Search Documents

By H. H. Hausner, O. V. Roman, F. V. Lenel, G. S. Ansell

The radial shrinkage during sintering of cylindrical compacts and loose aggregates of copper powder was measured. It was found to be nonuni-form from top to bottom of the samples and to depend upon the method of supporting them. The non-uniformity is due to the effect of gravity forces during sintering. Since gravity has an effect in sintering without externally applied stresses, no sharp dividing line can be drawn between conventional sintering and hot pressing. RECENT investigations of the sintering behavior of compacts1 and of loose powder aggregates2 have indicated that forces, other than those arising from surface tension effects, may play a role in shrinkage. In compacts it was shown that residual stresses from the pressing operation influence shrinkage behavior. In loose powder aggregates gravity forces due to the weight of the powder affect the ratio of shrinkage in the vertical and the horizontal direction. The main effort in the work reported here was to show that gravity plays a role also in the sintering of compacts. A few additional experiments were made confirming the effect of gravity in the sintering of loose powder aggregates. EXPERIMENTAL PROCEDURE Compacts and loose powder aggregates were prepared from irregularly shaped, electrolytic copper powder. Prior to use the powders were reduced 30 min at 400°C in dry hydrogen to remove surface oxides. Then the -325 mesh size fraction was separated from the -100 + 325 mesh fraction. The compacts were pressed at a pressure of 10,000 psi from 50 g of powder in a hardened steel die, 1 in. in diam. The height of the compacts was 0.725 i 0.005 in. An effort was made to get as uniform a green density distribution in the compacts as possible. The walls of the die were lubricated with a suspension of 3 pct of zinc stearate in acetone and the compacts were pressed using double action by first pressing the powder at 1200 psi with the die barrel supported, then removing the sup- ports and pressing to final pressure of 10,000 psi with the die barrel floating. The pressure was maintained for 10 sec. The compacts were sintered at a temperature of 925°C, generally for 1 hr. In order to maintain uniform temperature they were sintered in boats made from cylindrical copper blocks. The blocks were 2 in. in diam, either 2 or 2 1/2 in. long and, split to form the body of the boat and a lid. The body of the boat contained a cavity 1 3/8 in. wide, 1 in. deep and either 2 1/8 or 1 3/8 in. long. The longer cavity accomodated two samples, the shorter one only one sample. The uniformity of temperature distribution within the boats was checked with thermocouples welded to the top and bottom of the samples. The maximum variation between top and bottom temperatures was i 1/2°C. The actual sintering temperature was held constant within ±2°C. In order to determine the effect of gravity forces, i.e., the weight of the compacts, upon shrinkage, they were supported in the following ways during sintering: a) Full Bottom Support. The compacts rested either on a flat alundum disk or on alundum powders. b) Partial Bottom Support. The compacts rested on a graphite cylinder, 0.3 in. in diam which formed a projection on a larger graphite disk. It is difficult to balance the compact on the small projection. To avoid having the compact tip, a small hole was drilled through the compact and through the graphite disk and its projection. The graphite disk was then suspended from the lid of the boat by a thin iron wire which passed through the holes in the disk and the compact. c) Top Support, first type. A hole 3/32 in. in diam was drilled diametrically through the green compact 3/16 in. from the top of the compact. The compact was sintered suspended from an alundum rod (thermocouple protection sleeve) inserted into the hole. d) Top Support, second type. A hole was drilled axially through the center of the compact. The upper part of the hole from the top surface of the compact one fourth of the way down was 1/16 in. in diam; the lower part of the hole from the bottom surface three fourth of the way up was 3/32 in. in diam. The compact was suspended from the lid of the boat by an iron wire passing through the upper part of the hole and then tied into a knot. The loose powder aggregates were made by filling l in. deep, l in. diam cylindrical graphite molds with -325 mesh powder. To achieve uniform density in all the loose powder aggregates, the powders were settled in the molds by placing the

