Search Documents

Limnological processes are often overlooked when trying to assess the long-term water quality of pit lakes. It is essential to deal with these aspects, since they determine the geochemical and redox conditions around the submerged reactive rocks. Underground mining at East Sullivan (northwestern Quebec, Canada) stopped in 1966. Two adjacent stopes, 91 and 106 m deep, were left open to the surface, with roughly circular apertures of about 7700 and 18 000 m2. Water filling of the two glory holes went on over three decades and overflow began in 1999. Surface water pHs values were near neutrality as late as 1994 (6.3 - 7.0) but had become acidic by 1999 (2.6 - 3.5). Limnological processes were investigated in late-1999 and early-2000, with temperature measurements at 1 m intervals and sampling of the water columns before and after the late fall density inversions. A strong chemocline-thermocline was observed at 15 m. Above the chemocline, the water had low pH (3.2), no alkalinity, and low Na, Ca and sulfate. Below the chemocline, the concentrations of these parameters and the pH increased, with pH at 5.5 - 6. Consistent with the low pH values present in the upper 15 m, the concentrations of Al, Cd, Cu, and Zn were high near surface, and decreased below the chemocline. Dissolved oxygen concentrations as well as Eh decreased with increasing depth. Alkalinity integrated over the entire water column below the chemocline was at least six times larger than the acidity inferred from Fe2+ and Fe3+ concentrations. The temperature survey showed that seasonal density inversions do occur in the water column. The inversions do not involve the entire water body, since the surface to depth ratio is too small for a complete overturn. Oxygen from surface waters is carried to the bottom where it oxidises sulfides, until its depletion. Residual Fe2+, stable under anoxic conditions, is displaced upward by the next dense water incursion. It eventually reaches the thermocline, but only after many successive incursions. There, its oxidation to Fe3+ allows hydrolysis, which consumes dissolved and wall-rock alkalinity. It is only in 1999 that alkalinity was finally exhausted and that the pH shifts to acid values. The low pHs in the surface waters allow a build up of Fe3+ and Al3+, and desorption of metals from colloids. Buffering is assumed to be controlled by wall-rock oxyhydroxides in surface waters, and by carbonate minerals in the bottom waters. Because the seasonal overturns are far from being complete, the large amounts of alkalinity acquired from the wall-rock in the bottom waters cannot balance the acidity of near surface waters. Hence the surface water is acidic.

Jan 1, 2003

I would like to congratulate the authors on an interesting paper and, in particular, on their justification of the use of superposition in treating gas wells. They state, however, that no theory has previously been developed lor treating the variable rate drawdown case. In a paper published a few years ago by my colleagues and myself, a method is described which allows a constant rate drawdown curve to be derived for any well. regardless of real rate variations. This method has the great advantage that it is not necessary to make any assumptions regarding the form or uniformity of the reservoir, and the derivation suggested by the present authors is simply an idealized case of our more general treatment. In the light of several years' experience in the derivation of constant rate drawdown curves: I would like to point out that the method proposed by Odeh and Jones may lead to confusing answers, particularly if applied over an appreciable time interval. The reason is that, if pressures are measured when a well is flowing, non-linearities in plots like Figs. 1 and 2 can arise due to either (1) changes in the skin factor with time and/or flow rate, or (2) an inhomogeneous reservoir. Separation of these two effects is only possible if some of the pressures used in the analysis are measured when the well flow rate is 0 or, in other words. during brief shut-in periods. REFERENCES 1. Arthur, K. B.. Metunomski, Z. G. and Ruche, Ms "Intetet ct methode d'utilisa tion des mesures de pression [)our Petude des gisemonts" Revue de T'I.F.P. (Nov., 1962) XVII, 1299. 2. Thomere, R. and Arthur, K. R.: "Analysis of the Pressure Bet~avior of a Production Well Subject to Interterence and Its Application to Reservoir Models", Paper SPE 1189 presented at SPE :Amund Fall Mecting Ireld in Denwer, Colo. (Oct. 3-6, 1965).

