Search Documents

By Thomas M. Barczak, Joe Bower, Jinsheng Chen

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water-to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water-solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

By F. B. Micheli

Introduction and Historical Background Although both sluices and devices using a simple flowing film are among the oldest known methods of concentration, they are still extensively employed in a variety of situations where they are not only efficient but also have a low operating cost. More particularly, they are valuable for making a bulk concentrate of high specific gravity minerals from alluvials and beach sand and in upgrading low value ores. The antiquity of some of the basic concepts can be seen in the fact that they are found in Agricola's De Re Metallica which was published at Basic in 1546, while in 1602, Carew114 gave a fairly clear account of tin ore dressing in Cornwall in which grass turves were used to catch the cassiterite. This is perhaps one of the forerun¬ners of the blanket strake. The planilla of Mexico, the lanchute of Malaysia and the old Cornish box huddle are also descended from these early strakes. In fact, a sluice with holes in the bottom for concentrate discharge was shown by Agricola, not unlike the principle used in the plane table and the lamflo sluice. The convex huddle for the treatment of sandy material appeared about 1848 and the concave form eight to ten years later. For the treatment of "slime" sizes, wooden dead frames which were manually worked were used in Cornwall for many years but gave way to the automatic water-operated type in 1860, and even a mechanically tilted frame was described by Henderson115 in 1857. Theoretical Considerations The behavior of solid particles in suspension depends to a great extent upon the pulp density and the size of the suspended particles. In a fairly dilute suspension, such as that normally used when dealing with small particle sizes, the behavior of particles in a flowing film results from two effects. These are the lateral displacement, which is determined by the time taken for each particle to penetrate the flowing film and reach the solid surface, and the resistance offered by each particle to further displacement after it has reached this surface. The initial penetration through the flowing film depends on the size and specific gravity of the particle and the thickness and viscosity of the film. As a result the smaller particles will migrate further before their movement is retarded relative to larger particles of the same specific gravity. The behavior on reaching the solid surface de¬pends on whether there is a single particle layer or, as is more often the case, a multiple layer or thin bed of material which is sufficiently dilated, permits the penetration of higher specific gravity grains. Thrust of Flowing Films. When a thin film of liquid flows over a plane solid surface, the layer next to the surface remains at rest but the velocity of the film increases with the distance from the surface and becomes a maximum near, but not quite at, the free surface. Therefore, a particle in suspension in such a film is acted upon by a greater force near the upper part of the film than at the lower part, resulting in an overturning effect. After a particle reaches the separating surface or an accumulated densely packed bed of other particles, the liquid flow causes it to move downstream by rolling, sliding, or by a movement involving alternating suspension and deposi¬tion (saltation). In rolling and sliding, which are brought about by a substantially noneddying stream, the large submerged particles are acted upon to the greatest extent and they move more rapidly than smaller ones, notwithstanding their greater mass. When two particles of the same size but of different specific gravity are considered, the higher density one moves more slowly by reason of its greater mass. As a result the particles tend to become arranged in the manner shown in Fig. 29. If any particle is so large as to stand above the water surface, the transporting force on such a particle, although the maximum available, will have less effect than that on a submerged one. Such large grains are therefore carried a lesser distance. Fluid Velocity in a Flowing Film It can be shown that if y is the distance within the flowing film from the interface, the fluid velocity v' at this point is given by IIn this equation p' is the fluid density, g the acceleration due to gravity, a the viscosity, a the angle made by the film to the horizontal, and 0 the film thickness (in cgs units). Furthermore, the volume Q of fluid per unit time and unit width is related to the film thickness and can be calculated, since which upon integration gives Consideration of the velocity v' (Eq. l) and the terminal falling velocity µ derived from Stokes law enables the horizontal travel dz in time dt to be calculated as follows: Again integration and substitution of Eq. 3 gives In this equation, z is the distance travelled before a particle of density p at the top of the fluid film has settled on the concentrating surface. From these expressions it can be seen that the depth of the flowing film varies as the cube root of the volume of fluid and inversely as the cube root of the sine of the plane surface inclination. Similarly the distance a particle can travel before reaching the surface is directly related to the quantity of fluid and its viscosity. The viscosity of pulp is greatly increased by the presence of near colloidal particles and consequently the penetration of the somewhat larger grains through the flowing film is retarded, resulting in them being carried further across the concentrator deck. Obviously this effect can be reduced by prior removal of some or all of the ultra¬fine particles. The detrimental effect of kaolin on the separation of fine ferrosilicon from quartz has also been demonstrated by Johnston,116 the relationship between viscosity and efficiency of separation being shown in Fig. 30. The pH value also has a very marked influence on the viscosity and the use of acid mine water, for example, can increase viscosity materially and thereby result in lower efficiency. Dilation of Multi-Particle Systems Except during washing (when a single particle layer may exist) concentration usually takes place in a bed of particles which is partially dilated or stirred by eddy currents. The extreme case is seen in various forms of the sluice where the flow of water and the presence of riffles combine to create a fluid bed in which reverse classification takes

