Search Documents

By T. J. Woodside

A. E. LEE*—One question of the flue leading to the tube coolers. What gas velocity is maintained to prevent settling of the finely divided fume ? T. J. WOODSIDE (author's reply)— 30 fps. Of course some fume settles out, but is immediately carried away by the screw conveyors. H. R. BIANCO —How effective are the soot blowers ? Do you have to use any hand lancing? T. J. WOODSIDE Only one point, which is right at the top of the economizer and which the soot blowers do not reach, we occasionally hand lance. But everywhere else the soot blowers have been very effective and no hand lancing has been done. L. V. DAVIDSON*—Do you have considerable variation in the lead content of the fume collected if the lead is higher, and is there greater tendency for the fume to stick on the boiler tubes ? T. J. WOODSIDE—There is very little variation in the lead content. From 5 to 7 pct is the widest range variation we have had and we have noticed no difference in the behavior of the fume. C. R. KUZELL—Mr. Woodside has been quite generous with data pertaining to metal and fuel economics. I think he stated that the coal consumption of the furnace was 21/10 21/10 for a pound of zinc recovered. I take it that that is the gross coal input to the furnace. I wonder what the net fuel consumption in terms of coal might be after crediting the fuel equivalent of the waste heat steam recovered? T. J. WOODSIDE—The fuel value of the waste heat steam is approximately 42 pct of the heat input to the furnace. A very large part of the heat, of course, goes out in jacket water—44 pct. A. D. TERRELL*—I would like to know how much lead is in the deleaded material. T. J. WOODSIDE—It is a little less than 2 pct now.

Jan 1, 1950

By Alex Chapman, Cam Thomas, Bryan Karney

"During the early summer of 1989, Ontario Hydro removed a concrete portion of the North Channel Dam at Crystal Falls Generating Station by blasting and excavating in marine conditions. Because of the severity of underwater blasting and because the site was in close proximity to the replacement dam, there was concern that hydraulic shock waves generated by the detonation could damage either the new dam or its control structures. This paper examines the data associated with the hydraulic shock waves generated by underwater blasting, and studies the effectiveness of an air curtain in reducing the peak pressures. In previous trials using the air curtain technique, a rule-of-thumb factor was used to estimate that only 10% of the original pressure pulse would propagate across the air curtain. However, this value had little basis in theory. A theoretical formulation of the problem by Karney in 1989 indicated a provisional value of 0.18 for this factor, but was heavily dependent on confirmation from in-field testing. Data provided by Ontario Hydro from an actual blasting procedure indicate that a more conservative value of 0.32 may be more appropriate. Thus.although the air curtain did provide considerable reduction of peak pressures, the data at Crystal Falls indicates its performance was below the anticipated level. However, due to problems with the instrumentation and some inconsistencies in the resulting data. it is recommended that this value be further refined as additional data become available."

Jan 1, 1992

By John McDonald

THE amount of published literature in the field of mechanical proper-ties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherch1 have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing' with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in, properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the proper-ties of alloys in conditions where the effect of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these proper-ties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments will produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of working and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treat-ments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloys have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are relatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1939

By D. E. Walsh, J. T. Hollow, H. K. Lin, J. L. Oleson

At the Fort Knox Mine, Fairbanks, Alaska, carbon fines are generated during stripping, acid washing and kiln regeneration operations. Because of their gold value, carbon fines are collected by a filter press. Samples of the carbon fines show that they consist of 20% to 30% carbon, 70% to 80% grit and 0.17 to 0.68 g/kg (5.0-19.9 oz/st) gold. About 80% of the gold values in the carbon fines used in this study are in the form of recrystallized free gold grains, with the balance being the adsorbed gold on the carbon. High recoveries of gold and carbon were obtained from the fines in laboratory tests using froth flotation, with a high rejection of the grit. More than 95% of gold and 90% of carbon can be recovered by three stages of gold flotation followed by two stages of carbon flotation. Key words: Gold recovery, Activated carbon, Flotation

