Search Documents

[ ]

Jan 1, 2000

By M. L. Davis

The principal causes of many methane-gas explosions that have occurred in anthracite mines, especially in thick pitching veins, during recent years can be traced to lack of a satisfactory method of testing for such gas in areas adjacent to those in which blasting is to be done or other sources of ignition introduced. As coal-mine officials and inspectors are required to make examinations for methane in all accessible open workings, including high places, and permissible flame safety lamps have been used almost universally for making these examinations, considerable difficulty has been experienced in proper testing of atmospheres at elevations beyond the normal reach of the examiner, and resultant explosions have often indicated perfunctory tests. The accepted practice of testing for gas in voids or high places generally consists of raising a flame safety lamp, suspended from the end of a long drill, stick, or pipe, into the atmosphere to be tested. Disadvantages noted are: Action of the flame within the lamp cannot be seen readily when the lamp is more then 18 inches overhead, the flame will not be extinguished when less than about 4-1/2 percent of methane is present, and indications of small percentages of methane within the lamp may disappear entirely while the lamp is being lowered slowly to view; the examiner must usually be exposed unnecessarily to falling material; and the lamp may fall and be broken. Thus, the need for a more reliable, safe method of testing for gas in out-of-reach places is apparent. Several electrical methane detectors, tested and approved by the Bureau of Mines, have been used satisfactorily, though infrequently, for making the aforementioned gas tests. Some of these detectors employ a rubber aspirator bulb and rubber tubing of suitable length to draw the atmosphere from high places through and over energized parts of the detector. However, the original expense, susceptibility to damage, and awkwardness of tarrying these instruments in steep-pitch workings has precluded their general use in everyday examinations. Although not as efficient as the electrical detector for determining small percentages of methane or as reliable because of the limitations imposed by oxygen-deficient atmospheres, the modern per¬missible flame safety lamp can, it is believed, be used safely with the rubber aspirator bulb and tubing to greater advantage and with comparative reliability in testing for gas in out-of-reach places. Slight reference to this method of introducing air into a safety lamp is made in a Bureau of Mines publication of l921,2/ and it is quite possible that the method has been utilized in some manner by individuals in American mines during the intervening years. A similar method was used in connection with a nonpermissible Wolf flame safety lamp in at least one coal mine in Japan before World War II. A major change in the construction of this lamp would bar its approval by the Bureau of Mines. An American adaptation of the Wolf lamp, developed

Jan 1, 1954

By Leon Nelson

SEVERAL factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in. square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation.

Jan 1, 1937

By Klaus M. Hahn, Hermann Wotruba, Bernd G. Friedrich

"Due to an increasing demand for nickel and cobalt and the depletion of nickel sulphide deposits worldwide, the production of ferronickel from lateritic nickel ores becomes more significant. About 60 percent of nickel reserves are present in laterite deposits. Common production methods like acid leaching or smelting operations implicate high material and energy consumption. Physical processing methods are also not efficient, because of the fine microstructural intergrowth of the minerals carrying valuable elements such as nickel and cobalt. Due to the high energy consumption of metallurgical treatment of lateritic nickel ore (nickel grade: 0.8 - 3.0%, Co: 0.05 - 0.15%), the separation of waste material (about 75 - 85%) before the metallurgical treatment is desirable. Therefore, an alternative process has been developed, combining a pyro-metallurgical pre-treatment with selected mechanical processing methods. The developed process consisted of a selective pre-reduction and non-selective segregation of the contained metal phases in the first stage. By this, the properties of the metal carrying minerals were changed and could become subject to concentration by means of fine beneficiation processes afterwards. The parameters of the pre-reduction and segregation were varied and the pre-treated samples were examined concerning their efficiency of metalization grade and metal grain size. This paper describes the investigation of pre-treatment methods of a lateritic nickel ore. The pre-treatment and possible subsequent separation methods were examined with regard to the recovery of the valuable elements. Metalization grade was around 80% for both Ni and Co with metal phase grain sizes below 20 µm. Scanning electron microscopy revealed distribution of new metal phases not only on the reducing agent, but also on the “slag” material.INTRODUCTION Nickel laterites are characterized as strongly weathered regoliths with several zones containing reserves of nickel (Ni) and cobalt (Co). These laterites are formed on serpentinites and ultramafic rocks under climatic and/or tectonic conditions that have changed over time (Butt & Cluzel, 2013). The formation of Ni laterites is influenced by numerous geological and environmental factors. In general, there are three ore types named according to the dominant Ni hosting minerals: oxides, hydrous magnesia (Mg) silicates and clay silicates (Butt & Cluzel, 2013). The most Ni laterite deposits contain two of these ore types, usually an oxide zone and an either clay or Mg silicate zone. Distribution of these principal deposit types, their average Ni-bearing phases and mean Ni grade are shown in Table 1. A schematic profile of the different deposits based on the development on serpentized ultramafic rocks is given in Figure 1 (Butt & Cluzel, 2013)."

