Search Documents

By Jasper D. Ward

The Indiana Limestone Company has developed an insulated, thin and comparatively light-weight pane 1 suitable for use as a spandrel panel in a curtain wall. The panel is about four inches thick and is composed of limestone backed with insulation. The inner surface of the insulation is protected with asbestos-cement board or a metal pan, depending on the type of insulation, building-code requirements and appearance (if the surface is left exposed). The limestone is cut to the size of the spandrel openings and the insulation and backup is applied in the mill ready to be shipped and in- stalled in the wall grid, A mortarless and waterproof joint with the metal frame components is achieved through the use of neoprene, thiokol, and caulking, The limestone is "dirt-proofed" (waterproofed) in the mill to slow down discoloration. The panel weighs more than some presently used materials. However, ILCO's architects and engineers have found that curtain wall systems capable of withstanding imposed wind loads are made up of sections large enough to carry this extra load of stone with little or no modification to the size of the metal frame. Limestone, a traditionally sound material, can be used in this new way without losing any of its natural qualities of dimensional stability, resistance to fire, and permanence.

Jan 1, 1959

By W. R. Ingalls

WHEN I was a boy, political economy was taught in the old fashioned New England high school that I attended. I still possess my text-book, an abridgment of one of the old classics, and, I referred to it a few days ago. It began with the definition that "political economy is the science which investigates the' nature of wealth, and the laws which govern its production, exchange and distribution." That definition of 50 years ago strikes me still as being a good one. In college I sat under Francis A. Walker, the greatest of American economists. I still have his old text-book, which begins with substantially the same definition as Fawcett, but adds that "political economy has to do with no other subject, whatever, than wealth." As so developed economics was a dry study which captivated but few. It was characterized as the dismal science. It seemed to lead nowhither. . This was perhaps due to the inadequacy of the data available to economists. Consequently, their discussions and deduc-tions were founded largely on conjecture and assump-tions. Naturally this resulted in differences in the formulation of doctrines. There were controversies respecting the nature and influences of money, over the derivation of wages, over the principles of laissez faire (letting things take their own course) over the Malthusian doctrine, and so forth. Amid all this there was one great fundamental law universally recognized, namely the law of supply and demand, which ranks with the law of gravitation and the law of the conservation of energy among the great fundamen-tal laws of nature. The law of supply and demand is the one thing in economics upon which we may fix our eyes as upon the lode star. In the course of time we have fallen out of agreement with Walker's doctrine that political economy has to do with no other subject than wealth. Although it is indeed the science of the production and distribution of wealth we can see that many things pertain to that subject and that economics links hands closely with engineering, biology, and psychology. It is probably the recognition of this that caused the study and exposi-tion of economics to acquire such a strong sociological

Jan 6, 1923

By A. H. Dierker

NEXT to the metal itself, molding sand is the most important raw material used in the manufacture of steel castings. There are no accurate, figures available but probably it would be safe to say that the average steel foundry uses approximately 1000 lb. of new molding sand per ton of castings produced. With untreated sands costing from two to four dollars (in some extreme cases it may run as high as eight or ten dollars) per ton delivered at the foundry siding, molding sand is an important item in the cost of making castings, and any information that may help to reduce this sand consumption should be of interest to the industry.

Jan 1, 1929

By Paul Clayton

Case Study ? Site: BMA Saragi Coal Mine Queensland Australia ? Model: Marion 8050 ? YOM: Mid 1970s ? Boom: 97M ? Bucket: Original capacity of 100 Tonnes upgraded to 125 tonnes at time of filtration upgrade. ? Apps: Swing, Hoist & Drag Gearboxes ? Oil: Oil Castrol Alpha TT1200 Viscosity of 1208 cSt @ 40° C (104° F) 720ltr Oil Volume Trial and Installation Justifications ? To reduce gearbox overhauls. Typical schedule being 5 years. ? Bucket upgrade from 100 tonnes to 125 tonnes. Increased gearbox demand and stress. ? Increase of overhauls out to 10 years + ? Saving per Dragline estimated to be US$8-10M in downtime and maintenance if successful. ? In compliance with BHPBilliton Global Maintenance FLAC program ? Fuels, Lubricants, Air and Coolants ? Cost Justification ? Downtime: 4 days ? Lost production: $420,000 ? Cost of parts: $162,000 ? Labour and misc: $41,000 Gearbox failure cost $623,000

