Search Documents

By H. K. Livingston

A TECHNIQUE has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated. These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow.

Jan 1, 1942

By William P. Stroud

Chemical alteration of the compressive strength of sandstone has been investigated by the U.S. Bureau of Mines (USBM). Successful development of this technology would offer an attractive alternative to the methods now used for stress control in mines. Sandstone cores were stressed to failure under uniaxial compression at two different strain rates. Specimens saturated with either distilled or tap water showed an average 14% reduction in stress at failure compared with those dried in vacuum. Samples saturated with dilute solutions of aluminum chloride, hydrochloric acid, and polyethylene oxide showed no statistically significant difference in failure stress compared with those saturated with water. By contrast, compressive strength of the cores was increased some 7% by saturation with the nonpolar solvent carbon tetrachloride. No correlation was found between zeta potential and compressive strength.

Jan 1, 2010

By Henry Brehaut

The International Network for Acid Prevention (INAP) was formed in 1998 by 17 international mining companies to promote significant improvements in the management of sulphidic mine materials and the reduction of liability associated with acid drainage through knowledge sharing and research and development of technology. Since its inception two panels have been formed to identify and move forward with research projects and eight networks have been constituted to initiate interaction and knowledge sharing within the membership in specific areas of technical interest. An INAP web site has been developed to facilitate the sharing of information and to encourage the exchange and development of new ideas.

Jan 1, 2000

By William D. Mayercheck

The introduction of continuous mining machines in the late 1940's prompted the mining industry to reassess shuttle car batch-type haulage. Between place changes, the continuous miner could cut and load coal on a nearly continuous basis, but after loading a shuttle car, the high-capacity machine had to wait until the second shuttle car came inby and spotted itself under the miner tail boom. Thus, the wait-for-shuttle-car delay periods became the new bottleneck for increased coal production from the mine section. Recent studies have shown that nearly 25 pct of the continuous miner cycle time is consumed by delays in the haulage system, usually waiting for shuttle cars. Computer simulations of a face operation indicate that up to a 45 pct increase in coal production may be realized through the use of a continuous haulage system, assuming of course that the outby haulage system can handle this increased capacity. Coincidently, there are recent claims by some mines using continuous face haulage of a production increase of 45 pct compared with shuttle car haulage. These documented production records, computer simulations, and common sense indicate the potential of continuous face haulage in underground coal. The late 1960's and early 1970's saw several mining machinery manufacturers market mobile bridge carrier and piggyback bridge conveyor continuous haulage systems for use in underground coal mines. These systems have shown limited potential in some mines and outstanding success in others. It appears that no one system can be universally applicable to all underground mining conditions; thus, the Bureau of Mines has conducted extensive research over the last few years to investigate different types of continuous haulage systems for use in high and low coal seams that will advance the state of the art.

Jan 1, 1977

By H. W. Read

Sustained growth in demand for platinum group metals has resulted in an unfettered increase in new projects undertaken by the platinum producers. These projects are outsourced to various degrees. The argument of this paper is that both the client?s project manager and the consultant?s project manager are essential elements in the successful execution of a project. Their roles are not only different but also complementary, and are defined in the paper. Data gained from considerable experience in the South African corporate mining environment underpins the opinions expressed in the paper. Furthermore, an extensive literary search was undertaken to determine trends in related industries outside the South African context. Throughout the argument it is emphasized that project philosophy emanates from a systems view and must be treated as an overarching whole. The elements of project management become meaningless unless they are connected to one another and integrated into a cohesive unit. Advancing the knowledge field of project management is of critical importance to mining investors. There is no doubt that a key determinant of the sustainability of mining business is closely related to the efficiency of all-inclusive project management. From pre-investment and feasibility studies, implementation and execution, to ramping-up to full production, scientific project management has a critical role to play. Guidelines for the pursuance of this ideal are proposed. The introduction contextualizes the subject matter in an overview of the evolution of mine management in South Africa and abroad. Then, brief insight is given into the philosophy of project management. This exposition is confined to the predispositions, presuppositions and defining characteristics of project management. The core of the paper looks at the roles of the client?s project manager in relation to the consultant?s project manager. This section is underpinned by practical experience gained by the author on numerous mining projects. A view is taken of the future of project management in the mining industry. The conclusion summarizes the argument and aligns project management trends in the mining industry.

