Search Documents

By P. Payson

EMBRITTLEMENT of hard-tempered martensite (500°F embrittlement) appears to be coincident with the beginning of the third stage of tempering. During the first stage, primary martensite of steels containing over 0.25 pct C decomposes to a mixture of c carbide and martensite of appreciably constant carbon content close to 0.25 pct.' During the third stage of tempering, cementite forms. In steels with

Jan 1, 1955

Jan 1, 1969

By D. E. Mikkola, G. E. Poquette

X-ray diffraction was used to study the growth of antiphase domains in quenched (or "disordered&apos;? Cu3Au annealed in the range 300" to 385°C. Measurements of the long-range order parameter indicate that a high degree of order is established rapidly at these annealing temperatures. Average domain sizes obtained by Fourier analysis of the superlattice peak profiles show that antiphase domain growth is analogous to classical metallurgical grain growth (i.e.,fol-lows a D2 US kt relation). The activation energy for the growth process, 44 kcal per mole, indicates diffusion control. The anisotropy in the observed effective domain sizes from seven different superlattice peaks can be best accounted for by a configuration involving antiphase domain boundaries on {100 } and (111 ) planes, where the (100) boundary is the low-energy type, {lOO} Type I. The disappearance of the (111) antiphase domain boundary during domain growth is dif-fusion-controlled with an activation energy of 48.5 kcal per mole. On the other hand, the behavior of the parameter representing the amount of (100) Type I boundary indicates that there may be a conversion of the higher-energy boundary types to (100) Type I boundary during the growth process. THE order-disorder transformation in the alloy Cu3Au has been the subject of numerous experimental investigations over the past 40 years, most of which have involved measurements of convenient physical properties such as resistivity and hardness as a function of heat treatment. The interpretation of these data is difficult because measurements of this type have the disadvantage that they yield total changes resulting from several different atomic processes which may be occurring simultaneously. The present study was undertaken to establish by means of X-ray diffraction the kinetic behavior of one of these atomic processes, namely antiphase domain growth. In the completely ordered state Cu3Au has an L12 structure which can be described as an fcc type arrangement of atoms in which the gold atoms occupy the corner sites and copper atoms the face-centered sites. Three other equivalent unit cells can be formed by allowing two gold atoms to occupy opposite face-centered sites and copper atoms to occupy the remaining corner and face-centered sites. These four different unit cells are crystallographically related by a shift of 1/2<110>. Quenching from above the critical temperature (392°C) to room temperature retains the "disordered" structure-a "random" arrangement of copper and gold atoms having the fcc structure. Annealing the disordered alloy below the critical temperature causes ordering to occur through the nucleation and growth of ordered regions at different points throughout the crystal. These small ordered regions, each based on one of the four types of unit cell, grow by consuming the disordered material until they impinge to form a domain structure in which the domains are antiphase by a shift of 4(110). The boundaries between domains are called antiphase domain boundaries (APDB) and they have been found to lie primarily on &apos; {100} planes in highly ordered Cu3Au. Two types of APDB can occur on ( 100) planes. An example of an (001)1/2[110] shear type APDB is shown in Fig. I. Because of the layer of copper atoms separating the domains in this case, there are no near-neighbor violations across the boundary and it has a low surface ener This type of APDB will be referred to as {lOO} Type I. Fig. 2 shows an (001): [011] climb type APDB, (100) Type 11. This type of APDB can be described as resulting from removal of a (200) plane followed by a shift of 1/2<110> to bring the separated regions together. Near-neighbor violations across (100) Type I1 APDB make it a high-energy boundary. There are numerous other possible APDB configurations; however, it is only worth noting that shear type APDB can be produced on the (111) plane by motion of a normal fcc dislocation with Burgers vector 1/2<110> through the ordered structure. A (111); [110] shear type APDB is shown in Fig. 3. Again, because of the near-neighbor violations this type of APDB has a higher energy than the (100) Type I APDB.

