, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 191.3, pp. 1267 to 1283. J. W. RICHARDS,. South Bethlehem, Pa. :-In looking at these precipitating launders the idea has come to me that the iron could probably be kept much cleaner if there were laid on the bottom of the . launders some sheet copper, with which the iron would be in contact, and as the solution passed over the tendency would he to precipitate the copper on the sheet copper and thus keep the iron cleaner than it is under present conditions. As soon as a piece of iron becomes coated with copper, its surface becomes inactive, and the presence of a sheet of copper in electrical contact with the iron would tend to precipitate the copper on the sheet copper and to keep the iron clean.

Jan 11, 1913

By Martin E. Nelson

Several heavy metal separation techniques are currently being developed for soil remediation at various Department of Defense and Department of Energy (DOE) Facilities. The majority of these techniques involve a wet process using water, PH modifiers or other compounds. The United States Naval Academy (USNA) has developed a dry process for heavy metal separation. The process uses air classification technology to concentrate the metal contaminant into a fraction of the soil. The advantages of this dry process are that it creates no contaminated by product and uses commercially available technology. The USNA process is based on using a Gayco-Reliance air classifier. Tests have been conducted with the system at the Naval Academy and the University of Nevada-Reno (UNR). The USNA tests used soil from the Nevada Test Site mixed with bismuth at a concentration of 500-1000 ppm. The UNR tests used soil from four DOE sites mixed with uranium oxides and plutonium at an activity level of 100-700 pCi per gram. Concentration of activities and volume reduction percentages are presented for the various soils and contaminants tested.

Jan 1, 1995

By K. Asokan, K. Subramanian

"Electrowinning of copper by monopolar cells require common anode and cathode busbar and crossbars to connect each electrode to the respective common busbar. On the other hand, the bipolar configuration warrants the end electrodes only to be connected to busbars; there is substantial reduction in copper requirement. In the present work, an electrowinning cell with bipolar electrodes and end electrodes, each having an area of 1000 cm2 was designed and operated. The bipolar electrode is made of mixed metal oxide coated titanium mesh welded to plain titanium sheet. Coated titanium mesh acts as anode and the plain titanium sheet acts as cathode. Environmentally unacceptable lead anode and the recurring loss of lead are done away with. Closer spacing of the electrodes, paves way for the application of higher current density leading to mass transfer enhancement. Performance of bipolar copper electrowinning cell is reported.1. IntroductionThe normally adopted practice in electrowinning of copper is the conventional monopolar configuration. In this practice, the individual electrodes act either as anode or cathode. Hence there is a need to connect every one of the electrodes to the common anode or cathode busbar and crossbars running across the top of the cell are necessary. The common busbar carries very high current which is divided among the individual crossbars and hence has to be thicker in relation to the current load of the cell. The drawback of the need to use common busbars of thicker cross section and the need to have crossbars are obviated in the bipolar configuration."

Jan 1, 2009

By M. L. Young, M. S. Klima

Hindered-settling columns are used throughout the minerals industry for both size and density separations. In this study, the performance of a continuous laboratory-scale hindered-settling column was evaluated for various particle systems. The test variables included solids composition, water rate and column height. Column performance was evaluated using partition curves and corresponding performance parameters.

Jan 1, 2000

By Donald E. Ralston, V. Rajaram, Michael N. Greeley, John W. Peters, Terry J. Laverty, F. S. Kendorski, Peter G. Chamberlain, J. Brent Hiskey, William C. Larson