Jan 1, 2018

By John Marsden

Despite the recent pullback in metal and mineral prices, and the associated market adjustments, the mining industry is still facing a serious issue with the declining availability of graduate expertise. This is due to a combination of an aging workforce, retirements and retrenchments, coupled with a lack of suitably qualified graduates entering the workforce. The issue has certainly improved since 2004 when the industry picked up the rates of hiring graduate engineers and mining/mineral school enrollments picked up in response. This hiring effort has helped to cover the ?gap? years from about 1985-2000, when industry demand for graduates was particularly poor. However, the recent market pullback is likely to set back this progress, as recruitment and hiring wavers as a result of cost cutting measures and economic uncertainty. A key issue for the mining industry is how to ensure the survival and growth of relevant ?core? degree programs. Such programs include mining, metallurgical, mineral processing and geological engineering. The mining industry needs a healthy, high-level education program to ensure an adequate supply of appropriately qualified graduates for the mining industry. Two-thirds of the professionals entering the minerals industry who graduated within the past 40 years graduated prior to 1985. Since 1985, we have been living off the legacy of graduation classes from the mid-1970s and early 1980s. It is estimated that we have been producing graduates at approximately 40 to 50 percent of the sustaining rate since about 1985. Further growth in the domestic industry would increase graduate requirements significantly, and the export of U.S.-graduates to other parts of the world (as is currently occurring) also impacts the total graduate requirements.

By Ronald L. Sanders

The prevailing view of the coal mining industry by government officials is: "Tell everyone you're coming - Don't let anyone know you're there - And remove all evidence you have ever been there". Now the irony is that the government inspectors are just enforcing the law. The coal mine operators seem more interested in genuine reclamation than the inspectors.

Jan 1, 1979

By Ian M. Ritchie

Cementation or metal displacement reactions such as Cu2+ + Fe Cu + Fe2+ are among the oldest known hydrometallurgical reactions. They are still used in the recovery of some metals and in the purification of process liquors and waste water streams. However, they are often more complex than the stoichiometric reaction would suggest because they involve the simultaneous deposition of one metal onto a second which is dissolving. For example, sometimes a cementation will not take place, even though it is thermodynamically favoured. On other occasions, a cementation reaction will start but come to a halt as the depositing metal blankets the reacting surface. On yet other occasions, side reactions, catalyzed by the deposit, can be important. In this paper, the electrochemical basis of cementation reactions is described. The conditions for each of the complications encountered in these reactions are described and illustrated by examples drawn from a number of hydrometallurgical processes. The cementation reaction between activated carbon and gold thiosulfate is also briefly described, this reaction being unusual in that no dissolution of the carbon occurs.

