Search Documents

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"This report is () expansive test program by the Bureau of Mines to determine methods from various and ferrous manganese-grade product () widespread () and manfniferrous iron ores. Among the samples received for testing was one from the pits of the Barytes Mining Co., 1-1/ 2 miles northeast of Cartersville, Ga.. The property is approximately in the center of the Cartersville manganese district and shares a common corner with properties of the New Riverside Ochre Co. and the Etowah Development Co., both producers of manganifereus ores. The deposit is typical of the district and occurs in residual clays resulting from weathering of the Shady limestone and Weisner quartzite. 7/The property is developed by a number of open pits ranging to 60 feet in depth. In 1918 several carloads of manganiferous iron ore was mined from an alit on the property. Since then mining operations have been negligible. The ore is known locally as calico ore.A 4-ton sample representing -re as it occurs in the -pen pits vas furnished for testing. The sample consisted of a mixture of red iron oxides, wad, and clay, with small pebbles of manganese oxides and siliceous fragments scattered throughout."

Mar 1, 1943

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By Jorgen Elbrond

In a stream of ore in an underground mine or in a beneficiation plant bins are installed between machines or machine system. When the upstream machine is stopped the downstream machine can continue operation for a while and vice versa. The paper describes a procedure for calculating the total capacity of a system consisting of two machines with an intermediary bin as a function of the bin's live volume and of the installed machine capacities and their production variations, which are defined. Extensions to several machines in parallel and in series are shown as well as practical examples.

Jan 1, 1982

By T. L. Lee, D. Y. Tan, J. Mi

Considerable progress has been made in studying the mechanism and effectiveness of using ultrasound waves to manipulate alloy solidification microstructure, However, uncertainties remain in both the underlying physics of how microstructure evolve under ultrasonic waves, and the best technological approach to control the final microstructure and properties. We used the ultrafast synchrotron X-ray phase contrast imaging facility housed at the Advanced Photon Source, Argonne National Laboratory, USA to study in-situ the highly transient and dynamic interactions between the liquid metal and ultrasonic waves/bubbles. The dynamics of ultrasonic bubbles in liquid metal and their interactions with the solidifying phases were captured in-situ for the first time. The experiments were complemented by the simulations of the acoustic pressure field, the pulsing of the bubbles and the associated forces acting onto the solidifying phases, providing more quantitative understanding for using ultrasound to control the growth of dendritic grains and to enhance grain multiplication effects for grain refinement.

Jan 1, 2014

By George Bockosh

Mr. Bockosh is an electrical engineer with the U.S. Bureau of Mines In Pittsburgh, and has devoted the last two years to research on underground illumination. He formerly was a mine maintenance foreman and worked two years underground. He is a graduate of the University of Pittsburgh, where he is now working toward his masters degree in mining. When Congress first legislated light in American coal mines, it was a little like mandating a walk on the moon before the first satellite had been put in orbit. It was never a question, of course, of whether it could be done. But no one knew quite how. It's one thing to string a few light bulbs, and quite something else to provide uniform, sufficient, safe and reliable illumination, with fixtures that will hold up under some of the toughest conditions in the world - in the life-and-death circumstances of a craggy, black cavern filled with dangerous, moving machinery. In fact, in 1969 when Congress originally mandated illumination standards for the work places of underground coal mines, no one even knew just how much light was needed. That question was answered within a year by the National Bureau of Standards. In a study commissioned by the U.S. Bureau of Mines, the Bureau of Standards determined that underground mine should be illuminated with a light intensity of 0.06 foot-lamberts, a measurement of light reflected from surfaces in the lighted area-as opposed to foot-candles, a measurement of light from the source of illumination-in order for miners to adequately see what they are doing. That study was followed by more detailed research done at the Bureau of Mines' direction by the Research and Development Department of the Naval Ammunition Depot in Crane, Ind. This work evaluated the specific lighting needs of miners engaged In more than 100 different job tasks in all three types of coal mining- conventional, continuous and longwall. The Naval Depot report brought forth nearly 300 pages of detailed lighting data and concluded that proper illumination of mine work areas would serve more than just the cause of mine safety.

Jan 1, 1976

By S. Subhawong

Following the startup of the zinc plant in Clarksville, Tennessee, in 1978, the original effluent treatment plant did not perform as designed. The sludge, produced in a conventional lime neutralization treatment, settled poorly and began to fill the permitted lined impoundment within two years, well short of the original design capacity. Another sludge pond had to be constructed. This led to a new process modification of the original design. Although the design is still based on the conventional lime precipitation of heavy metals, the current effluent treatment plant has evolved into a hydrometallurgical circuit, capable of producing good quality water without generating sludge. Undesirable elements are bled from the zinc circuit and are rejected through the effluent treatment operations. Wallboard grade gypsum is produced, instead of sludge, and all the gypsum is sold to cement and wallboard plants. This operation also recovers and returns more than 1,500 tonnes of zinc annually to the 105,000 tonne/y zinc plant.