Jan 1, 1985

By Clarence S. Ross

INTRODUCTION THIS chapter on the rô1e of physical-chemical processes in ore deposition presents unusual difficulties because it attempts to discuss the theory of processes that are very imperfectly under- stood, but which are among the most fundamental problems now before the student of ore formation. It is generally believed that a great variety of ore deposits are in some way derived from igneous rocks; but we desire to know the mechanism of their splitting off from the parent magma, the physical and chemical character of the material that acts as a medium for transfer from magma to the point of deposition, the manner of deposition, and the methods of replacement and removal of the invaded rocks. This problem is difficult for the field geologist because it concerns forces that for the most part have long since ceased to act. It involves a complex system of which the time for completion extends from the first development of the parent magma through its intrusion, its slow cooling and crystallization, and the final escape of its last residuum, a time probably represented by millions of years. In space the processes extend from profound depths of the abyssal magma which can never be directly observed, through the horizons characterizing deep-seated igneous rocks and ore deposits; those formed at moderate depths; and ends with surficial ones and surface thermal springs. The geologist usually can study the effect at but one of these horizons: he must attempt to fit his puzzle together while seeing but a few parts at a time. Thus he must deal with many isolated phenomena, as if they were the result of many physical and chemical systems; when in fact his problem involves a single exceedingly complex system, and will only be understood when that entire complex system is understood. The geophysicist is handicapped because he must attempt to interpret an extraordinary complex system, involving physical and chemical conditions which he can never hope to duplicate fully, through the study of many exceedingly simple systems.