Jan 1, 2003

By E. G. King

This publication presents original thermal data for a typical variety of perlite and supplies basic information for use in computing energy requirements in processes for expanding perlite. Perlite has been defined by Raiston 4/ as any silicious lava containing dissolved water in sufficient amount to errand into bubbles when the material is quickly heated to a suitable point in the softening range." The uses of expanded perlite in) the construction and ceramic industries have been discussed by Ralston 4/ and King. 5/ The work described here had a dual purpose: (1) It was desired to ascertain quantitatively, using a typical variety of perlite, just how firmly the contained water is held, and (2) it was desired to obtain basic thermal data sufficient for energy-requirement calculations in processes for expanding perlite.

Jan 1, 1948

Truly launched during the 1939-45 war, b¬,osted since by huge increases in demand for food, shelter and manufactures of ill kinds, petrochemicals have rocketed into prominence' all'oVer''th'e world and are accelerating to even greater heights.Manipulation of the hydrocarbons in petroleum or natural gas provides raw materials for a wid.e'variety of plastics, resins, detergents, rubbers, chemical intermediates, fibres and fertilisers. These in. turn.. go into a host of products essential to our way of life.A5 a source of chemicals, petroleum has achieved a high place. because of its abundance, relative.eheapness acid ease "f transport and because it can,be' economically processed.'If a nation's industrial' progress is measured by ' the ' modern yardstick of petrochemical production,'Australia has reasonto be proud, for it now has 1S petrochemical plants worth'156 million, either in operation or under construction.At several locations near Sydney and Melbourne, these plants produce petroleum ethylene, propylene, butadiene and benzene, or convert these building blocks into the three major thermoplastics (polyethylene; polyvinylchloride and polystyrene)-a.nd"S.B.R.synthetic" rubber. "A number bf other imr-ortant petrochemicals, including carbon black, and ammonia, also are made, or-planned...Most petrochemicals find application. in seven principal industries - rubber, fibres, detergents, surface coatings, automotive, agriculture and plastics. They play a .part in many other industries, including mining and metallurgy.In Australia, population growth,.an -incr.easing standard of living, greater industrial activity and the replacement of older materials all should considerably expand the markets for established petrochemical plants and lead to the introduction of new manufactures.Unless thwarted, these positive forces should propel petro-chemicals into a future glittering with promise;' ò 'However, some help for the infant industry seems needed if petrochemicals, while growing with the nation, are to contribute as they can to our national development.

Jan 1, 1962

By Shirley F. Colby

A continued rise in construction activity in 1941 forecasts further increases in the demand for building materials of mineral origin, Recent studies by the Bureau of Mines, United States Department of the Interior, reveal that sales of mine and quarry products and their derivatives as a class have followed the long-term trend of construction activity in the past and are benefiting now by the upswing in all types of building. At present most building materials of mineral origin are holding their own in the competitive arena. A few are slipping behind, but others have forged fax ahead. Prominent among those that have surpassed general construction activity since 1925 are sand, gravel, and crushed stone (used in concrete and road metal and railroad ballast) and cement. Both building stone and roofing slate have followed the building curve closely, although in the last few years sales of roofing slate have risen above the curve and sales of building stone have dropped below it. Clay products and building lime, on the other hand, have lagged behind the general procession. Gypsum sales likewise dropped behind, but during the last few years, this industry, thanks to the wider acceptance of its newer products, has staged a marked recovery so that it now stands in about the same relation to total construction activity as it did is 1927-25.