Preliminary figures from the US Mine Safety and Health Administration show 801 underground metal mines and 490 surface metal mines, at the end of 1981, up from 663 and 383, respectively, in 1980. Preliminary MASH figures also show 207 underground nonmetal mines and 1070 surface nonmetal mines at the end of 1981, compared with 167 and 1092, respectively, last year. In addition, preliminary MASH figures show there were 14,676 mineral extraction operations on the surface and 3845 underground at the end of 1981, versus 14,951 and 3675, respectively, for last year. The number of mines, then, in three of four categories increased significantly, while having a lower net total of just 2% in the other category. And the number of underground extraction operations increased nearly 5% for the year, while surface operations were down less than 2%. But despite operations totals that mostly held their own or showed significant increases, it was a tough year for the nation's mining industry. The nonferrous segment of the industry had a bad year and 1982 may be no better, according to Business Week (Jan. 11, 1982), which adds that a turnaround is impossible unless the general economy recovers. Even then, with diminishing markets and overcapacity plaguing its products, the mining industry's condition "will be far from robust," the magazine says. The basic problem is that nonferrous metals-aluminum, copper, lead, molybdenum, nickel, and zinc-are tied to the most troubled sectors of the US economy. As recently as 1979, for example, more than 40% of all aluminum shipments went to the construction and transportation industries. Last year, these markets were down to 35% of aluminum shipments. And molybdenum sales to steel producers dropped by nearly 15% last year. Moreover, nonferrous products ended 1981 at disastrously low prices. Molybdenum oxide sold at $8.77/kg ($3.98/lb), half its $17.63/kg ($8/lb) price earlier in 1981 and aluminum was listed at $1.08/kg ($0.49/lb), compared with $1.54/kg ($0.70/lb) a year earlier. The Comex price of copper was $1.54/ kg ($0.70/lb), down from $3.11/kg ($1.41/lb) in early 1980, in real terms the worst copper price in 30 years. Lower prices led operators to cut their output and increase layoffs, shut down mines, and defer capital spending projects. In December, Duval Corp., a Pennzoil Co. subsidiary, shut all four of its US copper mines until March. Aluminum Co. of America had laid off 7.3% of its work force, shut nine of its 38 smelting lines, and entered 1982 operating at only 68% of capacity. Inco Ltd., the Free World's largest nickel producer, lost money in 1981, an estimated $11 million, for the first time since 1932. And, like Falconbridge Nickel Mines and other major nickel producers, had cut back on nickel production and was operating at only 63% of capacity (Forbes, Feb. 15, 1982). Amax, the country's largest molybdenum producer, had cut production by 20%. And Hanna Mining Co. sold lead for $5.07/kg ($2.30/lb), about $1.54/kg ($0.70/lb) below what it cost to produce. Another problem is that copper companies in the next few years must come to terms with problems of aging smelters. Some companies are simply closing them. In 1980, Anaconda closed its 75-year-old Butte, MT, smelter and is shipping concentrates to Japan, rather than modifying the smelter to meet environmental requirements. And oth Phelps Dodge Corp. and Asarco Inc. have antiquated smelters on which they will have to make decisions. The most troubled metal in 1982, Business Week said, will be molybdenum, with no real recovery in sight until the mid-1980s. High molybdenum prices in the late 1970s, caused in part by shortages, triggered overexpansion that will take years for the US market to soak up. On a more upbeat note, 1981 mergers might help stabilize the industry by providing funds for mining companies. Standard Oil Co. (Ohio) said it plans to spend $7 billion on Kennecott during the next 10 years for modernization and expansion. And Atlantic Richfield Co. said it will spend $500 million on Anaconda Copper Co. during the next five years. Another positive note was sounded by T. H. Adams of the United Banks of Colorado Inc. He said he expects the mining industry to experience moderate growth in 1982, led by "interest rate sensitive" demand from energy, electronics, and defense markets. And mining will be helped by "weak, but improved" construction and auto markets. The mining industry will be operating in an economy stronger than 1981, but still relatively sluggish by postwar standards, Adams predicted. Iron Ore Estimated US iron ore production in 1981 was 75.2 Mt (74 million long tons), up 6% from 70.7 Mt (69.6 million long tons) in 1980, though down from the 87.1 Mt (85.7 million long tons) produced in 1979. The mine value of usable iron produced from domestic mines was estimated at $3 billion. US iron ore was produced by 28 companies operating 35 mines, 26 concentration plants, and 16 pelletizing plants. The mines included 34 open pits and one underground mine. Byproduct ore recovered from copper- and titanium-mining operations accounted for less than 1% of total iron ore production. Fifteen mines operated by nine companies accounted for 94% of total

