Search Documents

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth, W. L. Finlay

Titanium with up to 7.5 pct Al forms single-phase a alloys that are work hardening, not heat treatable, and ductile as welded. The high aluminum Y phase alloys are not usefully ductile, despite their low hardness, but they have excellent oxidation resistance and hot hardness. LITTLE has been published on the effect of aluminum on the mechanical properties of titanium, despite the fact that two of the first four commercial alloys released by titanium alloy producers contained aluminum as an important alloying ingredient. These were both a-ß type alloys, one containing 4 pct A1 and 4 pct Mn and the other containing 3 pct A1 and 5 pct Cr. However, neither of these alloys reflects the true alloying nature of aluminum, since each contains important amounts of the ß-stabilizing addition, manganese or chromium. In a previous publication on the constitution of Ti-A1 alloys,' the authors showed that aluminum had a high solubility in a titanium and was strongly a stabilizing in nature. About 25 wt pct A1 is soluble in a titanium at room temperature. With as little as 5 pct added aluminum, the a transus temperature is increased from 882" to 970°C, and the correspond- ing ß transus to 995°C. The first intermediate phase in the Ti-A1 system is the ordered face-centered tetragonal TiAl phase, which extends from 34 to 46 wt pct Al. The present paper presents hardness data over the entire titanium-rich region of the system, through the TiAl phase, and mechanical property data on the alloy range capable of being fabricated. Methods of Investigation The materials used and general preparation of alloys, as well as experimental techniques used in the investigation of Ti-A1 alloys, have been adequately described.' Briefly, the preparation consisted of arc-melting the desired amount of high purity aluminum (99.99 pct purity) and iodide titanium (maximum hardness 100 Vickers, as deposited) together on a water-cooled copper hearth under a partial pressure of argon. The resulting button ingot was of such form that it could be fabricated without further treatment. All work was done using ingots weighing 10 to 15 g, which were hot-rolled to strip form whenever possible. Tensile samples were 3.25 in. long, 0.5 in. wide, and 0.040 in. thick, with a reduced section 1.25 in. long by 0.250 in. wide. The gage length used was 1 in. Electrical strain gages mounted on the

Jan 1, 1954

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982

By William P. Blake

The mineral, garnet, is a common associate of copper-ore in the southwestern portion of the United States. This association may be observed on a large scale in southwestern Arizona, in southern New Mexico and in Sonora, Old Mexico, especially at El Cananea, and at Nacozari. At other localities in Mexico the general occurrence of garnet " as a contact metamorphic mineral" in the copper-deposits of the Cretaceous limestone is noted by José G. Aguilera.1 It is usually found at the contact of this limestone with diorites, granites, etc., at numerous mines. The same authority also cites the occurrence of garnet in metamorphosed Cretaceous limestone alongside of diorite dikes in association with iron-ore. Other foreign examples are found in the Banat and Servia, at Rezbanya in Hungary, and Offenbanya in Transylvania, and at Bogoslovsk in the Urals. In New South Wales, at Broken Hill, the gangue in the Proprietary mine is chiefly garnet, with quartz, opal and rhodonite.2 Also, in a recent paper by George Smith, entitled, " The Garnet-Formations of the Chillagoe Copper-Field, North Queensland, Australia,"3 it is shown that in the copper-field of Chillagoe, Australia, where there are many lode-formations, about one-half of the number are garnetiferous, and many of this garnet-type are associated with magnetite, which is regarded as of analogous origin. The two minerals are found merging imperceptibly into each other. These examples suffice to show the very general and wide distribution of garnet as an associate of copper-ore. In addition to the localities already mentioned as known in Arizona may be mentioned the copper-mines and occurrences

Jan 1, 1904

By T. Sreenivas

This paper describes results of laboratory studies on recovery of dissolved uranium values from alkaline leach slurries of a medium-grade uranium ore from Gogi (Karnataka, India) using the resin-in-pulp (RIP) process. Besides anionic carbonate complex of uranium, the other major ionic constituents of the leach solution are CO32-, HCO3-, SO42- and MoO42-. The total dissolved solutes (TDS) are about 45 g/L. Various commercially available strong bases anionic resin-in-pulp (RIP) grade resins ? both macroporous and gel type, were studied with respect to their loading capacity. Parametric variation studies were then carried out with the short-listed resins. Results of the semi-continuous counter-current extraction and elution tests indicated extraction efficiency of about 98% and practically complete elution of the loaded uranium values with NaCl eluant using a gel type polystyrene based resin grafted with quaternary ammonium ion. Keywords: uranium, hydrometallurgy, ion exchange, resin-in-pulp