Jan 1, 1966

By Shiro Ban-ya, John F. Elliott, John Chipman

The activity of carbon in Fe-C austenite at 1150°C has been determined for concentrations up to about 2.1 pct C using the equilibrium: C + COz = 2CO; equations have been derived expessing the activity as a function of carbon content on the basis of twelve mathematical models. Several of these represent the data satisfactorily. ACCURATE information on the thermodynamic properties of austenite in the binary system Fe-C is needed as a basis for studies of transformation and precipitation in steels of all sorts, alloy as well as plain carbon. The many attempts to approach this problem through statistical thermodynamics require sound and dependable experimental data in order to evaluate the several models which have been suggested. In this paper we are concerned with the experimental determination of the activity-composition relation in austenite at the temperature of its widest range of stability, approximately the eutectic temperature (1153°C). Accurate investigation of the activity of carbon in austenite may be said to have begun with the work of Dunwald and wagner.' A more detailed study was carried out by R. P. smith2 on the two equilibria: More recent work on these two equilibria has been reviewed by Chipman,3 who pointed out the experimental hazards associated with studies of Eq. [I]. Studies of this reaction involve rather small values of the ratio these are susceptible to errors due to traces of moisture in the apparatus according to the reaction: Ellis, Davidson, and Bodsworth4 evaluated K, for their experimental temperatures and used desiccants to control water vapor pressure. While they were able in this way to obtain consistent values for K1 it cannot be said that all of the uncertainties of the method have been overcome. Results by both methods reported by Schurmann, Schmidt, and wagener5 appear to be consistent except at very low carbon content. Reaction [2] was employed in the experimental work reported here. It is to be recognized, however, that it is not applicable to projected studies of certain alloy steel compositions involving stable oxide-formers.

Jan 1, 1970

By J. E. Dutrizac

A mineralogical study of a weak acid leach residue from the Clarksville zinc plant of Savage Zinc Inc. was carried out. The study focused on Pb and Cd as these elements most significantly impact on the environmentally acceptable disposal of the residue. The residue consists of major amounts of bassanite, zinc ferrite and various Zn-Pb-Fe-Cd silicate species. Also present are lesser quantities of PbSO4, sphalerite, Fe2O3 quartz, Mn-Pb-Fe oxides, SrS04, (Pb,Sr)SO4 iron gel-silica gel, jarosite and Ti oxide. The principal Cd carriers are the zinc ferrite, which contains up to 9.00% Cd and likely accounts for -45% of the total Cd content of the residue, and the various silicate species which contain up to 6.97% Cd and account for about 45 % of the total Cd. The sphalerite is a minor Cd carrier containing an average of 0.35 % Cd and accounting for -5 % of the total Cd; the other carriers contribute only trace amounts to the total Cd content. The major Pb carriers are PbS04, Pb-bearing silicates and Mn-Pb-Fe oxides. Minor proportions of the total 1.09% Pb content of the residue are carried by SrS04 and (pb,Sr)S04' Trace Ph carriers include the iron gel-silica gel, Fe-Zn-AI oxide and bassanite. The residue after the toxicity characteristic leaching procedure (TCLP) is mineralogically very similar to the initial weak acid leach residue; the amounts of calcium sulphate are approximately the same in the two products. The principal Cd and Pb carriers are also the same as those noted in the initial residue, except that some dissolution and reprecipitation of Pb-Sr sulphate takes place. That the residue fails the TCLP test is likely a consequence of the superficial dissolution of Pb and Cd from species such as PbS04 or Zn-Pb-Fe-Cd silicate.

