Search Documents

By Ilhan Chang, Ernest Nsabimana, Kiseok Kwak, Juhyung Lee, Young-Hoon Jung

"Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.IntroductionWith the development of offshore technology, applications and real site installations of suction piles are increasing significantly nowadays. They are generally used as mooring anchors in various floating structures, marine platforms, and offshore wind turbines. According to its convenience in installation and removal, suction type foundations are becoming good alternatives for deep ocean support systems. The bearing capacity is similar to the bearing behavior of ordinary offshore structures (piles or drilled shafts). The most common use of suction caissons is anchors for catenary mooring lines, where the chain angle at the mudline is close to zero (Randolph, 2002; Sharma, 2004).Recently, it is reported that a huge isolated single suction pile can be replaced by a group of moderatesized suction piles (Randolph et al. 2004). A single monopile is easy to be produced and installed in site. It is expected that monopile foundation is not applicable for deep depths because it has a limitation on penetration according to its huge side skin area (i.e. friction). Moreover, stiffness requirements sometimes render thicker pile wall conditions which are impractical to be produced."

Jan 1, 2017

By Pétroleur Maatschappiju, N. V. de Bataafsche

Jan 1, 1939

By Arturo Ressi di Cervia

"The Construction of the Thrust Pits for Jacking of the I-90 Tunnel for the Central Artery/Tunnel Project (Part of Contract No. C09A4) in Boston MA was nominated for DFI’s 2002 Outstanding Project Award. In the judging, the project and the specialty subcontractor, Treviicos Corporation, was chosen for a Special Recognition Award. INTRODUCTIONBoston’s Big Dig, as the construction of the underground artery became known, is undoubtedly the largest urban construction project of this century.The Central Artery/Tunnel Project, or CA/T, to call it by its proper name, runs approximately eight miles through the heart of Boston, five miles of which are built underground while maintaining traffic on the elevated existing structure, while at its southern end I-90 is extended to Logan airport under active rail lines, Fort Point Channel and Boston Inner Harbor.Since the alignment of the road closely parallels the shoreline as it existed in colonial times, the cut and cover construction had to contend with substantial portions of filled ground, not to mention existing subway lines, live utilities, building foundations and, last but not least, the irritable Boston drivers and litigious adjacent property and business owners.Consequently, while it is impossible to single out the most difficult or challenging contract, the jacking of the tunnels of I-90 under the live rails of Amtrak certainly will rank high on the list.Never before, anywhere in the world, was an attempt made to jack tunnels of this size: the South Bay Interchange consists of three 78 feet (24 m) wide by 38 feet (11.6 m) high tunnels, the shortest of which is 167 feet (51 m) long. TECHNOLOGYIn order to achieve this engineering feat it was necessary to consolidate the soil under the track to prevent it from moving or settling during the jacking process. After a detailed analysis of the geological profile to be traversed it was decided that freezing was the most suitable method, since it could be applied to the full range of soils present on the proposed alignment."