Jan 1, 2004

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderúrgica Belgo Mineira, João Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

By K. K. Kelley

"INTRODUCTION The Bureau of Mines nitrogen peroxide process (2) 3/ for extracting manganese from low-grade ores is essentially a two-stage process involving the reversible reactionMnO2 + 2NO2 + 6H2O = Mn (NO3)2 . 6H2O (1).At lower temperatures this reaction proceeds to the rigth and affords a means of dissolving manganece and separating it from unreacted ore. At higher temperatures the reaction proceeds to the left and manganese dioxide is recovered and nitrogen peroxide regenerated for recycling. Evidently, therefore, the energy required for decomposition of manganous nitrate is a matter of practical importance. Similar information for certain other nitrates also is desirable beceuse the nitration step of the process produces appreciable amounts of nitrates of other metals, such as iron, aluminum, magnesium, calcium, and barium, some of which are not broken down in the evaporation and decomposition steps. Thus, a portion of the nitrogen peroxide is not directly available for recycling. Whether or not it is feasible to recover nitrogen peroxide locked in the more-stable nitrates depends partly on the energy required and the conditions necessary for their decomposition.To supply information bearing directly on these subjects, several researches were undertaken at the Pacific Experiment Station: (a) Heats of formation (24, 25, 26) of nitrates of manganese, magnesium, calcium, barium, and aluminum were measured at 298.2° K:; (b) low-temperature specific heats (23), in the range 51° to 298.2° K,, and entropies of nitrates of magnesium, calcium, barium, and aluminumm were determined; and (c) heat contents (21) above 298.2° K. of the nitrates of manganese, magnesium, calcium., and barium were measured. The results of these studies, when correlated by thermodymamic methods, permit evaluation, at any temperature of interest, of the energies required to decomposethe nitrates and furnish information concerning the equilibrium pressure temperature relationships."

Sep 1, 1944

By Seongki Lee

The purpose of this paper is to propose the real-time facility management system framework based on Building Information Model (BIM) and Web of Things. Latest IT such as BIM is rapidly spreading to architecture, civil engineering, engineering and maintenance with the aim of simplifying complex system in buildings and facilities, minimizing operation cost, providing high value services and advancing facility management. In particular, BIM-based management framework design to assist the development of sensor information operation system, which adds convenience to facility maintenance and management, has emerged as a key issue. To this end, this paper proposed conceptual framework for data warehouse, web service and interface that make up real-time facility management system. The paper also produced conceptual methodology on CoRE-based web service platform, mobile device, BIM and WSN mapping.

Aug 1, 2013

By Jack Haptonstall

INTRODUCTION The mines of western central Mexico historically contributed a profusion of gold and silver for the treasury of Spain and later provided sources for financing the Mexican War for Independence and the Mexican Revolution. The western coastal and barranca (cliff) tribes were hunters and extremely hostile, and the Spaniards were not able to penetrate many of the rich districts of their rugged homeland until the mid-1700's. This was more than 200 years after Cortez began the Inquisition by defeating the Aztecs and their allies in a decisive battle in the great city of Tenochtitlan (present day Mexico City). The Spaniards had a voracious appetite for silver and gold, and it was inevitable that they would finally subdue the natives and commence mining activities. Described in this paper are some of the precious metal mining activities in the southern half of the State of Sinaloa and the western half of the State of Durango (Figure l), and specifically those mining activities in the area controlled by the company with which the author was associated for 14 years, Minas de San Luis, S. A. de C. V., the parent company of which is now Industrias Luis Min, S. A. GENERAL DESCRIPTION Geography, Logistics and Climate The most spectacular of the physiographic provinces, the western Sierra Madre Occidental is the cliff or "barranca" province, the

