Search Documents

By Allan J. MacRae

A copper alloy to be used for coils in cast copper cooling blocks has been identified and samples prepared for metallurgical examination and destructive testing to compare with cast cooling blocks manufactured from copper and nickel-copper alloy pipes. The copper alloy allows for the formation of a metallurgical bond between the pipe and the cast copper during the casting process, which does not normally occur with pure copper or nickel-copper alloy pipes. The alloy's coefficient of thermal expansion is also much closer to that of pure copper compared with nickel-copper alloys, so there is less strain induced at the pipe-cast copper interface due to differential thermal expansion. It is expected that this new pipe coil alloy and associated casting techniques will allow for the production of cast copper cooling blocks that have greatly enhanced service life in high heat load applications compared to existing technologies.

Jan 1, 2002

By John M. Warde, Eileen P. Burke

ORES of manganese and chrome have a high order of strategic importance, both metals are basic to the metallurgy and usefulness of steel, the fabric on which our economy rests. Looking beyond the current recession and short range picture of oversupply in these ores, this review attempts to answer the following questions regarding the longterm outlook for these key commodities: By 1970, what will be the probable demand here and abroad, what are future supply prospects, and what effect is the USSR likely to have on the world market? (See summary forecast on facing page.)

Jan 8, 1958

By Ralph B. J, Sadler W. R

Thiobacillus ferrooxidans was shown to catalyse biodegradation of chalcopyrite concentrates. The process was growth associated at normal temperatures (30°C) in dilute acid solution (pH2, H2SO4) in submerged cultures. Approximately 20% of the copper dissolved in 22 days in the presence of T ferrooxidans while less than 0.6% was released when bacteria were absent. In ore column leachates, the iron and sulphur oxidizing species T ferrooxidans, ranged from I04 to I06 cells/ml while exdusively sulphur oxidizing species ranged from I02 to 104 cells/ml. T ferrooxidans predominated below pH 3 while other sulphur oxidizing bacteria favoured higher pH. Organisms were distributed vertically in ore columns according to pH differences, resulting from gradual acid consumption by gangue, during trickle irrigation.There was a sequential development of bacteria in leachates from fresh ore irrigated with water only. High pH sulphur oxidizers were always present, low pH sulphur oxidizers appeared within a week while T ferrooxidans took 50 days to show up. Routine monitoring of bacteria in dump leachates provided a qualitative indication of events in otherwise inaccessible ore bodies.

Jan 1, 1981

By Wm. Reuben Webster

THE greatly enlarged demand for small sizes of seamless copper tube which has recently occurred, due particularly to the rapid growth of the electric household-refrigerator industry, has emphasized the superiority of phosphorized to tough pitch copper for the purpose of producing this commodity. In the manufacture of this material exceedingly heavy reductions by cold drawing are employed, customary practice involving as much as 90 per cent. reduction of cross-sectional area in four runs without intermediate annealing. Although this superiority has long been recognized by tube makers, no quantitative expression of it has heretofore been published. It is believed that the data herewith presented will serve this purpose. Recent investigators are not in agreement as to the relative mechanical properties of copper containing small amounts of oxygen as compared with copper containing sufficient oxygen to produce that condition known as tough pitch. Hanson, Marryat and Ford' found that "oxygen has a relatively small effect on the properties of copper." Johnson,2 on the contrary, states "it cannot be denied that it (tough pitch copper) is inferior, to deoxidized copper where severe mechanical manipulation is concerned." These authorities in the reports of their investigations, as might be expected from their conclusions, do not present data of a character requisite to a conclusive determination of the question.

Jan 1, 1927

Research and Development, once considered a luxury item only for well-heeled companies, has in the last two decades come into its own as a vital contributor to the fortunes of electronic, automotive, chemical and aerospace firms. In terms of money and talent poured into research, the mining industry is still far behind those industries. Although the U.S. Bureau of Mines, plus various mining and manufacturing firms and universities have made notable contributions to mining technology, the historical pattern of mining R&D shows a heavy reliance on the results of research in other industries. It is difficult to tell whether this pattern will change significantly in the future, but there is evidence of a growing awareness by mining officials that greater R&D efforts are going to be required not only to meet the nebulous demands of tomorrow's world but to meet the ever-present, mounting pressures being generated by "intra-metals" and "inter-materials" competition.

