Search Documents

By G. W. McMahon

Following the Sago Mine accident, the U.S. Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 0.3-m (1-ft) resolution map of the mine to produce a 3-dimensional (3 D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3 D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jul 1, 2010

PRECEDING chapters on thermochemistry, and the reactions in and between metal and slag phases in the bath of the furnace tend to emphasize the equilibrium or "static" conditions in the furnace and process, such as the total amounts of heat from fuel combustion or from certain bath reactions, the concentration relationships between slag and metal at the steady state for certain reactions, and the like. Such data are obtained essentially by means of the logic of thermo- dynamics, which helps to determine the energy change between initial and final states in a process as well as to define its equilibrium or steady-state condition, but which is not concerned with the rate of change in the process or with the mechanisms or path followed between initial and final states. These questions of just "how it works" and "how fast" belong to the kinetic aspect of any process; their answers are helpful in speeding up or slowing down and thus controlling intelligently its operation, and also to understand certain natural limitations which are especially important in many high-temperature processes. The kinetic aspects of interest here comprise mainly (1) the flow of gases through the furnace system, (2) the flow of heat in the system, and (3) the mechanisms and rate factors in the various chemical reactions. A really adequate discussion of the first two subjects would require at least three or four times the space available here; it has been tried, therefore, in this and the next chapter to outline but a few fundamentals necessary to an intelligent approach and to indicate some of the conditions of heat and gas flow more or less peculiar to the open hearth, since several good general discussions on these subjects may be found in the literature.(1) For the designer of open-hearth furnaces, the principles of gas flow are of paramount importance.(2,3,4,5) They are also important to the operation of the process, however, at least to the extent of a general qualitative picture of the movement of gases in the system, which is all that is attempted here.

Jan 1, 1944

By Benjamin Smith Lyman

The question of the original extent of the anthracite-beds of Pennsylvania has often been raised; and even discussed with reference to the probability of their present existence under the New Red, a matter of immense practical importance. So high an authority as my revered master, J. P. Lesley, Honorary

Jan 1, 1903

By Elton A. Youngberg

J. H. HEARDING, Jr.*—Extremely hard ferruginous chert (taconite) was encountered in driving a drift at the Fraser underground mine near Chisholm, Minn., on the Mesabi Iron Range. In order to get better results in drilling in this ground, it was decided to try tungsten carbide bits. In the beginning, 1½ in. tungsten carbide bits and 1 1/8 in. round-lugged alloy steel drill rods with "jack-stud" inserts were used. Considerable difficulty was encountered because the jack-stud became loose in the drill rods. Because there was not enough alloy steel drill rod on hand, we began to insert jack-studs in the ordinary high carbon drill rods and found, to our surprise, that there was less trouble with jack-studs working loose in these rods than there had been with the alloy steel rods. As a result, use of the alloy steel rods has been discontinued entirely. Under the heading "Drilling Procedures" the statement is made that all holes are started with detachable bits or conventional steel to prevent undue strain on the tungsten carbide bit inserts when collaring a hole on uneven ground. This practice was followed in our work originally for the same reason. It was soon found, however, that the holes could be started with the tungsten carbide without injuring the inserts if the drill operator was careful and did not give the drill too much air until the bit had a chance to seat itself in the rock. J. C. FRANZ*—In a discussion of other technical papers with reference to percussion drills and the use of carbide tungsten bits, it was my impression that the authors reported one of the first difficulties experienced with the use of standard, conventional percussion drills, was insert bit failures due to crushing of the bit inserts when the bits became dull. During the past few years, some of the rock drill manufacturers, I am told, have adopted an air drill for use with the carbide bits that have a lighter blow and faster rotation than the regular machine. This machine has been tested and the carbide bit failures have been considerably reduced. L. W. DUPUY†—The difficulties Mr. Youngberg mentions that were had with rod and coupling breakage call to mind similar troubles experienced at the Picacho mine in California near Yuma.6 The commercial couplings then available were found to be tempered almost to brittleness. Rod breakage was usually in the threads near the end of the rod. The highly-tempered couplings would break as soon as the rod broke. The solution was to thoroughly anneal the couplings and to put in only a very mild temper. Subsequently the alloy used in making the couplings was changed from the original by the manufacturer, but still only a very mild temper was used. The result was that the softer coupling would give but would not snap and release its hold on the broken rod thread. Fishing jobs were reduced to the few where the rods broke at the rod end of the thread. Thread breakage on the rods was further reduced by thorough annealing prior to tempering. The data Mr. Youngberg presents regarding the use of carbide inserts on long blasthole drilling is most interesting and it would appear that the use in this manner of percussion drills and carbide bits will have many applications. W. M. WOODWARD*—How many feet of hole, on the average, do you get from a tungsten carbide bit, and is there much variation from this average? E. A. YOUNGBERG (author's reply) —In recent months the 2 in. tungsten carbide bit footages in long hole drilling hake varied from 115 .to 140 ft monthly. The footages obtained from individual bits vary from several feet to over 300 ft, however the life of a majority of the bits will be within 25 ft of the average.

