Search Documents

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°F.) for 15 min., cool rapidly to casting temperature, and cast.' In Germany superheating is carried out at 850' to 900°C. (1560° to I650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (I740°F.).2 In the United States superheating is carried out at 1600' to 1700°F. (871' to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.! in heavy sections and from 60 to IOO in 1/2-in. sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. Materials and Methods The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 Per cent aluminum, 2 per cent zinc, and 0.1 per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By Howard P. Hamlin

This Bureau of Mines report is concerned with the testing procedures for evaluating clays, shales, and slates for lightweight aggregates using the rotary-kiln method of production. To meet the increasing demand for light-weight concrete, rapid, accurate methods for appraising raw materials for light-weight aggregate are needed. Preliminary tests were made on samples of clay, shale, and slate, using laboratory equipment, and the data were used to establish operating conditions for pilot-plant-size rotary-kiln tests. Lightweight concrete was made from the processed aggregates and the properties determined. The results show that the laboratory data can be used to guide rotary-kiln testing, and, with the exception of sampling, a complete appraisal of a raw material for lightweight aggregate concrete can be made in 3 days by the methods described in this report.

Jan 1, 1962

By Martha Caudill

When planning for the required amount of storage capacity at a proposed open-pit coal mine or determining when additional storage capacity should be added to an existing operation, the decision must be based on a breakeven- analysis relating the discounted cost of capital for storage capacity to the marginal costs incurred for additional crew call-outs on weekends and demurrage charges. The model developed in this paper uses simulation techniques applied to two coal mines in the Powder-River Basin to determine how much storage capacity is needed and when it is needed. The paper also generalizes the simulation model so that it can be applied to any type of open-pit mining operation. Two important results of the model are (1) all of the mines in the Powder River Basin have excessive amounts of storage capacity, and (2) management is provided with estimates of the total number of hours that crews will have to work on the weekends as annual tonnage increases, and the levels of demurrage costs incurred.

Jan 1, 1986

By Dennis C. Martin

Assessment of the potential for mining induced subsidence and determination of ultimate design requirements for a mining operation should be based on a number of assessment approaches. Although the rock mechanics engineer has a variety of limit equilibrium and numerical modeling tools available for assessment and prediction of subsidence effects, empirical approaches based on precedent experience provide a powerful tool for calibration/verification of analytical models and prediction of subsidence. Three separate analyses approaches have been applied to the assessment of potential subsidence for a proposed block caving mine in eastern Canada. The investigations have included an assessment of documented historical information from previous block cave mining at the site, deterministic analyses using limit equilibrium approaches to assess kinematically possible failure mechanisms, and three-dimensional numerical modeling techniques. Analyses results have been used and compared with precedent experience and documentation of subsidence behavior from previous mining to optimize the subsidence predictions for the proposed mine.

Jan 1, 1998

Early in 1940 the development and sampling programmes in hand on the North and British Sections of North Broken Hill Limited were such as to necessitate the drilling of a large number of drill holes ranging up to about thirty feet in length. On the British Section, one purpose was to test the existence, width, and value of narrow lodes believed, for geological reasons, to occur in the walls of the existing workings. Another object was to definitely disprove the existence of payable shoots of ore in certain largerhodonite and quartz-garnet ("garnet sandstone") pillars which had been formerly left as unpayable.On the North Section, the main purpose of the short holes was to delineate the ore-body boundaries by drilling laterally from drives in ore, and thus enable level layout to be planned in advance of sill stoping. It was also desired to test the walls of stopes in those portions of the mine where the economic limit of mining is not rendered obvious by a clear-cut wall, but should be determined by assay. In these latter cases it was hoped to eliminate "prospecting by stoping," a procedure by which any doubts as to the existence of further good ore behind the low-grade walls were settled by continuing to stope laterally until all chance of such an occurrence was removed.LONG HOLE ROCK DRILLINGFollowing an investigation of recorded instances of similar practice elsewhere it was decided to use the rock drill for a series of trial sample holes. A 3-in. drifter was used. This was selected from those in use underground, and was given a special overhaul; had a new machine been purchased, a 4-in. type would probably have been obtained as being more suited to the work. The rods were H in. hollow round steel with a type "1" Jackrod thread. Couplings were of chrome steel, and were H in. in diameter, and 2 in. long. Jackbits (type "1" thread) in sizes from 2 in. to 4 in., with 1-in. gauge changes, gave a range of nine bit sizes. They were resharpened by hot milling, and were not milled to a definite gauge size.After sharpening, bits were sent underground without sorting into sizes, the drillers selecting the next bit with callipers. In view of the small scale of operations, it was not considered worth while to adopt special measures, such as the cold grinding of bits, which might have given a better product. Later, however, new bits were used exclusively, the idea being to accumulate enough blunt Jackbits to warrant a thorough treatment of the sharpening...