Sep 1, 2012

By N. P. Kripakov

Results of a complex three-seam interaction analysis in a western U.S. coal mine are presented. The physical situation simulated by the models represents the development of a set of entries underneath two previously mined seams with all three seams in proximity to each other. The layout and the geometry of the remnant pillars in the upper seams were nonuniform and not always directly superimposed over each other, creating a very challenging modeling problem. The U.S. Bureau of Mines' MULSIM/PC computer code was upgraded and enhanced to perform the required three-seam interaction calculations. Analysis was limited to simple linear-elastic assumptions as only peak stresses were required. Results clearly indicated that stress concentrations in the lower seam increased approximately 100 percent when compared to cases simulating no extraction in the two upper seams. These stress concentrations generally occurred in zones directly below points of highest abutment pressures in the upper seams. Overall, the model results compared favorably with actual documented observed behavior where roof failures were known to have occurred.

Jan 1, 1996

By D. J. Carney, J. Chipman, N. J. Grant

G. Derge—With the development of this last weapon, there is not much of a chance for hydrogen. It is certainly a very interesting paper, and it gives us more confidence in sampling liquid steel for hydrogen than we have ever had before. This satisfactory work gives considerable confidence to all of the chilled methods of sampling which should be more or less successful depending upon the degree of chilling obtained. J. T. MacKenzie—How do you handle a nonmagnetic specimen in that device? D. J. Carney (authors' reply)—I left that out in going over the analytical procedure. For the 18-8 steel, what was done was to get some iron wire which was degassed. One turn of wire was made around the sample; it was inserted into the analytical apparatus, and that was enough to allow the magnet to pull the sample and drop it in the furnace. Other methods could be devised for this apparatus to do the same thing. This was just a quick method. C. E. Sims—This method of sampling and analysis is very ingenious, and the results obtained attest to a satisfactory degree of accuracy. It was noted in the paper that the samples are satisfactory only when there is a complete absence of pipe. This should be empha- sized, particularly in view of the fact that they are cut off under water. Some reservations are held in regard to the adequacy of the method of sample storage prior to analysis. Cooling on dry ice undoubtedly slows down the rate of diffusion to a marked degree, and it obviously suffices when the analysis is made within a few hours. All of the samples, except some of high-nickel steels, were analyzed within 12 hr. It is still unknown how long this method would be safe. In the work at Battelle Institute, it was impracticable always to start analysis within 12 hr for various reasons. Some samples did not reach the laboratory for several days, and some were held as long as a month before analysis. During this period, they were held over mercury, and the gas evolved at room temperature was collected and analyzed. It should be mentioned that both the mercury and the container must be kept very clean.

Jan 1, 1951

By Elbert Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By J. J. Demeter

As part of its work on converting coal to fluid fuels, the Federal Bureau of Mines has been studying the synthesis of liquid fuels from carbon monoxide and hydrogen by Fischer-Tropsch synthesis. A fluidized bed of nitrided, fused-iron catalyst has been operated successfully to produce high yields of oxygenated compounds. Trouble-free operation continued for over 800 hours, and the test was terminated voluntarily. About 85 percent of the fresh feed was converted when the unit was operated at a space velocity of 500 hr.-1, a 12:1 recycle-to-fresh-feed-gas ratio, a 300-p. s. i. g. pressure, and a temperature of 252° C. When operating at a fresh-feed-gas space velocity of 1,000 hr.-l and a 9:1 ratio of recycle to fresh gas, conversion of fresh feed was 68 percent, and the product yield was 235.9 grams per cubic meter of synthesis gas converted. The oxygenate and C5 and heavier hydrocarbon yield was 110.6 grams per cubic meter of gas converted, 83 percent of this was oxygenates. The atom ratio of N:Fe of the catalyst, initially 0.455, decreased to 0.288 by the end of the 800-hour experiment. Nevertheless, the yield of oxygenated compounds per cubic meter of H2 + CO converted at the end of the run was approximately the same as that obtained 500 hours earlier with identical operating conditions. X-ray analysis of the discharged catalyst indicated that only ?-iron carbonitride was present. Sieve analysis of the discharged catalyst indicated that only 2 percent of fines was produced during the reduction, nitriding, and synthesis.