Jan 1, 1963

By W. W. Cotter, W. R. Clark

WEBSTER tells us the word "extrude" means to "force, press or push out; to protrude." As applied to the metal industry, the process consists largely of forcing plastic elements (plasticity usually obtained by preheating), through dies of predetermined profiles, into constant sections of considerable length and weight. Most of the "virgin" metals are quite malleable under this process, likewise many of the commonly used "alloys" in various industries, when basic elements are proportioned or combined within the natural laws and limits of good metallurgy. Several of the foundry alloys, both ferrous and nonferrous, together with some of the heat-treatable light metal mixtures, are decidedly weak and hot short at ordinarily plastic ranges, and consequently are troublesome or quite incapable of commercial extrusion. DEVELOPMENT OF PROCESS This process was conceived some time before 1800 and during its first century was employed almost entirely in making lead pipe, plumbing fittings and coating electrical cables. As a result of contact and experience with the lead industry and presses, Alexander Dick, of London, England, is credited with first having applied the principles of extrusion to brass, and in 1894 brought out a 500-ton horizontal press powered by hydraulics. A duplicate of this unit was imported by one of the Connecticut brass mills and was in experimental operation by 1900. During the first five years of operation, this press proved the value of the method to American industry, as it immediately revolutionized and converted the manufacture of brass rod from a 15-pass cold-rolling operation, with elimination of several intermediate anneals and cleanings, to an extrusion and a finishing draw. Likewise, ornamental brass and bronze moldings formerly cast and machined were produced in one squeeze on the extruder. The extrusion operation, being entirely that of compression, deforms the material without tensile stresses and can be used on delicate mixtures under heat, which cannot be hot-worked by straight hot-rolling or roller piercing. Base slabs of clock-brass strip were early in line of development or improvement, as were the brass bronzes (Naval brass, Muntz metal, manganese bronze, and others), popular as engineering materials for bolt stock, as well as structural shapes for marine and other mild conditions of corrosion. By 1910, American engineers undertook to design tube shell extruders, but were unsuccessful. The first World War began before fabricators could procure the more substantial designs of tube extruders produced in Germany; and it was not until the middle twenties that better models of the Universal extruders (double-actioned presses), equipped with hydropneumatic accumulator systems and other modern equipment, were available in the United States.

Jan 1, 1945

By Bogdan Petkovic, Boban Todorovic

In the early 90's a completely unknown problem was encountered at the converter Department: it was a chronic shortage of the cold copper charge needed for the second operating period. A high temperature operating regime was caused which further provoked a chain of consequences such as a drastic drop of the number of operations in campaigns. The consumption of repair bricks reached the quantity of 8.3955 kg / tonne of anode Cu. In 1994, we won the process of cold material smelting during the "copper" blowing [2]. The number of operations per campaign reached 180-200 again. Also in 1994 we won the process of smelting cold materials to obtain "tin" blowing with the purpose of completing their processing cycle [2]. During the period 1994 – 2007 a total of 107,845 tonnes of cold material were remelted to make copper and 56,794 tonnes were re-smelted to obtain "tin". Upon synthesizing these two processes, a completely new model was achieved in 2005, by Bogdan Petkovic, which entirely utilized all available energy of the Peirce-Smith (PS) converters of the Bor Copper Smelter and now represents the basis of the time cycle. The cold material now enters the converter plant, copper recovery is increased and the method itself is environmentally friendly. 167

Jan 1, 2009

By L. O. Howard

TWO or three years ago there were submitted to me some reports of tests that had been made on a semi-oxidized ore of silver looking to its treat-ment by combined flotation and cyanidation, together with a sample of the ore, with a request that I check the tests and confirm them, if possible. These tests had been made by a machinery-supply house and with them was a flow-sheet for a proposed mill, with full details of equipment to be used in the mill. The limited data on which this was based at once attracted my attention and have caused me from time to time to put various groups of students at work to develop simpler methods of obtaining data, which it appeared should be at hand and could be obtained by simple tests before attempting to treat these ores commercially. A brief discussion of the working out of such methods may be of interest and may contribute somewhat to the de-velopment of better testing methods for the small operator who has not at his command a staff of metallurgists. Of several tests on samples of varying assay and mineralogical composition, by cyanidation alone, by flotation alone, and, by combinations of the two, the following report was perhaps the most complete and may well serve as a typical example: METALLURGICAL TEST REPORT Silver Mines Co. Semi-oxidized Ore Procedure: Ore ground to 65 mesh, given flotation treat-ment using pine oil and potassium xanthate. Flotation tailing was thickened and given cyaniding agitation in solution strength of 5 lb. cyanide per ton and 2 lb. lime per ton.