May 1, 2008

By Charles H. Jones

Jan 1, 1905

By T. Seldenrath

In the development of a fluid -operated hammer drill' for accelerated penetration of hard rock formations in oil wells, a research investigation was conducted to evaluate the percussion effects obtained with different design characteristics and to determine the possibilities of percussion in the low frequency range. Tests were conducted on granite blocks and comparable impact forces were measured with a load cell under selected test conditions. These full-scale laboratory tests provided an evaluation of the effectiveness of percussion which was further supported by actual downhole field performance. While much pertinent data have been presented by other investigators the method of evaluation described in this article resulted in good correlation between laboratory and field performance and may be applicable in other low frequency percussion developments. EXPERIMENTAL METHOD For these tests the bit was held stationary and the test block was rotated and forced upward against the bit by a hydraulically-lifted rotary table. "Weight on bit" was calculated from pressure readings on the fluid system of the lifting cylinders—corrected for tare and friction. Percussion was obtained with several tubular hammers of different weights up to 320 lb. These were lifted mechanically and allowed to drop by gravity from various heights onto a slidably-mounted bit sub or "floating anvil" for calibration of the load cell response with known kinetic energy of the hammers. During evaluation of percussion effects, the hammers were hydraulically operated to provide a range of percussion frequencies up to 1,020 blows per minute delivered to the anvil. To obtain comparable test readings, the load cell of the strain gauge type, was attached to the bottom of the anvil or bit sub in place of the bit. The load cell rested on a typical granite test block mounted on the drilling table. The latter was hydraulically supported as in the actual drilling operation. The effect of support resistance was the same for all tools when calibrating. Impact forces so determined werethusdirectly comparable with one another for the purposes of this investigation. When a roller bit was substituted for the load cell for actual drilling, the impact force would probably be reduced due to the resiliency of the bit body, legs. cones and teeth and the penetration of the teeth into the rock. However, since the bits and rock specimens were uniform in these tests, an evaluation of actual tool performance, in terms of parameters previously determined with the load cell at the selected standard conditions of calibration, proved satisfactory. Throughout these tests, 8¾-in. standard tricone, hard rock toothed roller bits and carbide-insert roller bits were used. Rotary speeds were 50 and 100 rpm; static weight on bit was applied up to 40,000 Ib, and percussion frequencies up to 1,020 blows per minute were available. During this investigation it was found that toothed bits on which the teeth had developed flat ends about 3/16 in. wide did not change appreciably for the duration of a test. Hence, all toothed bits used in this study were in this condition. Conventional reference curves obtained in these tests show that increasing weight on hit by 2:1 yielded an increased penetration rate of approximately 2.7:1, while an increase in rotary speed of 2:1 netted an increased penetration rate of roughly 1.7:l. Results are thus of the same order as those reported for hard rock drilling by other investigators." CALIBRATION Under the selected standard test conditions previously described, with the lifting table hydraulically supported, and the anvil interposed between hammer and load cell, the hammers were dropped from known heights. Thus, with the kinetic energy of the hammer known, the corresponding maximum impact force shown by the cell was determined. (It may be of passing interest to note here that special drop tests with the hammers showed that no appreciable reduction in impact force resulted from introduction of the anvil or hit sub.) From these calibrations, it was possible to determine the theoretical kinetic energy available in the hammer from the maximum impact force shown by the load cell while operat-