Jan 1, 1933

By V. F. Hollister

The Queen Charlotte gold deposit (also known as the Specogna, Babe, or Cinola) was discovered in late 1970 by Efrem Specogna and Johnny Trico. They were prospecting along the trace of the Sandspit fault, and they sampled jarositic material that included veins from the fault zone. Their assays included some good gold values. They located the Babe Claims in 1971 and optioned them to Kennco Explorations Ltd. Kennco conducted stream sediment and soil geochem studies, geological mapping and drilling of 55.2 m (181 ft) in two drill holes. Kennco withdrew from the property, and by 1977, Cominco, Placer Development, Silver Standard, and Quintana Minerals had each successively worked on the deposit. Consolidated Cinola Mines bought the claims in 1977 and completed exploration of the deposit ultimately in a joint venture arrangement with Energy Reserves. Energy Reserves entered in late 1979, and by 1983, a total of 200 surface and 12 underground drill holes had been completed, totaling 28 600 m (93,832 ft). In addition, a 461.9 m (1515 ft) adit was driven in the ore body. Reserves published by Cinola aggregate 34 Mt (37 million st) of 1.7 g (0.060 oz) Au per tonne. All industry geologists working in the area agree that the Queen Charlotte gold is an epithermal gold deposit in porous volcaniclastic and clastic rocks that is genetically related to a Miocene-Pliocene rhyolite plug. The geologic description here follows the oral presentation made by G. G. Richards, J. S. Christie, and M. R. Wolfhard at a 1976 CIM meeting. Additional comments by the late C. S. Ney of Kennco Explorations are included with the Richards, Christie, and Wolfhard data to complete the geologic set- ting. The attached reprint by Champigny and Sinclair (1 980) provides additional data on the deposit. The Queen Charlotte (Babe, Specogna, or Cinola) gold deposit is located on Graham Island in the northern Charlotte Islands, at the fault boundary of the Skidegate plateau and the Charlotte lowlands. The Sandspit fault marks the physiographic boundary, and it is intruded by rhyolite porphyry at the deposit. Because displaced geochem anomalies, drain- age patterns, and topography suggest dextral and east side down movement for the fault, exposed east block rocks are younger than rocks west of the fault. The east block, which included the ore deposit, is a lowland largely masked by unconsolidated Pleistocene and Recent clastic rocks. Rocks west of the rhyolite plug, on the Skidegate plateau, are Cretaceous carbonaceous and calcareous shale unconformably overlain by a thin veneer of rhyolite tuff. The deposit is about 100 m (328 ft) above sea level. GEOLOGIC SETTING At the ore deposit, the Sandspit fault is a complex structure. However, lithologies on either side of the fault-controlled rhyolite porphyry plug are distinct. West of the rhyolite, the upper member of the Cretaceous Haida formation shale is the most common rock type. The member is composed of dark grey to black, poorly consolidated, and thinly bedded carbonaceous and calcareous shale. The sequence is silicified to an argillite or a hornfels near the rhyolite. West of the rhyolite porphyry plug, but not importantly involved in the mineralization, is a thin masking cover of rhyolite tuff. The tuff unconformably succeeds the cretaceous shale, but it is largely eroded in the mine area. East of the fault-controlled rhyolite porphyry plug is a thick section of conglomerate and sandstone of the Miocene- Pliocene Skonun formation. The ore body occurs within the coarse clastics, the rhyolite intrusive as the western boundary. Ore is entirely contained within the clastics. Original permeability of the clastic rocks was a major control for ore deposition and alteration, and for that reason, the Skonun formation is described in greater detail. The Skonun formation clastics unconformably overlie Haida shale. The Skonun is at least 300 m (984 ft) thick in the mine area, where it trends northerly and dips easterly 15º to 25º. The sequence is about 62 percent conglomerate, 3 1 percent coarse arkosic sandstone, and 7 percent interbedded siltstone and sandstone. Contacts between adjacent beds are generally sharp. Stratigraphic correlations between drill

Jan 1, 1985

Jan 7, 1976

By K. Thirumalai

Although the term "spalling" has long been known, Norton l first referred to its usage for the fracture or disintegration of materials subjected to rapid temperature changes. Spalling of ceramic materials at high temperatures has received attention in the past.2-4 Removal of the char formed during ablation in reentry of space vehicles has been referred to as mechanical spalling.5 The first experiments to evaluate the process of rock fragmentation by thermal spalling were conducted by Stoces6 using a series of gasoline burners on the quartz veins of the Zinnwald deep mines in Germany. After the development of rocket-jet burners, the principles of thermal spalling combined with high fluid momentum found wide practical application in rocks. The well-known jet piercing process for drilling blastholes in taconite and for jet channeling in the quarrying of granite are among the more notable of these application.7 For the purposes of this study, thermal spalling or spallation of rocks is defined as progressive failure caused by thermal stresses induced by a sudden application of heat from a high temperature heat source. Gray observes that the size of the spall is dependent on the pattern of induced thermal stresses before failure. The spallability or the relative susceptibility of rocks to failure by thermal spalling is a complex but potentially useful parameter for qualitative comparisons. Fundamental differences exist in the degree of spallability among different types of rocks. Accurate prediction of spallability of any particular rock has so far not been possible. Measurement of the state of stress and temperature in the rock during the rapid thermal spalling process poses difficult problems that must be solved. Identifying the parameters that influence the thermal spalling proc-

Jan 1, 1970

CONTENTSSummaryIntroductionGeographical and Geological Outline of the RegionGrowth of the Mining IndustryTable 1: Production StatisticsGeneral GeologyRecent Alluvium and River GravelsSambeto SeriesMudstone and Basalt ContactVatukoula SeriesIntrusivesStructureGeologic HistoryLodesTable 2: Principal Lodes and Their OrebodiesMineral Assemblage and ParagenesisOre Shoots and Their ControlEmperor MineLoloma MineDolphin MineExplorationConclusionAcknowledgmentReferencesSUMMARYThe Tavua Goldfield was found in 1932 within a basin, both topographical and structural, near the sea on the north side of Viti Levu, Fiji, and has produced over £13,000,000 (Fijian) worth of gold and silver from the three mines...