Jan 12, 1927

By P Heppner, J Schell, R Newell

The effect of various methods of conditioning on subsequent flotation performance was reviewed, where complex interactions involving attrition, aggregation, dispersion and surface cleaning were discussed. The present study focussed on the influences of standard laboratory cell conditioning, ultrasonic dispersion and high intensity conditioning on copper mineral flotation characteristics. The effect of substituting demineralised water for the WMC plant water was also examined. It was found that higher copper concentrate grades were often obtained using demineralised water, however the use of high intensity conditioning in mill water gave the highest copper recovery and highest flotation rate constant. This process should be considered if copper grade and recovery in this section of the plant drops, especially if the drop is due to surface oxidation of the copper minerals. Other methods of conditioning (cell and ultrasonic techniques) improved the rate of copper flotation above that obtained in the virtual absence of conditioning, showing the importance of conditioning on subsequent flotation operations.

Jan 1, 2000

PLANS for development of the San Manuel ore- body have been worked out and are progressing parallel with construction of the surface plant. This property lies in the Old Hat mining district, Pinal County, Ariz., about a mile south of Tiger where the St. Anthony mine once produced gold, molybdenum, vanadidn, lead, and zinc. Two development shafts have been completed and serve as ingress for preparation of the 1475 haulage level and 1415 grizzly level. Three other shafts are being put down. The Nos. 3A and 3B shafts will provide the ore hoisting facilities. The No. 4 shaft, now being sunk, will be at the main mine service and supply yard, with primary function to provide the mine with supplies.

Jan 7, 1954

By A. Taylor, M. Blanchette, J. Doucet

"A Z1600 Jameson Cell Test Rig was rented for test work at Vale’s Clarabelle Mill operation. This paper discusses the evolution of renting the unit for test purposes to owning the unit and operating it as a revenue generating process component. The paper focuses on three aspects of the Z1600 project; the initial rental and installation, the test work performed in the cleaning circuit, and the business factors which led to the unit being permanently incorporated into the copper circuit.INTRODUCTION Clarabelle Mill is located in Sudbury Ontario (approximately 350 km north of Toronto) on the southwest rim of the Sudbury basin a meteoric impact crater that is 62 km long and 30 km wide. The result of the meteoric impact was concentrated nickel (Ni), copper (Cu) and platinum group metal (PGM) ore bodies in the outer perimeter of the basin; described in more detail by Hanley (1957). Vale currently has seven operating mines in the Sudbury basin, from which nine distinct ore types are mined. Ores are also received from two QuadraFNX mines. Clarabelle Mill processes all of these ores for the Ontario Operations of Vale. The mill, commissioned in 1971, was originally built as one of four mills operated by then Inco Limited. Between the late 70’s and the early 90’s process changes were made to consolidate the Sudbury Operations milling processes into a single operating mill, Clarabelle Mill. In 1990, the SAG mill was installed resulting in peak mill throughput of 11.9 million short tons per annum (Mstpa), with typical throughputs of ~10 Mstpa. Mill average feed grades were 1.4% Cu and 1.2% Ni. During the resources boom, plans were developed to increase the mill capacity at Clarabelle Mill in stages to a final capacity of 13.5 Mstpa. The project known as the Clarabelle Mill Expansion and Recovery Project (CMERP) included expansion and reconfiguration of the grinding and flotation circuits. The first stage was a planned increase in grinding capacity with the reallocation of existing mills, the existing flotation capacity would be required to treat higher throughput until the new flotation circuit was constructed."

Jan 1, 2012

By R. Hogg, T. F. Dumm

With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink-float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are wed as dispersing agents, and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and subsieve particle size analysis of the specific gravity fractions, a complete size-specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as - 10 µm.

Jan 1, 1987

By Rolando Luna B

El presente texto señala las áreas operables y marginales de cada veta trabajada dentro de la mina a través de la limitación rentable y marginal durante y para la operación de la mina. Para ello, se definen algunos conceptos del ámbito minero y se analiza la aplicación de una metodología más adecuada para la operación minera. En esta perspectiva, se busca encontrar áreas adecuadas en cada veta de explotación, cuyo valor de mineral se ubique por encima de tres niveles e involucre elementos de costos diferentes en la operación y administración de una mina. Una vez determinados los costos, se realiza la evaluación práctica de la veta mineral y se define cuáles son las zonas trabajables y no trabajables en función a los precios de los metales, costos geológicos, operativo y las proyecciones futuras de ambos.