By F. C. Kelley, L. L. Wyman

In order to clarify and amplify the existing data concerning the action of the cementing material in cemented tungsten carbide alloys, the authors have initiated this investigation of the entire range of cobalt-tungsten carbide alloys. Inasmuch as the ultimate objective is relative to what actually goes on during the sintering of cemented tungsten carbide materials, this work was necessarily restricted to heat treatments similar to those used in actual production of these materials. In the course of numerous experiments, the authors have noted several conditions that indicated that there was a solubility to be considered. Among these factors are the following: 1. Many of the alloys showed a much larger amount of binding constituent to be present than could possibly be accounted for by the cobalt content. 2. In many areas, grains of the carbide constituent are much larger than the particles of carbide originally added. In addition, these grains are of very regular contour. 2a. In samples of cemented tungsten carbide which had been fused in the atomic hydrogen torch in the presence of excess binder constituent, immense grains are formed, and their shapes are very regular. This is also true when the cemented tungsten carbide of 13 per cent. Co content is fused alone in the atomic hydrogen torch. Contrary to general expectation, chemical analysis of this material, after fusion in the atomic hydrogen torch, checks the analysis of unfused material. 3. In making the cemented tungsten carbide materials by the process of exerting the pressure at the time of heating a certain portion of the ' contents squeezed out of the mold. Chemical analysis has shown that this material contains approximately 12 to 20 per cent. of tungsten. The microstructure shows a cored dendritic structure interlaced with eutectic network, and some graphite, as shown in Fig. 1. 4. Thermal analysis of these materials has consistently indicated an arrest point close to 1350" C.

Jan 1, 1931

H. M. HOWE, Bedford Hills, N. Y.-We may clear the matter very easily, at least to a very great extent, if we look at these islands of ferrite that occur in steel castings as simply corresponding to the ferrite ghosts in steel forgings, representing the differentiation that takes place in the solidification off the molten mass. In that solidification you have dendritic crystals forming and in between those dendrites you have con-

Jan 12, 1919

By Fordyce Coburn

RICHARD ore mine of the Colorado Fuel & Iron Corp. is an underground magnetite operation located in northern New Jersey approximately four miles northeast of the town of Dover, and 40 miles west of New York City. The mine is situated on the southeastern flank of one of the many gneissic ridges having a northeast-southwest trend

Jan 11, 1953

By Carl A. Zapffe, George A. Moore

IN a previous publication from this laboratory1 the conclusion was drawn that the embrittling effect of occluded hydrogen on iron and steel must result from the precipitation of the gas within small openings through the crystal structure. A review of the literature then published indicated the real existence of crystal sub- structures of the mosaic type and gave presumptive evidence that the "rift openings" associated with hydrogen occlusion are the same as the "disjunctions" of the mosaic theory. Inasmuch as no clear conception of the actual nature of the crystal fragments and openings inherent in these theories has been established, it was considered desirable to obtain direct micrographic evidence of their true configuration. In this direction the standard methods of metallographic attack have proved useless. Recourse was had, therefore, to the direct examination of the surfaces upon which failure by cleavage had resulted from the presence of hydrogen. It was expected that such a surface, un- affected by chemical attack and undistorted by polishing, would reveal the fine openings penetrated by the gas and thus indicate the real nature of the substructures. MATERIALS STUDIED In commercial steels, defects caused by hydrogen take various external forms ac- cording to such factors as structure and purity, and to the extent to which hydrogen either occludes or produces chemical changes. The present work relates only to the well-known transcrystalline hydrogen embrittlement-"pickling brittleness"-in which elemental hydrogen occluded within the grain develops cleavage characteristics. For example, hydrogen embrittlement resulting from hydrogen reaction products is excluded from detailed study. It was also desirable, as far as possible, to have the study uncomplicated by other elements which themselves cause brittleness. Three types of iron were used. These included ingot iron, decarburized free- machining steel, and a specially prepared, aluminum-killed, electrolytic iron. This , choice allowed a comprehensive selection of unavoidable minor impurities and inclusions, which could subsequently be shown to have no specific effects on the structures within the grains. Carbon, and any other impurities free to react with hydrogen, were first removed by a preliminary annealing treatment in hydrogen. Subsequent treatment in vacuo extracted much of this hydrogen and its gaseous reaction products. The resultant ductile iron was then embrittled either by a second anneal in hydrogen, followed by rapid cooling, or by cathodic electrolysis. Group I: Prepared from Armco Ingot Iron As shown in Table I, the principal impurity in this iron was oxygen, which survived the purifying treatment to a large extent. Two series were prepared. The first (Nos. SIO-24) was purified only one day in hydrogen and dehydrogenized one day in nitrogen. Containing both hydrogen and its