Jan 1, 1953

By Alexander Anderson

In many oil fields a great variation in the production of adjoining wells has long been observed, and a certain proportion of dry holes, situated between prolific producers, has been regarded as normal without thorough investigation as to cause. Similarly, an occasional prolific producer has been found in a part of a field where all other holes have proven disappointing. Adjoining wells which showed an unreasonable difference in production have been surveyed, and the bottom of the poorest producer has been found to have lost sufficient vertical depth, through its drift, to diminish seriously its penetration in the oil zone. Again, the bottom of the good producer has been found to he more favorably situated by its migration up structure. Surveying of wells in California fields has shown many instances where the dry hole has drifted far off the structure to such a degree that no amount of deepening could ever convert it into an oil well. In other cases, edge wells have been found to drift into the field. At this time, in California, the surveying of oil wells is beginning to he accepted as a routine part of operating procedure. Some operators are surveying all of their new wells and, in some of the recently discovered fields, this practice is providing invaluable assistance in methodical development. The information that has been obtained from the surveying of many wells has convinced most operators that it pays to give careful attention to the drilling of wells. Chews are now usually cautioned to avoid reckless competition with each other. Whereas, formerly, certain companies demanded a large footage from their drillers, they now issue orders that a very moderate speed in drilling shall he maintained and that every care be taken to avoid practices likely to cause excessive deviation of the hole frorn vertical. As a result of these new instructions to drilling crews, a distinct decline in the average drift of the wells drilled by these operators has taken place and fewer dry holes are being drilled from good locations. To the petroleum engineer and the geologist, oil-well surveys provide the necessary data required for the construction of the correct cross-

Jan 1, 1929

By D Landriault, G W. Wilson, L Langetine and

Engineered soil covers are used for final closure options for both waste rock and tailings disposal facilities. Currently, cover construction requires excavation of appropriate cover material from a nearby site. If no suitable materials are available, the mine operation may have to ship appropriate materials long distances to the site before the construction of the cover can even begin. This has led to the proposal to engineer cover materials using existing waste materials from the mining operation. The paper presented here describes the results of a laboratory scale testing program to evaluate the potential for blending waste rock, smelter slag and tailings for the creation of a suitable cover material at a site in Canada. Tailings from the local mill, waste rock and slag were collected in the field and blended to create a material with an air entry value similar to the tailings and with physical strength similar to the waste rock. Testing indicated this mixed material could be blended at a consistency of a paste and was suitable for pumping. It can also be compacted to a high-density material. The preliminary results show that it may be possible to blend waste rock, slag and tailings into a material that can be utilised in the construction of a water retaining cover.

Jan 1, 2003

By G. Schubert, H. Hoberg

A large number of diverse size reduction machines is currently available for the comminution of waste materials. Equipment selection is determined by the nature of the material to be treated and by its behavior under external mechanical stressing. Accordingly, wastes can be divided into those with elastictbrittle and those with ductile/viscous behavior. The scientific understanding of the comminution of wastes is lagging strongly as compared to that of the grain-shaped mineral raw materials. Only in a few unique cases have the fundamentals of the comminution of ductile or viscous materials been presented. The paper centers on a characterization and systematic analysis of the types of stress fundamental to comminution. On the basis of this discussion an overview is presented of the currently available technologies for the comminution of wastes, with attention centering on those machines designed for materials with ductile or viscous behavior.

