Search Documents

The mathematical modelling of rock fragmentation by blasting is one of the most difficult and challenging problems of applied mathematics. Not only is complex mathematics required but there is incomplete understanding of the basic physics and chemistry involved. The possibility of getting the physical basis of a model correct by simple mathematical and experimental procedures is demonstrated for the novel process of fragmenting rock by high-pressure arc discharges. While the importance of obtaining the correct physical basis for a model is emphasised, high-pressure arc induced fragmentation of rock is shown to be a powerful laboratory tool for the study of blasting.

Jan 1, 1990

By Mitchell D. S

BackgroundIn March 1990 Pasminco resolved to replace and increase the capacity of the underground pumping system at the Southern Operations, Broken Hill. The existing pump station was built 23 years ago while the rising main had been in service for 38 years and was subject to frequent failure.The old system was a conventional slurry/clear water separation and multi-stage pumping system. It was inadequate in the following areas:ò insufficient capacity to handle current and expected future flows;ò unable to consistently dewater lower production areas; ò pumping capacity restricted sandfilling rates;ò dirty water dams had insufficient settling capacity and were difficult to de-sludge;ò the operating costs of dewatering were high; ò it was labour intensive; andò it did not offer enough protection to the 25 level loading station.

Jan 1, 1993

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1936

"When a metal-mining company takes out a workmen's compensation insurance policy, it does so to relieve itself of its uncertain and variable financial liability under laps requiring payment to employees for lost-time accidents, there-by passing the liability or to the insuring agency. For this service, or rather for the assumption of the risk, the insuring agency charges the mining company a price, or in insurance parlance, ""a premium"".The insuring agency depends upon a volume and variety of business to average the losses incurred by its individual policy holders, and determines its price to cover losses that are suffered and its cost of doing business.It is generally known that all types of insurance are founded on the theory of probability applied to large groups of risks, Workmen's compensation insurance is no exception, and the average price paid therefor must be based on the frequency and severity of accidents in the particular industry or branch of industry under consideration. The frequency and severity rates are determined by statistics, which, of course, unless standardized, kept carefully and consistently, and analyzed properly, are liable to be inaccurate and misleadingThe importance of large groups in arriving at an average price for insurance service can not be overestimated, For example the writer knows of one small group of some twenty metal-mining companies whose losses during the past two years exceeded their premium charge by 54%. Not a single individual company during the two years kept its losses below the premium rate. For several years the group as a whole has persistently exceeded its premium rate, Such risks are not profitable to the insuring agencies and can only be carried where a large volume of good risks will balance the poor risks, but in order to conform to good insurance ethics the premium rate must be based on averages for the industry as a whole, and kept sufficiently low to induce operators to sell their risks."

May 1, 1924

By Smith J. W, Wilkins R. W T

This paper is a preliminary report of research on the Mount Morgan gold-copper deposit being done at the Division of Mineralogy, CSIRO. Fluid inclusion and sulphur isotope measurements were made on a suite of 11 samples collected by the staff of Geopeko Ltd. This suite contained representatives of the main ore and rock types of the deposit. Homogenization temperatures of fluid inclusions measured on quartz from 8 of the 11 samples, ranged from 172¦C to 276¦C and to this must be added a pressure correction (in this case, up to 50¦C) to obtain the formation temperature of the mineral. Sulphur isotope measurements were made on 34 sulphides from 8 of the 11 samples. The 6S values form a well defined group ranging from -0.5%oto +3.6%owith a mean of +2.4%c. Although the preliminary data do not indicate unequivocally the origin of the deposit they do impose restraints on the wide ranging suggestions that have been put forward. This work is complementary to the paper of Dr G. Gibbons who has described other mineralogical aspects of the Mount Morgan deposit, based on a more extensive suite of Samples.

Jan 1, 1974

By J. D. Bosman, L. J. Gardner

"The Bushveld Complex is a large layered igneous intrusion, located in the northern parts of the Republic of South Africa. The complex hosts the largest known reserves of Platinum Group Metals in the world. On the western limb of the complex, mining of the Merensky economic horizon and UG2 chromitite layer has been conducted for many years by several mining companies, including Impala Platinum Limited. Over the past decade, Impala has planned a new generation of greenfield vertical shafts, commencing with comprehensive geological and geotechnical studies. As part of the geotechnical studies, numerous tests have been conducted to quantify the mechanical properties of the various near-reef rock types. These tests include point load tests conducted in the field, as well as uni-axial compressive strength, triaxial compressive strength, and Brazilian disc tensile strength tests conducted in specialist laboratories. The authors have compiled an extensive database containing a large number of tests for different rock types, ranging from felsic Anorthosite to mafic Pegmatoid. The database was analysed to quantify the mechanical properties and values for Mohr Coulomb and Hoek Brown failure criteria for each rock type typically exposed by mining. The paper will provide a data set of rock mechanical properties typically used in numerical modelling and other design processes. Using the significant number of tests available, data describing the variability of the various parameters will be included."