Jan 1, 1970

By Rubén Alvarado

The markets and environmental protection rules are more and more exacting, both of which have determined that copper smelters should look for technological development and global management to ensure their viability and competitivity in the short and long term. The main facilities of the present and future Smelting-Converting Process at Codelco&apos;s Caletones Smelter, is based on Teniente Converter reactors with a high operational availability that have reached concentrate processing capacities near 2,000 tpd. These reactors are in operation in most of the smelters in Chile as well as in Zambia, Peru, Mexico and, in ?the near future, in Thailand. Since 1993, the Smelting-Converting process of the Caletones Smelter of Codelco-Chile has been based on one Reverberatory furnace, two Teniente Converters and four Peirce-Smith Converters. These facilities, together with the operation of two Fluidized Bed Dryers, three Slag Cleaning Furnaces, and two Oxygen Plants have allowed the smelter to reach concentrate smelting capacities and copper productions of 1,215 kt/year and 360 kt/year, respectively. This transitional operating scheme, combining together traditional and advanced technological equipment, needs further modernization to successfully face the modern world challenges, especially with relation to the environmental commitment, production costs and wide satisfaction of customers. For this reason, for the period 1997-2000, a Modernization Plan has been worked out. This plan considers an increase of the present throughput, which will permit a significant increase in productivity, as well as finding a definitive solution for meeting the environmental regulations. Among these projects, we can point out the definitive shut down of the Reverberatory Furnace, which is a contaminating piece of equipment of low energetic efficiency. Additionally, it considers the installation of two new Slag Cleaning Furnaces, one additional Oxygen Plant, and the incorporation of two new Sulphuric Acid Plants with a production capacity of 4,500 T/D, that will recover over 92% of the sulphur content, of process off-gases.

Jan 1, 1998

By W. L. Oliveira, J. R. Sobrinho, V. M. Hamza, S. M. Eston

The Ipueira III chrome mine is located in the northeastern part of the state of Bahia, Brazil. Extraction is actually at depths less than 300 m, but below level 200 serious environmental problems have been encountered with respect to control of air quality, toxic gas, dust and thermal comfort. At the request of the mining company the University of São Paulo started a research program to investigate the origin and occurrence of the critical problems and to propose solutions. A ventilation survey was carried out first which revealed the existence of several air leakages and short circuits that contributed to substantial reductions in the air supply to some of the main producing levels. Computer simulation of the ventilation network showed that extending the intake air shaft to deeper levels was the most convenient and economic solution to improve the air quality. The ventilation survey was followed by a mapping of the toxic gas emissions and thermal comfort levels in several parts of the mine. The air quality conditions were evaluated as a function of gas emission and heat generation associated with production and development activities. The results show that environmental conditions are already critical in most of the working levels and neither an increase in production nor deepening of the mine can be taken up without substantial changes in the ventilation system. INTRODUCTION Environmental concern is growing in Brazil and several underground mines are starting environmental engineering programs. The LACASEMIN - Laboratory of Environmental Control and Mine Safety of the Mining Engineering Department of the University of São Paulo - was contacted by Mineração Vale do Jacurici to start a research program for investigating the origin and occurrence of environmental problems that existed in the Ipueira III chrome mine. This research program involved field measurements of air quantities with gas levels monitoring, evaluation of heat stress parameters, determination of adequate flow patterns through computer simulations and training of mine technical staff. This paper presents the results of the first 4 months of this research program. The Ipueira III mine is located in the northeastern part of the state of Bahia, near the city of Senhor do Bonfim at about 400 km inland from the state capital city of Salvador. Chromite mineralization is quite widespread in this area and often associated with mafic and ultramafic rocks which cut across regional gneisses and migmatites. ROM production in 1992 varied between 25,000 to 40,000 tons per month, 25% being of lump type (38% of Cr2O3) and 75% being of fines. Lump is manually separated and fines are concentrated in a nearby plant. All the production goes directly to the group processing steel plants near Salvador. The Ipueira III mine is currently under some adverse economic situation because of imports from South Africa and Russia, which have better grades and sometimes a lower content of phosphorous. Consequently there has been little progress in the development of new mines and even in those currently under operation the extraction is becoming more difficult due to the lack of investment in improving mining methods and ventilation systems. In spite of such difficulties the company has backed up studies for initiating an environmental engineering investigation of the Ipueira III mine. MINING METHODS AND VENTILATION SCHEMES The mining methods adopted have changed as a function of extraction depth, rock mass strength and ore body geometry. Initially the orebody was found to be fairly continuous and dipping at about 55 degrees from surface