Jan 1, 1968

By F. W. Crossland

Losses of metal are often traced to incorrect pH/ORP signals in flotation, leaching, extraction, electrolysis, and precipitation processes, aggravated by pressure changes. IC Controls, a Canadian mining sensor manufacturer, developed a new superior pH/ORP sensor that stops metal losses, reduces environmental footprint and contributes to sustainability. The cause of incorrect pH/ORP signal is rooted in the reference. Reference junctions are designed to allow diffusion of reference chloride ions into the process but also allow process ions to diffuse into the reference. This development is important to mines and hydrometallurgists where sulphide, cyanide, ammonia and other poisoning ions are present in the process. These ions react with reference electrolyte components causing the signal to change, drifting from the correct process value. With fluctuating process pressure, ion in migration dilutes the electrolyte producing similar signal drifts. If process ion in-diffusion could be stopped, the pH/ORP signal would be accurate. IC Controls new pH/ORP sensor stops process ion in-diffusion, and remains accurate over long periods. New processes using higher pressure and fluctuating pressurized reactors will greatly benefit from stable pH readings. Similar to IC Controls' proven model 642 Mining pH sensor, our new model 647 contributes to sustainability through reducing disposal costs from waste reagents, lost metal and fewer used sensors.

Jan 1, 2014

By K. Sarveswara Rao

The present paper firstly describes some recent trends from literature on energy management via process intensification to arrive at sustainable technologies for aqueous processing of minerals, metals and materials. Secondly, the energy saving measures practiced in leaching, solid-solution separation, solution purification, metal and material winning and environmental aspects have been discussed. The emerging importance of interdisciplinary nature of hydrometallurgy for practical applications is also highlighted. With the above background, the present paper describes an overview of energy conservation and autoclave processes with a special reference to hydrometallurgical research activities of our Laboratory.

Jan 1, 2008

By David Lin

"Modal data from Red Dog Main Pit ores were collected and analysed on a size-by-size basis. The Main Pit data were compared to data from composite samples of Red Dog Aqqaluk ores. The data revealed that a large fraction of the sphalerite in the Aqqaluk baritic ore was tied up in sphalerite/galena binaries. This provided an explanation for its poor leadlzinc selectivity compared to Main Pit ores. The Aqqaluk vein ore exhibited levels of sphalerite/galena binaries comparable to that of Main Pit ores resulting in comparable lead/zinc selectivity.An attempt was made to correlate the modal and metallurgical data for Main Pit stockpiles. It was found that there was moderate correlation between the percentage of sphalerite locked in binaries with galena in the <C5>C6 size fi-action and sphalerite deportment to the leadconcentrate.INTRODUCTIONTeck Cominco’s Red Dog Mine in northern Alaska is one of the richest zinc districts in the world. Red Dog Mine has been in operation for over ten years and produces nearly 1 million tonnes of zinc concentrate per mum. Red Dog Mine is an open pit operation and current mining is conducted in the area known as the Main Pit. The Main Pit contains proven reserves of about 41 900 000 tonnes of ore grading 19.2% Zn and 5.2% Pb (Cominco 2000). To the north of the Main Pit is the Aqqaluk deposit. It contains probable reserves of 56 100 000 tonnes of ore grading 16.6% Zn and 4.1 % Pb. After the Main Pit has been exhausted, the Aqqaluk deposit will be exploited.The Aqqaluk deposit consists of three main geologic ore types: baritic, siliceous and vein. The siliceous ore type is dominant, representing 64% of the mineralisation. Composite samples of these ore types were created from drill core and batch flotation tests were performed on them. The flotation tests indicated that there were significant metallurgical differences between Main Pit ore and the Aqqaluk siliceous and baritic ore. The siliceous and baritic ores were found to suffer from poor lead/zinc selectivity (Lin 1999, G&T 1999). It was suspected that there were problems with the original Aqqaluk composite samples, thus a new set of composite samples were created and batch flotation tests were conducted again. In this set of tests, the new baritic ore still suffered from leadlzinc selectivity problems, but the new siliceous ore provided excellent metallurgical results. A summary of the flotation results is given in Table 1. Stockpile 132, which is typical of Main Pit ore, is given for comparison purposes. The mineral suite at Red Dog is relatively simple. The ore consists of galena, sphalerite and pyrite in a silicate matrix. The low zinc recoveries of the baritic ore were largely due to sphalerite losses to the lead concentrate."