Jan 1, 1995

By K. M. Rolls, F. W. Reuter, J. Wulff

The superconducting behavior and microstructural characteristics of a nominal Nb-40 wt pct Ti-0.239 wt pct O alloy were studied as a function of ther mo -mechanical processing treatment. Critical current density us applied transverse magnetic field was obtained for 0.010-in.-diam wires at 4.2°Kin steady fields 14 to 110 kG. Both optical metallogvaphy and transmission electron microscopy were used to delineate the micros tructures of the same wires. It wan found that a 1-hr 500°C precipitation heat treatment after cold drawing to final size led to the highest critical current density. Heat treatment at 600°C also led to a high critical current density, but the precipitate differs in kind and form from that at 500°C. The resistire critical field was also found to be sensitive to precipitation heat treatment since the effective composition of the superconducting phase changes. This is discussed in terms of the oxygen in interstitial solid solution. Two types of high-field superconducting wire are at present used in the construction of high-field superconducting solenoids. These types are solid-solution alloy wire such as Nb-Zr and Nb-Ti and composites of the brittle inter metallic compound Nb3Sn. The latter generally have a high super cur rent-carry ing capacity which is difficult to vary if properly made. The supercur rent- carry ing capacity of the former can be varied drastically and often predictably by suitable thermomechanical processing treatments. In general, the critical current density Jc of the solid-solution type of alloy is increased by cold work and by additions of interstitial elements along with aging heat treatments. The imperfections which result are be-iieved to be responsible for the observed increase in Jc. In 1962 Kneip and coworkers1 found that the critical faurrent density of Nb-Zr alloys could be increased by proper heat treatment preceded and followed by cold work. Betterton and coworkers2 using a Nb-25 at. pct Zr alloy found that small additions of oxygen or carbon enhanced the effect of this heat treatment. They suggested that the interstitials present aided precipitation in the alloy, leading to a filamentary structure with superior properties. If the precipitation heat treatment was omitted, interstitial additions had a negligible effect on Jc. wong3 showed that higher heat-treatment temperatures lowered Jc. Walker and co-workers,4 who studied microstructure (by transmission electron microscopy) as well as superconductivity, found that the Jc anisotropy introduced by cold rolling was itself affected by heat treatment. They were unable to clarify the relation between microstructure and critical current density, although evidence of precipitation was indicated. More recent investigation of Nb-Zr alloys,5,6 besides showing that structural defects and fiber ing due to cold work and precipitation serve to raise Jc, also elucidate important optically observable microstructural changes which occur upon precipitation. In these reports, coarsening of the microstructural features was found to decrease Jc. Vetrano and Boom,7 who studied Ti-20.7 at. pct Nb, found that Jc was increased to a maximum by a 415°C, 3-hr heat treatment following quenching from 800°C and cold working. Heat treatments can also affect the resistive critical field Hr. Final-size heat treatments of Nb-Zr wire can lower Hr drastically if gross phase decomposition occurs5'* or moderately if the effects of cold work are eliminated without changing significantly the composition of the phase of interest.3,5,6,8 The percentage of oxygen which can be added to Nb-Zr alloys to enhance Jc is limited by the difficulty of subsequent cold drawing. Since Nb-Ti and Ta-Ti alloys in contrast can tolerate appreciably higher percentages of oxygen, it was decided to investigate the superconducting behavior of various alloys in these systems. The present paper describes the results of adding oxygen to a nominal 40 wt pct Nb alloy as a function of thermomechanical treatment. I) EXPERIMENTAL PROCEDURE A small alloy ingot was prepared from high-purity niobium, iodide, crystal-bar titanium, and Nb2O5 powder by arc melting on a water-cooled copper hearth in a gettered argon atmosphere. The ingot was turned and remelted fourteen times to insure homogeneity. After final melting and rapid cooling, it was machined round to 0.415 in. diam, jacketed in stainless steel, and cold-swaged to 0.117 in. diam. The jacket was removed and swaging continued to 0.051 in. diam followed by wire drawing in carbide dies to 0.010 in. diam. Although it was intended that about 1500 ppm O (by weight) be added, inert gas fusion analysis indicated a 2390 ppm 0 content, apparently due to additional oxygen pickup in the arc furnace. Even so, the alloy was sufficiently ductile to be cold-worked to greater than 99.9 pct reduction

Jan 1, 1967

The patterns of occupational health pro- grammes in mining and metallurgy are discussed in relation to the impact of chemical and phy- sical hazards on the health of workers in these fields. Mining and metallurgy are quite unique in that their history and practice embrace virtually the total spectrum of occupational health problems and hazards as understood today. A panoramic concept of the possibilities would comprise the following fields: 1. The Pneumoconioses or Dust Diseases. 2. Physical stress due to exertion, and exposure to heat and humidity in deep mines. 3. The toxic effects of various metals in the mining of ore. The most obvious are lead, mercury, arsenic and manganese. 4. Diseases associated with mining. These include leptospirosis, ankylostomiasis and mycotic infections of the skin. 5. The Beat Diseases of coal miners working in narrow seams. 6. Illumination problems and miners nystagmus. 7. Geographical and climatic problems