Jan 1, 1950

By J. B. Watts

"THE Mine Engineering Department at Gaspe Copper is staffed by a chief engineer, assist-ant engineer, research engineer, chief surveyor, four instrument men, chief bonus clerk, draftsman, and a helper pool of four permanent men plus one or two students in the summer. The men are grouped according to function for organization purposes. Routine services provided by the Mine Engineering Department in-elude ail surface and underground surveying and mapping, preparation of working drawings, compilation of engineering reports, recommendations on ventilation, testing the mine air for carbon monoxide, research on mine equipment and its use, and the calculation of incentive bonus. Demand jobs from departments other than the Mine Department .are done on request. Such jobs may be in the plantsite, the Town of Murdochville, or at the shipping points at Gaspe harbour or the St. Lawrence river."

Jan 1, 1959

Uranium minerals were found in Australia as early as 1869, but it was not until the 1940's that a search specifically for uranium was begun. Instrument types and techniques used in early exploration are still used today, but have been developed into more sophisticated and portable types. Recent improvements in exploration have been the introduction of the gamma ray spectrometer, radon sampling and geochemical surveys. The environments of presently defined uranium deposits are predominantly sedimentary. Known deposits in igneous environments are usually small. The size of targets which are likely to provide economic deposits is of the order of 10,000 tons U308, producible at a cost of less than $10 per pound. Such targets are most likely to be in Precambrian sediments or in granitic masses. Recent exploration in Australia has included investigation of Precambrian sediments, Precambrian and Palaeozoic granites, Mesozoic and Tertiary sediments, Precambrian volcanic rocks and brecciated masses of unknown age. The origin and method of emplacement of uranium in these environments is not well known but there are indications that syngenetic sedimentary processes are important, and volcanic rocks may make a major contribution to the supply of uranium.

Jan 1, 1970

A new departure of unusual importance in Institute annals was in-augurated by the trip of President Philip N. Moore to the Local Sections at Nevada, Southern California, San Francisco, Seattle, Spokane, Montana, Utah, and Colorado. Everywhere the visit of the President was the occasion of an enthusiastic and successful meeting, which is reflected in the account, published under the different Sections in this and other Bulletins. The President also joined the members of the Columbia Section in their visit to Nelson, British Columbia, at the International Mining Convention, which was attended by mining engineers of Canada and the United States. The President of the Canadian Mining Institute, as well as the officers and members of the Western Section also attended this convention. For full particulars we recommend to our readers the ac- count of this very interesting meeting, which is given on another page of this. Bulletin. It is believed that this is the first meeting between the mining engineers of America and any other country since America joined the Allies. The Secretary of the Institute accompanied the President at the first four meetings and was expecting to attend the others also, but was called home by a death in his family.

Jan 7, 1917

By L. L. Oden

The Bureau of Mines has studied a number of processes to remove Cu from molten steel scrap with the objective of determining if any of the laboratory methods studied warranted in depth research investigations. Experimental approaches included oxidizing Cu from steel containing other metals that form stable mixed oxides with Cu (AI, Cr, Fe, Mn, Mo, and V), injecting the same metals as oxides to simplify the mechanism of complex oxide formation, partitioning Cu into alkali or alkaline earth silicate slags or oxide-moderated sulfides, and coremoving Cu and S by injecting active compounds of Ca and Mg. The most promising tests, producing nearly 0.3 pct Cu in the slag, used Ar injection of K20-moderated Na2S-FeS below the surface of molten steel containing about 0.6 pct Cu and protected by a CaO-SiOz slag; however, in depth research investigations currently are not felt to be warranted.