Jan 1, 2000

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05

Jan 1, 1910

By Thomas V. Falkie, R. Venkataramani

The empirical nature of this investigation required measurements of variables under operating conditions in underground coal mines. The variables to be measured were based on the postulated character¬istics of the loading function, as described in the previous chapter. One class of variables presumed to influence the loading function are geological variables. Accordingly, the sites for data collection were selected in different bituminous coal seams at dispersed locations in order that variation in geological conditions would exist. Seven mines in central and western Pennsylvania and one mine in northern West Virginia were selected as data collection sites. Five different coal seams were represented by these mines. The remaining classes of variables - geometric, mechanical, and procedural - were measured as they occurred in the mines. A description of the measurements, and the conversion of these measurements to forms which could be-analyzed for effect on the loading function is given. Mining Dimensions At the underground working face, the following dimensions were measured: a. Thickness of coal excavated. b. Thickness of shale excavated. c. Total height excavated. d. Width excavated. e. Depth of penetration of each machine cut. With the exception of the last of these dimensions, all were measured

Jan 1, 1972

By Joseph Kelly, Christopher Kelsey

This revolutionary super-fine crusher has the unique capacity to generate fine and ultra-fine products from single stage reductions of coarse or fine mineral feeds. The crusher consists of a rotating compression chamber and an internal gyrating mandrel. The axis of rotation of the shell is displaced relative to the axis of the vertically mounted mandrel. The inner surface of the compression chamber is machined as double cone frustums at an angle equal to the displacement angle. Crusher feed is accelerated into a compacted particle bed, which lines the inside of the compression chamber. The depth of the compacted bed progressively increases until the mandrel is engaged. The mandrel is then free to rotate with the compression chamber. Continued feeding increases power draw and triggers the counter rotating mandrel gyration drive. The gyrating mandrel delivers multiple compressions at high pressure to the rotating particle bed. High concentrations of energy are harnessed within a small active volume over short retention times. The combination of extraordinarily high power intensity and extreme compressive force results in primary compressive fracture and induced secondary tensile failure. The axially displaced rotation of the compression chamber effectively distributes the breakage forces throughout the particle bed. This paper covers open circuit, pilot trials on magnetite, perlite, garnet, marble and a copper/pyrite concentrate. Particular emphasis is placed on the extraordinary results achieved with trials on zircon and highly refractory fly ash. The extreme duties were deliberately chosen to demonstrate the crusher’s application scope and potential to impact capital operating and maintenance costs as the technology matures. Super-fine crushing, once considered impracticable has the potential to offer compelling options for the generation of ultra-fine products.

Jan 1, 2014

By A. W. Laughlin, C. R. Mansfield, M. J. Ferris, D. A. Cremers

Laser-Induced Breakdown Spectroscopy or LIBS can be used to provide exploration companies with precise and accurate chemical analyses in the field, in real-time, resulting in major time and cost savings. Using a Field-Portable Analyzer(FPA), anomalies can be followed up immediately while crews are still in the field. Lower limits of detection (LLDs) are element dependent, but many are sufficiently low to be useful in exploration. LLDs in ppm for selected elements of interest are: Be-2, Cu-3, Zn-20, As-200, Sb-500, Pb-30, Ag4,Mo-100, B-33, Ti-500, V-350, and Cr-l. LIBS analyses require little or no sample preparation.

Jan 1, 1999

By Ian Selby

Resource management is a key factor in the operation of a successful marine aggregates business; it is integral to the development of sustainability, satisfying increasing commercial, quality, and environmental performance standards. Resource management is based on the combination of; (i) a thorough evaluation and understanding of the resources on the sea bed and (ii) a dredging plan targeted to permit the effective and efficient extraction of the resources whilst mitigating impacts and leaving the sea bed ready for recolonisation.