Jan 1, 1959

The P49 Shaft, Hilton Mine, was sunk and equipped for Mount Ise Mines Limited by con- tractors Cementation - Thiess Joint Venture. The leached siltstones to a depth of 150m were known to contain large volumes of water. These siltstones were cored and tested in the laboratory. Field results confirmed that cement grouting was relatively ineffective but that chemical grouting was effective. The Sm diameter shaft was sunk to a depth of 1040m. Weak strata to the full depth re- quired continuous temporary support by rock bolts and mesh before the concrete lining was poured, and made sinking conditions difficult. After completion of the shaft sinking the headframe was redesigned and modified to allow shaft equipping as a combined service and hoisting shaft with seven compartments. The shaft steelwork was designed and fab- ricated for service with high speed conveyances operating under corrosive conditions. The steelwork, weighing approximately 1500 tonnes, was installed to a high degree of accuracy which required guides not to depart from true verticality by more than 2mm over any 5m, or 15mm over the full shaft depth.

Jan 1, 1976

By John E. Litz

Since the 1974 introduction of catalytic converters to automobiles in the United States, more than 150,000 kg (5,000,000 oz) of platinum, palladium, and rhodium have been used in the converters. An estimated 8 to 10 million converters are being used annually in the United States, each containing from $5 to $15 of PGM metals. In addition, use of converters is beginning in Europe which will significantly increase the quantity of PGM used. Two basic types of catalysts for converters are being used: pellet and monolithic. The pellets are small, discrete spheres or cylinders of gamma-alumina coated with platinum group metals, Figure 1. The monolithic are honeycombs of a cordierite, A13(Mg,Fe)2Si5AlO18, base coated with gamma-alumina and subsequently with platinum group metals, Figure 2. Pellet catalysts are being used by General Motors and American Motors; whereas Ford and Chrysler are using monolithic catalysts. The table below compares the PGM content and value of the catalysts.

Jan 1, 1986

By Milorad Cirkovic

Kinetics of copper concentrate oxidation in roasting processes in a fluidized bed reactor has been studied at temperatures between 600°C and 720°C using particles of 0.038 to 2.5 mm in average size. The analysis of composition of samples has been done by chemical methods. Phase composition has been determined by Siemens X-ray equipment with Cu anticathode and Ni filters at a voltage of 40 kV and a current of 18 mA. The content of sulphur has decreased from 33.23 to 19.02 mass percent with the increase of temperature, but the content of Fe304 has increased from 0.15 to 17.14 mass percent. The new mechanism of copper concentrate oxidation in a fluidized bed reactor is proposed in this study. It has been shown from the mathematical model that the velocity of oxidation of copper concentrate between 600°C and 720°C is virtually controlled by the rate of diffusion of 02 through the layer of reaction product.

Jan 1, 1999

By D. Bai, F. Hamad, S. Abraham

For the integrity of welded structures such as pipelines, the toughness of the heat-affected zones (HAZ) is an important property. This property is often specified in terms of Charpy V-notch (CVN) impact toughness and determined by the standard test method. An experimental study has been conducted in an industrial laboratory to measure the impact toughness of the coarse grain heat-affected zones (CGHAZ) of an X80 line pipe material. The field girth welding conditions in terms of heat input were simulated, together with special edge preparation to improve the targeted testing of the CGHAZ. The effect of toughness of the neighboring regions, in particular the weld metal, on measured impact toughness of the CGHAZ was investigated. The fracture paths of the CVN tested samples were examined by both optical and scanning electron microscopy. The deviation of segments of the fracture path into the weld metal was found to have a significant effect on the measured impact toughness of the CGHAZ.

Jan 1, 2005

By M. Misra

The dispersion of oily collector has significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. However, such dispersion and reagent addition techniques are invariably inadequate and non-selective. A new collector utilization technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This new technique involves atomization of the collector into the gas stream. Under these circumstances an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the gas phase (continuous with respect to oil) and the gas phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de-facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and most significantly increases the flotation rate of ultrafine coal. Furthermore, atomization of collector/frother combinations yielded improved flotation yields and maintained near uniform froth levels which is a desirable feature in coal flotation. In addition to flotation experiments, microscopic examinations of the attachment of oil-coated bubbles at a coal surface were conducted by attachment-time and contact-angle measurements. The oil coated bubbles attach at significantly faster rates and with a higher contact angle than do oil free bubbles.