Jan 1, 2003

In ilmenite smelting, the FeO content of the feed material (nominally FeO.TiO2) is decreased by reduction with carbon. In a parallel reaction, a significant amount of the TiO2 is reduced toTi2O3. One of the striking features of these reactions is a consistent relationship between the extents of FeO and TiO2 reduction; this relationship is independent of furnace size. It was recently proposed that this relationship follows from the solidification behaviour of the slag, where the final slag composition corresponds to the minimum melting point (?eutectic groove?) in the FeO-TiO2-Ti2O3 phase system; the hypothesis is that solidification equilibrium with the freeze lining stabilizes the slag composition. If this is the case, the system of slag and freeze lining must be capable of correcting two types of disturbances: thermal and compositional. Thermal disturbances result from incorrect power input, for the feed rates of ilmenite and reductant. For example, excessive power input will tend to overheat the slag, causing the freeze lining to melt partially, establishing a new steady-state heat loss from the furnace. Compositional disturbances result from an incorrect reductant input for the given power and ilmenite input. In this work, the dynamic response of the slag and freeze lining to different inputs (flow rates of ilmenite and reductant, and power input) is modelled. The model is based on solidification equilibria, and quantified heat loss through the freeze lining. The conclusion is that the solidification equilibrium cannot constrain the composition to the eutectic groove for typical operating conditions. Keywords: ilmenite smelting, freeze lining, solidification, high-titanium slag

Jan 1, 2004

By W. E. Remmers

The fact that gray iron increases in volume, cracks and distorts upon repeated heating and cooling is rather conlmon knowledge. In ingot molds, Diesel engine pistons, carburizing boxes, continuous furnace parts, grate bars, stoker parts, and all castings that are subjected repeatedly to high and low temperatures, the phenomenon of growth presents a vital problem. Ingot molds distort and produce cracks which result in seams or laps and later appear as defects in the finished product. The heads of Diesel pistons frequently fail by cracking in a stellar shape. This is attributed usually to the result of permanent growth. Distortion and change of dimension of furnace parts frequently renders them entirely unusable. In chain grate stokers, mechanical difficulties frequently are caused by the growth of the links. In proper operation these links should never attain a temperature sufficiently high to start growth; nevertheless, some have grown in. on an 8-in. length when improperly operated. Even though the phenomenon is generally known there still exists a deficiency in the explanation of the mechanism of this growth. The field of investigators of this subject has a decided variation in opinion concerning the causes. The problem is of sufficient importance therefore to warrant further consideration. Review of Published Work Since the published work, particularly the European, contains much detail, only the outstanding results and conclusions of the investigators will be reviewed. The pioneering investigations of Outerbridge in 1904 and 1905 brought forth the conclusion that growth was not a function of chemical or crystallographic changes but was a result of the formation of fine hair cracks. These cracks are supposedly due to a nonuniformity of thermal expansion and contraction which ruptures the structure of the material. More recently Benedicks and Lofquist presented a purely mechanical theory, which is similar to that of Outerbridge. These investigators believe the temperature gradient from the outside to the center of the cast piece causes a contraction of the outer layers on passing

Jan 1, 1931

By S. K. Kawatra, T. C. Eisele

Pyrite depression is of great interest in sulfide mineral flotation, where pyrite is a common gangue mineral. Since the floatability of pyrite is a function of the pH and a variety of other chemical factors, pH control is a critical part of sulfide flotation circuits. A wide variety of pyrite-depressing chemicals have been studied and used in sulfide- mineral processing, with considerable success. However, there are certain applications where there are still no satisfactory pyrite depressants, and even when suitable depressants are available, there is always a need for less-expensive reagents. Microorganisms, such as the bacteria Thiobacillus ferrooxidans, are known to depress pyrite flotation. However, the dependence of the depression on the type of organism or on suspension pH is still being determined. In this study, the relative effectiveness of various microorganisms, and the effect of pH, has been examined. Screening tests using microflotation showed that every microorganism tested was capable of depressing naturally hydrophobic pyrite at acidic pH. Larger-scale experiments with two of the screened organisms and two different pyrites showed that microorganisms are very effective depressants at acid pH, but are largely ineffective at neutral and alkaline pH where the pyrite surface is not naturally hydrophobic.