Jan 5, 1982

By Albert Sauveur

It is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.' The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance. Physical Properties of Cast-Iron us. Its Ultimate Composition. Mr. Johnson writes that " an investigation along the lines of consumption showed that different irons have different characters totally independent of their analyses," and he declares that " the presence or absence of these elements [meaning carbon, phosphorus, silicon, and manganese] alone will not account for all, scarcely for a half, of the facts which have long been known." He further tells us that some foundries have " proved, by the most irrefutable tests, that they could take a certain iron of a given analysis and produce certain results," while with " another iron of the same analysis they could not produce these results at all." I feel confident that every experienced and thinking metallurgist will readily believe Mr. Johnson's statements and will share his views in regard to the hopelessness of inferring the

Jan 1, 1914

By Arthur Laing

"IT is indeed a pleasure to have the opportunity of addressing this group today. Not only does it give me the opportunity of meeting with representatives of what is considered by many to be the most dynamic segment of industry in Canada today, but it also allows me to talk about a subject of para-mount interest to myself, the development of the North, and to explain, if even only briefly, some of our beliefs and hopes in this regard.It is inconceivable that all lands north of the 60th parallel, representing 35 per cent of Canada's total land area, which we believe contain a great natural resource potential, will remain as an undeveloped portion of Canada. The re-sources are there, although the people and private industry are as yet not there in sufficient numbers.It has been estimated that in the west and north of Canada there are 1.6 million cubic miles of sedimentary rocks. Of this figure, 342,-000 are thought to lie in Alberta, 115,000 in British Columbia and about 1 million cubic miles are thought to lie in Canada's northern regions, the bulk in the Arctic Islands. On the basis of apparent volumes of sedimentary rock, we estimate that as much as 13 billion barrels of petroleum may lie beneath the permafrost of the North-west Territories, another 3 billion barrels in the Yukon Territory and 33 billion barrels in the Arctic Islands. This is, indeed, a rich and elusive prize, and one which must be sought with a view to fulfilling demands on the production of petroleum."

Jan 1, 1966

By Dan Crackel, G. G. Ramos, Mark Heisel

INTRODUCTION Feasibility studies indicated that a cratering type stoping method was best suited to the character of the first ore block at Carr Fork. This method known as vertical crater retreat (VCR) has since been modified to a combination cratering and deck blasting using VCR drop raises for initial undercut development . The modified form retains many of the advantages of VCR while allowing high tonnage production blasts which have offset many of the disadvantages. FIRST CONCEPTS AND PREMISES Geologic Considerations The Steep Highland Boy (SHB) skarn orebody, the first of several blocks being developed, is a steeply dipping 70° to 90° limb of a syncline, with a width averaging 25 m (82 ft). The bed has a consistent east-west strike length of over 400 m (1300 ft) and extends from the surface to depths of over 1000 m (3300 ft). The footwall is highly fractured quartzite and the hanging wall grades from garneti te to limes tone and hornfe 1s. Because of the limestone in the hanging wall, the hanging wall appears more competent than the footwall. The ore is garnetite with lenses of massive sulphide and magnetite. The quartzite footwall is highly fractured not only because of the bedding but also due to the folding and intrusion of the quartz monzonite. This irregular footwall outline of some stopes in- creases the likelihood of excessive dilution. The principal ore mineral is chalcopyrite with some bornite. The garnetite ore is quite variable in terms of compressive strength and drillability. In addition to the sulphide and magnetite lenses, it is transected by clay- altered dikes and major and minor north-east faults. TABLE (1) gives the range and mean strengths of the rocks. Investigating Mining Methods Initial consideration of a suitable mining method centered around maximum safety and efficiency with minimum potential dilution. The following major methods were considered and investigated. Cut and fill mining was eliminated because of low productivity, the cost and problems associated with providing fill, and the relatively unsafe nature of the method. Sublevel caving was rejected due to the unpredictable cavability of the waste and the geometry of the ore body. Conventional sublevel or blasthole methods require excessive development, as fan and ring drills are limited to efficient drilling in the 18 to 25 m range (60 to 80 ft). Mining downdip with equipment drilling small diameter holes would have required eight separate extraction/drill horizons with crosscuts and associated excavation in the main ore block. The use of down the hole (DTH) machines cap- able of drilling 165 m (6g in) diameter holes