Jan 3, 2003

By Frank W. Luerssen

Introduction "Austerity" is perhaps an overly generous description of the past three years in the American steel industry. Steel plants operated at an average of only 57% of their capability in 1982-84. The dismal losses for last year are still being totaled. But during the two years before this period, American steelmakers recorded an aggregate net loss of a staggering $6.8 billion. Steelmakers responded by closing numerous marginal facilities. And production capability was cut by 13.6 Mt (15 million st). Capital expenditures still averaged $2 billion annually. But this was inadequate to maintain the existing base of steelmaking facilities. The general economy experienced a satisfactory recovery during this period. American steel, however, continued to suffer from a lagging recovery in the capital goods sector. This was due to record penetration of its domestic market by imports and from very weak realizing prices on the volume that was available. In addition to the direct influx of offshore steel products - which itself depressed prices - the industry also became painfully aware of the growing importance of "indirect" imports. These came in the form of steel-containing producer and consumer durables. Industrial equipment and autos fabricated from foreign steel accounted for the equivalent of 6 Mt (6.5 million st) of lost market opportunity for domestic steel-makers last year. That is over and above the 23.5 Mt (26 million st) of direct steel imports. Given these factors, Inland Steel was not spared from the threeyear downpour of red ink. Despite its record of continuing modernization in steel, our single-plant location in the world's best steel-consuming market, and the high proportion of consumer durables related products, such as cold rolled and coated sheet in our mix, Inland suffered aggregate losses of $277 million during the 1982-84 period. Strategic Planning The foregoing establishes a perspective - a base from which we have restructured our view of the steel industry, and of our own role within that picture. Until possibly two years ago, this present weakness in steel demand was viewed around the world as an aberration, eventually to pass. By contrast, it is now recognized that austere times are the normal steel environment. The topic here is management of resources. This implies an emphasis on strategic planning. It is worthwhile to examine some of the more critical assumptions that were driving strategies among a number of steel companies just before the 1980s. Those projected characteristics of the future steel environment were arrived at through painstaking analysis. They were carefully and heavily quantified and were generally shared by outside observers and our peers within the steel industry. • First, the assumption was made that domestic steel demand would continue to grow at an average rate of 2% per year. • Second, it was assumed that this growth in the American market would continue to be filled predominantly by US mills. It was believed that increases in steel and steel-related demand overseas would absorb much of the ominously growing capacity of third

Jan 6, 1985

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 3. t. u. compared with 597,000 3. t. u. in 1936. These amounts represent roughly the heat ob¬tainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at rep aeries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels wore 11 percent higher than in 1930; the average operating ratio was 93 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 639,149 billion 3. t. u. in 1936 to 663,966 billion 3. t. u. in 1937.

Jan 1, 1938

By H. R. Batchelder

Much information on oxygen production and the manufacture of synthetic liquid fuels has been published during the past several years. From time to tine the investment and operating cost of oxygen plants of various sizes has been estimated. Surveys have been made so that the various processes by which oxygen is produced commercially might be compared. The gas-making processes in which oxygen is employed, which wore used in Germany during the war, have been described in T.O.M. reels, and this information has been published. Descriptions of pilot-scale or proposed commercial plants for the production of synthesis gas or hydrogen and their conversion to synthetic liquid fuels also have been published. In general, each of these publications has dealt with a particular phase of the over-all problem. The present paper will discuss the relationship between these phases: The factors that affect oxygen manufacture and costs, the methods for the use of oxygen and for the production of synthetic liquid fuels, and, to some extent, the economic factors that must be considered.

Jan 1, 1951

By Doug Halbe

A number of CIP plants have been built in Western Australia in the past two years. The authors have surveyed several of these new plants and present drawings, data and discussion of operating and design innovations and areas of interest.

Jan 1, 1982

By Moore A. J

This paper describes the use of a wavefront reinforcement model which has been developed to supplement established charge mass scaling methods. The model allows for the time taken for blast vibration wavefronts to travel from each blasthole, and has been successfully used to explain the reason for directional increases in both air and ground vibration in certain situations. The model has been used to identify wavefront reinforcement due to the propagation of air vibration and ground vibrations in certain situations. The paper includes a throw (or cast) blasting case history which provides multi-station evidence of the strong directional nature of wavefront reinforcement.

Jan 1, 1995

By H. F. Winham

The history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smack-over oölitic lime and 116 successful wells have been drilled. The field, which was developed on 40-acre spacing, has been under strict control. It is believed to be producing with a strong water drive, To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. Early History The Magnolia field is in colurnbia County, Arkansas, T. 17 s., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 11/2 miles northwest of the Kerlyn oil Company's discovery well and was based on surface geological work done by Jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil Or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett NO. I was located in sec. 13, T. 17 S., R. 20 W., 3/4 mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime productioil in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1937, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company's Barnett No. I, Sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a depth of 6325 It. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smaclrover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well

