Search Documents

By Fred T. Towne

There are a number of air classifiers manufactured throughout the United States and the rest of the world. The classifiers manufactured by Alpine, A. G. of Augsburg, Germany, are unique in their abilities. It is this uniqueness that I wish to delve into and in this respect we will limit this discussion primarily to the classifiers as manufactured by Alpine. It has been reported in the past that these classifiers were introduced into the. United States in the late 50's. Until the introduction of the Alpine Classifiers, air classification seldom produced a satisfactory fractionation of a product below 45 microns (325 mesh) or above approximately 22 mesh. It has been a common practice to classify fine materials which used water as a carrier medium The use of centrifuges are today producing thousands of tons of finely partitive powders in the very small particle size range. The use of centrifuges in connection with wet grinding mills has increased the rates of production of these mills considerably.

Jan 1, 1965

By Irwin R. Higgins, Joseph C. Milbourne

The selection of a suitable nitrate removal process depends on a variety of site-specific chemical and environmental issues. The dominant technologies for nitrate removal include biological denitrification and continuous countercurrent ion exchange. The decision to apply either of these technologies, or both together, depends on the nature of the waste water to be treated. Factors that affect the selection of the biological system include the feed composition and feed temperature. Ion exchange nitrate removal systems ere less sensitive to the feed composition but require disposal or destruction of the concentrated pregnant eluate. The paper discusses Tetra's continuous countercurrent ion exchange technology (CCIX™) and fixed film biological reactor, Denite®. The treatment of the ion exchange pregnant eluant is also discussed.

Jan 1, 1995

By S. S. Nadgauda, A. J. Hathaway

Typically, as long as the coal quality is within the specified range, electric utilities have used delivered cost of fuel per million Btu as the primary criteria for qualified coals when making coal-procurement decisions. Such an approach may not fully address the total cost of using different quality coals at a given plant. A practical and easy-to-build model is described for estimating plant-specific utilization costs for coals of different qualities. Examples are included to illustrate the modeling results for plants operated by two utilities. While the model has certain limitations, it does represent an improved method for evaluating coal bids, and, consequently, reducing generation costs.

Jan 1, 1990

By John Reilly

"INTRODUCTION Successful management of megaprojects, meaning delivery within budget, on time and according to expectations, is a fundamental requirement. Many projects have been successful, some have not. This paper reviews megaprojects1, drawn from the author’s projects over the last 50 years, with “lessons-learned” and a summary of recommendations that, if implemented, would improve megaproject management and delivery. Characteristics of these projects are summarized – including outcomes related to key factors such as politics, management, organizational structure, contracting methods, cost estimates, risk and other elements. The projects include the Washington D.C. Metro, Boston Southwest Corridor, LA Metro, Toronto Rapid Transit Expansion Program, BART San Francisco, MARTA Atlanta, London Underground and the Washington State Highway megaprojects – including the SR520 Floating Bridge and the Alaskan Way tunnel. Other projects that illustrate successful, innovative management and contracting methods include the Madrid Metro (low-cost delivery), the Sydney Northside Storage tunnel (outturn cost, alliancing) and the Lake Mead tunnel (working in partnership, risk management). KEY ISSUES A characteristic of megaprojects is that their complexity increases exponentially with size (Reilly 2010, Galloway et al. 2012). These projects are very visible politically, have many stakeholders who must be satisfied and generally span many years and political election cycles. To be successful they must meet expectations, function efficiently, and be delivered under, at or close to budget and schedule. There is a widely-based perception that large, complex projects are always delivered late, over budget and with problems. Specific examples include projects such as Tren Urbano in Puerto Rico – $1.28 billion over initial budget (+133%), the Silver Line Transitway Project in Boston – $286 million over budget (+90%), the London Jubilee Line Transit Project – 2 years late and £1.4 billion (+67%) over budget, the Channel Tunnel Rail Project – £3.7 billion (+80%) over budget, Denmark’s Great Belt Link rail and road link (54% over budget), the 2003 Woodrow Wilson bridge tender in Virginia (72% over estimate) and Boston’s Central Artery Project – several billion (perhaps 100%) over what would have been a realistic initial budget and years late (Reilly 2001c, 2004a; Salvucci 2003)."