Jan 1, 2015

Traditional fine-grinding mills in mineral processing rely on the use of steel medium for particle size reduction. The IsaMill (a horizontal stirred mill with a 3, 000-L net chamber volume and a rated motor power of 1,120 kW) has successfully adopted a novel product-separator design, which has led to a major revision of medium use in fine grinding. The IsaMill separator has successfully operated with a wide variety of medium types, such as silica sands, river gravel, smelter slag, run-of-mine ore fractions and steel shots, with sizes ranging from 0.5 to 10 mm. Great flexibility in the IsaMill operations has been achieved for processing feed as coarse as 120 µm to a product as fine as 5 µm. This paper discusses the performance of two inert grinding media in the IsaMills that are used at Mount Isa Mines Ltd. for the processing of galena- and sphaleritebearing ores to below 10 µm. They are the copper reverberatory furnace slag (CRFS) and the heavy-medium plant rejects (HMPR). A methodology was also demonstrated for comparing the medium performance and for scaling up the IsaMills from a 1.5-L laboratory batch mill to a full-scale 3,000-L mill.

Jan 1, 2002

By R. W. Heckel, R. A. Tanzilli

Treatment of the finite, diffusion-controlled, two-phase, moving-interface homogenization problem has been carried out by numerical methods for a wide range of input parameters. Solutions have been obtained for planar, cylindrical, and spherical diffusion geometries. The effects of parameters such as the interdiffusion coefficients (concentration-independent) of- both phases, the concentrations (time-independent) of each phase at the interlace, mean composition, initial size of the dissolving- phase, and initial composition of- the two phases are considered. The results are displayed to show both the position of the interjace and the degree of homogenization (expressed in terms of concentration at the matrix phase symmetry boundary) as a function of diffusion time. Typical exaw~ples to which the results may be applied are discussed. A limited number of exact, closed-form solutions to the multiphase, diffusion-controlled, moving-interface problem exists in the literature, e.g., Refs. 1 to 7. The exact, closed-form solutions generally consider the outermost phases to be infinite in extent and also assume an interfacial velocity function. It is through use of such boundary conditions that closed-form solutions are readily obtained. An extensive literature also exists on numerical solutions to the mathematically analogous solidification problem, e.g., Refs. 8 to 12. In addition, a numerical solution involving mass transfer with spherical interfaces and infinite boundaries has recently been carried out.13 A practically important class of diffusion problems exists, however, in which the boundaries of each phase away from the interface are finite. For example the finite boundary condition arises when one sets up a model for analyzing the homogenization behavior of two-component powder compacts in two-phase systems or for studying the solution behavior of precipitates. Although exact, closed-form solutions have as yet not been found to this class of problems, solutions are possible using numerical methods. The purpose of this paper is twofold: 1) to describe a numerical method for treating the two-phase, diffusion-controlled, moving-interface problem involving finite boundaries with planar, cylindrical, and spherical interfaces; 2) to present the results of a parametric study which identifies the role played by each variable appearing in the analytical model. R. A. TANZlLLI,Student MemberAIME,onleaveofabsence from the General Electric Co., Re-entry Systems Department and A. W. HECKEL, Member AIME, are Graduate Student in Materials Engineering, and Professor, Department of Metallurgical Engineering, respectively, Drexel Institute of Technology, Philadelphia, Pa. Manuscript submitted May 6. 1968. IMD MATHEMATICAL MODEL The three geometries analyzed are shown in Fig. 1. For each configuration a symmetry element is shown, across whose boundaries the mass transfer is zero. Mean composition, C, and the characteristic solute-rich phase half-thickness (or radius), 1/2, are the independent variables while the characteristic symmetry element half-thickness, L/2 (measured from solute-rich phase center to the matrix phase plane of zero mass transfer), is a dependent variable. The symmetry element for a planar interface accurately represents a real diffusion situation involving the stacking of symmetry elements of constant size. Because cylindrical and spherical symmetry elements of constant size cannot be stacked to fill space, the meaning of the dimension, L/2, for these situations may be considered in terms of the following approximations: and where NA is the number of parallel cylindrical elements per unit area on a surface normal to the cylinder axes and Nv is the number of spherical elements per unit volume. The model consists of a solute-rich phase matrix phase composite of limited mutual solubility. The concentrations at the interface are assumed constant with time; no assumption of local equilibrium at the interface is necessary except for the case where the