Jan 1, 1987

Electrostatically charged water droplets efficiently suppress breathable dust produced during open air rock crushing operations, according to recently completed independent tests conducted for the Environmental Protection Agency. Since a primary rock crusher produces very heavy clouds of dust, this application was selected as an appropriate test site to measure the efficiencies of new "charged fogging" equipment in mining and mineral processing operations. EPA's Industrial Environmental Research Laboratory, Research Triangle Park, NC, contracted TRC-Environmental Consultants Inc. of Wethersfield, CT, to conduct a full-scale demonstration of a recently developed electrostatic fogger, designed to project a charged fog spray at distances up to 15.2 m. Test results indicated overall fogger efficiencies of approximately 70%. The Fogger IV* employed in these tests is reportedly the largest charged logger ever made, with an extremely long operating range. The original fogger was designed for indoor dust control; this fourth generation version is designed for fugitive dusts, indoor and outdoor, and has an operating range up to 15.2 in.

Jan 6, 1981

By Norman Weiss, H. W. Kaanta

CUSTOM ores reach across the New Mexican mesa to American Smelting & Refining Co.'s new lead-zinc mill at Deming. The influx of ores justified increasing mill capacity from 12,000 tons per month to 20,000 tons per month with the installation of a second milling section. Deming mill has met a complex material handling problem with the successful instrumentation of modern machinery and knowledge. A tight, compact plant does a big job with the aid of the latest ore moving equipment. Location and Layout The mill is located three miles northwest of Deming in the tumbleweed covered valley of the Mimbres River, 30 miles north of the Mexican border. Deming has a population of 4000 and is about halfway between Lordsburg and Las Cruces and 54 miles southeast of Silver City. The AT&SF and the SP railroads and U.S. Highways 70, 80, and 260, cut across the mesa to the town. Asarco mill station is east of the AT&SF single track, and north of Deming. The nearly level terrain is covered with fine sand supporting only yucca and tumbleweed. Compacted gravel at depth affords excellent foundation bearing. The climate is semi-arid, but the district is underlain by water-bearing strata. Tailing disposal space is plentiful. The Deming site appeared favorable because of easy rail and highway access, central location in a mining district, excellent climate, plentiful water supply, space for all present and future requirements, and proximity to a town. The milling plant is a 250-ft square. The rail spur forms the west side; sampling plant, fine-ore conveyor and bins are on the east; track hopper, primary conveyor, and crushing plant lie on the south; and the mill building completes the north side of the square. Construction The mill site was chosen and the land purchased in 1,946 and 1947. Design began in 1948, and Stearns-Roger Mfg. Co. of Denver started construction in June 1949 completing work in April 1950. Construction is steel and concrete throughout, with main concrete floors supported on cellular steel beams. The building is covered by galvanized corrugated iron, attached to the frame by welded Nelson studs, and made dust tight at the joints with roofing paper and asphalt sealing compound. Crushing and Sampling Custom ores, delivered to the mill by railroad cars or trucks, are weighed on arrival. A Robbins car shaker dumps the ore into a 100-ton capacity steel hopper. Adjacent is a 40-ton truck hopper. Three 36-in. Pioneer apron feeders supply ore from the receiving hoppers to a 36-in. conveyor which runs to the crushing plant. A tramp-iron detector protects the primary crusher except when handling magnetite containing ores. A 2 ½ -in. spaced grizzly precedes the primary Traylor 24x36 in. jaw crusher set at 4 in. A Symons 4-ft cone crusher in closed circuit with 48x78 in. Robbins Gyrex screen completes crushing to 5/8 in. The discharges of both crushers drop upon a common conveyor, which, after gaining sufficient elevation, transfers ore to a return conveyor. This return conveyor passes under a suspended magnet and over a magnetic head pulley to the Gyrex screen. Screen undersize is conveyed by a 20-in. belt to the sampling plant. Crushing rate varies from 60 to 90 tons per hour. Ores containing magnetite and pyrrhotite nullify the magnetic detector and overload the magnets