Jan 1, 1993

By S. N. Singh, M. C. Flemings

Results are presented of a study on the combined influences of ingot dendrite am spacing and thermo-mechanical treatments on the fracture behavior and mechanical properties of high purity 7075 aluminum alloy. The most important single variable influencing mechanical properties was found to be undissolved alloy second Phase (microsegregation inherited from the original ingot). Ultimate and yield strengths were found to increase linearly with decreasing amount of alloy second phase while ductility increased markedly. At low amounts of second phase, transverse properties were approximately equal to longitudinal properties. In tensile testing, microcracks and holes were invariably found to originate in or around second phase particles. Fracture occurred both by propagation of cracks and coalescence of holes, depending on the distribution and amount of second phase. IN most commercial wrought alloys, second phase particles are present that are inherited from the original cast ingot. These include, for example, non-equilibrium alloy second phases such as CuAl2 and impurity second phases such as FeA13 and Cr2A1, in aluminum alloys. A previous paper1 has dealt with the morphology of these second phases in cast and wrought aluminum 7075 alloy, and with their behavior during various thermomechanical treatments. In this paper we discuss the influence of the particles on mechanical properties and fracture behavior of the alloy. Previous experimental work indicating a direct and major effect of second phase particles on mechanical properties (especially on ductility) includes the work of Edelson and Baldwin on pure copper.&apos; Also relevant are the many studies demonstrating the important effect of nonmetallic inclusions on the fracture of. steel.3&apos;4 Work on aluminum includes that of Antes, Lipson, and Rosenthal5 who showed that a dramatic improvement in ductility of wrought aluminum alloys of the 7000 series is achieved by eliminating second phases. It now seems well established that included second phases play a dominant role in controlling ductility (as measured, for example, by reduction in area in a tensile test) of a variety of materials. There is, therefore, considerable current interest in the mechanisms by which second phase particles affect ductile fracture. Experiments done by various workers have shown that second phase particles or discontinuities in the microstructure are potential sites for nuclea-tion of microcracks and of holes,6-l3 which then grow and cause premature fracture and the loss of ductility. Theoretical attempts have been made to explain the observed phenomena; most are able to explain observations qualitatively, but lack quantitative agreement. Much experimental work needs to be done to aid extension of theoretical models. A recent review article by Rosenfield summarizes work in this general area.14 PROCEDURE Material used in the previously described study on solution kinetics of cast and wrought 7075 alloy1 was also used in this study. Procedures for ingot casting, solution treating, and working were described in detail in that paper. Test bars were obtained for material of 76 initial dendrite arm spacing (11/2 in. from the ingot base) and 95 µ initial dendrite arm spacing (51/2 in. from the ingot base) for the following thermomechanical treatments (solution temperature 860°F; reduction by cold rolling). a) Solution treated 12 hr, reduced 2/1, 4/1, and 16/1. b) Solution treated 12 hr, reduced 16/1, solution treated approximately 5 hr after reduction. c) Same as a) except solution treated 24 hr prior to reduction. d) Same as b) except solution treated 24 hr prior to reduction. e) Same as d) except solution treated 20 hr after reduction. Test bars were taken both longitudinally and transverse to the rolling direction. Transverse properties are in the long transverse direction; since the final product was sheet (0.030 in. thick), properties in the short transverse direction could not be obtained. Test bars were flat specimens, of gage cross section1/-| in. by 0.030 in. and 1/2 in. gage length. After machining the test bars, they were given an additional 1/2 hr solution treatment of 860°F and aged 24 hr at 250°F. Three bars were tested for each location and thermomechanical treatment, after rejection of mechanically flawed bars. The average results of these three bars are reported. Elongation was measured using a $ in. extensometer and reduction in area was determined using a profilometer to measure the area after fracture. INFLUENCE OF THERMOMECHANICAL TREATMENTS AND SECOND PHASE ON MECHANICAL PROPERTIES Results of mechanical testing are presented in Figs. 1 to 4 and in tabular form in the Appendix. A general conclusion from results obtained is that details of the thermomechanical treatments studied were important only insofar as they influenced the amount of residual second phase. Figs. 1 and 4 show the longitudinal properties obtained (regardless of thermomechanical

Jan 1, 1970

By McClelland. John J.