Aug 26, 1988

By Charles Clayton

CAST-STEEL runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Foley1 found not only the usual ingot structure, but zones of Widmannstattian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent, nickel and 0.350 per cent. carbon and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. The macrostructure, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregation of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of- the runner and in all parts of the individual grains. I he tipper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to- some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 3, 1920

By A. Becker, J. A. Slankis

Equipment has been developed to utilize natural 8 Hz electromagnetic fields to measure rock resistivities. Telluric and magnetotelluric surveys have detected resistivity variations associated with geological contacts and metallic sulfide deposits. The fundamenfa1 premises of these methods are illustrated by the results of surveys across a Pleistocene-Precambrian contact in the Ottawa Valley and a near-surface sulfide deposit in Northern Quebec. Such interfaces are characterized not only by variations in apparent resistivity, but also, unexpectedly by the spatial anisotropy of the electric fields and the presence of a strong vertical magnetic field component in their vicinity. Standard geophysical electrical and electromagnetic methods (Heiland, 1940) for the determination of the electrical properties of the ground and the search of good electrical conductors necessitate the use of a transmitter and receiver which are coupled galvanically or inductively through the ground. The electrical properties of the ground are deduced from either the transfer function, or the impulse response, of the transmitter — ground — receiver system. Where deep penetration is desired these methods require powerful transmitters whose weight and size increase the cost and reduce the speed of operation. It is possible however, to resort to another class of electrical prospecting methods which employ ambient, natural electromagnetic fields in place of a transmitter.'-' In the audio and subaudio frequency ranges, these fields are generated by thunderstorm activity. At some distance from the seat of the disturbance, the e.m. fields propagate as plane waves with a horizontal magnetic field component. The incident wave, of course, induces currents in the ground. Where the ground is homogeneous the relation between the horizontal magnetic and horizontal electric fields vectors is particularly simple:' /E/ = \[SpT/H/ (1) where: /E/ = magnitude of horizontal electric field in millivolts/kilometer (RMS) /H/ = magnitude of the orthogonal inducing magnetic field in milligammas (RMS) p = rock resistivity in ohm-meters i = frequency of measurement in c/s In practice, the ground is seldom an homogeneous half space, lateral conductivity variations exist, (in the case of base metal prospecting these are the features actually sought) and the two field vectors are no longer simply related. The ratio of E to H is still useful, however, for the determination of an "apparent" ground resistivity. From a theoretical view point, the general problem of a two dimensional fault or dyke anomaly can be separated into two distinct cases. In the first case, where the e.m. energy propagates in a direction normal to the strike, the horizontal magnetic field remains constant and is oriented along the strike of the formation.3 As shown by d'Erceville and Kunetz," all the information about the anomaly is contained in measurements of the electric field component. In fact, away from the interface, the electric fields are proportional to the square roots of the resistivities:

Jan 1, 1970

Six pioneers of the American mining industry will be inducted into the National Mining Hall of Fame on Saturday, Sept. 13, at the Museum Convention Center in Leadville, CO. The 16th annual Mining Hall of Fame induction banquet will begin with a reception and open house at 5:30p.m., followed by the dinner and program at 7 p.m. The six inductees include James M. Gerstley, the only living member, and George O. Argall, Jr.; John F. “Leadville Johnny” Campion; Charles R. Nailler; Edwin N. Pennebaker and Russell L. Wood.

Jan 1, 2003

By J. H. Brophy, J. Wulff, H. W. Hayden

The mickel-activated sintering of tungsten occurs in two stages of densification. A kinetic analysis of the second stage has been based on an appropriate model of the process. As in the first stage, the rate-controlling mechanism for the second stage is also the solution of tungsten in the nickel carrier phase. The transition from the relatively rapid first-stage results from the spherozdization of pores and the initiation of grain growth. Finer grain size due to higher-nickel content leads to more rapid and higher degrees of densification 1 HE sintering of tungsten is accelerated by small additions of nickel, cobalt, and iron.' Experimental evidence in detail has shown that nickel-coated, hydrogen-reduced tungsten powder may be sintered to more than 90 pet of theoretical density at l100o C.2, 3 Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the "solution-precipitation" step postulated when the carrier phase is a liquid,4 although in the Ni-W case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in microstruc-tures at the temperatures under consideration. It has been shown that this stage corresponds to a process which is rate controlled by a phase boundary reaction.3 More recent evidence has been presented5 showing that after the initial rapid stage of sintering, densification continues in the final stage but at a slower rate, although no mechanism for this stage of densification was defined. An analysis of later stages of densification in solid state sintering has been presented,6 but it is not directly applicable in the present case of activated or carrier phase sintering. It is the purpose of this investigation to study the final stage of nickel activated tungsten sintering in greater detail The effect of varying nickel content has been examined, and a possible kinetic mechanism defined. EXPERIMENTAL PROCEDURE AND RESULTS Commercial hydrogen-reduced tungsten powder from Wah-Chmg Corp., having a nominal particle size of1 µ and a B.E.T. specific surface area of 5500 sq. cm per g was mixed with aqueous solutions of hydrated nickel nitrate in proportions sufficient to produce nominal compositions of 0.25, 1, 3, and 5 wt pet Ni. This solution was then evaporated to dry-ness at approximately 150" C for 15 hr. Following evaporation, the resulting powder cake was broken with a mortar and pestle and reduced in hydrogen at 800oC for 1 hr. Following reduction, the powder