Jan 1, 1994

Developments in the technology of explosive production and deliveryallow a greater amount of flexibility in rock fragmentation by blasting. The rock fragmentation efficiency of an explosive is currently given by a rating which is determined by the explosive manufacturers using proprietary formulae and methodology. Hence, comparison of explosives from different manufacturers may be misleading. Modeling of explosive energy, using a thermochemical code such as CHEETAH provides an objective standard by which the likely performance of different explosive formulations can be determined. Such modeling can be used for optimisation of explosive composition to match specific rockfragmentation objectives.

Jan 1, 2001

By B. P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using carbonate solutions. The objective of the present study was to increase the absorption rate of CO2 into the carbonate solution without reducing the absorption capacity of the solution. This approach used a polypropylene glycol methyl ether (PPGME) as a surfactant to chemically alter the gas bubble size. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations of 0, 0.12, 0.24, 0.36 and 0.48 g/L. Results showed that as the concentration of surfactant increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 mmol/min CO2 at 0 g/L PPGME to 3.92 mmol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in absorption capacity of the solution.

By W. G. Davenport

Methods of extracting copper are evaluated in terms of innovations during the 1970's, and predictions to the end of this century are made. It is concluded that between one and two new smelters and refineries will be needed per year until the turn of the century, and that most of these smelters will be of the oxygen or oxygen-enriched flash furnace type. For converting, the Peirce-Smith converter will still predominate, but the Hoboken converter will play an increasingly important role. Five Japanese pollution control systems are described and it is suggested that much of this technology will be included in future smelting installations. Further growth of hydrometallurgy is predicted, especially for oxide ores, based on improved product metal quality and low plant cost. A n increased level of scrap resmelting is also expected.

Jan 1, 1980

Portland cement is a finely ground mineral powder obtained by intergrinding a mixture of 95 parts of clinker and five parts of gypsum. It is the generic name for hydraulic cement a man made product which hardens in the presence of water. Today's cement started formally with a patent granted in 1824 to Joseph Aspdin, a Leeds bricklayer. He called his patented cement 'Portland' because it resembled a gray brown stone quarried on the Isle of Portland off the coast of England. The first cement to be made in the southern hemisphere is accredited to Nathaniel Wilson, a pioneer farmer who with his brother John began experimenting in 1874 with the limestone on their property near Warkworth. In 1884 they produced the first Portland Cement to be made in this part of the world.

Jan 1, 1978

By R. R. Odle

A laboratory and pilot-scale investigation of direct smelting of copper concentrates was conducted to determine the effect of concentrate analysis and the degree of roasting on the yield and quality of copper produced in a subsequent smelting step. A stoichiometric :mOdel of direct smelting is presented which predicts the? quantity of copper; slag, and white metal' prOduced'and the distribution of copper in these phases as a function? of the concentrate '(calcine) analysis.

Jan 1, 1983

By E. H. Jr. Crabtree

THE productive area of asphalt-bearing sandstone in Missouri is near the Missouri-Kansas state line near Nevada, the county seat of Vernon County about 100 miles south of Kansas City. While produc-tion thus far has been confined to Vernon and Barton counties, there are known deposits in adjacent counties. The area is served by four rail-roads: the Missouri Pacific, the Kansas City Southern, the Missouri-Kansas & Texas, and the St. Louis & San Francisco. The plant of the Reliance Rock Asphalt Corporation is in Vernon County, about 5 miles west of Nevada, at Ellis, a flag station on the Missouri, Kansas & Texas Railroad. A siding has been built to the plant so that the finished product can be loaded directly into railroad cars. The property consists of a lease of 240 acres in one block. All portions of the property not required for quarrying or processing the asphalt-bearing sandstone are used for farming by the fee owner. The entire tract is very flat so that there are no transportation difficulties from quarry to plant.