This Bureau of Mines report discusses recent applications of water in-fusion technology to control dust in U.S coal mines and presents recommended guidelines for determining coal seam infusibility. The techniques required to use water infusion are presented in detail. A Bureau case study indicated that water infusion reduced dust levels by 68 pct along a longwall plow face, bringing this section into compliance with the Z.0-mg/m3 Federal dust standard. Similar studies conducted by Occidental Research Corp. under a Bureau contract show water infusion at two longwall double-drum shearer operations produced dust reductions ranging from 38 to 50 pct. Water infusion was found to be cost effective, aver-aging 5 cents per ton.

Jan 1, 1987

By V. T. Vacariu, P. D. Georgescu, N. Tomus

To assess the potential for radioactive pollution unique to the environmental conditions of the Bacau phosphogypsum waste dump, surface samples were taken, drillings were performed on the entire waste dump&apos;s height, and the Ra226 distribution on the height and surface considered to contain a medium content of the radium of 0.57 Bq/gr was studied. Thus, the waste dump&apos;s radioactive potential was estimated at 30-40 Ci in equivalent Ra226. Also analyzed was the granulometric composition of the phosphogypsum and the distribution of Ra226 on granulometric orders, which indicated that the radium was concentrated in the very fine fractions. Parameters were set up for the classification by hydrocycloning to obtain a fine class (less than 41 microns) having a radium content of more than 0.9 Bq/gr and a coarse class having less than 0.37 Bq/gr. A chemical process was devised for removal of the radium from the phosphogypsum with the possibility for recovering the contained sulfur.

Jan 1, 1999

By Lyle L. Marsh, David L. Douglas

CORRELATION was made between the heat treatment and hardness of three U-Ti alloys ranging in composition from 8.5 to 50 atomic pct Ti. The following important observations were made: 1) A direct quench of y U-Ti solid solution resulted in the formation of a hard martensitic phase in low-titanium alloys. 2) Subsequent tempering initially increased the hardness by the precipitation of a fine dispersion of U2Ti; further precipitation of U2Ti with tempering time eventually resulted in softening. 3) High-hardness levels were obtained also by isothermal transformation of an 8.5 atomic pct Ti alloy at 400º and 500°C. 4) The crystal structure of the phases present at the solution-treating temperature (one region in the phase diagram excepted) and the temperature within a given phase region affected the hardness of both quenched and isothermally transformed alloys. Introduction It has been known since 1887 that the mechanical properties of metals were dependent upon their microstructure. Sorby pointed out in that year that annealed gray iron castings were softer than chilled iron castings by virtue of the graphite which had replaced hard cementite in the microstructure. Over the years, interest has increased in the effect of microstructure on the mechanical properties of metals, and now high-strength levels may be achieved by bringing about the dispersion of a second phase or by other microstructural adjustments. The nature of a second phase in an alloy strongly influences the properties. For example, the size, shape, amount, and distribution of a second phase plays a very important role in the ultimate properties of an alloy. Microstructural control is achieved by heat treatments. Hence, any alloy system of potential use should be understood in terms of its response to heat treatment and the resultant effects upon the properties.