Jan 1, 1943

By C. O. Brawner

The advent of larger drilling, excavation, and milling equipment is resulting in a tremendous increase in the scale and annual tonnage of open pit mining. At the present time, open pits up to 3000 ft. deep, and tailings dams and waste dumps up to 600 ft. high are being planned. One of the major problems that projects of this magnitude create is stability. Stability at open pit mining developments must be assessed for tailings dams, waste dumps, and open pit slopes in overburden soil and in rock. Soil mechanics principles are used to assess the stability for the first three. This science was developed by Dr. Karl Terzaghi in the 1920’s, and since that time the theories and principles have been tested and evaluated. This experience has resulted in the development of sound theoretical concepts, workable sampling and testing techniques, and accurate methods of analysis. Typical problems that can be analyzed include: -bearing capacity of soil under dams and waste dumps. - amount of seepage under and through dams. - stability of slopes and determination of safe slope angles for tailings dams, waste dumps, and open pits. - influence of earthquakes on stability. - influence and cost of different excavation and construction techniques. To assist in comparing engineering experience, an international soil classification system has been developed and used for several decades. In addition, many excellent text books are available outlining soil mechanics principles and techniques. A high degree of technology exists in soil mechanics. This, the mining engineer cannot afford to ignore. If soil mechanics principles had been applied, many major failures involving tailings, tailings dams, or waste dumps, such as those at Aberfan, Mufulira, Luanshya, and El Cobre would not have occurred. Tailings dams are planned in Canada that will be up to 600 ft. high. Construction procedures used in the past have paid little attention to the compaction of the shell material or to the influence of earthquakes on stability. This neglect has led to failures. While failures in low dams may not be too serious, for high dams such failures could have catastrophic results. Another major area of concern is the stability of rock slopes. From the standpoint of long

Jan 1, 1971

By Michel Boisvert

Noranda Metallurgy is presently completing construction of the new Noranda Converter (NCV) at its Home Smelter in Rouyn-Noranda. This capital investment of CDN$56M is the continuation of the Emissions and SO2 Reduction Program that was initiated in the late 1980s with the acid plant for Reactor off-gas treatment. The Patented Noranda Converter was developed and pilot tested at the Home Smelter in the early 1990s. The project will replace the Peirce-Smith Converters and enable sulphur fixation to be 'increased from 70% to over 90% by 2002 with an accompanying reduction of dust emissions to the atmosphere. The construction site is an extension of the present Noranda Reactor area. A number of existing facilities including the acid plant and process air supply were used to minimize the capital cost of the project. This paper provides a brief history of the Noranda converting process, the Home Smelter Emissions and SO2 Reduction Program, ,project implementation and construction, a description of the different facilities, and preparation of human resources for start-up.

Jan 1, 1998

By Tell Ertl, Ernest E. Burgh

INTRODUCTION THE Bureau of Mines is operating an oil-shale mine 10 miles west of Rifle, Colo., as part of its Synthetic Liquid Fuels program. The purpose of operating this mine is twofold: First, to supply oil shale to an experimental processing plant; and second, to develop practices and select methods for mining oil shale on a commercial scale at the lowest practicable cost. The second purpose-that of finding out how to mine oil shale most cheaply-entails considerable mining research. Since the drilling of oil shale probably will be one of the major items of the mining cost, factors that influence drilling speeds were investigated. One phase of the drilling program was the development of a successful hard-surfaced rock-drill bit1 that can be used for drilling long holes in oil shale without changing bits. During that phase, drilling speeds were measured and drill cuttings were collected for assay and for screen sizing. When the cuttings from the individual tests were compared, a definite relationship was shown to exist between the drilling speed and the coarseness of the drill cuttings. PROCEDURE Measurement of Drilling Speeds All drilling in the tests was done with a Model UMB-D-99W Gardner-Denver wagon drill. Round-lugged drill steel, 1 ¼ in. in diameter was used in 6, 12, and 18 ft lengths with 2 1/8 -in. Timken H-type bits hard-faced with acetylene tube borium. The tests were made in the lower adit of the Bureau of Mines oil-shale mine; the grade of the oil shale drilled ranged from 18.6 to 42.7 gal per ton. During the experiments air pressure varied between 75 and 90 psi while water pressure remained fairly constant at 75 psi. All holes were drilled almost horizontally. Each drill hole was thoroughly cleaned of cuttings after being collared. The advance of the drill along the carriage was measured and recorded as the drilling speed in inches per minute. Method of Collecting Cuttings To facilitate the collection of cuttings, each drill hole was collared in a smooth, vertical portion of the oil-shale breast (Fig 1). A galvanized-steel sheet was fastened to the breast below the area in which the hole was to be drilled. The cuttings washed out of the drill hole by the drilling water were guided by the steel sheet into a wooden box. The cuttings that remained in the drill hole after the drill was withdrawn were scraped out and placed in the same box as the cuttings washed out of the hole. After the cuttings from a 1-min. drilling interval were collected, they were placed in flat metal pans. The fines were allowed to settle and the clear water was decanted. The cuttings then were dried in the sun.