Jan 1, 1941

By C. E. Tsoutrelis

A new method for determining rock drillability in diamond drilling is discussed; the method takes into consideration both penetration rate and bit wear. The method is based on drilling a rock specimen under controlled laboratory conditions using a model bit. The technique used for determining the experimental variables is extremely simple, quick, and reliable. Drillability is then determined by the mathematics of drilling. In considering the different factors that affect diamond drilling performance, the nature of the rock to be drilled is of outmost importance since it affects significantly the drilling costs and such other variables as bit type and design, drilling thrust, and bit rotary speed. Many attempts have been made to study this effect by correlating actual drilling performances either to certain physical properties of the rock being drilled1-? or to test drilling data obtained under laboratory conditions.7-13 These attempts were aimed at providing a reliable method of predicting by simple means the expected rock behavior in actual drilling, thus giving the engineer a tool to use in estimating drilling performances and costs in different types of rock. The purpose of this paper is to describe such a method by which rock drillability (a term used in the technical literature to describe rock behavior in drilling) could be determined in diamond drilling. It is believed that the proposed simple and reliable method will cover the need of the mining industry for a workable method of measuring the drillability of rocks. It should be emphasized, however, that since drill-ability depends on the physical properties of rock and each drilling process (diamond, percussive, rotary) is affected by different or partly different rock properties,14-l6 the proposed method of determining rock drillability cannot be extended to the other drilling processes. The results presented in this paper form part of an extensive three-year research program carried out by the author in the laboratories of the Greek Institute of Geology and Subsurface Research. During this period the effects of the physical properties of rocks and of such operational variables as drilling thrust and bit rotary speed in diamond drilling were investigated in detail. DRILLABILITY CONCEPT The literature is not devoid of drillability studies. While there are a number of investigators1,3,5-7,9-0,12-13,17 who have attempted to establish by direct methods (i.e., drilling tests under laboratory conditions) or indirect (i.e., through a physical property of rock) an index from which the drilling performance in a given rock may be estimated, very few6-7,9,12, of the proposed methods seem to be of much practical value to the diamond drilling engineer and none to date has been universally accepted. Commenting on the proposed methods for assessing rock drillability, Fish14 remarks that "for a measure of drillability to be accepted it is essential that penetration rate at a given thrust and bit life are elucidated as otherwise the method is of little value." This statement should be examined in more detail by making use of the penetration rate-drilling time diagram obtained in drilling a rock under constant operational conditions. Furthermore, the merits of using this diagram to describe rock drillability will be pointed out. At the same time reference will be made to this diagram when discussing some previously proposed methods. Fig. 1 illustrates such a diagram for three rocks,A, B, and C, which have been diamond drilled under identical conditions. It is assumed here that rocks A and B have the same initial penetration rate, i.e., VOA = Vog, but since rock B is more abrasive than A, rapid bit wear occurs and as a result the fall of its penetration rate with respect to time is more vigorous than in rock A. This is shown graphically by a steeper V = f(t) (0 curve in this rock than in rock A. Rock C has a lower initial penetration rate, due to higher strength properties16 but since it is not very abrasive, only a slight fall of its penetration rate occurs during drilling (in this category are some limestone and marbles with compressive strength above 1000 kg per sq cm). It follows from the foregoing considerations that the characteristic for each rock curve (I) is a function of (i), the penetration rate of the rock Vo recorded at the instant of commencing drilling, which determines the starting point of the curve (1) on the y-axis and (ii), the abrasive rock properties which determine the rate of fall of Vo with respect to time. Thus, curve (I) provides an actual picture of the rock behavior in drilling for given operational conditions, and it can be used with complete satisfaction to assess rock drillability. It can be seen clearly from Fig. I that proposed methods for assessing rock drillability by measuring the