Jan 1, 1958

By A. W. Hudson, G. D. Van Ardsdale

Heap leaching, as practiced at Rio Tinto, Spain, while one of the oldest, and probably one of the cheapest, methods of extracting copper from its ores, has not had, until recently, other than experimental application in this country. This has been due partly to a mistaken idea that the Rio Tinto ores possess some obscure and mysterious quality that renders them alone suitable to the process, partly to the fact that tests properly made meant the expenditure of large sums of money and several years time, and partly to the fact that favorable commercial and other conditions are not often found. This paper gives some views on the chemistry and mechanism of the method, an account of the preliminary experiments, and the final plans adopted for a large-scale installation of the method by the Phelps Dodge Corpn. for treating low-grade ore from Sacramento Hill, Bisbee. If results comparable with those obtained from the test heap are to be had from the large plant, this plant will operate on the lowest-grade sulfide ore now being treated commercially in the country. The method has several advantages: The installation cost is low. Interest charges must, of course, be made both on the cost of the ore delivered to the plant and for the plant itself, but as these are low, there is considerable advantage in the ability to regulate output by more or less complete shutdowns in accordance with market and other conditions. The amount of labor needed is small, and the cement copper produced may be considered nearer a finished product than the sulfide concentrates from a mill, and certainly means less installation cost per ton to put into final form by present methods. At Bisbee, conditions were favorable for a trial of the method for, in the preparation of the Sacramento Hill orebody for steam shoveling,&apos; a large amount of material below concentrating grade had to be moved to

Jan 1, 1923

By Paul W. Cleary

Keywords: Reactive pellets, CFD, Lagrangian SPH, Pyrometallurgy In several pyrometallurgical processes, reactive pellets are added to a melt. Heat is transferred to the pellets and reaction products such as gases, metal and slag are formed. For many pyrometallurgical processes traditional grid based CFD methods, such as using the Finite Element Method (FEM) and Finite Volume (or Control Volume methods), produce suitable predictions. However, the inclusion of solids in the bath represents significant challenges for these methods. Smoothed Particle Hydrodynamics (SPH), a Lagrangian simulation method, is able to simulate both the fluid component of the bath and any immersed solid materials, tracking the motion of these solids, and their interaction with the fluid, including gas generation. In this paper, we will summarize the key aspects of the SPH method and will show a series of structured examples illustrating the behavior of the different physics sub-systems that are used in the model of the overall system.

Jan 1, 2005

[In selecting deposits for exploration projects, tabular deposits or large mineralized masses are favored because they may be explored systematically and because they afford the best opportunity for blocking out reserves in advance of mining whereas irregular, small pipes and scattered]

Jan 1, 1941

By Alfred Boyles

THE experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of funda-mental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic and in others i produced al marked changes in the size of the graphite flakes. These effects seemed to be III sulphur and manganese present in the material studied. Iron-carbon- respond silicon alloys did same manner as mg cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of FIG. 1.-APPARATUS FOR MELTING UNDER PRESSURE. silicon. The present paper is con- A, inlet for gas. cerned with alloys of lower silicon B, outlet for evacuation. content and describes the structural C, power lead. D thermocouple changes produced by melting in E, plug for access to furnace. various atmospheres at pressures F, crucible. ranging from a partial vacuum up to 300 lb. per sq. inch.

Jan 1, 1939

By B Whiteley, B Gee

The Northside Storage Tunnel is a TBM driven rock tunnel system designed to collect and store sewage from four major storm overflow points along the existing Northern Suburbs Ocean Outfall Sewer. At present, sewage overflows during wet weather are the main source of pollution for Sydney Harbour. The tunnel system comprises a 16 km long by 3.8 m to 6.5 m diameter tunnel from Lane Cove to the North Head Sewage Treatment Plant and a 4 km long by 6.3 m diameter branch tunnel from West Chatswood. The tunnel will have a typical rock cover of about 50 m to 150 m. Most of the tunnel alignment is contained within the Hawkesbury Sandstone Formation which is generally an excellent tunnelling stratum, and offers few geotechnical constraints. However, the tunnel is required to pass beneath incised palaeochannels at Middle Harbour and Manly with each palaeochannel containing about 70 m of sediment.Innovative geotechnical and geophysical investigations were undertaken to examine the tunnel route and characterise the rock beneath the palaeochannels. These investigations have located zones of poor quality rock beneath one palaeochannel in particular, suggesting significant stress relief had taken place in the rock at times of lower sealevel producing structural features indicative of valley bulging. This paper presents the geotechnical model developed for the tunnel, and the models and constraints for tunnelling beneath the palaeochannels.