Jan 1, 2004

By H. T. Shore, J. M. Schultz

A number of experimental rnethods—X-ray powder diffractometry, Laue photography, X-ray small-angle scattering, and transmission electron microscopy and dijfraction—have been utilized to examine the morphology associated with precipitation from the terminal, g, solid solution of a Zn-1 pct Cu alloy. A significant age hardening was observed in a 1 pct Cu alloy. X-ray and electron diffraction results showed that the structural inhomogeneities associated with the hardening were isotructural with the matrix. The average size and shape of the inhomogeneities were deduced from the electron microscopy and X-ray small-angle scattering. The preprecipitates are hexagonal platelets some 300? in diam. and some twelve unit cells thick. The orientation of the platelets was deduced from Laue photographs and electron diffraction. The platelet plane is (0001). When a large amount of pre-precipitation is present in a localized volume the new lattice is often disoriented by a rotation about (0001) of of the matrix. WhILE dilute Zn-Cu alloys have been commercially important for some 50 years, relatively very little is known metallographically about this material. The "Zilloys", zinc with about 1 wt pct Cu and sometimes a small addition of magnesium, are used to produce rolled zinc which is harder and stronger than that produced by other rollable zinc alloys.' According to the phase diagrams of the zinc-rich side of the Cu-Zn system, such dilute Zn-Cu alloys should age-harden;2-5 the solubility of copper in zinc, g-phase, at 424°C is 2.68 pct, while at 0°C it is only to 0.3 pct. However, the published literature on the aging of this system appears to be limited to a documentation of the contraction of 1, 2, and 3 pct Cu alloys aging at 95°c,6 and an attempt to measure changes in lattice parameters during aging.' In the latter work, no lattice parameter changes were detected, although a broadening of the highest-angle lines was detected and considerable diffuse scattering was observed. Micro-structural investigations have been limited to the latest stage of aging, wherein Widmanstatten precipitates are formed.3,47 These alloys are of interest for still another reason. The two most zinc-rich phases in the Cu-Zn system, 77 and E, are both hcp. Moreover, the change in a, between 17 and t for a 1 wt pct Cu alloy is onlv 3.64 -,~ct: the change in Co is 12.0 ict. It would be anticipated that precipitation in such a material might occur through metastable phases or G.P. zones with epitaxy along mutual 0001 planes. The goals of the present work are aimed at partially filling the void of knowledge concerning the early stages of precipitation from the g phase. In particular, we have attempted to document the magnitude of the age hardening of this system and to determine the size, shape, and orientation within the matrix of the elements of precipitation in an early stage of condensation. EXPERIMENTAL A) Specimen Preparation. Specimens were prepared In two somewhat different ways, one method being used for X-ray Laue and diffractometer measurements, optical microscopy, and Rockwell hardness measurements and the other used for electron microscopy and X-ray small-angle scattering. In the first case zinc and copper in the proper proportions to yield a 1 wt pct Cu alloy were melted together in a closed graphite crucible. Castings so made were free of apparent segregation or oxidation. The castings were then solution-annealed at 400°C for several days and then quenched in water to room temperature. Filings of portions of the specimens were made for use as X-ray powder diffractometry specimens. The electron microscope material was made as follows. Castings were made under vacuum with copper powder placed inside a hollow zinc cylinder to insure good contact of the materials. These 1 wt pct Cu pieces were then rolled to 0.1 mm with an intermediate anneal in vacuo. The rolled sheets so formed were then annealed for about 6 hr at 225°C. Finally the specimens were electropolished slowly until thin enough for transmission electron microscopy. The polishing is discussed in greater detail in the Results section. B) Measurements. X-ray measurements of three types were performed. A G.E. XRD-5 diffractometer was used to examine powders of the alloy for identification of second-phase material. A Kratky small-angle camera, also operating from a G.E. tube, was used to investigate the sizes of small precipitate particles. In both cases, nickel-filtered copper radiation was utilized. Finally, individual grains of the large-grained castings were examined in the back-reflection Laue geometry. Electron microscope studies were carried out with a J.E.O.L. Model 6A instrument. RESULTS A) Hardness Measurements. Hardness measurements performed at room temperature on the large-grained polycrystalline specimens showed a hardening which was essentially complete in 3 hr. Fig. 1 shows a typical plot of hardness vs aging time. The relative magnitude of the ultimate hardening varied from run to run between 150 and 200 pct of the value for the material immediately after quenching from the solution anneal. Most probably the variations reflect small changes in the time taken to remove the specimen from the vacuum furnace after the solution anneal.

Jan 1, 1969

By Thatcher R

In areas where undeveloped land represents a scarce resource, an upgraded post mining land use can result in economic benefits to both the mining company and to the community. A study undertaken at Allied Queensland Coalfields Ltd's Aberdare Colliery located between Brisbane and Ipswich during 1986/1987, assessed the costs and benefits of developing the site following mining for grazing, forestry and residential uses. The proposed final land use plan comprised a combination of these uses which can be upgraded to higher valued uses once subsidence monitoring of backfilled opencut areas and dumps indicates that total settlement has reached acceptable levels. The study involved the documentation of existing site environmental parameters and the delineation of site opportunities and constraints. The unpredictable nature of settlement over backfilled opencuts and overburden dumps represents the major constraint to urban development on mined areas.