Jan 1, 1970

By R. C. D. Phillis

The management of critical resource inventories is an important productivity lever and a significant risk factor?risk in the sense that poor resource availability lends itself to disempowerment of workers, unsafe work practices, wasted spending (high unit costs),and poor quality of work (including mining waste/rework). Most underground platinum mines experience lost blasts that directly lead to reduced productivity. In most surveyed shafts, 30% of lost blasts can be attributed to shortages of critical material and/or equipment. The problem is prevalent despite the existence of conventional transitory surface and underground stores. This paper discusses the introduction of buffer stores as a complementary materials storage system in order to improve health and safety in mines as well as reduce lost blasts. Both quantitative and qualitative results have shown that buffer stores result in dramatic improvements in productivity and are readily acceptable by stakeholders. Keywords Buffer stores, lost blast.

Jan 1, 2011

The Bureau of Mines extends. a cordial invitation to all members of the Institute to visit Pittsburgh, Sept. 29 to Oct. 1, to participate in the dedication of the Mines Experiment Station. Accompanying this will be a nation-wide participation in a First-aid and Mine Rescue Contest. The Pittsburgh Chamber of Commerce will cooperate. The Institute will be represented by a special delegate appointed by the President. MONDAY 8:30. A. M. Bureau Building open for inspection. 10:30 A. M. Dedicatory Ceremonies in rear of Main Building, .4800 Forbes St. 2:00 P. M.. Special Train and Automobiles to Experimental Mine near Bruceton, Pa. 3 to 6 P. M. Mine Explosion and Inspection of Experimental Mine . and of Explosives Testing Plant near Bruceton, Pa. 6:00. P. M. Return by Special Train and Automobiles to B. & 0. Station, Pittsburgh. 8:00 P. M. Informal Reception and Organ Recital Carnegie Music Hall. Arranged by Carnegie Institute of Technology.

Jan 9, 1919

A shortage of technical skills in all areas of the mining industry is being experienced worldwide. This has significant consequences for design, operations, productivity and safety and, therefore, needs to be seriously addressed, both in the short and longer term. It is therefore both a strategic and a tactical issue. Importantly, however, since mining is a long-term business, the shortage of skills must be dealt with from a strategic point of view to ensure the supply of the necessary skills for future mining. This paper will deal specifically with the provision of high level technical skills, that is, university graduates in mining engineering, and the outlook for the institutions that are currently producing such graduates.