Jan 1, 2002

By James R. Finlay

At first blush one is tempted to say that iron-mines are like any other mines, and that principles governing miniug-property in general will apply to them. But there are certain considerations which seem to repay reflection. Gold and copper are more or less independent of transportation. The proof of this is that those metals are profitably mined and shipped from the remotest corners of the earth. Their value is determined by the cost of production on the ground. This is quite true of gold, not quite so true of copper, not at all true of iron. If New York were a. fishing-village and Chicago a swamp, Calumet & Hecla might still be a bonanza. The main element of its value is the 60 lb. of fine copper per ton which it produced for years. But the Mesabi Range is absolutely dependent upon the industrial activity in the United States. Iron-manu-facture in Europe would give it no value whatever. If Chicago and New York had a population of Peruvians or Hindus, the Hull-Rust mine would be as worthless a bit of landscape as any tundra in Alaska. I have discussed these facts more or less casually and dimly in my book on the cost of mining and in my report to the Tax Commissioners of Michigan.1 I shall try here to bring them out in more detail. I have already referred to some differences in the problem of mining as between the more precious metals, e.g., gold, and the less precious and more abundant minerals, like iron and coal; but it is interesting to note that the literature of the eco-

Jan 1, 1914

By Greg Mclellan, Mark Johnson, John Pepper

Several large quarrying projects recently occurred in Miramar, Florida. These were closely monitored by the Seismologist of Record and Broward County in accordance with County and City regulations. In addition to this monitoring, the City of Miramar employed The Pepper Engineering Group, Inc., to provide additional spot check monitoring and to review the records of the other two parties on a routine basis. Broward County ordinances require that the location of each shot and the nearest protected structure be recorded along with seismograph measurement of each shot at the nearest protected structure. The positions of the blasts and nearest protected structures were determined using GPS. The blast vibrations were measured by seismograph. Over 600 shots, which are the subject of this study, were measured both by the County, the Seismologist and, on many occasions, The Pepper Engineering Group. As such, the vibration data was constantly cross-checked for consistency. The blasting contractor also provided blast designs for each shot. In this paper, the measured vibrations are plotted in terms of Resultant Peak Particle Velocity (RPPV) versus Scaled Distance (SD) on logarithmic scales. The data curves are fitted with least squares and upper 95% and 99% prediction limits are provided. Equations are presented to predict the RPPV based on scaled distance and prediction level using power fits. Statistical information concerning the derivation of the various limits is presented. The raw data used to develop this paper, along with other information concerning the shots, will be posted on the Internet for use by other researchers.

Jan 1, 2000

By J. M. D. Wilson

The literature relating to binders in iron ore pelletizing is reviewed from the point of view of their established or proposed bonding mechanisms in green and dry pellets.

Jan 1, 1981

By M. A. Mahtab, A. S. Burgess, R. G. Charlwood, P. O. Sandstrom, J. L. Ratigan

"Addressing a current operating and environmental concern, this paper first presents an overview of the design program for an underground radioactive waste storage vault. It then reviews the construction, operational and thermal-mechanical aspects of such a project. The relevant experience from major underground construction projects is reviewed and the paper concludes with brief comments on the design-oriented research and development requirements . 1. IntroductionA program to develop techniques for the ultimate disposal of high-level radioactive waste into geologic formations was announced by AECL in 1975 (Tamrnernagi, 1976), and is discussed more fully in a later document (Boulton, 1978). Our paper summarizes the studies caried out, as part of the AECL waste management program, by the authors and associates on the development of design concepts for a vault situated in crystalline rocks of the type present in the Canadian Shield.The design studies have been carried out in three phases, the elements of which are described in Section 2.1 (also see Fig. 1). The general vault designs are presented in Section 2.2. These provide for emplacement of either immobilized fuel or solidified reprocessing wastes in a room-and-pillar facility at a depth of 1,000 m.Section 3 reviews the principal design considerations from the construction, operation and thermal-mechanical response aspects. The concepts have been studied in both temporal and spatial domains, and the requirements and responses assessed in each as appropriate.Section 4 briefly reviews the availability of relevant experience from previous major underground construction projects. Finally, in Section 5, brief comments are given regarding design-oriented research and development requirements."

Jan 1, 1980

By Ian E. Efford

The paper gives an assessment of Canada&apos;s energy supply-and-demand position, the current situation and projections into the future, as well as a review of some alternative energy futures for Canada. The main elements of Canada&apos;s energy strategy for the period 1977-1990, with particular reference to the role of energy conservation, are discussed, leading in to the development of the national energy conservation program.