Jan 1, 1947

The occurence of high silver values in the oxidised zone of the main lode at Broken Hill is well known as a large factor in achieving the early fame of Broken Hill, and the minerals of this zone form a long list, which has been tabulated by G Smith*, and includes...

Jan 1, 1926

By W. Lodge, G. Rasmussen

"The carbon-in-pulp (CIP) process has been the dominant gold recovery technology since the 1980s. During all this time carbon measurement, and control of the carbon transfer pumps has been largely manual in nature. Such manual operation inevitably limits process efficiency, potentially resulting in higher gold solution losses, and higher cost of circuit operation. Based on the authors’ experience, average plant solution loss is in the range of 0.02-0.03 ppm Au, as opposed to the general industry target of 0.01 ppm Au or less. Gekko Systems, in conjunction with Curtin University’s Gold Technology Group, has developed a carbon concentration meter, the ‘Carbon Scout’ meter. The meter automatically measures carbon concentration in all tanks, providing more frequent and more precise data. Combined with SIMCIL, a CIP circuit process model which is used to determine the optimum set points for the circuit, the meter should ensure lower gold solution losses, and more efficient operation of the carbon circuit. This paper will review they critical factors for good carbon management, the development of the meter and results from the first plant installation. Additional benefits of the Carbon Scout, including improved health and safety and the opportunity to measure other key variables in the leach/adsorption circuit from one central location will also be described.INTRODUCTION The carbon-in-pulp (CIP) process was first introduced to the gold industry in the early 1950s at the Carlton Mill in the USA (Fast, 1988), with the modern version of CIP becoming fully developed with large scale installations in South Africa in the late 1970s (Laxen, 1982). CIP quickly became the technology of choice for new operations, and for the retrofitting or upgrading of existing operations. In the 1980s the carbon-in-leach (CIL) circuit configuration became the process design of choice due mainly to its lower capital costs. With 40 years of operational experience, CIP/CIL for gold recovery is now mature a technology, whose operations and limitations are well understood. To extract further efficiencies from such technologies, by improving recoveries and/or reducing operating costs, is challenging and may require new approaches to circuit management. Gekko Systems, in association with the Gold Technology Group at Curtin University, has developed the Carbon Scout, an automated carbon measurement device. This device replaces manual measurement of carbon concentration in carbon adsorption tanks, providing more frequent and more accurate data for control of the CIP process. Data from the Carbon Scout can be used to automatically control the carbon forwarding pumps."