Jan 1, 1998

By C. E. Shoenfelt

Wildcat drilling operations in Utah in 1937 added nothing of importance to the commercial oil and gas possibilities of the state, and such operations consisted largely of efforts to reach objectives in wells started in former years. The Standard Oil Company of California, jointly with the Continental Oil Co., completed a wildcat well in sec. 22, 23 S., 11 E., on the San Rafael swell in Emery County, which was abandoned in metamorphic rocks at 4900 ft.; it tested the Pennsylvanian and Mississippian sections and probably ended in Devonian or older rocks. The Utah Southern Oil Company's test of the Cisco structure in sec. 33, 22 S., 22 E., was abandoned at 6715 ft.; it may have been through the Pennsylvanian section at this depth. The Mountain Fuel Supply Co. continued the development of its Clay Basin gas field, and with the completion of two wells in 1937 added 35,571,000 cu. ft. initial daily gas capacity to its reserves. This company constructed 21 miles of 10-in. gas pipe line from the Clay Basin field to its South Baxter Basin terminal in Wyoming, and during the closing months of 1937 delivered 2,225,000,000 cu. ft. of gas through the Salt Lake trunk line.

Jan 1, 1938

By José Fernandes De Oliveira Ugarte

El presente texto tiene como objetivo la evaluación del oro nativo y electrum encontrado en su forma libre, diseminado, encapsulado en matrices sulfurosas y sulfatadas que fue empleado en los procesos de flotación y lixiviación. Para ello, se estudiaron 54 muestras que fueron analizadas por difracción de rayos X y clasificadas en tres grupos con 18 muestras cada uno e identificadas de matrices oxidada, sulfatada y sulfurosa. Después de tamizadas fueron colocadas en briquetas de 4 mm de diámetro y analizadas por microscopía electrónica para los estudios estadísticos de los minerales portadores de oro y para los estudios de microscopía óptica.

Nov 1, 2015

By Richard H. De Voto

The McDonald Gold Project and two satellite gold deposits near Lincoln, Montana, contain at least 9.9 million ounces of gold and 30 million ounces of silver. The McDonald gold deposit alone contains 7.2 million ounces of gold reserves that can be open-pit mined and processed by cyanide heap leaching at a projected cash operating cost of $190 per ounce. The deposit is predominantly oxidized with no chance of acid production, and can be mined, operated, and reclaimed with minimal permanent environmental disturbance other than the creation of an open pit filled with a fresh-water lake which would support trout. The Seven-Up Pete Joint Venture, the owner of the McDonald Gold Project, commenced permitting of an open-pit, heap-leach operation in November 1994. In 1998, Montana citizens passed an anti-cyanide, open-pit mining initiative, 1-137, which banned any new open-pit gold mine which uses cyanide processing, The Venture has conducted extensive studies, including metallurgical testing of the treatability of McDonald ores with alternative lixiviants, and has determined that all other mining and metallurgical treatment systems are vastly uneconomical in the recovery of gold and silver from the McDonald deposit. Therefore, the Venture's proposed open-pit mining and cyanide heap-leach processing is the only technology that can be applied economically to the McDonald deposit. Further, the analyses convincingly demonstrate that the proposed open-pit, cyanide heap leaching technology results in maximum resource conservation of this valuable and unique deposit and poses far less risk to human health and the environment than any of the alternative technologies.

Jan 1, 1998

By Osamu Takeda

A decomposition process for PCBs by using basic molten salts as a reaction field was investigated in order to establish a safe, simple and highly efficient decomposition process for polychlorobiphenyls (PCBs). PCB containing chlorine (e.g. 2, 2?, 4, 4?-tetrachlorobiphenyl) dissolved in n-nonane solution was supplied into basic molten salts (NaOH-Na2CO3 or KOH-K2CO3) maintained at 500-700 ?C together with the carrier gas (N2-21% O2) through an injection tube. The injected PCBs in a bubble are decomposed by the reaction with the molten salts and oxygen during rise in the molten salts. The decomposition efficiency of PCBs increased with increasing temperature and was achieved to be higher than 99.995% in a certain condition. From a series of systematic study, the effectiveness of the decomposition process for PCBs by using molten salts was demonstrated.