Jan 1, 1975

By T Salles, G Duclaux, E R. Ramanaidou

In a continental environment, sediment mobilisation, dispersion and deposition are mainly controlled by mass gravity and streamflow processes. Alluvial sedimentary systems have an important economic value because of their capacity to host mineral resources. In the Hamersley Province, alluvial iron deposits (including the well-known detrital iron deposits and channel iron deposits) play an increasing role on the commodity market. Alluvial deposits exploration is challenging and generally involves geomorphologic and stratigraphic field studies, as well as expensive exploratory surface sampling and drilling. We applied a new surface processes modelling technique to investigate iron rich material, ie the erosion product of bedded iron formations -dispersion in the Hamersley Province. LECODE is a 3D-parallel surface processes forward modelling code designed to compute surface flow and solve erosion, transport and sedimentation on the geological time scale. The code offers new quantitative ways to better understand how sedimentary deposits develop in intra-continental and channel environments. Here we show that our integrated forward model is capable of opening a window to the construction of sedimentary architectures, including facies distribution, deposit thickness and development of heterogeneities such as mineral traps over the modelled domain. The model results represent 1 Ma of surface evolution and are validated through comparison to published paleovalleys map and known occurrences of iron ore deposits. This numerical modelling approach allows for the first time to track alluvial materials from source to sink through time, test existing geological models and faithfully reproduce the first order distribution of alluvial iron deposits in an area of interest. This work strongly suggests the presence of iron rich alluvial deposits reserves under cover, in unexplored detrital fans in the Fortescue Valley. This method, potentially coupled with sediment geochemistry and basin analyses studies, has the potential to maximise alluvial iron deposits exploration success, while reducing exploration cost and associated environmental impact.CITATION:Duclaux, G, Salles, T and Ramanaidou, E R, 2013. Alluvial iron deposits exploration using surface processes modelling - a case study in the Hamersley Province (Western Australia), in Proceedings Iron Ore 2013 , pp 75-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Khaled Morsy

This study presents a typical stress-strain model for coal material using the available in-situ and laboratory tests data conducted on coal. This model can be used as a basic coal model in finite element applications The effects of pillar width-to-height ratio and the confining pressure have been considered in this model. The extended Drucker-Prager model with mobilized friction angle was found to be very successful in simulating the proposed model.

Jan 1, 2001

By Douglas C. Fraser

A DIGHEM survey was flown in the Belford-Montcalm Township area of Ontario in November 1975. This 600-linemile survey resulted in the detection of 134 EM anomalies. The Montcalm Township copper-nickel discovery yielded a single-line anomaly having a conductance of 154 mhos. This anomaly was highly visible because (a) it had the highest conductance in the survey area, (b) it correlated with a 175-gamma thumbprint-shaped magnetic anomaly and (c) it was isolated from long conductive bands. The deposit is a copper-nickel pyrrhotite body which occurs in gabbro and strikes north-south, parallel to the flight lines. The DIGHEM survey was flown north-south, because the exploration program was primarily concerned with locating copper-zinc sulphides in the east-west-striking felsic volcanics. The flight line passed close to the deposit and yielded a 9-ppm anomaly on the chart record. The computer analysis showed that a deposit of exceptionally high conductance (154 mhos) caused the relatively weak (9 ppm) anomaly. The ground follow-up program of magnetics and EM led quickly to the discovery drill hole, which penetrated the orebody in September 1976. Subsequent geophysical surveys consisted of horizontal-loop EM, pulse EM, magnetic and induced polarization surveys over an area of about 8 claims. In addition, a detailed DIGHEM" airborne survey was flown at a line spacing of 100 m to evaluate the entire property of 620 claims. This detailed survey yielded EM conductor maps and contour maps of resistivity, magnetics and enhanced magnetics.