Jan 1, 1999

By Euzebio De Oliveira

ONE of a recent batch of samples from the Serra da Baliza, in the state of Parana, Brazil, contained asphalt and a dark heavy oil; and workmen on the railway from Porto União to Uruguay discovered asphalt, coming from eruptives that outcrop along the Rio de Peixe. The occurrence f asphalt in the triassic eruptives of southern Brazil, however, has been known a long time, according to Dr. Gonzaga de Campos. It is generally believed that the Botacatú sandstone is always a hard vitrified rock, from the metamorphic action f. the overflowing eruptive contacts. In this region, however, the contact metamorphism is almost nil; the sandstone is slightly hardened in a narrow zone about 20 to 30 cm. wide. In many places, the sandstone is so friable as to be easily reduced to sand, which is used-.in, mortar for building in Guara-puava and Palmas. South and west from Porto União,. this bench of sandstone is about. 50 m. thick, and is capped by a heavy bed. f basic eruptives, many of which are amygdaloids. Dr. Geo: P. Merrill, after studying the triassic eruptives collected by the Coal Commission, reached the conclusion that. "All these rocks are of typical basalt-diabases, not in any essential different other than in structure. An interesting mineralogical phase is its paucity in olivine, which in many cases is completely lacking. Professor Hussak, who carefully studied these rocks and their accessory minerals, decided that in the dikes they are granular (diabase) and, that in the lava sheets, porphyritic (augite-porphyrite or melaphyre), and that the latter pass evidently to normal diabases and are always typical of effusive rocks. The examination f many slides from dikes and sheets leads us to adopt the opinion of Professor Hussak; the rocks of the dikes are of ophitic structure, while that of the sheets show a great variety f structure and may vary from almost granular to basaltic. The great paucity in olivine had been noted by Hussak, who classes as melaphyres, the porphyritic triassic rocks in Brazil which contain olivine.

Jan 4, 1921

The Diamond mechanical soot blower system, manufactured by the Power Specialty Co., Detroit, Mich., consists of a permanent installation of units arranged in groups to fit the design of the various boilers to which they are attached. The units are so arranged as to effect the cleaning of the fire surfaces of the boiler, particularly the tubes, by means of steam jets. When this steam is released among the tubes at a velocity of approximately 2700 ft. per sec. (assuming a pressure of 150 lb.), a perfect whirlwind of currents is created, reaching all the nooks and crannies of the boiler, and thoroughly removing the particles of soot and fine-ash accumulation. This operation requires but a moment&apos;s time-from 20 to 50 sec. per unit¬and is performed from two to four times a day, while the boiler is under full load, using a greatly decreased amount of steam and labor as compared with the hand hose or any other system of blowing. Moreover, this cleaning is effected without admitting air, with its cooling effects, to the boiler setting. The Diamond model "G" blower consists of five principal elements as follows: 1. A head through which the steam passes from the main supply line when the valve is opened. The head is the foundation element to which the other elements are attached. 2. A wall box which is bricked into the setting. The box supports the unit, and is so constructed that the blower can be turned freely without admitting air to the inside of the setting. 3. A blower element running cross-wise of the bank of tubes, and consisting of a small header with nozzles so placed as to discharge steam between the boiler tubes. 4. A sheave or hand wheel by means of which the blower element is rotated. 5. Bearings attached to the boiler tubes which support the blower element and permit it to revolve freely. The nozzles from which the steam issues are designed on the principle of the Venturi tube, and vary in design for different pressures. The expanding walls of the Venturi nozzle increase the velocity of the steam over 200 per cent., as compared with a nozzle having a straight orifice. Thus, the velocity of the steam issuing from a straight nozzle at 150 lb. pressure is 912 ft. per sec., whereas, at this pressure the velocity of the steam issuing from a Diamond Venturi nozzle is 2795 ft. per second.