Jan 1, 2009

By Betty L. Gibbs, Jean A. Arcamone

Introduction Microcomputers are becoming more convenient to use at all levels in the business world, including the mining industry. The state of the mining industry requires that we become more productive and innovative in our analysis of deposits and operations. With the help of computers, examination of options to increase productivity can be performed quickly and inexpensively. Effective computer use to design underground workings combines the calculating power and speed of a computer with the technical expertise and judgment of an engineer. Computer programs can perform in minutes calculations that might take several months for an engineer. But the engineer must be on guard when using computers for calculations. It is easy to assume the results produced by a computer program are always correct. However, the computer is only a sophisticated calculator. It cannot recognize logical errors or transposition of numbers. Also, some intuitive or obvious decisions made by an engineer are difficult or impossible to program effectively. In this article, selected commercial programs are discussed. These programs can provide engineers with tools to evaluate engineering designs for underground mines. The programs perform much of the tedious calculation. The engineer, though, must still make decisions and conceptualize designs. The software mentioned in this article runs on microcomputers and minicomputers. The mention of particular software, however, does not imply endorsement. Mining projects After a decision has been made to proceed with an underground mining project, more detailed evaluation of the mining method and extraction sequence begins. If a mine is already in operation, schedules and plans are needed to more clearly define future production. Existing operations can benefit from identification of bottlenecks in material movement and produce extraction options to make the mine more efficient. Detailed studies for a new mine are based on the technical engineering design. These studies provide specific details to determine equipment requirements. Detailed studies done during a project are similar to short-term planning and control carried out daily by the mining engineers. The engineering design phase includes: • Study of the infrastructures - entries, shaft, access from surface to underground; • Definition of the mine layout, hydrogeology, geotechnical considerations, transport, and ventilation; • Choice of machines and equipment; • Mine scheduling, including waste extraction and production sequencing; and • Economics, including labor and supplies. Further detailed studies include: • Blasting patterns; • Detailed geotechnical calculations; • Secondary ventilation; and • Production cycles along with coordination of the workings. Objectives The primary objective of underground mine planning is moving material out of the mine at the least cost. Development of the production schedule considers location and volume of ore units, transport distance, equipment and manpower interactions, and grade or quality of material. Two methods can be used to determine the scheduled material removal: optimization or trial and error. The microcomputer programs discussed here do not cover optimization for underground mine planning. For several reasons, optimization is often a "black box" approach. Although optimization is possible with linear programming techniques, few mining operations can be described effectively with linear equations. An interactive trial-and-error approach is desirable because engineering judgment can be inserted as a plan develops. Because of the large number of factors in an underground operation, an optimization technique seldom covers all possibilities. Few of the programs available consider all of the possible parameters. The programs use an interactive sequencing or a simulation approach and are either event-oriented or deposit-oriented. The most desirable programs offer an integrated approach. They consider a broad range of operating conditions including equipment, labor, costs, material movement, timing, and mine layout, among other factors. The two types of models generally used in designing underground workings include: • The interactive model, which requires direct, incremental input from the user. Outlines of the section to be mined may show on the screen. The engineer causes the model to develop piece-by-piece. The program may offer feedback on parameters such as tons and grade, or other values, as the section is "mined." • The simulation model, which is usually an automatic technique. Parameters related to the process are entered. The program then calculates the mining sequence over a designated time period or until the economic material is exhausted. A simulation model imitates step-by-step performance of equipment or other processes.

Jan 3, 1988

By Kendall E. Born

PRoduction of crude oil in Tennessee during 1938 was slightly more than 41,000 bbl., an increase of about 5000 bbl. over 1937. The production by counties and by fields is shown in Table 1. The increased production has resulted from continued activity in the Upper Cumberland district, especially in Clay County. The "Mississippi lime" production in Scott and Morgan Counties continued to show a further decline with a 1938 production of 12,379 bbl. as against 14,644 bbl. during 1937. Small scattered production from some half dozen wells in Clay, Pickett, and Fentress Counties, on which there are no accurate figures, is estimated at 500 bbl. during the year. The only natural gas marketed off the lease in Tennessee during 1938 was in Morgan County, where a small amount was furnished for the town of Sunbright and immediate vicinity. The gas occurs with the oil in the Boone Camp field and small amounts were put on the line from the near-by Coon Hollow and Seabolt pools. Developments There were 88 wells spudded in during 1938, of which 10 were drilling or only temporarily shut down on Dec. 31, 1938. Eighty wells were completed during the year; 16 produced oil and 3 were gas wells of undetermined quantity. The total footage drilled on 1938 completions was 63,385 ft. Flush production during the year totaled 850 bbl. per day. The more important wildcats are listed in Table 2; the distribution of oil and gas tests drilled during the year, according to physiographic divisions, is given in Table 3. Cumberland Plateau There were no completions in the producing pools in Scott and Morgan Counties. The decline in production in these areas has been steady for the past several years. In an effort to revive production, present plans include a repressuring program in the Boone Camp field in Morgan County early in 1939. There was one completion in Morgan

Jan 1, 1939

By James N. Mure

The paper describes the design development and construction of bored piles at Pindersfield Hospital, Wakefield, U.K. The piles were of monopile type. Monopile is the term used to describe piles which are constructed without pile caps so that the superstructure columns bear directly on the pile top. Pile geotechnical design was developed from the Site Investigation data and testing of two preliminary piles. Final design philosophy is described. Pile structural design was developed from the loadings applied by the superstructure, and the requirements, tolerances and limitations of monopile construction techniques. Construction was closely controlled in order to achieve a ?right first time? result. The conclusion gives a critique of the system and its value.