Jan 1, 1969

By M. David Monroe

Getting the best match between truck and haul road requires examining the cost effects of many factors. Most mines use a bottom line measure based on cost per ton of material moved. This measure focuses on the two components of truck haulage cost per ton: productivity (or performance) and operating cost. For specific tasks, productivity can be measured or predicted using either field measurement or modeling. Individual tasks can be combined to provide a larger scale, longer term net figure for total mine output. True cost is more difficult to capture. Factors are time- and task-oriented and can be influenced by a summation of factors over a truck's lifetime. For example, "allocated" costs, such as owning (depreciation) and some repair costs, are spread over long periods. Items such as fuel and tires can be tied more directly to certain tasks. This article focuses on the more direct, task-oriented factors that affect truck productivity and cost. Major factors The relationship of haul roads and trucks means that each must be examined separately to isolate the most important factors affecting performance and cost. There are many factors but the most important are:

Jan 1, 1992

By Neeraj Saxena, Madhu Huggahalli, Jerry Bednarski, Ken Grieshaber, David Stoffel

"The use of oxy-fuel burners in secondary aluminum melting applications offers several advantages over air-fuel burners including reduced fuel consumption, faster charge to tap times and lower NOx emissions. Their successful, safe and economical use in a furnace depends on several factors and considerations such as burner and flue placement, metal circulation, charge practices and the type of refractory used in the furnace.These factors required in the successful conversion of furnaces from air-fuel to oxy-fuel based burners are discussed in this paper. Critical parameters are identified and examined using computational fluid dynamics (CFD) simulations. Parameters are estimated via laboratory testing and validated through trials performed at commercial installations. Guidelines and a simplified approach to estimate a priori the economic impact of converting from air-fuel to oxy-fuel are presentedThe final products of this research are simplified and validated tools for modeling aluminum furnaces. These include improved heat and energy balance models and parameterized CFD solutions which provide rapid customization to individual furnace configurations. These tools provide field engineers with immediate and accurate predictions of performance, allowing for repeated precise scenario analyses."

Jan 1, 2001

By G. T. Lapidus, R. M. Luna-Sánchez

In the present study, a series of cyanidation experiments were performed on a bulk sulfide concentrate which contained silver in four distinct phases, to determine its extraction rate, varying the oxygen concentration. The results showed that three of the four phases were refractory, aguilarite (Ag,iSeS) being the only leachable phase, and that the effect of the oxidant concentration is minimal. Mathematical simulations were performed, adjusting only the Damkohler number to adequately fit the experimental data. This model, and the mechanism implied, was compared with that found for acanthite (Ag2S) in a previous study, and the differences between the two discussed.

Jan 1, 2005

In 1973, US Borax & Chemical Corp. began investing three days wages and about $20 in training materials in every new employee before having him report to his first job. The result? Accidents involving new employees in the past two years have dropped by more than half from the 1972 level. What made this success possible was safety training done with programmed instruction materials-which, incidentally, US Borax also uses for vocational training.

Jan 4, 1976

By K. Morikawa, K. Asano, J. Yoshitomi

The quality requirements for ladle shrouds have become stricter year by year to the pursuit of higher productivity and improved quality in the continuous casting of steel. The ladle shrouds must be sufficiently durable under severe conditions, such as operation without preheating and during several sequential castings. The consideration is that ceramic fibres, which have been applied in shrouds for thermal insulation during casting, could pose a risk to the worker's health. We realized materials for the ladle shrouds which show high strength and low elasticity. At the same time pursuing effective insulation, a coating which contains no fibres (Foaming Coat) has been developed, replacing the conventional one containing fibres. These materials are durable under conditions of repetitive use and consequently satisfy the customer's demands. The ladle shrouds which were improved in this way have achieved an excellent durable life in hot service of three times that of conventional ones. This paper reports the recent technological developments in ladle shrouds as well as their performance under hot operating conditions.