Jan 1, 1952

By Ron Jessulat

"IntroductionBrunswick Mining and Smelting Corp. Ltd. is a IO 500 tid base metal producer. Development is carried out by Jarvis Clark MJM-21 3-boom development jumbos, using Tamrock E400, 410 and 550 pneumatic drills. Typical drift size is 13 ft by 18 ft with a 12-ft advance per round. Blast holes are 1 ½ in. in diameter while reamed holes are 3 in. in diameter. AN/FO is the principal blasting agent, being loaded by C-I-L model60R intermediate loader. The detonators are NONELS and DETINELS. Sulphide dust explosions occur during blasting when dusts from certain minerals such as pyrite and pyrrhotite are ignited by name from the detonating shots. The result is a secondary unwanted explosion with a characteristic shock wave and name front that are very destructive to mine services such as ventilation ducting, electrical cable, and ventilation control doors.A typical reaction in the Brunswick orebody occurs according to the chemical formula:4FeS 2 + IIOs-2Fe2O3 + 8SO2 + 3458--(Enright , 1988)The hematite (FeO3) is deposited as a red dust in the blast area while the toxic sulphur dioxide gas (S00 contaminates the underground workings . The presence of S02 gas disrupts production until it is purged from the area by the mine ventilation system or dissipates slowly in those areas where the vent ducting has been melted by the name front or torn down by the shock wave.Sulphide dust explosions exact a high economic toll. Direct costs in damaged materials and wages are probably exceeded by the value of lost production and disruption to the mining cycle. In addition, the health and safety concerns associated with sulphide dust explosions cannot be ignored."

Jan 1, 1993

By Mahesh C. Jha

Cyanidation has established itself as the main process for extracting gold from ores in this century. However, many ores exhibit refractoriness to the conventional cyanidation process. The main cause of the refractoriness is generally the presence of carbon, tellurium, and sulfides, particularly those of antimony, arsenic, and iron. The problem is usually solved by either modifying the cyanidation conditions or providing an oxidation pretreatment. This paper presents results from studies that help in understanding the causes of refractoriness of various gold ores. This is followed by a discussion of many processes that have been developed to solve the problem such as intensive cyanidation, pressure cyanidation, carbon-in-leach cyanidation, and pretreatment processes such as roasting, chemical oxidation, autoclave oxidation, and bacterial oxidation.

Jan 1, 1986

By Chester A. Fulton

APATITE, the most abundant crystalline phosphate mineral, is found in igneous rocks and probably is the primary origin of all other phosphates, whether mineral or organic. Its chemical formula may be expressed as Ca5(Cl,F) (PO4) 3. The chlorine may be replaced almost entirely by the fluorine. It is found in large or small hexagonal prisms, usually of a vitreous luster and a green or red color, but also violet, white, or yellow. It is found largely as an accessory mineral in granitoid rocks. Its hardness is 4.5 to 5 and its specific gravity is about 3.2. There are many other phosphate minerals-for instance, amblygonite, autonite, collophane, lazulite, monazite, pyromorphite, torbenite, triphylite, turquoise, vivanite, wavellite-with base elements of calcium, magnesium, iron, aluminum, manganese, lead, cerium, lanthanum, lithium, or several of these in combination and with various amounts of water of crystallization. However, these phosphate minerals have but little value save as specimens for mineral collections, the exception perhaps being turquoise. While large deposits of igneous apatite are mined today for the production of fertilizers and chemicals, more than 90 pct of the world phosphate production is derived from secondary apatites, called phosphorites. These calcium (and magnesium, aluminum, and iron) phosphates have been formed in the alteration of sediments by solutions containing phosphoric acid. Such solutions have come from the weathering or leaching of igneous rocks containing apatite, bone deposits of prehistoric animals and marine life, or guano deposits (excreta of birds). These phosphorites are mostly alterations of phosphatic limestones that took place slowly over many years. Whether it is apatite or phosphorite that is being produced, it is known in the trade as "phosphate rock." The sedimentary phosphate deposits are of marine origin. Some, as laid down, were rich in phosphate or have become so by subsequent subaqueous action and have not been further enriched since emergence from the sea. Some were originally phosphatic limestones or marls from which calcium carbonate was dissolved away by waters containing carbon dioxide, in which calcium carbonate is much more soluble than