Jan 1, 1987

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By James R. Herring

An unusual combination of ten new, deep (-100 m) coreholes and an extensive high-resolution seismic reflection network enables us to produce a detailed study of the phosphorite resources in the Tertiary strata of the Georgia continental shelf. These strata are mixtures of a terrigenous facies, notably quartz and clay along with minor amounts of other aluminosilicate minerals, and of a marine facies, notably phosphorite and carbonate. Phosphatic sediments occur throughout the cores, however the richest phosphorite beds are in the middle Miocene (Serravallian) sediment, where they constitute up to 70 percent of the sediment mass. Major zones of phosphate enrichment occur chiefly at major unconformity boundaries (tops of Oligocene, lower and middle Miocene, upper Miocene, and lower and upper Pliocene) and at prominent intrastratal reflectors representing minor unconformities within units. Phosphorite co-occurs with the clay minerals, especially palygorskite, but correlates inversely with carbonate and detrital quartz, indicating a low-energy depositional environment. The clay minerals present in these strata, which have an environmental consequence on recovery of the phosphorite, are varying concentrations of smectite, kaolinite, mica, palygorskite, and sepiolite. Phosphatic resources have been determined within only the Miocene strata. Sediment volume for this unit to the 100 m isobath on the continental shelf has been established using the high-resolution seismic reflection network that has been calibrated using the deep coreholes. Phosphorite grains larger than 0.1 mm average about 40% of the sediment. In turn, most of the remainder of the sediment in this size range is quartz, which is separable from phosphate grains using conventional flotation techniques. Our estimate is that 300 Gt of phosphorite lie within the Miocene strata of the Georgia continental shelf.

Jan 1, 1994

By H. T. Kennedy, S. G. Dardaganian, J. L. Clanton

This paper presents equilibrium ratios measured on oil and gas samples taken from the Kelly-Snyder field at the reservoir temperature of 128°F. From these data smoothed curves were constructed for the reservoir fluid up to the bubble-point, 1,874 psia. A material balance calculation, based on the use of equilibrium ratios instead of the usual solubility and shrinkage meayr~rements is made on the field and compared to the con\.entional method. DETERMINATION OF EQUILIBRIUM RATIOS The equilibrium ratios, or K values were obtained by recombining separator samples of oil and gas taken when the reservoir was above its bubble point, and thus represented the reservoir fluid before any change had occurred due to the evolution of gas. The well sampled had a gas-oil ratio of 617 cu ft of high pressure sepalator gas per barrel of separator oil. and a bottom-hole temperature of 128°F. Samples were brought to equilibrium by agitating for 24 hours in a thermostat, maintained at the proper temperature within 0.2ºF, mercury being added when necessary to maintain the pressure constant. Samples of oil and gas were then taken by constant pressure displacement, and analyzed by low temperature frac-tionation. Equilibrium ratios were determined at 128°F and 500, 800, 1,000 and 1,400 psig. At the latter pressure, there were indications that the gas samples were contaminated with small quantities of oil, and only data taken at the first three pressures were included in Fig. I. This figure has been extended to higher and lower pressures by the use of the Fluor charts for 3,000 psi convergence pressure, on which the experimental points fit well. MATERIAL BALANCE EQUATIONS The possible errors involved in conventional material balance equations have been analyzed by Muskat1. Where the errors occur in field measurements, or in obtaining effective averages from variables such as gas-oil ratio and pressure, they will evidently be involved in any attempt to estimate the content of the reservoir. On the other hand, substantial errors may be introduced in conventional material balance calculations by: (1) the neglect of the amount of oil dissolved in gas at high pressures and temperatures in the reservoir, but which condenses under separator conditions; (2) the assumption that the separation of oil and gas in the reservoir may be duplicated by a differential liberation in the

By M. G. Irish, E. E. Vidal, M. J. Jahraus, P. R. Taylor

An experimental system has been designed to monitor on-line variations of leaching parameters in a closed circuit of cyanide leaching solutions and gold bearing ores. Experiments performed to deter-mine variations in some important leaching parameters of the solution: pH, dissolved oxygen, free cyanide, oxidation/reduction potential, gold content, temperature, pressure and solution chemistry. By comparing results obtained when the leaching solution is allowed to become acid or kept basic, it was possible to infer the chemical reactions that occurred between the solution and the ores.