Jan 1, 1941

"Boston’s Central Artery passes beneath nine active railroad tracks carrying commuter and Amtrak trains into South Station, the City's busiest rail terminal. These railroad operations had to remain in service throughout the construction of the “Big Dig”. The solution was to jack the tunnel under the tracks, rather than build the tunnel by more conventional means.Jacking of utility pipes is fairly common, but jacking boxes as big as a highway had never been done in North America, until the Big Dig came along.Soil freezing was decided upon as a means of stabilizing the soil under the tracks. This allows the tunnels to be jacked into place without soil caving when the soil is excavated at the leading face of the advancing tunnel boxes. Hundreds of pipes were driven into the ground between the tracks. Inside the steel pipes were smaller plastic pipes. A freezing plant near the railroad tracks pumped refrigerated brine into the inner plastic pipes. The brine ran out the bottom of the inner pipe, flowed up to the top inside the outer pipe, and was re-circulated to the freezing plant and back again into the ground. Over several weeks the circulating brine drew the heat out of the soil little by little, and froze the ground outward from the pipes. Soil FreezingThe plan required the construction of jacking pits in which the tunnel boxes could be constructed, and from which they could be jacked forward to their final locations, as described in the accompanying article. Once the jacking pit was built and the tunnel box constructed inside the pit, crews made an opening in the headwall of the pit to allow passage of the tunnel sections, excavated about three feet of the frozen soil, pushed the tunnel box ahead, and repeated the procedure again and again."

Jan 1, 2003

By W. M. Pytel

The applicability of the beam theory in analysis of roof- pillar-weak floor interaction in partial extraction room-and-pillar mining is presented. The mine structure is modeled as an equivalent multi-indeterminate overburden elastic beam supported by elasto-plastic pillars; resting on a viscoelastic layer of immediate weak floor strata underlain by a competent rock mass. The developed analytical model was initially utilized to conduct sensitivity analyses of different variables affecting the mining system, such as the deformability of coal and weak floor strata, thickness of weak floor strata, number of pillars in a panel, width of pillars, width of panel etc. These analyses were then extended to three overburden strata - coal pillar - floor strata lithologies typical of active coal mining areas in Illinois.

Jan 1, 1989

By W. M. Haffner, S. L. Borek, H. M. Edenborn, R. W. Hammack, D. H. Dvorak

The conceptual designs of three new applications for the biogenic &S treatment of metal- containing waters are presented. These include: 1. the treatment of a circumneutral-pH ground water containing Zn and Cd using limestone as an alkalinity source, 2. a two-step treatment process where toxic heavy metals in contaminated ground water are recovered separately from nontoxic metals to lessen disposal costs, and 3. a copper recovery process that may be a low-cost alternative to solvent extraction/electrowinning or cementation for dilute copper leach liquors. Preliminary results of initial field testing are discussed

Jan 1, 1995

By Arne Landsberg

Accessory metals, although valuable resources, present possible environmental concern in the smelting of base metals. The Bureau of Mines, U.S. Department of the Interior, has undertaken research to define the chemistry involving these metals. Arsenic in copper smelting is the first to be investigated. Roasting, the first step in many copper smelters, was chosen for initial investigation because of the potential for arsenic removal in this primary process. Simple, static-bed, vaporization experiments were devised to obtain the data in this study. Ancillary transpiration and mass spectrometry were also used to delineate conditions necessary for arsenic volatilization from a roaster feed. For nearly complete arsenic removal, a temperature of 650°-700° C, a reducing atmosphere including carbon monoxide, and a source of sulfur were found to be essential.

Jan 1, 1980

I am much pleased by your presentation of my article and flattered to the extent that the cover design refers to it. Incidentally, as between folks who like to work with words, refer to line 6, second full paragraph, page 773 (August Mining Engineering) Would "for" preceding technological have changed the percentages in lines two and three of the bold-face heading on page 770? The intent was coequality among three, (studies of mankind, of science, and of technological empirics). Thirty-three pct for "man" studies is a pretty big bite for engineering schoolmen; 50 pct they won't even examine, let alone nibble at. Arthur F. Taggart For those of you without a copy of the August issue handy, the sentence referred to read: The plea herein is to make the overall time allotment for studies of mankind coequal with those, for science and technological empirics.... Professor Taggart suggests that insertion of the word "for" would clarify the intent of coequality among three divisions of study: The plea herein is ... for studies of mankind coequal with those for science and (for) technological empirics. Editor.