Jan 1, 1935

By P. H. Oliver

"The current theory of how explosives fracture rock offers no explanation for the improvements in fragmentation and the reduction of fly rock and back break which occurs when an adequate inter-row delay time is used. Nor does it explain why fragmentation improves with rectangular drill patterns where the hole spacing may be as much as four times the hole burden.A new theory of rock fragmentation is proposed which builds on the existing theory. It offers rational explanations for the many blast effects which the current theory does not address and the need for adequate timing delays between rows. It improves on the design of inter-row delay timing by defining the length of free-blasted face needed in front of a hole *Retired from Inco Ltd., Sudbury, Ontario when selecting the delay element which will provide an adequate inter-row delay time."

Jan 1, 2003

By F. W. Gray

A GEOLOGICAL study seeking to determine, for economic purposes, the value of the Sydney coalfield as a source of coal supply. Limitations of the coalfield come under two main heads: (a) Areal extent of the undersea coalfield. (b) The distance from shore at which coal can be mined at a cost of production permitting its profitable sale. Conclusions reached are that the areal extent of seams below the Phalen seam is of. small economic importance, and that non-persistence of these seams in full thickness and quality in the undersea extension of the coalfield will put an end to profitable mining before any limitations connected with distance from the shore-line become operative. With respect to the Phalen seam, non-persistence or deterioration of the seam will become effective in the western part of the coalfield, and less certainly in the eastern part of the coalfield, before operation of limitations by distance from shore. In the central portion of the coalfield, the seam probably persists in commercially workable thickness and quality to beyond the limit of mining set by distance from the shore-line. With respect to the seams above the Phalen seam between the Mountain fault on the extreme western boundary of the coalfield and the assumed termination of the deposition area on the eastern extremity of the field near South Head of Morien, there appear to be only such limitations as arise from engineering approach, distance from shore, sufficiency of strata cover between the sea-floor and the upper coal seams, and quality of the coal (with certain reservations as to the continuity of the upper seams under Sydney harbour and in the Sydney Mines-Little Bras d'Or district). Some of these seams have fragmentary land outcroppings from which their persistence seaward is assumed, and there may be other and still higher seams in the strata column which are entirely submarine.

Jan 1, 1941

By Nielen van der Merwe

The data base of failed pillar cases as used by Salamon and Munro (1967) in their original analysis to determine the strength of coal pillars empirically, has been updated for this study. It is shown that the Vaal Basin and Klip River coal fields exhibit similar behaviour, i.e. failure at high safety factors within a short period of time after their creation. Those collapse cases have been omitted from the new data base. New failures that occurred after 1967 have been added, except for those that occurred in the Vaal Basin and Klip River coal fields. (1967) a technique to minimise the area of overlap between the populations of failed and intact pillar cases, the new data base was re-analysed in conjunction with the original Salamon and Munro (1967) data base of intact pillar cases. It was found that a linear formula reduced the overlap area by 22%. The new formula predicts higher strength for pillars with a width-to-height ratio greater than approximately 2S and a lower strength for smaller pillars. For most current South African coal mining conditions, using the new formula for pillar strength will result in leaving smaller pillars without sacrificing stability. The reason for this is that the Salamon and Munro (1967) formula underestimated the strength of larger pillars and overestimated the strength of smaller pillars. The potential benefit for the South African coal mining industry amounts to saving reserves equal to the total production of two large mines per year.

Jan 1, 2002

By Cyril Stanley Smith

BETA brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, but at low temperatures [ ] an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 490°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An [ ] excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shockley.1 All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching. With most ordered alloys, cold-working induces disorder and

Jan 1, 1942

By Persifor Frazer

The accompanying diagrams represent a lamp provided with certain improvements which render it more serviceable for the use of the engineer or other mining official who is often compelled to visit several mines a day remote from each other, and may be called on to use the magnetic needle in any or all of them. These requirements demand that the material of which it is made should be copper, and that it should be capable of being closed oiltight, for emptying and refilling the lamp at each mine would be a less expeditious as well as a less cleanly process, and transporting a lamp of the ordinary kind over rough roads on horseback or in wagon, would result in spilling the greater part of its contents. The general form of the lamp, including the false back to keep