Jan 1, 2008

By Ezra L. Kotzin

Foundry sands used to make molds and cores have been very important to foundrymen since metal casting began hundreds of years ago. They are now used in two basic ways, either in an uncured green state, grain-bonded with clay, or in a set cured state achieved with sand that, mixed with resins or oils, is cured by baking or by chemical reaction. The term sand, as generally used in foundry applications, may best be defined as material composed of granular particles of mineral matter, ranging in size from 0.5 to 2 mm in diameter. The particulate nature of the material may be the result of natural disaggregation or result from crushing and screening of rock or ceramic materials; crushed and screened products are sometimes referred to as "manufactured sand." Based on their origin, the raw materials for foundry sands will vary in grain shape, grain composition, relative surface, grain size, and grain distribution patterns. These properties, in addition to their chemical analyses, sintering point and expansion characteristics play an important part in the choice of sands used as the base molding or core aggregate in metal casting. Sands with different origins may be blended to produce specific compositions and grain size distributions. Early raw material requirements based on silica sand were simple, but as sand/core/mold technology became more sophisticated and binder technology continued to be developed, the physical properties of foundry sands became more critical. Silica sand is composed of quartz, along with, in most cases, small amounts of feldspar, mica, clay, and other common minerals. Although silica sand is still by far the most widely used base material in production of molds and cores used in metal casting, other natural mineral sands have their own unique characteristics and fill an important niche in special applications. As a result, the term sand, as applied to raw materials used in metal casting, has been logically extended to include granular materials composed of a group of minerals other than quartz. With increased use in advanced foundry technology, natural sands composed predominantly of zircon, chromite, staurolite, or aluminum silicate minerals and of granularized chromite or olivine, have become more than just alternate materials and are now commonly classified as sands when the grains are sand-sized. Foundry sand may therefore be considered under two categories: silica sands and non-silica sands.

Jan 1, 1994

By Paul D. Conatore

INTRODUCTION There are important reasons for a discussion of tungsten resources, reserves, and production in the Circum-Pacific area. First, the world's chief tungsten deposits, as well as most of the world's tungsten reserves and production, occur in this region. It is well known that the world's largest tungsten reserves are located in southeastern China and that for many years, the largest individual mine in the world was there. Although China still has the world's greatest tungsten production, the very high-grade scheelite mine of Canada Tungsten Mining Corporation in the Northwest Territories is the largest producer of tungsten today. There is certainly a great quantity of tungsten in Asia, but the strategic importance of this fact is now offset by the wide distribution of mines and production facilities throughout the world, especially in other parts of the Circum-Pacific area such as Australia, Canada, and the United States. In addition, much of the Circum-Pacific area is comprised of Mesozoic-Cenozoic orogenic belts. These global tectonic units are regarded as very favorable for additional tungsten deposits, particularly scheelite-bearing tactites, and consequently, prospecting and exploration will most likely be concentrated in the Circum-Pacific area. Second, tungsten must be regarded as one of the, most important metals of modern industry because of its very special properties. It has the highest melting point, the highest tensile strength at elevated temperatures, and the smallest compressibility of any metal. The metal also possesses a very high density, excellent corrosion resistance, good thermal and electrical conductivity, and a low coefficient of expansion. As a result, tungsten has found increasing importance in a wide range of industries. From the filament in an electric lamp, to cutting tools and drilling bits, to the exotic radiation shields that protect supersonic aircraft and spacecraft, tungsten plays an indispensable role in our daily lives. The primary objective of this paper is to present an overview of important facets of known and suspected tungsten in the Circum-Pacific area. Resources, reserves, current production, planned capacity expansions, and new operations, as well as an assessment of the probability for development of deposits in the Circum-Pacific area, are discussed. RESOURCES The average crustal abundance of tungsten has been estimated at 0.0015 kilograms per tonne. A comparison of the abundance of various metals in crustal rocks to that of tungsten is presented in Table 1, which shows that tungsten abundance is similar to that of its commonly associated metals, tin and molybdenum. Table 1. AVERAGE CRUSTAL ABUNDANCE OF VARIOUS METALS (Grams per Tonne) [ ] With careful thought, it can be realized that tungsten ore deposits result from the concentration of the metal, through normal geologic processes, to levels substantially greater than its average crustal abundance. The minimum technologically and economically workable tungsten concentration, or cutoff grade, is a function of (1) deposit tonnage, (2) mining and milling methods, (3) production tonnage, (4) capital and operating costs, (5) tungsten market conditions, and (6) value of associated recoverable metals. The tungsten cutoff grade that is currently exploitable at a profit varies from 0.09% W03 to 1.55% W03, reflecting concentration factors from 470 to 8200, as shown in Table 2. Table 2. CURRENT TUNGSTEN CUTOFF GRADES [ ]