Jan 1, 1977

By Yoshio Hiramatsu

In Toyoha mine near Sapporo, the ground temperature is very high, perhaps due to inflow of hot mineral water, the origin of which may be rock masses intruded by the igneous activity in the Tertiary period. The rock masses are found about 2 km east of the mine, their temperature being estimated at from 770 to 870 K at a depth of 3 km. In this mine several veins bearing zinc and lead ores have been mined down to the depth of 300 m from the level of the main entry, of which altitude is 551 m above the sea level. Formerly no attempt was made at development of the deeper part of the mine than the 350 m level from the main entry. Let us indicate hereafter the levels in this mine in such a way that the level 300 m deep from the main entry is denoted as 300 mL. Since 1974, however, the 450 mL of Tajima vein has been developed by deepening No. 5 Shaft to, and by driving drifts in the level. Much hot mineral water has been flowing into the drifts from rock. After twenty-eight months from the beginning of development, the total length of excavation amounted to about 1300 m. The success in development so far may be attributed to cooling rock and air with chilled water and to adopting heat-resisting explosives and detonators. This cooling costed very much and for further development in this level a more effective and economical cooling is desired if possible. To obtain fundamental data for designing an economical cooling, the authors investigated, as a preliminary study, the heat balance in the main drift of 450 mL, by measuring the temperatures of air, rock, hot mineral water, the rates of flow of air and water and so on, in August 1976. They are now carrying out continual measurements of the variations in rock temperature, air temperature and humidity with time. The present paper describes the details of the preliminary study.

Jan 1, 1980

By José Cáceres

Mine To Mill? ? Carlisle(1954) ?The economic of a fund resource with particular reference to mining?. ? Steine(1978) ?Coarser grind may mean lower metal recovery but higher profit?. ? Metalica (1999) ?Mine Plant Integrated Planning?. ? JK (2002) Mine to Mill Strategic Planning ? Camus, Kelebek (2002) ?Management of Mineral Resources: Creating Value in the Mining Business?. ? Caceres (2003) ?Integrating Milling Parameters in the Mining Planning?

May 1, 2006

By C. Takano

The integrated iron and steelmaking industry generates large amounts and many types of solid dusts and sludge, at different phases of the production. Within these are: sludge of the Blast Furnace; coke fines; fine and coarse fractions from oxygen converters; sludge from water treatment at rolling mill unit; and others. In this paper the above dusts and sludge were physically and chemically characterized. The obtained results allowed defining self-reducing pellets using these materials. The high temperature behavior of the pellets were evaluated. Good results, with no decrepitation and swelling, and high yield of reduction, show that it is feasible to recycle them, as self-reducing pellets, in oxygen steelmaking converter.

Jan 1, 2001

By H. L. James

THIS paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4°; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas.