Jan 1, 2016

Jan 1, 1945

By William Hanco Mamani

El Perú es el primer destino de inversión minera en Latinoamérica y el tercero a nivel mundial. Como tal, ha generado una creciente demanda de información referida al catastro minero y al tema geológico, vital para la identificación de los recursos minerales. Por ello, el inversionista necesita contar con información actualizada, accesible y de una fuente confiable para poder planificar sus actividades. En este sentido, el presente texto describe la importancia de Geotmin en la industría minera -en tanto sistema de información geográfica de última tecnología que desarrolla la interactividad de fácil manejo y compresión de la estructura de capas presentadas en el sistema, donde su principal base de datos se basa en un geodatabase con más de 40 capas de información.

Sep 12, 2011

By D. Harrington

WHEN the word gas is mentioned in connection with mining, almost invariably it is inferred that the explosive gas, methane, is in mind and that it must refer to coal mining. While it is true that methane occurs, or is likely to occur, in almost any or all coal mines, it is also a fact that the metal mines of the world have in them by far a greater variety of gases than have the coal mines. In many cases the gases in metal mines are as dangerous to individuals as the gases likely to be found in coal mines; in some instances the metal mine gases are even more deadly. The coal mine is more likely to have methane than the metal mine, in rare instances it may have high percentages of nitrogen or high carbon dioxide, or there may be a deficiency of oxygen where the air is confined in a blind end or in a sealed region; much more rarely there are found in coal mines in relatively small percentages, ethane, or other hydrocarbons with odor of ether, gasoline or kerosene, or there may be minute percentages of hydrogen sulfide. In time of coal mine fire or explosion, there is likely to be high carbon monoxide (4 per cent. or over in some cases) and if the coal contains much sulfur, there may be some sulfur dioxide in the fire fumes. In metal mines there are a number of cases of occurrence of methane and attendant explosions; some metal mines have appreciable percentages of the decidedly explosive hydrogen; in some metal-mining regions carbon dioxide flows into the mine, fills the workings and overflows just like water. In other regions, at many working faces there are high-temperature gases containing a mixture of gases of sulfur (sulfur dioxide, hydrogen sulfide and possibly SO3 in some cases) together with carbon dioxide and nitrogen, and the deadly hydrogen sulfide in lethal proportions is found in some high-sulfide metal mines at blasting time. Carbon monoxide constitutes a decidedly dangerous day by day hazard in connection with metal-mine blasting, because of the heavy charges of dynamite that are used and the use of fuse, which in burning gives off much carbon monoxide. The poisonous gas hazard is accentuated because of the relatively small openings where metal-mine blasting is done and to the inefficient ventilation of the usual metal mine.

Jan 1, 1930

By J. J. K. Daemen, C. Fairhurst

Two aspects of tunnel support design are considered, and for both particular attention is paid to the influence of rock failure around the tunnel on the loads developed on the supports. 1) In general it has not been possible to extend analytical methods for the study of rock failure around tunnels to three dimensions. As a consequence it was not possible to calculate either the influence of the face or the actual sequence of support loading as the face advanced. The finite element method made this extension possible. A simplified analysis of the influence of the face and of the sequence of support installation has been made. The influence of the original stress field and of the rock behaviour on the length of tunnel which can be left unsupported (related to the stand-up time) is shown. The degree to which a 2-dimensional analysis can be used to approximate the final support load is shown to be dependent upon the post-failure behaviour of the rock. 2) Tunnel support design requires a knowledge of the forces and of the -rock displacements which cause stressing and deformation of the support system. A 2-dimensional model incorporating a detailed representation of several support systems, of the rock behaviour in the broken zone and of the interaction between rock and support is given. The model allows the calculation of the stress distribution in the support. The significance of the relative stiffness of support and rock on the stresses developed in the support is shown.