Jan 1, 1952

By R. L. Tobie, E. K. Staley

Because of high production demands at San Manuel mine (approximately 40,000 tpd) and the relatively narrow grade range of the orebody, no attempt is made by the company to mine selectively. The caving sequence is laid out to meet the production demands, and proceeds in a manner to induce the least amount of weight on extraction openings. Once an area is undercut, draw control procedures are applied uniformly until the area has been mined to depletion. The orebody, located 50 miles northeast of Tucsoil, Ariz., is a low-grade deposit of chalcopyrite disseminated throughout a structurally weak, highly fractured, strongly altered granitic host rock over- lain by several hundred feet of relatively competent andesitic conglomerate. When undercut, the granite ore caves readily into fragments which usually pass through the grizzly without either excessive breaking or an undue amount of secondary blasting.

Jan 6, 1967

By Wenbing Guo, Gaobo Zhao, Erhu Bai, Brijes Mishra

"Violent damage to overlying strata can occur above the large mined-out space left by high-intensity longwall mining. For the safe mining under the aquifer and surface water body, it is imperative to investigate the criteria of overburden failure degree due to high-intensity mining. In this paper we present the characteristics of high-intensity longwall mining panels and overburden critical failure. Based on the geological and mining conditions of a high-intensity mining panel, 3D numerical models that consider the maximum horizontal principal stress and minimum horizontal stress and their orientations with the panel advance direction were established by using the 3DEC software. Sizes of the panel reaching the critical failure of the overburden under different mining thicknesses (3.5 m, 6.5 m, 9.5 m, 12.5 m, and 15.5 m) were analyzed. Further, criteria of overburden critical failure were proposed for the high-intensity mining. The coefficient of overburden critical failure (Cf) is the ratio of the strike length (Ls) to the mining depth (H). Through curve fitting analysis, a fitting equation between Cf and mining thickness was obtained. The results showed that overburden failure criterion with high-intensity mining panel is 0.38 = Cf = 0.97 with different thicknesses. Field measurements validated the results from the numerical models.INTRODUCTIONHigh-intensity longwall mining refers to a coal mining method with thick coal seam, large panel width, fast face advance rate, and severe damage to the overburden and surface in China (Guo et al., 2018). Violent movement of the roof rock and severe damage to overlying rock strata occur in the large mined-out space left by a high-intensity longwall mining panel, which is a 3D (three-dimensional) structure layout with highly non-uniform stress distribution. Recognition of such fact a will facilitate this overlying rock strata failure problem investigation (Peng et al., 2019).The studies of overlying strata failure due to longwall coal mining have been reported by some scholars with different methods. Kang et al. (2018) studied the sudden massive roof collapse during longwall coal retreat mining by a large-scale two-dimensional physical model and a UDEC numerical model. Ghabraie et al. (2015) researched the mining-related strata movement by applying the three-dimensional laser scanner, optical transducer, and digital image processing techniques to two-dimensional physical models. Wang et al. (2015) analyzed the structural characteristics and fracture failure process of overlying hard and thick main roof by a 3DEC numerical model; this study also investigated the geostress reduction and permeability enhancement redistribution of the adjacent coal measure strata by FLAC3D. Guo et al. (2012) performed a three-dimensional finite element analysis and shared some insights into the dynamic interaction between mining induced strata stress changes, failures, and gas flow patterns. Meng, Shi, and Li (2016) proposed a 3D coupling model between stress and permeability, investigating the dynamics of a stress, permeability coefficient using FLAC3D. Khanal, Guo, and Adhikary (2019) used the 3D numerical modelling approach (COSFOW) to investigate the strata deformation and the change in permeability in the overburden strata due to the underground extraction. However, few studies considered the influence of the horizontal stress on overburden failure in a high-intensity longwall mining panel, and the critical failure criteria of overlying rock strata is unclear."