Jan 1, 1947

By Blandford C. Burgess

Mica is an orchid among minerals. It is formed in pegmatites, one of the most bizarre of igneous formations, and is exceeded by few other minerals in the perfection it may attain as to size, color, and cleavage. First used for window glazing, as an ornament and article of trade, it has become one of the most essential insulators of electricity, heat, and shock. Most internal combustion engines use mica condensers or capacitors and such machines of war as planes, tanks, and submarines are immobile without it. The original manuscript of this guide was written in April 1943 at the peak of war emergency. It was not used because shortly thereafter a decision was made to buy on a one price basis eliminating differentials for both quality and size. This is now presented with the thought that from the standpoint of preparedness we can only consider another war imminent and every effort should be made to set up in usable form the experience gained during the Second Morld War. Colonial Mica Corp. was set up by Metals Reserve Co. as a wholly owned government agency to encourage production of domestic mica and to purchase it. It soon became the exclusive buyimg agency for such mica. The writer as Southern Manager called on all the private agencies buying mica to assist in formulating buying policies, methods, and prices. A meeting was held for that purpose in Asheville, N. C., July 20, 1942. In the general discussion the first two hours of the meeting it was decided that the following factors should be considered in pricing strategic mica: clearness, flatness, trimming, color, classification (size and quality), free splitting, hardness, and air inclusions. Most of the mica miners have been buying strategic mica, according to the mine, as No. 1, No. 2, or Nos. 1 and 2 combined. In addition to these grades of strategic mica they have been buying three lower grades of mica, electric (vegetable-stained), black-spotted and black-stained. A number of mines were named one by one and the buyers present gave their opinions as to the basis they would use in buying the sheet mica from each. It was suggested that in addition to the prices already published, prices be posted up to 10 pct higher for special quality and preparation and prices be posted 25 pct lower than the published prices for the lowest acceptable grades of strategic mica, giving the buyers authority to make intermediate prices according to the quality and preparation. It was thought desirable at the same time to announce prices for nonstra-tegic mica where such quality is being obtained in mines producing strategic mica and where it would be necessary to take the output in order to get the strategic mica. It was also suggested that the price of electric and black-spotted mica be 50 pct below the price of the lowest grade of strategic mica and the price of black-stained mica be 60 pct below the price of lowest grade strategic mica. The few experienced buyers available were employed but they were inadequate for the job and others had to be trained. All needed a guide or primer of some kind to attain systematic procedure and consistent prices in their respective buying areas. The Mica Buyers Guide was formulated for that purpose based on experience gained in the first six months of buying. The Preface to the original guide was as follows: The purpose of this guide is to serve as a text in training beginners and as a handbook for experienced buyers of the instructions which have been issued up to this time. At the meeting of prospective buyers last summer, it developed that the first essential to attain uniformity must be some kind of check sheet. Our "Mica Buyers Report" was developed for this purpose and forms the backbone of this guide. Price is determined according to size, quality and preparation. Size can be measured, but no system of measurement or machine has been devised which can be substituted for the trained eye of the buyer to deterrnine quality and preparation. Although the "One Price" system was instituted and the "Guide" not used, the buyers were required to continue making out a "Mica Buyers Report" (Fig1) with each lot of mica purchased. The form proved its value and there is no doubt that in another such emergency some similar form should be

Jan 1, 1950

By P. D. I. Honeyman, P. A. Faust

At the Miami plant of the International Smelting Co., Inspiration, Ariz., there are four reverberatory furnaces, all 120 ft. long. At present only one of these furnaces is in operation. It is operated as a wet-charge furnace, the charge being distributed for about 65 ft. down the furnace length. Usually this charge contains about 12 per cent moisture and runs 25 per cent sulfur, of which there is eliminated in the furnace from 25 to 30 per cent. The furnace is oil-fired, the fuel being burned in a battery of Cananea-type, low-pressure burners. The flame is kept short and conditions so adjusted as to obtain complete combustion within the furnace. The average furnace draft, taken through the verb arch, amounts to only 0.02 in. of H2O. Draft is purposely kept low to cut down infiltration through the flues and boiler settings, and control dampers are regulated to maintain this uniform condition throughout the charging as well as the smelting period. Hot gases discharge from the furnace uptake through a common header flue to the waste-heat boilers. The general layout and dimensions of the plant are shown in Fig. 1. Four Stirling boilers, two of class M-26 (713 hp.) and two class M-31 (850 hp.), serve the furnace. Three usually are sufficient to take care of normal operation, the fourth boiler being used as a spare when necessary. The distribution of hot gases to the various boilers is regulated by the dampers in the boiler exit flues. Normally the boilers closest to the furnace uptake would evaporate more water than do those farther away, but dampers are regulated so as to distribute fairly well the load between the several boilers. Steam from the waste-heat plant is delivered to the adjoining power house of the Inspiration company, where it is used both in the Nordberg blowing engines and for electrical generation. Steam pressures and temperatures recorded are those in the main power-plant header and are thus inclusive of all losses in about 500 ft. of 10-in. line. Steam for smelter heating and auxiliary use is taken from the main waste-heat header, is reduced to 125 lb. and distributed through separate lines. Boiler feed water is supplied by the power plant and consists of returned condensate, augmented to a large extent by make-up water

Jan 1, 1934

By P. P. Knight

The Parkes Process is an important step in the pyrometallurgical refining of lead bullion and it is estimated that more than 50% of the Free world&apos;s primary silver production is processed by this route. The metallurgical efficiency of the process can have a significant impact on the overall refining costs, particularly with regard to zinc consumption and the costs of working up the silver-rich crusts?. Several authors have used mathematical or graphical methods in order to calculate the minimum required zinc additions and to study the merits. of alternative. operating procedures, but these methods are of necessity very cumbersome and are only able to deal with relatively simple systems. The paper explains how a computer model was developed which simulates the Parkes Process accurately and can predict the effects of changes made in operating methods. Examples are given of some of the findings and their relevance to the practical conduct of the process is? discussed.

Jan 1, 1990