Jan 1, 1983

By Jonathan Peck, Jim Gray

"With the implementation of more advanced monitoring, control and locating systems in surface mines, there is an ever increasing need for their mine-wide integration toward achieving over-all optimization. AQUILA Mining Systems Ltd. is developing the basis for a comprehensive real-time monitoring, control and information system called the Total Mining System or TMS. This system is being designed to address both current and future needs of open pit mines toward improving productivity and minimizing costs, through better two-way information flow between each component in the operation. At a basic level, feedback from equipment and process monitoring will enable decision making to be based on quantitative, on-demand information, thus permitting proactive rather than reactive planning. Dynamic planning would be a valuable tool as market conditions fluctuate, equipment fleets age and variations in the grade, quality, geometry and hardness of the mined material all contribute to either changing production targets or levels of achievable performance. Such a capability could be implemented within the next two years.At a higher level, and within five years, autonomous operation and/or real-time supervisory control of mobile and stationary equipment in open pit mines will be achieved. A discussion is provided in regard to the development and implementation of an autonomous haultruck and blasthole drill, to demonstrate the need for such a system.This paper outlines a preliminary program for the design, development and implementation of this system, primarily in relation to high-level communications and its role in the future automation of open pit mobile equipment."

Jan 1, 1995

By George H. Edwards

Most cullets consumed in large-volume glass manufacturing processes receive little processing beyond crushing. But lead-glass cullets for specialty glasses such as industrial lighting refractors or cathode-ray tubes are combined with metals and various coatings that prohibit their direct recycling into the glass-melting processes that created them. In many cases, the contained lead renders these cullets hazardous. At present, virtually all industrial processes to separate one cullet from another depend on hand sorting, and thus are necessarily costly per unit weight. Lead-glass cullets of differing lead content are of interest because they offer the possibility of separating one glass composition from another by high-speed, automated processes at low cost. A potential process for comminution, cleaning, and separation of lead-glass cullets would involve primary and secondary crushing, magnetic and other metals separation, attrition scrubbing in water, separation of glass types by gravity techniques, drying if necessary, sampling, and preparation for transport to the point of use. Process water would be filtered to remove finely divided coating materials and glass, and reused. If carried out on a scale similar to a specialty industrial mineral processing plant, the cost per unit weight of such processing should be substantially less than the raw material value of the cullet in specialty glass production. The added value of avoiding waste disposal costs makes this process economically attractive.

Jan 1, 1994

By Maria S. Adusumilli, A. Bhaskara Rao

ABSTRACT The presence of gold in lateritic crusts over mafic and ultramafic volcanogenic complexes in / and greenstohe belts, has called the attention in several parts of Brazil and also in Australia. Recent studies reveal the variety of structures and mineralogy of such crusts, and their importance in correlation with host(bed) rock types, as exploration guides, specially for greenstone belt metallogeny. The expected nature of growth of plates and/or nuggets in such crusts is under detailed study, and is considered as possibly due to dissolution and reprecipitation phenomenae of disseminated-fine-low grade ore in the host rock, in this investigation, laterite geochemistry, though incipiently discussed todate, is of fundamental importance and significance. Lateritic gold can be classified texturally as: dusty and diffused, fine, thin platy, taDular, and nuggets. Such gold is pure, and is often restricted to nodular (pisoliths, ooliths, concretions) forms or the matrix, that constitute the crusts or lateritised gravel beds which have an essentially goetnitic nature. Further this gold is recovered directly by mining the crusts or the adjoining placers with the metal derived from them. The thickness and extension of laterite crust zones is extremely variable depending oh the paleoclimatic conditions, and is conditioned to the favourable lithology and its structural expression. However, the "growth" of gold in these laterites will be conductive , without doubt, to several small scale mining activities, specially in the developing countries and regions limited to latitudes 309N and 309S.