Jan 1, 1997

By L. Mahony

This paper describes the design, construction and commissioning testing program for a laboratory facility at the School of Mining Engineering, UNSW, Australia, aimed at evaluating reinforcement tendon performance when subjected to shear loading. The project has been financially supported through the coal industry ACARP research initiative. The single failure plane design adopted in the test rig has been successful in allowing shear loading to be directly applied to fully installed (and where relevant, pre-tensioned) rock bolts. Initial results are extremely encouraging, and illustrate a significant axial component of load development as shearing takes place - particular in lower strength, softer material types. The paper also outlines future plans for use of this facility.

Jan 1, 2005

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth, W. L. Finlay

Titanium with up to 7.5 pct Al forms single-phase a alloys that are work hardening, not heat treatable, and ductile as welded. The high aluminum Y phase alloys are not usefully ductile, despite their low hardness, but they have excellent oxidation resistance and hot hardness. LITTLE has been published on the effect of aluminum on the mechanical properties of titanium, despite the fact that two of the first four commercial alloys released by titanium alloy producers contained aluminum as an important alloying ingredient. These were both a-ß type alloys, one containing 4 pct A1 and 4 pct Mn and the other containing 3 pct A1 and 5 pct Cr. However, neither of these alloys reflects the true alloying nature of aluminum, since each contains important amounts of the ß-stabilizing addition, manganese or chromium. In a previous publication on the constitution of Ti-A1 alloys,' the authors showed that aluminum had a high solubility in a titanium and was strongly a stabilizing in nature. About 25 wt pct A1 is soluble in a titanium at room temperature. With as little as 5 pct added aluminum, the a transus temperature is increased from 882" to 970°C, and the correspond- ing ß transus to 995°C. The first intermediate phase in the Ti-A1 system is the ordered face-centered tetragonal TiAl phase, which extends from 34 to 46 wt pct Al. The present paper presents hardness data over the entire titanium-rich region of the system, through the TiAl phase, and mechanical property data on the alloy range capable of being fabricated. Methods of Investigation The materials used and general preparation of alloys, as well as experimental techniques used in the investigation of Ti-A1 alloys, have been adequately described.' Briefly, the preparation consisted of arc-melting the desired amount of high purity aluminum (99.99 pct purity) and iodide titanium (maximum hardness 100 Vickers, as deposited) together on a water-cooled copper hearth under a partial pressure of argon. The resulting button ingot was of such form that it could be fabricated without further treatment. All work was done using ingots weighing 10 to 15 g, which were hot-rolled to strip form whenever possible. Tensile samples were 3.25 in. long, 0.5 in. wide, and 0.040 in. thick, with a reduced section 1.25 in. long by 0.250 in. wide. The gage length used was 1 in. Electrical strain gages mounted on the

Jan 1, 1954

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982

By William P. Blake

The mineral, garnet, is a common associate of copper-ore in the southwestern portion of the United States. This association may be observed on a large scale in southwestern Arizona, in southern New Mexico and in Sonora, Old Mexico, especially at El Cananea, and at Nacozari. At other localities in Mexico the general occurrence of garnet " as a contact metamorphic mineral" in the copper-deposits of the Cretaceous limestone is noted by José G. Aguilera.1 It is usually found at the contact of this limestone with diorites, granites, etc., at numerous mines. The same authority also cites the occurrence of garnet in metamorphosed Cretaceous limestone alongside of diorite dikes in association with iron-ore. Other foreign examples are found in the Banat and Servia, at Rezbanya in Hungary, and Offenbanya in Transylvania, and at Bogoslovsk in the Urals. In New South Wales, at Broken Hill, the gangue in the Proprietary mine is chiefly garnet, with quartz, opal and rhodonite.2 Also, in a recent paper by George Smith, entitled, " The Garnet-Formations of the Chillagoe Copper-Field, North Queensland, Australia,"3 it is shown that in the copper-field of Chillagoe, Australia, where there are many lode-formations, about one-half of the number are garnetiferous, and many of this garnet-type are associated with magnetite, which is regarded as of analogous origin. The two minerals are found merging imperceptibly into each other. These examples suffice to show the very general and wide distribution of garnet as an associate of copper-ore. In addition to the localities already mentioned as known in Arizona may be mentioned the copper-mines and occurrences