Jan 5, 1918

By I. Gaballah

High and low grade concentrates of tantalum and niobium oxides were obtained by leaching a medium grade tin slag. Chlorination and carbochlorinalion of these concentrates were studied between 200 and 1000 "C. Chlorination or carbochlorination of the low grade concentrate led, at 1000 OC, to the extraction of about 95 % of the tantalum and niobium oxides. However, the tantalum and niobium chlorinated compounds were contaminated by iron and manganese chlorides. Complete extraction of the niobium and tantalum pentoxide was achieved during the carbochlorination of the high grade concentrate at 300 and 500 "C, respectively. While chlorination of this concentrate at 1000 "C, allowed to the volatilization of about 60 and 80 % of Ta205 and Nb205. In both cases, condensates were composed of almost pure tantalum and niobium chlorinated compounds. The results demonstrate the advantages of the lixivialion based on the "pseudo- structure" of the raw tin slag to obtain the high grade concentrate. The conclusions of this work suggest that the carbochlorination of the high grade concentrate is an efficient process for the extraction of refractory elements from tin slag.

Jan 1, 1993

By Larry A. Haas

The U.S. Bureau of Mines, in cooperation with Cleveland-Cliffs, Inc. (Hibbing, MN), investigated ways of enhancing the quality (compressive strength, after-tumble and reducibility) of domestic acid and fluxed magnetite pellets by modifying the oxygen content during the preheat and induration periods of the firing operation . Oxidation of magnetite was best accomplished when sufficient oxygen and time were available before the peak induration temperature was reached. The rate of magnetite oxidation increased directly with the gas oxygen content during the preheat period at 7000 C and above. With 30 pct ( or more) O2 and a preheat rate of 2000 C/min, most of the magnetite was oxidized during the preheat period. With laboratory tube and mini-pot furnace tests, oxygen enrichment during the preheat period improved the pellet properties more in the simulated grate-kiln tests than in the simulated straight-grate tests. The longer induration period with the grate-kiln test resulted in more sintering of the residual magnetite and its reaction with the silicon compounds. When flux was present in the pellets, calcium silicates and calcium and magnesium ferrites were formed. More calcium ferrite was formed when the magnetite was oxidized early and less iron was present in the fayalitic calcium silicate slag.

Jan 1, 1993

By Sunil S. Gandhi

"Uranium occurrences are widely distributed in tuffaceous-argillaceous beds and abundant rhyolitic volcanic rocks of the upper Aillik group, which is more than 3 km thick and over 125 km by 40 km in areal extent. They include partially developed Kitts and Michelin deposits, containing 1560 and 7366 t U respectively.Uranium occurs mainly as disseminated fine pitchblende grains in beds and lenticular stratabound zones, and rarely as coarse pitchblende aggregates and thin veinlets. The Kitts deposit and ten other occurrences are in the argillaceous-tuffaceous beds within a steeply dipping stratigraphic zone, less than 50 m thick and over 20 km long, at the base of the upper Aillik group. The occurrences hosted by the rhyolitic rocks, numbering over fifty and including the Michelin deposit, are in elongate structural-stratigraphic belts or zones, and are characterized by a pronounced enrichment of soda and depletion of potash associated with mineralization. The mineralized zones are affected to a varying degree by Hudsonian deformation, metamorphism and granitic intrusions.The uranium mineralization is interpreted as genetically related to the felsic volcanism, involving syngenetic deposition in argillaceous-tuffaceous beds and epigenetic emplacement in rhyolites. The volcanic activity occurred 1855 ± 5 Ma ago according to a preliminary U-Pb zircon date on porphyritic rhyolite. Pitchblendesfrom the Kitts and Michelin deposits and a few other occurrences in rhyolites have yielded nearly concordant dates in 1810 to 1730 Ma range. They reflect resetting of isotopic equilibrium at the time of Hudsonian deformation. Other isotopic data on pitchblendes and galena from veins and aggregates .in the south near the 'Grenville Front' indicate local redistribution of uranium and radiogenic lead at the time of Grenville Orogeny approximately 1100 Ma ago."

Jan 1, 1986

By O. D. A. Pease, C. D. Young, C. H. Strand

In an effort to employ cast steel of a stronger structure than that found in the annealed steel casting, the possibilities of heat treatment which will increase the strength without materially decreasing the ductulity may be resorted to.

Jan 1, 1915