Jan 1, 1987

By Anne Kathrine Kalager

"Stretching from Norway’s capital, Oslo, to the city of Ski, a new railway line is under construction with a 20 km long hard rock tunnel. This is a major project with high demands regarding quality, cost and schedule. In addition, restrictions concerning locations close to sensitive urban infrastructure require execution with the highest level of precision and expertise. The new double track railway line forms an important part of the intercity rail development southwards from the capital and includes the longest railway tunnel to date in the Nordic countries. With its novel methods and solutions, this project offers a model for future railway project developments in the region. This paper provides general pertinent details and facts relating to this current railway project and includes a description of the project with information relating to concept and design of the tunnels, geological conditions, particular challenges, selected tunneling techniques and contracting strategies. THE FOLLO LINE PROJECT The Follo Line is a new 22 km long double track railway line under construction between Oslo Central Station and the city of Ski. The project is divided into four subprojects, as shown in figure 1. The main part of the project consists of a 20 km long hard-rock tunnel, which will be the longest railway tunnel in the Nordic countries to date.The Østfold Line is the existing double-track railway line running between Oslo Central Station and Ski serving 12 local stations. The new Follo Line will offer a direct service, without stops, between Oslo Central Station and Ski and reduce the travel time from 22 minutes to 11 minutes. After completion of the Follo Line, these two railway lines will, in combination, more than double the capacity for train transport in the region south-east of Oslo."

Jan 1, 2016

By Alpagut Kara

Turkey is the fifth biggest ceramic tile exporter in the world. Considering the expectation that the Turkish tile sector continues to expand, further studies both on the improvement and the development of tile formulations are necessary in order to make the producers advantaged in the world market while maintaining the capital and running costs at reasonably competitive levels as well. In addition to such studies, waste management in tile manufacturing has also recently become an important issue. Accordingly, the industrial use of wastes in the traditional ceramic industry has been intensively investigated in the recent years. This work describes part of a detailed research project carried out jointly on the possible re-use of muds (raw production waste) from glazing and pressing lines of a local tile company in the development of new wall and floor tile formulations. In order to achieve this, the waste material was firstly investigated in function of chemical and mineralogical compositions. Then, the particular focus was given to the presence of the waste material in increasing amounts on the thermal behaviour and physico-mechanical properties of the re-formulated tile bodies. During the studies, SEM in combination with EDS, and thermal analysis techniques such as non-contact dilatometry were widely employed. The results indicated that it was possible to use the waste materials in the commercial tile production without deteriorating the relevant technological properties.

Jan 1, 2006

Jan 1, 1917

By Elmars Ence, Harold Margolin

The partial isothermal section of the Ti-Cu-Zr system at 750°C has been studied. The crystal structure of Ti2Cu has been detevnlined as tetragonal and when expressed as face-centered tetragonal, a = 4.164, c = 3.611 A, and c/a = 0.867. TITANIUM systems in which ß-titanium decomposes eutectoidally into a and a compound rather readily are known as active eutectoid systems. Recently in active eutectoid alloys based on the Ti-Cu system, and containing additionally A1 and Zr, it has been found that zirconium may produce both moderate weakening and marked strengthening at elevated temperatures.' In order to obtain some insight into the behavior of zirconium, an attempt was made to determine whether compounds of the type Tix Zr and TixZryCu exist. Only results of the Ti-Zr-Cu studies are reported here since data on Ti-Zr alloys will be presented in a separate publication. EXPERIMENTAL PROCEDURE Alloys were nonconsumably arc melted in argon atmosphere as 15-g buttons, prepared from materials of the following purities: Bureau of Mines electrolytic Ti — Bhn 63 OFHC copper Reactor Grade Zirconium Bhn .C 150 Prior to alloy preparation the electrolytic titanium was premelted to avoid excessive spattering of the charges during melting. The weight losses during melting did not exceed 1 pct of the total weight of the charge. The alloys prepared are listed in Table I together with analyzed compositions. in cases where they were determined. Specimens for heat treatment were wrapped in molybdenum sheet, annealed in argon-filled quartz capsules, and quenched by breaking the capsules under iced brine. About 1 to 2 sec are required to remove the capsule from the furnace, drop it into the iced brine and break it. Because of the insulation effect of the quartz, this delay in quenching should not produce a large drop in temperature. In many instances, no difference or little difference has been detected between the same specimen quartz capsule quenched or directly quenched in vacuum by an impinging stream of water.' Ti-Cu-Zr alloys were homogenized for 48 hr at 825°C prior to annealing at 750°C. Annealing for 5 days at 750°C produced the same results as 11 days at temperature and it was therefore assumed that 5 days was sufficient to establish equilibrium. Titanium-copper alloys were homogenized for 40 hr at 900°C prior to heat treatment for 6 days at 750°C. Specimens for metallographic examination were electropolished and etched with the following solution:

Jan 1, 1962

By R. L. Crosby

Microscopical and X-ray diffraction techniques were used to identify two intermediate phases in that part of the solid region of the magnesium-cerium system between and Mg3Ce. Previous literature had reported only one intermediate phase for this region, 1)12t chemical analysis determined the approximate composition of the two compounds to be Mg23Ce2 and Mg17Ce2. The range in composition of the two intermediate phases was found to be limited to less than 0.3 atomic percent cerium. The study did not determine the crystal structure of Mg17Ce2, but that of Mg23Ce2 is tetragonal with a = 10.33 A and c = 19.51 A.

Jan 1, 1966

By B. J. Arnold

During the past three years, coal samples covering a range of coal rank, ash content, size consist, grindability, and moisture content have been tested for their flow properties using a triaxial shear tester that measures the unconfined yield strength in a compressed sample of coal. The ratio of this unconfined yield strength to the sample bulk density is part of the equation used by handling system manufacturers to calculate the critical arching or critical ratholing diameter needed to ensure that coal will flow from bunkers or bins. This ratio also serves as an index to compare the flow tested. To test the applicability of the index to predicting problems with coal flow, a series of tests were conducted at CO Inc.'s Coal Quality Development Center (CQDC) in Homer City, Pennsylvania. Tests covering ranges in size consist, moisture content, and ash content were conducted by first filling a small two-ton bin with coal and then emptying the bin at a pre-set discharge rate. The actual discharge rate from the bin under the various conditions tested was measured. Samples of the coal discharging from the bin were collected. One sample was analyzed for ash, moisture, and size consist; another sample was sent to the Iowa state University for trivial shear tests (supplying an index measurement). Actual flowability results from the bin were then compared to the measured index to determine the applicability of the handleability index in actually predicting coal flow problems. This paper describes the correlation between handleability index and bin flow and explains the next stages of the project.

Jan 1, 1992

By Frank A. Jerabek

Pneumatic stowing was first introduced in longwall mining in the middle twenties. Since that time it has advanced through many stages of development, particularly abroad, which have greatly improved its efficiency and contributed to its growing use. Pneumatic stowing originated in coal mining but has also been adopted in metal mining. This paper discusses the techniques of pneumatic conveying of. stowing material and equipment and applications of pneumatic stowing.

Jan 1, 1966

By Robert Head

El presente texto señala las probables tendencias de la industria cuprífera a lo largo de esta década, donde los pronósticos de una parte se basan en los hechos y datos del pasado, tanto de producción como de consumo. En cuanto la producción futura, ésta se basa sobre disminuciones en minas cuyas reservas se agotan, incrementos de minas en plena vida y minas nuevas o probables que serán llevadas a la producción a través de la década. Como consecuencia de esta posición de adecuado abastecimiento la tendencia a investigar por materiales en sustitución del cobre puede ser reducida. Asimismo, la nueva de producción vendrá de minas más grandes, de baja ley que necesitarán grandes inversiones de capital.

Mar 1, 1971