Jan 1, 1943

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By D. C. Buffum, L. D. Jaffee

QUANTITATIVE measurements of the temper brittleness of steel are made by comparing the difference between embrittled and unembrittled specimens in the temperature of transition from ductile to brittle fracture. Since hardness affects the transition temperature, a study of the combined effects of hardness and temper brittleness appeared desirable. In this investigation a commercial SAE 3140 steel, which has been reported on previously in temper brittleness studies,* was used. Blanks from this steel were austenitized for 1 hr at 900°C and water quenched. The blanks were then divided into six groups and further heat treated as follows: Group 1—tempered at 675°C for 4 hr and water quenched; Groups 2, 3, 4, and 5—tempered at 675", 650°, 625', and 600 °C respectively for 1 hr and water quenched; and Group 6—tempered at 500°C for y2 hr and water quenched. Each of these groups was divided into two parts; one part was tested without further heat treatment, and the other was embrittled for 48 hr at 500°C and water quenched. Tempering treatments between 500" and 600°C were avoided because of the rapid embrittlement occurring in that range for this steel. The heat-treated blanks were machined into standard V-notched Charpy bars. Each group was tested over a range of temperatures on a 217 ft-lb Charpy machine. The energies necessary to fracture the bars and the percentage fibrous fracture of each bar were recorded. The transition temperatures were obtained from a plot of the percentage fibrous fracture as a function of testing temperature. They were taken as the lowest point on these curves at which the fracture was 100 pct fibrous. The transition temperatures for both embrittled and unembrittled specimens are presented in Fig. 1 as function of the hardness. It will be noticed in this figure that the point for the unembrittled condition at 21 Rockwell C is out of line. These specimens were tempered for 4 hr at 675 °C and this point indicated that under isothermal conditions at this temperature, as is well known, embrittlement may develop fast enough to more than offset the effects of softening. From this data, it was concluded that the difference between transition temperatures for the embrittled and unembrittled conditions at any given hardness, within the range of Rockwell C 24 % to 32lh, is constant. It is also concluded that, within the hardness range studied, the transition temperatures for embrittled and unembrittled specimens rise in a parallel fashion with an increase in hardness. The authors wish to acknowledge the assistance of Frank Carr in this work.

Jan 1, 1952

By Vinícius Cunha de Souza

Dispositivos atuatores com componentes de ligas de NiTi podem ter seu desempenho modificado quando submetidos a distintas taxas de aquecimento e/ou resfriamento resulte numa transformação de fase. Por outro lado, por norma, as temperaturas de transformação de fase (início, pico e fim) devem ser estabelecidas a partir de taxas fixas de 10ºC/min (tanto no aquecimento como no resfriamento) através da técnica de Calorimetria Diferencial de Varredura (DSC), sem levar em conta a dinâmica do material durante a transformação em aplicações reais. O presente trabalho procura observar a transformação de fase do material avaliando a capacidade de resposta do mesmo, quando submetido a ciclos em um DSC sob diversas taxas de resfriamento e aquecimento, entre 1 e 10ºC/min em uma liga de NiTi rica em Ti, com formação de fase R durante o resfriamento e/ou aquecimento. Os resultados de DSC foram submetidos a um tratamento de dados com o intuito de melhor determinar as temperaturas de transformação de fase associadas as frações transformadas. Pode-se verificar que valores de taxas de resfriamento e de aquecimento superiores a 7°C/min permitem que ocorra uma tendência para um incremento do intervalo entre as temperaturas de início e fim das transformações direta e reversa.