Jan 1, 1982

By A. B. Barlow, D. H. Pitcher

"The Geophysics/Geochemistry Section of the Ontario Geological Survey initiated an aerial geophysical survey in the James Bay Lowlands, Cretaceous Basin area, District of Cochrane, Ontario. The survey was contracted to Scintrex Limited and was carried out in 1978. Approximately 8000 line kilometres of airborne electromagnetic and magnetic data were recorded. The Tridem airborne electromagnetic system was employed, mounted in a twin-engined PB Y Canso aircraft. This specific Tridem system uses a vertical coaxial coil configuration and measures in-phase and quadrature components of the secondary field at 500, 2000 and 8000 Hz.The primary purpose of this survey was to map subsurface conductivities and, in particular, to search for lignite deposits. Physical property measurements show that electrical methods should detect differen ces in conductivity between the moderately conducting clay-lignite horizons and the less conducting clay, soil, muskeg and gravel horizons. A preliminary Tridem test survey, as well as surface DC resistivity soundings, confirmed this approach. The interpretation of the present survey data indicates that Tridem is a suitable electrical method to aid lignite exploration in the James Bay Lowlands."

Jan 1, 1980

By Freeman C, Dingley W

Addition of sodium nitrite-borax, sodium hydroxide, sodIUm carbonate, lime, or sodium silicate reduced wear of forged steel balls and cast iron slugs in wet grinding a complex zinc-lead-copper sulphide ore in laboratory ball mills. Maximum wear reductions were 27 per cent (forged steel balls) and 33 per cent (cast iron slugs) with sodium hydroxide and nitrite-borax additives respectively.Potential measurements of balls and slugs during grinding, and analysis of the data in terms of corrosion theory demonstrated that corrosive wear had been reduced or prevented by these additives. Actual per cent wear reductions were not equated to the rate of corrosive wear because of the undefined interdependence between abrasion and corrosion in wear processes. The investigation verifies that in laboratory ball mills corrosion is significant in the wear of grinding media and wear can be reduced by corrosion inhibition and pH adjustment.

Jan 1, 1978

By M. Adnan Goksel

A blast furnace test of approximately 5,000 tons of PelleTech Corporation (PTC) cold bond pellets was successfully run at Kaiser Steel Corporation (Kaiser) Steel Manufacturing Division at Fontana, California. The pellets were produced from mill scale, BOF dust and blast furnace flue dust. A 15 day base period, during which time the metallic burden was 2/3 heat indurated pellets and 1/3 sinter, preceeded the test. During the test period the metallic bur- den was 10% cold bond pellets, 56.7% heat indurated pellets and 33.3% sinter. A 15 day post test base period followed during which the PTC pellets were replaced by conventional pellets. The pellets were produced in the 3.C Semi-works Facility located on Kaiser property. The facility incorporates the Michigan Technological University Hydro-Thermal Agglomerating Process.

Jan 1, 1979

By E. T. Laker, John C. Loretto

This chapter deals with the process piping aspects of moving slurries in mineral processing plants and the transportation of slurries such as tailings and concentrates over longer distances. The basic data required to select the process piping is given together with an example of line sizing and material selection. Alternative piping materials are discussed together with pumps and pumpbox design and the types of valves and other fittings available to the process piping designer. The long distance transportation of slurries is briefly discussed and a number of references given on this, including papers on actual installations.

Jan 1, 1978