Jan 1, 1962

By D J. Brake

The correct specification and then selection of primary or major fans for an underground mine is a critical decision not only in terms of fan capital and operating costs, but also safety and reliability which usually has a major impact on mine production. In addition, fan manufacturers may spend tens of thousands of dollars preparing proposals for a purchase enquiry for primary fans especially where they have complete responsibility for the installation (turnkey projects). There are many good reasons to thoroughly and fairly adjudicate fan tenders. This paper describes the process to achieve this starting with the initial fan specification through to the final award.CITATION:Brake, D J, 2017. Fan specification and tender adjudication for mine ventilation engineers with particular reference to turnkey projects, in Proceedings Australian Mine Vent Conference 2017, pp 245–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Sylvain J. Pirson

The number of seismograph field crews employed in the active survey of potential oil territories is still on the increase, owing to the ever pending threat of a shortage in the supply of crude oil. It is to be expected that for years to come the seismograph will be responsible for discovering many new oil fields, both in wildcat territories and in deeper formations, and that the seismographic campaign will go on unabated. Yet improvements in instrumental design, in the field and interpretative techniques, are brought about year after year, and lead to the reshooting of areas many times surveyed previously. Notwithstanding the experience gained by the past eight years of active work in reflection seismographic surveys, the results given by this method of mapping deep formations have in many instances been at variance with the information subsequently obtained by the drill. To overcome this shortcoming, geophysicists have used closer spacing of the shot points and closer control of the depth points. The method discussed here is being used actively in the Mid-Continent region and endeavors to reduce the interpretation work to a mere mechanical technique, leaving as little as possible to the opinion of the interpreter. The New Method Field Technique.—In sectionized territory where country roads are available every mile, shot points are preferably located every 1/4 mile when six detectors are available or every % mile when eight detectors are at hand. The disposition of individual spreads is represented on Fig. I; in each case a shot point is located at the section corners. Fig. 2a represents the layout of a spread between shot points, the vibration detectors being preferably equidistantly located. Normally in the 1/4-mile control, the distance between shot points is 1320 ft. and the distance between detectors 220 ft. When shooting from shot point S.P. I, detectors 1 to 6 are connected to the recording galvanometers and detector 0 (which indicates the vertical travel time of the wave corre-

Jan 1, 1940

By Hanes J

More than 200 bursts in coal occurred at Leichhardt Colliery prior to December 1978 during mine development in the 6 m thick Gemini seam at depths approximating 400 m. Three large bursts each displaced more than 300 tonnes of coal and stone. Two of these which occurred in continuous miner developments, are described and compared. Geological settings, mining strains including induced cleavage and roof failures associated with bursts are described. A shotfiring technique replaced mechanised mining following a major incident at the colliery. Present mining procedures, the apparent improvement in stability of workings and ongoing geotechnical monitoring programme are discussed.