Aug 16, 2017

By Kristian Drivenes, Steinar L. Ellefmo, Kurt Aasly, Ben Snook, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

"Since Ellefmo et al. (2014) published resource estimates of undiscovered seafloor massive sulfides (SMS) on the Arctic Mid-Ocean Ridge (AMOR), there has been an increased focus on establishing new knowledge about exploitation technologies for such deposits. This also includes understanding the process mineralogical properties of typical SMS deposits.The part of the AMOR that lies between Jan Mayen and the Svalbard Islands and is located within Norwegian jurisdiction and, as such, investigating the potential for mineral production from hydrothermal vent fields has been seen as strategic. The AMOR has been explored for active hydrothermal vent fields since early 2000s (Pedersen et al., 2010b). One of the active vent fields discovered, Loki´s Castle, is located in the northern part of Mohn´s Ridge. This vent field was first described by Pedersen et al., (2010a) and consists of two mounds, each approximately 100-150 m diameter and 20-30 meters high, hosting several active chimneys, up to 11 m high.Loki´s Castle has been selected as a case site in order to study the properties of typical SMS occurrences with respect to possible future deep-sea mining activities. As part of the MarMine cruise in 2016, the Loki Castle was visited and sampled for e.g. mineral characterization and mineral processing analyses. In total, more than 500 kg rock samples were collected using ROVs, and intended for further research (Ludvigsen et al., 2016). In addition to sampling mineralized rock fragments, survey data like bathymetry, magnetics and Underwater Hyperspectral Imaging (UHI) was collected using Automated Underwater Vehicle (AUV)."

Jan 1, 2017

Determine the site specific flow behavior of leachants and groundwater during development, production, and restoration phases of an in situ leaching operation. Approach A computer program has been developed which simulates the hydrologic activity associated with in situ mining. Various user options enable modeling of many of the site specific geologic conditions and well field specifications that affect the hydrology of solution mining. How It Works In situ hydrology is modeled, using a closed-form solution to the three-dimensional, partial differential equation that describes changes in hydraulic head as a result of pumping from leachant Injection and recovery wells. Model capabilities include arbitrary well patterns and pumping schedules, partially penetrating well screens, directionally anisotropic permeability and natural groundwater flow, in either

Jan 1, 1981

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

NTRODUCTION Surface subsidence monitoring is the most effective means for investigating the nature of, and developing the techniques for pre¬dicting the surface movement and deformation process. However, because of imperfection in survey equipment and field practices, the surface movement data collected from field survey are not error-free. Also due to lack of proper numerical techniques for computing surface deformation from the measured surface move¬ment data, a relatively large portion of the subsidence data col¬lected could not provide information other than surface movement. In a paper by Luo and Peng (1992), the sources and magnitude of errors in the measured surface movements using an electronic total station in subsidence survey are discussed. If the errors in the measured surface movement components are left untreated before calculation for deformation indices (i.e., slope, strain and curva¬ture), the errors will be carried over to the deformation indices and enlarged if improper numerical procedures are used in the calcu¬lation. It should be noticed that in protecting structures affected by ground subsidence, accurate surface deformation indices are much more important than surface movement. In order to improve the accuracy of the collected surface movement data and the calcu¬lated deformation indices, a number of numerical procedures are also proposed in the same paper. The proposed techniques include: a data smoothing technique for data pre-processing; and a number of numerical methods and/or procedures for calculating surface deformation indices from the measured surface movement data. DATA SMOOTHING Because of various factors, the measured surface movement data always contain errors, small or large. In order to better utilize the collected data, a data smoothing method is proposed to correct the errors in the measured movement data. The method uses the same concept as the influence function method (e.g., Knothe, 1957) on which many existing subsidence prediction methods are based. The data smoothing method makes necessary corrections on the measured movement for the point of interest according to not only the measured movement at this point but also those at the surrounding points. The contribution of a surrounding point in making the correction for the point of interest is inversely propor¬tional, in exponential form, to the distance between them. The new magnitude of a movement component at the point of interest (Zi*) is calculated by

Jan 1, 1992

By H. M. Day

THE constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were con-firmed and supplemented through X-ray analyses by Preston and Stenbeck.3 According to Murphy, at 276° C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower tempera-tures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region.