Jan 1, 1949

By J. B. Goddard

Abstract. Leaching of, uranium in situ from sandstone deposits with ammonium carbonate solution containing: dissolved oxygen occurs rapidly compared with the leaching of the bulk of the sulfur present as FeS2. However because of their high reducing, capacity and their relative abundance, the FeS2 minerals consume; the bulk of the oxidants A pressure leach apparatus was-construtted which permitted the measurement of oxygen consumtion by FeS2. Oxygen consumption by FeS2 is best described by a first-order reaction. The experimental rate constants for various cores are roughly proportional to their FeS2 contents.

Jan 1, 1980

By Rush N. Hosler

This paper was prepared for the purpose of answering some of the many questions as to why, in the construction of Pennsylvania's Coal Mine Schedule Rating Plan, various factors were, or were not, taken into consideration. Much has been written about merit and schedule rating of industrial risks from an actuarial viewpoint, therefore this phase of the question is taken up only so far as may be necessary in presenting the practical application of the plan now in use. Companies writing fire insurance, about 30 years ago, were the first branch of insurance to use schedule rating; the values assigned their items were largely a matter of judgment. In 1913, the Industrial Commission of Wisconsin evolved the first schedule rating plan to be applied to industrial risks under compensation insurance. Pennsylvania, in 1916, with the inception of its Compensation Act, was the first state to apply the principles of schedule rating to coal mines. A definition of the term "schedule rating" submitted by the writer in a brief to the Safety Committee of the United States Coal Commission is as follows: Schedule rating, as applied to compensation insurance, is an instrument to measure the hazard of known causes of accidents to which employees are exposed in industry and thereby determine an insurance rate commensurate with said hazard. It was first applied to Coal Mining in 1916 in Pennsylvania.' In other words, for a mine operator to insure his employees for injury under the Workmen's Compensation Act, it is necessary that he pay a certain premium based on his payroll. If all mines were assessed the same premium, it would be unfair for the mine with low natural hazard, good safety conditions, and good accident experience to pay the same premium as a mine with bad conditions and experience, therefore schedule rating was introduced.2

Jan 1, 1925

By J. H. Parliament

"The 15,000-tpd Similkameen open-pit copper mine, 10 miles south of Princeton, B.C., started production during 1972. The two main ore zones are separated by the deep canyon of the Similkameen River, with the Ingerbelle or western deposit being mined first. The location, design and construction of the plant were complicated by the steep terrain and the situation of the orebodies. Mining, utilizing 10-cu.yd electric shovels and 100-ton electric-wheel trucks, is conventional. Closely integrated with the preproduction mining was the construction of a 4-mile section of main highway to bypass the Ingerbelle pit. This entailed a very large fill, placed with mine equipment. Ore is crushed to minus 9 inches, stockpiled and reclaimed for direct delivery to three 32-ft-diameter by 14• ft single-stage autogenous grinding mills, each driven by two 4000-hp motors. Because of the friable ore in the upper part of the mine, 4-inch balls are added, with higher than design throughput attained. Classification is by 91>-inch spiral classifiers and cyclones. The flotation section comprises three parallel lines of ten 400-cu.ft rougher- scavenger cells and a single line of 100-cu.ft cleaner and recleaner cells. Concentrate is transported in end dump, closed trucks to Vancouver for dockside storage prior to shipment to the smelter. Tailings are piped across the canyon on a suspension bridge and through a tunnel to an empoundment area. Water is reclaimed and returned to the concentrator, forming a closed system. Dams are raised with cycloned ands, with the downstream section compacted."