Jan 1, 2008

By Jean-Luc Cornet

Advances in conveyor technology over the past decade have enabled the design and erection of very long overland belt conveyors. Such conveyors usually require head and tail drives to lower the belt tension and belt strength required. This paper provides an overview of the problems encountered in controlling the head and tail drives on such conveyors and some of the solutions developed by CDI for several such projects.

Jan 1, 2002

By Phillip J. Mackey, Susumu Okabe

Copper mining and smelting has been carried out in Japan for over 13 centuries and in fact stretching back into antiquity. In 1889, the first electrolytic copper refinery in Japan based on Elkington’s principles was started by Furukawa Mining at Honjyo in downtown Tokyo based on the multiple or parallel system. Within two decades, a number of other copper refineries had begun operation. Interestingly, but perhaps not surprising given Japan’s long history of copper production, this first refinery in Japan commenced just ten years after the first refinery in the USA (1879), and not long after the first plants in Europe. By 1935, as a result of growth in copper demand, there were six domestic copper electro-refineries in Japan with an installed capacity of 97,800 tonnes/a, while actual production was 71,200 tonnes/a. Since about 1932, the majority of these plants were based on the more common parallel or multiple system. In 1946, just after World War II, domestic production capacity had dropped considerably to 29,000 tonnes/a, however with reconstruction, capacity and production expanded rapidly, with production reaching 81,000 tonnes/a in 1955, 187,000 tonnes/a in 1960 and 307,000 tonnes/a in 1965. The introduction of the first refinery and the early ones that followed and subsequent developments are discussed in this paper. The major technical achievements during the high growth period from 1945 to 1963 included: the use of fire- refined anodes; the introduction of newly-developed rectifiers; the introduction of lead-lined or vinyl-lined concrete cells; improvements in the electrolyte heating system; application of improved anti-corrosion materials and the introduction of heat-insulating surface coverings. In 2018, Japan’s refined copper production totaled 1,595,000 tonnes of copper, with Japan ranking third in the world after China and Chile. INTRODUCTION In 2018, Japan’s refined copper production totalled 1,595,000 tonnes of copper and Japan ranked third in the world for refined copper after China and Chile (Wood Mackenzie, 2019). There are now eight copper refineries in Japan which provide Japan’s production of refined copper. These plants are listed in Table 1 (Wood Mackenzie, 2019), also showing the production trend since 2013; in general, production over this period has been relatively steady. The Toyo plant is now the 7th largest copper refinery in the world after several large plants as rated by capacity in China, Russia and India (ICSG, 2019).

Jan 1, 2019

By Renato G. Bautista, Gary A. Beetner, Anthony L. Frey

A multistage mixer-settler extractor described in earlier hydrodynamic studies was simulated on a computer. A mass transfer mechanism was derived based on a pseudo distribution constant and a pseudo first-order rate constant. The constants were adjusted to give the proper output concentrations and proper form of the stage-wise concentrations. The results obtained by computer simulation of start-up conditions show very good agreement with experimental data. A second simulation was constructed which demonstrated that the model can be greatly simplified and still yield good results.

Jan 1, 1974

By S. R. Gilbert, B. W. Burdett, L. B. Hales

A brief review of grinding control systems is given with a review of the most popularly reported control loops. The trend toward more sophisticated control systems in terms of control strategies and control equipment is discussed, and the reasons for the popularity of distributed control equipment are outlined. The evolution of the interface between the operator and the process and its importance in plant control is described. Finally, the authors' view is given as to the future of grinding control.