Jan 1, 2019

By Tiejun Chun, Marcus Emrich, Jian Pan, Deqing Zhu, Vinicius Mendes

"Joint projects of studies of hematite acid pellet have been implemented to develop technological solutions for using Vale hematite pellet feed in Chinese palletizing plant. Beneficial improvements on the pellets quality were achieved by adjusting the blends composition and using new technology of pre-treating the blended pellet feed with HPGR (High Pressure Grinding Roller) on rotary kiln pellet technology. The drop strength of green balls increased from 3.4 to 6.0 times from 0.5m height, at the same time, the bentonite dosage decreased from 1.5wt% to 0.7wt%. The compressive strength of roasted pellets reaches 2500 N/pellet. The reduction swelling index of roasted pellets is below 15%.IntroductionWith the fast development of steel industry in China, the production of pellets has been further expanded. Pellets are used as a high quality charge for blast furnace and the annual output is around 80Mt pellets [1]. According to the developmental trend, sinter will be replaced by pellets due to the larger environmental impact of sintering plants when compared to pelletizing plants. For example, the specific CO2 emission in sintering process is around 2.5 times higher than in pelletizing process. However, the steel industry of China has been confronted with a serious shortage of domestic pellet feed due to the low iron grade of Run-of-Mine ore despite of huge reserves of iron ores [2]. Therefore, more pellet feed, mainly hematite, has been imported to make pellets."

Jan 1, 2011

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 12,564-acre portion of the 34,795-acre Rockhouse Wilderness Study Area (CA-010-029) in order to evaluate its identified mineral resources. The study area is located in Kern and Tulare Counties, CA, about 60 air mi northeast of Bakersfield at the south end of the Sierra Nevada. A review of the geologic and mining literature, and a field examination identified a turquoise and a gold prospect in the study area, and another gold prospect and a feldspar prospect within a mile of the study area boundary. Thirty-three rock and 16 alluvial samples were taken.

Jan 1, 1988

By J. D. Gillaspie, D. T. White

"Sulphuric acid atmospheric leaching of nickel saprolite / garnierite ores was proposed in the early twentieth century, prior to the development of the pressure acid leaching process for limonite ores. Sulphuric acid leaching with alkali addition for iron precipitation as jarosite has been considered periodically since the early 1970s, shortly after the development of the jarosite process for iron control in zinc refining. In the late 1990’s a series of flowsheets were proposed and tested involving simultaneous atmospheric leaching, iron precipitation and acid regeneration. These were considered particularly suited to sequential leaching of limonite and saprolite ores. A number of laterite sulphuric acid leaching processes utilising this chemistry have been put into commercial operation. Similar sequential leaching flow sheets involving precipitation of iron as goethite were also developed and piloted. This paper will firstly describe some of the important historical developments of both the jarosite and goethite processes. It will then provide descriptions of the commercialised processes involving alkali jarosite/alunite precipitation, with special emphasis on the downstream impurity removal requirements necessary for efficient recovery of nickel and cobalt from solution.INTRODUCTION This paper is a summary and extension of previous works with which the authors have been involved, on the subject of sulphuric acid leaching of nickel laterites (Adams, et al., 2004), (Liu H. , Gillaspie, Lewis, Neudorf, & Barnett, 2004), (White, Miller, & Napier, 2006), (White, 2009), (White & Gillaspie, 2013), (White & Gillaspie, 2015). Some of the historical developments of both the jarosite and goethite leaching-precipitation processes will be described, followed by a description of the commercialised sequential nickel laterite leaching processes, involving alkali jarosite/alunite precipitation and acid regeneration, with a comparison to the equivalent goethite based processes. These will include Jarosite Atmospheric Leaching (JAL), Goethite Atmospheric Leaching (GAL) and combined Pressure Acid Leaching – Atmospheric Leaching, termed EPAL®. There will also be an explanation of the downstream impurity removal requirements necessary for efficient recovery of nickel and cobalt from solution."

Jan 1, 2016