Jan 1, 2004

By Braulio Fernández, Gonzalo Montes-Atenas

The mechanisms taking place during the leaching of chalcopyrite when it is in contact with other sulphide minerals, particularly pyrite, is still a matter not fully solved. The GalvanoxTM process has been suggested as a technical solution to extract copper from chalcopyrite at commercial level inhibiting passivation phenomena widely reported in the field of hydrometallurgy. Although there are some rules of thumb to implement the process in fully flooded stirred conditions such as the optimum pyrite/chalcopyrite mass ratio should range between 2 and 4, among others; not many research studies have been focused on studying the effect of the surface contact area between chalcopyrite and pyrite to reach best copper extraction conditions. The aim of this research work is to determine the effect of the mass and surface area ratio between the minerals and the surface area of each of the mineral species effectively exposed to the leaching solution. Different particle size distributions of pure pyrite and chalcopyrite were contacted in a small column and subjected to leach tests using sulphuric acid in concentrations close those used in industrial leaching processes. The mass and surface area ratios which optimize the extraction of copper were obtained. It was found the best leaching conditions were attained when reducing the particle size distribution of pyrite regardless the particle size distribution of chalcopyrite. Further analysis concerning the impact of this conclusions on large scale operations is presented and discussed.

Jan 1, 2014

By M. S. Seehra, V. Suresh Babu, R. S. Pandurangi

Different mixtures of the three polymorphs of silica viz. quartz, cristobalite and tridymite are analyzed by x-ray diffraction (XRD) and their IR spectra are investigated by photoacoustic spectroscopy. It is observed that XRD provides a higher resolution to distinguish between the three polymorphs in a sample than IR spectroscopy. In the latter, a sharp band near 617 cm-1 is characteristic of both cristobalite and tridymite. A mine dust sample is quantitatively analyzed by XRD and it is shown to contain illite, quartz, kaolinite and calcite.

Jan 1, 1991

Official Program

Jan 8, 1950

By A. Pranowo, G. R. F. Alvear F., N. Aslin, M. S. Moats

"The toxicity of arsenic is well known and documented; however, the presence of arsenic in copper electrorefining anodes and electrolytes is critically necessary to produce high-quality cathode. Arsenic as well as antimony and bismuth concentrations vary relative to their concentration in the anode copper received from the smelter. The behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance are discussed. This will include the minimization and mitigation of problems associated with arsenic, antimony, and bismuth—including cathode contamination, floating slimes, scaling, and anode passivation.RÉSUMÉ La toxicité de l’arsenic est bien connue et documentée; toutefois, la présence d’arsenic dans les anodes de l’électroaffinage du cuivre et dans les électrolytes est d’une nécessité critique pour produire une cathode de grande qualité. Les concentrations en arsenic, ainsi qu’en antimoine et en bismuth varient selon leur concentration dans l’anode de cuivre reçue de la fonderie. Le comportement et les avantages de l’arsenic dans l’électroaffinage du cuivre et les effets indésirables de l’antimoine et du bismuth sur la qualité de la cathode et le rendement des cuves d’électrolyse sont discutés. On traite aussi de la minimisation et de l’atténuation des problèmes associés à l’arsenic, l’antimoine et le bismuth – incluant la contamination de la cathode, les schlamms flottants, l’entartage et la passivation de l’anode."

Jan 1, 2016

MINERALS BENEFICIATION DIVISION Established as a Division February 16, 1948 E. H. Crabtree, Jr, Chairman Donald W. Scott, Associate Chairman S D. Michaelson, Regional Vice-Chairman Will Mitchell, Jr., Regional Vice-Chairman William B Stephenson, Secretary-Treasurer Allen-Sherman-Hoff Pump Co 259 Lancaster Avenue Wynnewood, Pa. Raymond E. Byler, Past Chairman

Jan 1, 1952

By W. F. Guenther

The usual hand-operated drilling outfit consists of a 4-in. post-hole auger with 3/4,-in. pipe for drill stem, in 4-ft lengths, with a turning handle fitted to a top pipe T. The auxiliary tools are: a chisel-bit drill made from 3/4 or 7/8-in. tool steel welded to a 4-ft length of 3/4-in, pipe, so that the regular pipe string can be used; also a churn or "mule foot" made from 3-in. pipe, slotted on one side, belled to a 4-in. tempered cutting edge on the bottom, all welded to a 3/4-in. coupling by a yoke. Other tools required are pipe wrenches and cleanout tools made from old auto springs (Fig I). A 4 1/2 or 5-in. collar welded to a plate is often used to protect the mouth of the drill hole. In general the auger is used in the typical clay overburden and brown phosphate matrix, which is relatively soft. The churn or "mule foot1' is used in hard pan, lump phosphate or cherty ground. The drill is used for breaking flint, often found loose in the overburden. The drill with the chisel bit is used for trimming sides of the hole, sounding for lime bottom and breaking through hard lumps. Holes have been drilled to a depth of 80 ft, but the limit of efficient operation is about 50 ft. In deep holes it is necessary to unscrew the string in 20-ft lengths, to

Jan 1, 1948