Jan 1, 1904

By T. Sreenivas

This paper describes results of laboratory studies on recovery of dissolved uranium values from alkaline leach slurries of a medium-grade uranium ore from Gogi (Karnataka, India) using the resin-in-pulp (RIP) process. Besides anionic carbonate complex of uranium, the other major ionic constituents of the leach solution are CO32-, HCO3-, SO42- and MoO42-. The total dissolved solutes (TDS) are about 45 g/L. Various commercially available strong bases anionic resin-in-pulp (RIP) grade resins ? both macroporous and gel type, were studied with respect to their loading capacity. Parametric variation studies were then carried out with the short-listed resins. Results of the semi-continuous counter-current extraction and elution tests indicated extraction efficiency of about 98% and practically complete elution of the loaded uranium values with NaCl eluant using a gel type polystyrene based resin grafted with quaternary ammonium ion. Keywords: uranium, hydrometallurgy, ion exchange, resin-in-pulp

Sep 1, 2012

By N. P. Kripakov

Results of a complex three-seam interaction analysis in a western U.S. coal mine are presented. The physical situation simulated by the models represents the development of a set of entries underneath two previously mined seams with all three seams in proximity to each other. The layout and the geometry of the remnant pillars in the upper seams were nonuniform and not always directly superimposed over each other, creating a very challenging modeling problem. The U.S. Bureau of Mines' MULSIM/PC computer code was upgraded and enhanced to perform the required three-seam interaction calculations. Analysis was limited to simple linear-elastic assumptions as only peak stresses were required. Results clearly indicated that stress concentrations in the lower seam increased approximately 100 percent when compared to cases simulating no extraction in the two upper seams. These stress concentrations generally occurred in zones directly below points of highest abutment pressures in the upper seams. Overall, the model results compared favorably with actual documented observed behavior where roof failures were known to have occurred.

Jan 1, 1996

By D. J. Carney, J. Chipman, N. J. Grant

G. Derge—With the development of this last weapon, there is not much of a chance for hydrogen. It is certainly a very interesting paper, and it gives us more confidence in sampling liquid steel for hydrogen than we have ever had before. This satisfactory work gives considerable confidence to all of the chilled methods of sampling which should be more or less successful depending upon the degree of chilling obtained. J. T. MacKenzie—How do you handle a nonmagnetic specimen in that device? D. J. Carney (authors' reply)—I left that out in going over the analytical procedure. For the 18-8 steel, what was done was to get some iron wire which was degassed. One turn of wire was made around the sample; it was inserted into the analytical apparatus, and that was enough to allow the magnet to pull the sample and drop it in the furnace. Other methods could be devised for this apparatus to do the same thing. This was just a quick method. C. E. Sims—This method of sampling and analysis is very ingenious, and the results obtained attest to a satisfactory degree of accuracy. It was noted in the paper that the samples are satisfactory only when there is a complete absence of pipe. This should be empha- sized, particularly in view of the fact that they are cut off under water. Some reservations are held in regard to the adequacy of the method of sample storage prior to analysis. Cooling on dry ice undoubtedly slows down the rate of diffusion to a marked degree, and it obviously suffices when the analysis is made within a few hours. All of the samples, except some of high-nickel steels, were analyzed within 12 hr. It is still unknown how long this method would be safe. In the work at Battelle Institute, it was impracticable always to start analysis within 12 hr for various reasons. Some samples did not reach the laboratory for several days, and some were held as long as a month before analysis. During this period, they were held over mercury, and the gas evolved at room temperature was collected and analyzed. It should be mentioned that both the mercury and the container must be kept very clean.