Jan 1, 1980

By Ann M. Hagni

Microscopic and sub-microscopic gold commonly occurs in the sulfides pyrite (FeS2) and arsenopyrite (FeAsS). To recover refractory gold from pyrite and arsenopyrite, these sulfides are roasted to create porosity and permeability prior to cyanide leaching. A new technique of adding Ca(OH)2 and roasting. lime roasting. is being tested for retention of contaminant sulfur and arsenic and effectiveness of gold extraction. The lime roasting of pyrite at 500°C contains anhydrite (CaS04). oldhamite (CaS). calcium sulfite (CaS03). hematite (Fe2O:J), magnetite (Fe304). and minor amounts of pyrrhotite (Fe1.xS) and pyrite. At 600°C. 650°C and 700°C. the main constituents are anhydrite. oldhamite. and hematite. At 750°C. 800°C. and 850°C. anhydrite and hematite are the predominant phases with minor oldhamite. The roasted arsenopyrite at 450°C contains arsenic sulfides. calcium sulfite. hematite. and minor oldhamite. magnetite. and pyrrhotite. At 650°C. 700°C, 750°C. and 800°C, anhydrite, oldhamite. arsenic sulfides, and hematite are present. At 850°C. the same minerals are present with only minor oldhamite. The textures indicate excellent porosity and permeability at high temperatures. At lower temperatures, rims of low porosity and permeability surround many of the pyrite and arsenopyrite particles, and the complete oxidation process from pyrite to pyrrhotite to magnetite to hematite can be observed in individual particles. Additional process mineralogy techniques employed in this study are electron spectroscopy for chemical analysis (ESCA) and cathodoluminescence microscopy (CIM) in the determination of the calcium-sulfur-oxygen phases. Automated scanning electron microscopy-energy dispersive spectroscopy was utilized to analyze particles for gold content. Reflected light microscopy (RIM) revealed arsenopyrite and pyrite encapsulated in quartz particles of the gold-bearing concentrate, gold roast calcine, and cyanide leach residue.

Jan 1, 1991

By Arthur B. Cummins

POWDERED nonmetallic minerals and rocks of many different types are used extensively in industry for incorporation in compositions and manufactured products The term "mineral filler" is commonly employed to designate a material that is used for a specific purpose but not as an essential or reactive component Such a definition is not without objections, and it is indeed difficult to define fillers in any fully satisfactory manner, since the term has come to have so many different meanings and to cover such a wide range of uses. A filler is defined, for the purposes of this chapter, as a substantially inert material not specifically employed as a reactive or essential component, the primary function of which is to modify the properties or processing of a composition of matter or fabricated article Emery1 has emphasized that fillers change the properties of the product but are themselves unchanged in compounding or use The term "filler" appears to be rather general when referring to usages m bituminous compositions, rubber, composition floorings, fertilizers, plastics, textile finishes, and some others. In paper manufacture, in the paint industry and with insecticides, other terms are frequently employed, as is indicated, herinafter By placing emphasis on the function of the material used in modifying the properties of the composition or article, it is believed that a more useful classification of filler products and their applications may be derived. FUNCTIONS OF MINERAL FILLERS All of the manifold functions of mineral fillers cannot be listed in a summary review. A survey of the uses for these materials, however, shows that in nearly all cases the powders are employed to modify the properties of a composition of matter or those of a fabricated article, or to perform some useful function In the manufacture of either. A generalized list of these useful functions may be given is follows 1 To Modify Optical Properties Color Surface texture Opacity Brightness and gloss (as in paper and plastics) Flatness (as in lacquers and paints)

Jan 1, 1949

NEW MEMBERS The following list comprises the names of those persons who became members during the period Nov. 10 to Dec. 10, 1914: Members ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. ANDERSON, THORVALD J 542 S. Seventh Ave., Mt. Vernon, N. Y. BALFOUR, A. M P. 0. Box 301, Republic, Wash. BOUDWIN, WALKER J., Mech. Engr 159 Pierpont Ave., Salt Lake City, Utah. BRADLEY, LINN, Engr Research Corpn., 63 Wall St., New York, N. Y. BROKAW, ALBERT DUDLEY, Asst. Prof., Min. and Econ. Geol., Univ. of Chicago, Chicago, Ill. BUTLER, PERCIVAL PACE, Asst. Supt., Copper Queen Reduction Wks., Douglas, Ariz. CAJANDER, SVEN G., Mech. Engr Braden Copper .Co., Rancagua, Chile.

Jan 1, 1915

By C. E. Jordan

Abstract. The U.S. Department of the Interior, Bureau of Mines, as part of its effort to maintain an adequate supply of minerals and metals to meet national economic and strategic needs, is conducting research on the pneumatic recovery of coarse mica. A system of crushers, screens, and zigzag air classifiers is used to concentrate coarse liberated mica particles from mica ore and from the waste tailings of abandoned mica operations. The plus 0.21-millimeter-size mica is effectively recovered by this method. The mica concentrates produced contain over 90 percent mica. The method recovered up to 78 percent of the mica in the samples. As a dry concentration method, the pneumatic-beneficiation technique may be advantageous in areas of limited water resource.

Jan 1, 1980