Jan 1, 1938

By R. J. Keene

The South Works high-tonnage billet caster was started in late March 1971, with the first heat being successfully cast to completion. Currently, over 31,500 tons per month are being produced. U. S. Steel designed and built this caster with the objective of producing quality-steel billets for critical bar, rod, and wire applications. The essential design parameters were based on studies conducted on the Research Laboratory's pilot caster, also located at South works. 1,2,3)* The caster is a four-strand, straight-mold machine that produces 7.5-inch- square billets at rates exceeding 300 tons per hour. An in-line-reduction mill reduces each strand to either 6-inch-, 5-inch-, or 4-inch-square billets.

Jan 1, 1972

By A R. Cruden, M S. Egglseder

The formation of banded iron formation (BIF)-hosted high-grade iron ore deposits in the Hamersley Province, Australia has been debated for decades. Although a structural control on their formation is widely accepted, only the roles of large-scale structures (ie faults and folds) formed by brittle and ductile deformation have been considered to date. However, the deformation of multilayered sequences in the Hamersley Province (ie the Mount Bruce Supergroup), with their contrasting rheological behaviours, creates challenges for understanding the complex structural framework at regional to deposit scales, including the significance for mineralisation and orebody location.Our approach to understanding these complex relationships is based on an established principle of structural geology, which is to extrapolate microscale structures to deposit-scale structures and vice versa, supported by state-of-the-art 3D modelling techniques. Complexly deformed hand samples associated with the Mount Tom Price iron ore deposit (Hamersley Province, operated by Rio Tinto Ltd) have been analysed and visualised with 3D explicit (Move™, Midland Valley Ltd) and implicit modelling software packages (Leapfrog™, AranzGeo Ltd) and supported by microstructural investigations (optical and X-ray microscopy) and fieldwork.Our study shows that the deformation of BIFs in the central Hamersley Province is controlled by microscale chemical processes (ie dissolution precipitation creep) due to rheological differences between iron oxide and chert layers, contrasting fluid flow properties and layer thickness variations. These processes account for the removal of vast amounts of silica, its transportation by diffusion in the presence of a fluid and reprecipitation at low-pressure sites. Consequently, this structural framework was used by different upgrading fluids to form iron orebodies.CITATION:Egglseder, M S and Cruden, A R, 2015. Evolution of a structural framework for high-grade iron ore deposits, in Proceedings Iron Ore 2015, pp 255–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By William Greenawalt

The Greenawalt electrolytic copper extraction process is applicable to suitable oxide ores, sulfide ores and concentrates, and low-grade matte. The process is self-sustaining in acid on sulfide ores or concentrates, on mixed ores, on high-grade oxidized ores; and on low-grade oxidized ores the amount of acid to be purchased or manufactured is greatly reduced. The ferric iron is under easy control, and copper may be effectively deposited from solutions of any acid or iron content likely to be used in copper leaching. From 60 to 75 per cent. of the copper may be removed from the solution in passing through the electrolytic department, before returning the solution to the ore. The amount of copper requiring chemical precipitation, from the waste and foul solutions, is only about 5.0 per cent, of the total copper produced, and this 5.0 per cent. is converted into the electrolytic metal in the regular operation of the process. The entire process can be made practically automatic, and can be carried out mechanically. There is no uncertain departure of any kind in the application of the process; no unusual or unproved apparatus is used. EVER since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydro-electric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods.

Jan 1, 1924