Jan 1, 1987

By C. A. Mitke

During September, 1911, the fire area in the Lowell mine continually increased and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft mere found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2, CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97", and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2. Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were tested for air circulation and air tightness and the injector mas tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering these different tests, are illustrated in the catalogue and circulars of the company. After the above tests had been made on the oxygen apparatus, the men still complained about leaky helmets. Small quantities of gas entered the helmets and could not be detected by these methods. The

Jan 1, 1914

By A. D. Pittuck

Refractory minerals .containing uranium and columbium have been successfully treated at Queen's University, Kingston, to produce high-grade concentrates. Recoveries of over 90 per cent of the uranium and columbium have been obtained when treating concentrates containing euxenite, fergusonite, betafite, and pyrochlore. The processes ?consisted -of leaching the columbium with hydrofluoric acid, and the uranium with nitric acid, sulphuric acid, or sodium carbonate solutions. The leach liquors were extracted with organic solvents from which the values were stripped and precipitated, producing final products assaying 45 to 55 per cent Ob2O5 and 60 to 70 per cent U3Os.

Jan 1, 1958

The sulphide ores of the Kalgoorlie goldfield have long been looked upon as' refractory, involving special metallurgical treatment. For many years two kinds of treatment have been practised-(l) wet treatment, including fine grinding, amalgamation or concentration of the free gold, concentration of the sulphide minerals with subsequent roasting and cyanidation, and cyanidation or bromo-cyanidation of the residue from the concentrating operation; (2) dry-crushing of the ore and roasting the whole of thecrushed ore, amalgamation of the gold in the calcine during fine grading, followed by cyanidation. The wet treatment was advanced a stage further when, in 1929, the Lake View and Star Ltd. adopted large scale flotation. As a consequence, however, further metallurgical problems were introduced. This paper covers the investigation, ,of one of the most prominent of these problems.Flotation preceded by strakes was satisfactory to a point.The flotation concentrate consisted largely of auriferous pyrite and tellurides, and the gangue minerals in the concentrate were practically barren.Several sources of loss of gold values were, however, found to be associated with this circuit, viz.-(a) There was the loss of gold in the flotation tailing.(b) Loss by dusting during roasting of the flotation concentrate.(c) Loss of gold in the cyanided residue.

Jan 1, 1937

By D. M. Conner

An innovative patented process has been developed to convert high volume wastes--fly ash from coal-fired power plants, municipal solid waste (MSW) ash from incineration, solids from waste water treatment and paper mill sludge into a high value and environmentally benign product in the form of a lightweight aggregate. Lightweight Aggregate is widely used in the building construction industry in the United States, Europe and some Asian countries. This paper will present the development of the process, the process itself and details on the first commercial scale plant. The commercial plant is owned and operated by Wisconsin Electric Power (WEPCO).

Jan 1, 1997

By Paul Mitchell, Clive Potter, Miles Watkins

Meldon Quarry is a seemingly rare occurrence of acid rock drainage (ARD) in a quarrying operation.4 With surface waters discharging to a tributary of a salmon-bearing river, it is subject to stringent discharge conditions. The quarry predates effective environmental management, and preventative, control and treatment measures were not implemented until relatively recently. However, retrospectively implementing standard preventative approaches at the site is costly, technically difficult and of uncertain benefit. This paper overviews the recent site history and introduces data from a demonstration by KEECO (UK) Limited of its Silica Micro Encapsulation (SME) water treatment technology.

Jan 1, 2000

By M. D. Bath

Minproc Engineers Inc. (Minproc) recently completed the construction and start-up of a process facility to treat 14,000 t/d of gold-silver ore at Kori Kollo, Bolivia. The comminution circuit consists of crushing and SAG-ball mill grinding. Breakage characteristics of the ore were determined and a circuit model developed. This enabled variations of the circuit to be simulated, and evaluated in terms of predicted performance to provide the criteria for final engineering design. Subsequently, analysis of the operating circuit provided data for circuit model-fitting. The validity of the original model and circuit performance predictions are discussed.

Jan 1, 1994

By S. H. Ash

More than 100 minerals are mined and processed in the U. S. Management and labor have negotiated wage-scale agreements that have balanced wages and affected cost of labor in such a manner that comparisons can be made of transportation costs. Transportation of materials underground has become of vital importance. This report describes underground haulage methods and equipment, presents cost analyses, and discusses future plans for underground transportation in metal mines. It does not cover hoisting in shafts or slopes by cage, skip, or cars. Advancements have been made by the metal mining industry in lowering transportation costs in several mines, making it possible to mine orebodies or portions of orebodies not considered economically recoverable a few years ago. Numerous reports have been written on transportation at metal mines; this report covers recent haulage at some representative mines throughout the U.S. The term metal mine is used to include all noncoal mines from which up-to-date information was obtainable.

Sep 1, 1956