Jan 1, 1984

By V. N. Antaki

ELEMENTAL phosphorus (referred to as P,) is a true mineral product that has developed, in the relatively brief span of a century, from a laboratory curiosity to a heavy chemical. Annual production now exceeds 300,000 short tons. Continued rise in production has been predicted, consistent with new applications for P, derivatives and the expected population increase. In itself elemental P, is valuable chiefly as an 'intermediate chemical. The principal end uses at present are in inorganic phosphates, both simple and complex, of sodium and potassium, used in water treatment and detergent compounds, leavening agents, food supplements, and dentifrices. Organic P, compounds are important as plasticizers, oil additives, flotation agents, and more recently as gasoline additives (TCP being the outstanding example). The increasing use of high-analysis water-soluble and liquid solution fertilizers, as well as the direct application of phosphoric acid to the soil, will probably be the most significant factors in P, production growth rate. Coke oven plants now using sulfuric acid to fix byproduct ammonia values will gradually switch to phosphoric acid in order to market a fertilizer with completely available values. Recently sponsored experiments show that phosphoric acid can be directly admixed with cattle and poultry feed to produce rapid growth. Both P, compounds and modifiers for oil well drilling mud show increasingly promising significance.

Jan 3, 1957

By J Guo, K Williams, S Caldwell, W Chen

Mining is increasingly occurring near or below the water table. This has led to a higher rate of handling problems associated with increased moisture and increased adhesion, which lead to a higher rate of blockage events within the materials handling chain. Typically, these ores and minerals are known as ‘wet and sticky materials’.Currently there is very limited knowledge and/or methodologies for effective design of efficient materials handling systems when it comes to handling wet and sticky materials. However, there is one major parameter that significantly affects handleability of a wet and sticky ore; namely, its moisture content. Flow property testing has shown that when moisture is reduced, the adhesive properties of the ore are also significantly reduced, thereby increasing ore flowability.The research embodied in this paper investigates the moisture reduction rate through a loose packed bed of iron ore using dry, ambient temperature airflow. A comparison of the predictive capabilities of a proposed drying model to data obtained from on-site experiments using iron ore fines is made. Building on an assumption made by Hukill (1954), a second term has been proposed to account for rewetting effects in the drying process. From this research, identification of improved moisture reduction approaches is envisaged.CITATION:Caldwell, S, Williams, K, Guo, J and Chen, W, 2017 Aeration induced moisture reduction of iron ore, in Proceedings Iron Ore 2017, pp 455–460 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides (MA) can be incorporated for use as a transmutation fuel. This study involves characterization of precursor powders and pellets to be inserted into the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U80Pu20)O1.98, and two compositions of MA-MOX with oxygen to metal ratios (O/M) of (U75Pu20Am3Np2)O1.98 and (U75Pu20Am3Np2)O1.95. The precursor powders, which consisted of, highly enriched uranium oxide, HEUO2, depleted uranium oxide, DUO2, neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a field emission gun scanning electron microscope (FEG-SEM) for particle morphology, size, and size distribution prior to pellet production.IntroductionThe Global Nuclear Energy Partnership (GNEP) was created in order for “fuel-cycle supplier” nations to provide assured supplies of nuclear fuel to “fuel-cycle customer” nations. The customer nations would utilize the fuel for electricity generation and subsequently return it to the supplier nation after it is spent. This spent fuel would then be reprocessed by the supplier nation in order to recycle the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials would also be strictly controlled through the International Atomic Energy Agency. One of the thrust areas for the GNEP program is the development of these actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3]."

Jan 1, 2008

First, a classification of the various primary sources of feed materials for the production of cobalt is presented from a mineralogical point of view : sulfides, arsenides, sulfo-arsenides and oxide minerals. Each of these cate- gories will be characterized by its behaviour towards concentration methods, taking account of the presence of the associated minerals of other metals and of the nature of the gangue minerals. Then, for each category of cobalt bea- ring ores, typical flowsheets of treatment will be presented and discussed and the characteristics of the cobalt concentrates produced will be under- lined having in view their subsequent processing by pyro - and (or) hydrome- tallurgical methods.

Jan 1, 1988