Jan 1, 2004

By S. K. Tarby, W. O. Philbrook

Limited experimental data and a critical review of the literature are given to indicate that the true equilibrium distribution of manganese between carbon-saturated iron and blast-furnace type slags has not yet been satisfactorily established as a function of the composition, temperature, and pressure of the system. THE distribution of manganese between carbon-saturated iron and blast-furnace type slags has been studied by a number of investigators.1-7 Generalization of the results of these works indicates that the weight percent distribution ratio, (%Mno)/[%Mn], decreases with increasing temperature and slag basicity, in accord with thermodynamic data and practical observation. However, where comparisons among these studies can be made for similar slag compositions and temperatures, the reported values of the manganese distribution ratio are discordant. The variations are attributed to failure of the experimenters to bring their systems completely to equilibrium with graphite and CO at 1 atm, as judged by departures from silicon equilibrium. Even in the most recent work,5-7 this problem was recognized but the authors made the questionable assumption that equilibrium could prevail for manganese distribution even though other reactions were still in progress. Manganese equilibrium values for three particular slag compositions were required incidental to a kinetic study8 and were determined experimentally. Special pains were taken to approach concurrent equilibrium with respect to silicon. Although the results were not completely definitive, they indicate that the true manganese equilibrium distribution ratios are lower than have heretofore been reported. The data are presented together with a brief commentary on the literature to suggest the need for further work in this area. EXPERIMENTAL METHOD Equilibrium runs were carried out in a stationary, induction-heated graphite crucible closed by a graphite lid and flushed continuously by a slow flow of carbon monoxide at 1 atm pressure. Temperature was controlled manually within ±3 deg C with the aid of immersed thermocouples in mullite tubes protected against slag attack by graphite sleeves. The desired temperature was established by a calibrated Pt vs Pt-10 pct Rh thermocouple and control was then maintained using a more stable W-Mo couple. Runs were made at 1500º and 1575ºC for durations of 7.5 to 10.5 hr. The charges were calculated to yield 400 g of metal and 100 g of slag. The primary slag compositions and designation numbers were as follows:

Jan 1, 1963

By Waldemar Lindgren

Introduction To the miner, as well as to the geologist, the eastern part of Cuba is a most interesting region. Here we find, in contrast to the moderate relief predominating elsewhere in the island, an imposing mountain range, the Sierra Maestra, extending east and west parallel to the coast, its precipitous front facing the blue Caribbean Sea.. In a geological sense this range is largely an unknown land, the only well-explored region being that in the vicinity of Santiago. The range also contains the most important mineral deposits of the island. They comprise, first, a series of iron deposits yielding a partly hematitized magnetite with low content of phosphorus; second, a remarkable copper-bearing vein at El Cobre; and third, various manganese deposits. Probably more deposits will be found, for the larger and western part of the range is as yet little explored and its slopes are covered by a thick tropical jungle. The following notes are based on a short visit by the senior author in January and February of 1914 to the mines at Daiquiri, El Cobre, and Mayari. For many courtesies and great assistance he is deeply obliged to Charles F. Rand, President of the Spanish-American Iron Co.; to George W. Pfeiffer, General Manager, and to the several members of his staff.

Jan 10, 1915

By Christoph Mueller

Mining operations are characterized by cost pressure and cycling product prices. A high potential for enhancing efficiency is the integration of all single steps of the mining working chain into a production process structure to make advantage of an optimized flow of material and information through the ?moving ore factory?. As modern mining machinery today is controlled electronically and even already operated autonomously, a smooth and cost efficient flow of data in the mining process will be crucial for cost efficient future mine operations. Therefor, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ?common electronic language? for easy and standardized data exchange between mining machines and central computer systems. As in other industries, this standard is expected to have significant impact on the use of automated equipment. It shall provide easy ways of using multi vendor machine installations in data controlled mining processes. At the same time it reduces cost for individual development of interfaces for all parties involved. Standardized data exchange is also a crucial precondition to integrate the mining process into enterprise level modeling, cost analysis and decision finding systems. The standard?s technical architecture is open and flexible for future applications. It uses modern XML technology enabling easy data exchange with commercial databases as well as open on line networking. The IREDES work is carried out by the initiative members working jointly together in the technical work groups. Prototyping implementations of the Drill rigs profile are currently going on. Further profiles under development cover LHD?s/Loaders/Trucks and Explosives Chargers. The first official release covering the Drill Rigs profile is planned for the end of 2002.

May 1, 2002