Jan 1, 1882

By K. T. Koone, R. J. Blackwell

One of the more important problems to be solved in designing a miscible flood is related to the size of the solvent bank used. Size of the bank may be critical to economic success. Too large a bank loses money; too small a bank may deteriorate and fail to maintain the miscibility needed for high recovery. An important factor in deterioration of a small bank is permeability channeling. In a highly stratified reservoir, solvent speeds ahead in the more permeable zones and mixes laterally with fluids bypassed in adjacent, low-permeability strata. Numerical solutions have been obtained .for the differential equations that describe the movement of a slug through a two-layer system in which mixing occurs both in the direction of flow and transversely. The solvent slug is assumed to have the same density and viscosity as the resident fluid and the pushing fluid. These solutions have been verified by comparing them with similar concentration profiles obtained in the laboratory in a 36-ft stratified model packed with glass beads. The theoretical study revealed that when the dominant mechanism causing a bank to fail is lateral mixing the bank size needed for a given recovery may increase with length rather than decreasing as the square root of reservoir length, as suggested by one-dimensional mixing theory. From a comprehensive examination of the variables, a generalized correlation is developed that relates strata thicknesses, bank size, fluid velocity, mixing coefficients, system length and simple solvent-resident fluid phase behavior to the area miscibly swept. INTRODUCTION Miscible displacement, or solvent flooding, continues to receive widespread attention as a method for increasing oil recovery over that possible in conventional gas-drive or waterdrive projects. A basic economic requirement in the application of such processes is the use of as little solvent as possible. A basic physical requirement is that enough solvent be used to maintain miscibility. Economics places an upper limit on the size of a solvent slug, and physical considerations establish a lower limit. Consequently, the practicality of any given miscible process requires that the economic limit be greater than the lower limit imposed by physical requirements. Procedures exist for determining the economic limit; however, procedures for determining realistic minimum bank sizes exist for only special reservoir situations. In the past, bank size has usually been selected on the assumption of a piston-like displacement for which only longitudinal mixing is important. This assumption leads to the favorable conclusion that bank size, expressed as per cent of pore volume, is inversely proportional to the square root of length. Collins considered the problem of transverse mixing of solvent with fluids in bypassed zones with the assumptions that no forward mixing occurs and that the concentration is uniform in the permeable stratum of interest. 1 Lauwerier considered a mathematically similar problem in thermal recovery operations.2 Their work suggests the much less favorable conclusion that bank size could be directly proportional to the length or even higher powers of the length. This paper considers the physical behavior of a small solvent bank as it moves through a real reservoir, without imposing many of the restrictive assumptions of past treatments. To facilitate mathematical description, an idealized, two-layer model that permits mixing both laterally and in the direction of flow will be considered. A calculation procedure for solving the descriptive equations will be developed for a displacement involving fluids of equal density and viscosity. In addition, laboratory experiments designed to check the computational results will be described, and the coincidence of calculated and observed results will be discussed. The use of many solutions for a variety of bank sizes, strata thicknesses and characteristic system lengths to develop a usable correlation between

Jan 1, 1966

By D. W. Fuerstenau

The United States is rapidly approaching an acute shortage of minerals. According to some observers, this situation may even be more severe than the energy crisis because the US consumes nearly 30% of the world's mineral production. With the mounting competition for world mineral supplies, we can no longer take for granted that foreign mineral products will be available to the US as abundantly as in the past. In 1973, US consumption of mineral raw materials was $35 billion. Of this, $7 billion consisted of imports. Without a drastic reorientation towards the mining of domestic mineral resources, the 1973 $7 billion deficit might mushroom to $100 billion by the year 2000. Thus, a return to domestic sources of raw materials will become absolutely necessary-and will be bucking the trend of the past 25 years, characterized by capital investment for growth in multinational overseas mining operations.

Jan 11, 1975