Jan 1, 1951

By Elbert Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By J. J. Demeter

As part of its work on converting coal to fluid fuels, the Federal Bureau of Mines has been studying the synthesis of liquid fuels from carbon monoxide and hydrogen by Fischer-Tropsch synthesis. A fluidized bed of nitrided, fused-iron catalyst has been operated successfully to produce high yields of oxygenated compounds. Trouble-free operation continued for over 800 hours, and the test was terminated voluntarily. About 85 percent of the fresh feed was converted when the unit was operated at a space velocity of 500 hr.-1, a 12:1 recycle-to-fresh-feed-gas ratio, a 300-p. s. i. g. pressure, and a temperature of 252° C. When operating at a fresh-feed-gas space velocity of 1,000 hr.-l and a 9:1 ratio of recycle to fresh gas, conversion of fresh feed was 68 percent, and the product yield was 235.9 grams per cubic meter of synthesis gas converted. The oxygenate and C5 and heavier hydrocarbon yield was 110.6 grams per cubic meter of gas converted, 83 percent of this was oxygenates. The atom ratio of N:Fe of the catalyst, initially 0.455, decreased to 0.288 by the end of the 800-hour experiment. Nevertheless, the yield of oxygenated compounds per cubic meter of H2 + CO converted at the end of the run was approximately the same as that obtained 500 hours earlier with identical operating conditions. X-ray analysis of the discharged catalyst indicated that only ?-iron carbonitride was present. Sieve analysis of the discharged catalyst indicated that only 2 percent of fines was produced during the reduction, nitriding, and synthesis.

Jan 1, 1959

The P49 Shaft, Hilton Mine, was sunk and equipped for Mount Ise Mines Limited by con- tractors Cementation - Thiess Joint Venture. The leached siltstones to a depth of 150m were known to contain large volumes of water. These siltstones were cored and tested in the laboratory. Field results confirmed that cement grouting was relatively ineffective but that chemical grouting was effective. The Sm diameter shaft was sunk to a depth of 1040m. Weak strata to the full depth re- quired continuous temporary support by rock bolts and mesh before the concrete lining was poured, and made sinking conditions difficult. After completion of the shaft sinking the headframe was redesigned and modified to allow shaft equipping as a combined service and hoisting shaft with seven compartments. The shaft steelwork was designed and fab- ricated for service with high speed conveyances operating under corrosive conditions. The steelwork, weighing approximately 1500 tonnes, was installed to a high degree of accuracy which required guides not to depart from true verticality by more than 2mm over any 5m, or 15mm over the full shaft depth.

Jan 1, 1976

By John E. Litz

Since the 1974 introduction of catalytic converters to automobiles in the United States, more than 150,000 kg (5,000,000 oz) of platinum, palladium, and rhodium have been used in the converters. An estimated 8 to 10 million converters are being used annually in the United States, each containing from $5 to $15 of PGM metals. In addition, use of converters is beginning in Europe which will significantly increase the quantity of PGM used. Two basic types of catalysts for converters are being used: pellet and monolithic. The pellets are small, discrete spheres or cylinders of gamma-alumina coated with platinum group metals, Figure 1. The monolithic are honeycombs of a cordierite, A13(Mg,Fe)2Si5AlO18, base coated with gamma-alumina and subsequently with platinum group metals, Figure 2. Pellet catalysts are being used by General Motors and American Motors; whereas Ford and Chrysler are using monolithic catalysts. The table below compares the PGM content and value of the catalysts.

Jan 1, 1986

By Milorad Cirkovic

Kinetics of copper concentrate oxidation in roasting processes in a fluidized bed reactor has been studied at temperatures between 600°C and 720°C using particles of 0.038 to 2.5 mm in average size. The analysis of composition of samples has been done by chemical methods. Phase composition has been determined by Siemens X-ray equipment with Cu anticathode and Ni filters at a voltage of 40 kV and a current of 18 mA. The content of sulphur has decreased from 33.23 to 19.02 mass percent with the increase of temperature, but the content of Fe304 has increased from 0.15 to 17.14 mass percent. The new mechanism of copper concentrate oxidation in a fluidized bed reactor is proposed in this study. It has been shown from the mathematical model that the velocity of oxidation of copper concentrate between 600°C and 720°C is virtually controlled by the rate of diffusion of 02 through the layer of reaction product.

Jan 1, 1999