Jan 1, 1973

1. List of Manuscripts Seen in America 2. List of Manuscripts Seen in England 3. List of Maps Examined 4. List of Newspapers Examined 5. General Bibliography - Numbered Reference List

Jan 1, 1942

ST. LOUIS SECTION H. A. BUEHLER, Chairman, CHARLES T. ORR, Vice-Chairman., THOMAS T. BREWSTER, Vice-Chairman, L. L. HUTCHISON, Vice-Chairman, W. E. McCOURT, Secretary-Treasurer, Washington University, St. Louis. CHARLES J. ADAMI, EUGENE MCAULIFFE, A. C. TERRILL, JAMES A. CASELTON, JAMES D. ROBERTSON. The annual meeting of the St. Louis Section was held at the St. Louis Club, Saturday evening, Mar. 10, 1917. Philip N. Moore, President, and Bradley Stoughton, Secretary of the Institute, were the guests of the Section. The meeting was preceded by a dinner, at which 70 were present, and was presided over by F. W. DeWolf. Addresses were made by Mr. Moore and Mr. Stoughton. The routine reports of the officers were- presented and the Executive Committee named above was elected for the current year. The special business of the meeting was a report of progress concerning the arrangements for the Institute meeting to be held in the St. Louis Section district, Oct. 8 to 13, 1917. The general program for the meeting met with the cordial approval and cooperation of the members of the Section. It was evident that the members are united in an endeavor to arrange a successful meeting. W. E. McCOURT, Secretary.

Jan 4, 1917

By Graham J. C. Carpenter, Marc Charest, Jason Lo

"The method of producing magnesium-based composites with silicon carbide (SiC) particulates embedded in the matrix of magnesium AZ9I D alloy by the squeeze-casting technique are described. This method involves the fabrication of a SiC particulate preform and the subsequent squeezing of molten magnesium into the preform. In this study, alumina, aluminum phosphate and a proprietary binder were used for the fabrication of SiC particulate preforms. The procedures employed in the fabrication of SiC! AZ9ID composites are presented, together with the results of characterization of the composites using optical and transmission electron microscopy. Special attention is given to the reaction products in the bulk alloy and at the interfaces between SiC particles and the AZ9ID matrix alloy.1. IntroductionInterfacial, microstructural and metallurgical characteristics play an important role in determining the mechanical properties of a composite. In theory, reinforcing magnesium with SiC particulates should provide an improvement in strength and modulus of the composite over the unreinforced counterpart. However, many factors resulting from the fabrication process can cause degradation rather than improvements to the mechanical properties. In particular, the interfacial characteristics are known to critically influence the properties of composites [1]. Before evaluating the mechanical properties of a composite, it is always useful to examine the microstructure, which is closely related to the mechanical behavior. This helps to reduce the labor-intensive steps of sample preparation for mechanical property evaluation, which can be particularly difficult as a result of the high hardness of composite materials, as well as providing a wealth of information on the microstructural and interfacial characteristics, particularly the reaction products caused by processing. This information is also pertinent in understanding the factors governing the mechanical properties of the composites.There are many factors which determine the nature of the interfacial characteristics of a SiClMg composites. Qualitative estimations of the interfacial bonding have been performed based on thermodynamics, electronic and electrostatic concepts. In addition, the kinetic conditions during the fabrication play an important role. From an interfacial energy standpoint, the driving force for the formation of a metal/ceramic interface is the decrease in free energy that occurs when intimate contact is established between metal and ceramic surfaces. The simple representation of the energy change per unit area of interface formed (~G) is given by Dupre equation [2]:"

Jan 1, 1996

By Sharon Huamán

El presente trabajo señala y cuestiona el proceso de diagnóstico y evaluación de la generación de Gases de Efecto Invernadero (GEI), y el consumo de energía en las operaciones de Xstrata Tintaya; así como los lineamientos de gestión planteados como consecuencia del diagnóstico para la reducción o compensación de GEI. En este sentido, se muestra la metodología utilizada para la elaboración del inventario de GEI del 2009 realizado en Xstrata y el estudio complementario de eficiencia energética; donde se expone las etapas de elaboración del inventario y las variables que se utilizan para calcular las emisiones de GEI, siendo las principales los factores de emisión establecidos y las metodologías de cálculo de acuerdo al sector y la fuente disponibles. Para ello, fue necesario la recolección de datos de consumo de combustible, energía adquirida, manejo de residuos, gases refrigerantes, etc.

Sep 12, 2011