Jan 1, 2018

At the Highway gold deposit, 37 kilometres south of Charters Towers, gold mineralisation occurs in several stratiform layers and is enriched near the surface by lateritic weathering. The host rocks of the mineralisation are ferruginous and baritic, intensely sericitised, kaolinised and silicified rhyolitic tuffs and pyroclastics of the Cambrian-Ordovician Mount Windsor Volcanics. The geology of the deposit is illustrated in Figures 1 and 2.Forty-six reverse circulation percussion drill holes were completed by North-Queensland Resources N.L. for a total of 2,093 metres of drilling to further outline and test the open pit resource. The drilling indicated a resource of 171,000 tonnes averaging 4.4 grams per tonne gold and 5.0 grams per tonne silver.A shallow initial pit, approximately 30 metres deep, has been designed to mine the high grade upper portion of the western stratiform layer and part of the eastern layer. This initial pit is designed to mine 45,400 tonnes of western mineralisation at an average grade of 7.84 grams per tonne gold and 22,200 tonnes of eastern mineralisation at an average grade of 1.42 grams per tonne gold. Waste is estimated at 110,900 tonnes.

Jan 1, 1986

This paper intends to give an insight into what is often considered to be a poor relation of the mining industry but is in fact an integral part of any community. Aggregate production accounts for more than half of the world production of minerals by weight. In New Zealand production of aggregates runs at around five tonnes per capita per year, making it a significant industry. The industry in this country is dominated by smaller operations close to the market due to the widespread population and relative abundance of aggregate. The Logan Point quarry is one of the largest quarries in the South Island with an annual production of around 250 000 tonnes. The market is mainly based around roading and building in the Dunedin area with some higher quality specialist aggregates being used allover Otago. The quarry has been owned and operated by Palmer and Son Ltd for 106 years with a fifth generation family member the current quarry manager.

Jan 1, 1992

By Steve Kral

The Society for Mining, Metallurgy and Exploration’s origins can be traced back to 1871. This was when 22 Pennsylvania coal mining engineers founded the American Institute of Mining Engineers (AIME). The organization’s objective was to “promote the arts and sciences connected with economic production of the useful minerals and metals, and the welfare of those employed in those industries by all lawful means.” Metallurgy and Petroleum were added to the AIME name in 1919 and 1956, respectively. Divisions of AIME were formed throughout the following years in recognition of the increasing trend toward specialization among mineral industry engineers. At the time, SME’s divisions consisted of the Coal Division (1930, now known as the Coal and Energy Division), the Industrial Minerals Division (1935), the Mineral and Metallurgical Processing Division (1948) and the Mining and Exploration Division (1949). The Environmental Division was created in 1997.

Jan 1, 2007

Total U.S. mineral production reached an estimated $17.8 billion for 1960, 4 pct above 1959 and second only to the record high of $18.1 billion established in 1957. As a group, metals achieved a rise from $1.6 billion in 1959 to $2.0 billion this year, an increase of 28 pct. Similarly the value of nonmetallic production including fuels (i.e., natural gas, petroleum, natural-gas liquids, asphalt and related bitumens, carbon dioxide. anthracite. bituminous and lignite coal, peat, and helium) rose from $15.5 billion in 1959 to approximately $15.8 billion in 1960. However, this 2 pct increase in the total value of non-metallic production was due to an increase in the value of the fuels ($11.8 billion in 1959 to $12.2 billion in 1960) which offset a drop in value of the other nonmetallic minerals ($3.7 billion in 1959 to $3.6 billion in 1960).

Jan 2, 1961

By Peter F. Strong, Robert L. Lagace, Alfred G. Exslie

The theoretical study of WF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer is the concern of this paper. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. The theoretical results are compared with published measurements. This work was part of an investigation of new ways to reach and extend two-way communications to the key individuals who are highly mobile within the sections and haulageways of coal mines.

Nov 14, 1974

Poorly designed sampling protocols generally result in high project risk by artificially increasing grade variability (ie the nugget effect). Sample collection, preparation and assay protocols that suit the ore type, together with QA/QC systems, will reduce this risk. All reporting codes (eg JORC, 2004) require the Competent Person to consider the quality and implication of sampling and assaying programs. High sampling errors beget higher project uncertainty; despite this fact, sampling does not receive the attention it deserves. The case studies presented show that many sampling issues frequently go unrecognised or unaddressed, resulting in poor project decisions during exploration through to feasibility and production. The overall conclusion is that correct sampling is critical to mining project success and that there is often a need for its optimisation.

Jan 1, 2007