Jan 1, 1981

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

By D Andrew, G Stanway, P Mahoney, C Griebel

The iron ore mining industry is currently going through an adjustment from high to more moderate growth as China’s economy transitions from capital-intensive investment to a more services-oriented economy. We are now witnessing a renewed focus on productivity improvements and cost savings as planned expansions are completed. Despite the scale and importance that the mining industry plays in the global economy, innovation literature is generally more targeted at faster-moving industries with shorter innovation timeframes and lower capital requirements. To fill this gap, VCI set out to understand the state of innovation in the mining industry in 2014. This State of Play report aims to give an objective appraisal of the strengths and weaknesses of innovation in mining. The report has three sections covering both the structure and delivery of innovation in mining:Ecosystem – focused on understanding how the iron ore mining innovation ecosystem system works, including the roles of large and small miners, service companies, researchers and governments. Our recommendations focus on what is required for the system to work well and improve the level and quality of innovation in the industry.Strategy – how do companies define their innovation strategy in relation to their corporate strategy? How are these related to prevailing global and industry trends? How do they communicate this with their business? How successful are they? These are among the questions that this section attempts to answer. Our recommendations are pitched at the executive leadership of iron ore mining and service companies.Delivery – focused on how companies develop and deliver innovation, looking at the success of different structural options, leadership and culture, partnerships and the best approaches to change. Recommendations are aimed at improving outcomes within the iron ore mining value chain, including the role that suppliers play.CITATION:Stanway, G, Mahoney, P, Andrew, D and Griebel, C, 2015. Understanding the state of innovation in the iron ore industry, in Proceedings Iron Ore 2015, pp 631–646 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Jan 1, 1914

By W. F. McDermott

One of the major improvements in ore grinding economics in North America has been the introduction of autogenous grinding. The history of this has been well documented in previous AIME presentations and in the literature. Pickands Mather & Co. has been very active in the development of autogenous grinding since 1957. This early work led to the application of autogenous grinding to the Wabush Mines ore in 1965, with the installation of 6-24 ft. diameter by 8 ft. long - 1,750 HP mills. Development work recently completed in 1971 on another ore has led to the decision to install 5-36 ft. diameter by 15 ft. long - 12,000 HP mills when this project goes ahead. Between these two decisions lies a tremendous amount of research, development, and application of autogenous grinding to a variety of ores. The Pickands Mather Metallurgical and Research Laboratory in Hibbing, Minnesota has tested, in its pilot plant facility, ores from 9 different deposits. Some of these deposits have as much difference within their own ore types as there is between the various deposits. Therefore, it is safe to say that over 20 different ore types have been tested and flowsheets developed for commercial applications. Of the 9 projects, 3 are in operation. These are Wabush Mines in Labrador, Canada, (1) Savage River Mines in Tasmania, (2) and The Griffith Mine in Red Lake, Ontario, Canada. (3) Pilot plant work has encompassed over 300 individual tests. These tests were carried out in mills that were 5-1/2, 8, and 12 ft. in diameter. Grinding power requirements for the primary autogenous milling has varied from 2 to 30 KWH/Lt of crude ore.

Jan 1, 1972

By Shonn K. McNeill, Joshua Micah Hoffman

Security engineering is similar to other forms of engineering – the design is guided by the loads, materials, and desired function. For facility design, the load is the threat. Facilities that are designed with considerations for explosive hazards are designed with a shot, or series of shots, of a given size and distance from key locations. These facilities range from office buildings and industrial sites in developed nations to military and police stations in contingency areas. The challenge is the design shots are not often communicated to facility owners and managers. If the hazards change, whether it’s due to an increased capacity to cause damage by a threat or a decrease in capacity by a structure, not knowing the design shot means not knowing if security design needs to change. Blast modeling is an engineering tool that can be used to reverse engineer what a facility is suitable for, as well as be a tool for modifying security design for new conditions. This paper will examine military and civilian examples, including a case study of a military facility that did not know their as-built conditions and had to be rapidly closed; due to the determination their security engineering shortcomings could not be mitigated.

Jan 1, 2019