Jan 1, 1978

By Faustino G. Prado

In the, quest for an economical and environmentally friendly reclamation of metallurgical dusts generated during pyrometallurgical operations, our goal has been the separation and recovery of most of the components, as well as the complete recycle of all the reagents. Effluents have been avoided, within acceptable economic parameters. This presentation, which can be applied to a large spectrum of dusts and other residual-materials-, has focused on the dusts generated by the operation of Secondary Copper Smelters. Those dusts show a wide range of components, including zinc, lead-, copper, cadmium, tin, chlorine and-alkalies. Our present work deals with the use of ammonium salts in the separation and recovery of-the above mentioned elements in a marketable form. Most of the chemistry and techniques involved have teen already confirmed in commercial scale operations. Others have gone through pilot scale tests or bench scale tests. The recycle of reagents has also been- confirmed at the same operating levels. A preliminary evaluation indicates that the chosen route, in addition to a viable economy, offers a complete and safe reclamation within the most strict environmental regulations.

Jan 1, 1995

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

By H. A. Buehler

LOCATION THE Ozark region occupies a large part of the southern half, of Missouri, the northern portion of Arkansas and comparatively small areas in northeast Oklahoma, southwest Kansas, and southern Illinois. . It is a roughly elliptical plateau which has been deeply dissected by stream erosion, and which slopes imperceptibly into the prairie regions to the north, east, and west, but which terminates rather abruptly along the Arkansas River on the south and Tertiary lowland to the southeast. The-Boston Mountains extending for a distance of some 200 miles (321 -km.) along the Arkansas River rise to an elevation of 2000 ft. (609 m.), forming the most prominent topographic feature of the region. The so-called St. Francois Mountains in St. Francois, Madison, and adjoining counties in southeast Missouri, form a prominent but more restricted topographic feature, the highest point rising to an elevation of 1800 ft. (548 m.).. The remainder of the region is largely a plateau area varying from 800 to 1500 ft. (243 to 457 m.) in elevation. STRATIGRAPHY The region is underlain chiefly by sedimentary formations, which outcrop in roughly concentric bands around a comparatively restricted area of igneous rocks in the St. Francois Mountain district. Although located geographically near the eastern edge of the Ozarks, the St. Francois Mountains have apparently suffered the greatest orogenic movement and the lowest formations of the succession are exposed in their immediate vicinity. The various sedimentary formations of the region do not show any considerable metamorphism and have suffered little change since consolidation. With the exception of a few basic intrusions in Ste. Genevieve County and a pegmatite dike in Camden County, Missouri, there is no evidence of igneous-action, since the first sedimentary beds were deposited.

Jan 10, 1917

By W. M. Tuddenham, R. J. P. Lyon

In many areas surrounding the orebodies in mining districts rocks have been bleached and altered by the ore-forming solutions and have been oxidized during later weathering processes. A number of the rock-forming silic-ates have been broken down to clay, sericitic micas and chlorites have been developed, and pyrite may be found hundreds of feet outside the economic limits of the orebody. These halos of altered ground are prime targets used by geologists in many districts to delineate promising sites for drilling. Both in the field and in the laboratory it is often difficult to map these mineralogical changes in the halos in detail without numerous petrologic examinations. The secondary minerals are generally fine-grained, and since conversion of one mineral to another is often progressive, many alteration processes have not proceeded to completion (feldspars to clay to sericite mica). Qualitative detection of these minerals is difficult; quantitative determination is frequently impossible.

Jan 1, 1960

Jan 1, 1941

By Patrick Ph. D. Kennedy, Osvaldo A. Ph. D. Bascur

With the revolutionary progress in information and computer technologies, applying the latest information technologies in metallurgical complexes has become a serious challenge to both a major opportunity and a serious challenge to both management and technical teams. The emerging component and object technologies are changing the way everyone can beneficially use their computer and networks to add to their corporate bottom lines. Most mining and metallurgical plants use predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis and oil and lube analysis for critical equipment. Process control strategies are installed in several metallurgical sites. All process equipment and control strategies require maintenance from local personnel at the mine. Integrated use of existing and emerging technologies is making it possible to implement an overall process effectiveness control index. This index is based on key indices such as losses due to plant availability, performance efficiency and rate of quality. The availability of real time and process history to identify the most critical part of the processing system from mechanical integrity is highlighted. An emerging plant integration paradigm is described to simplify the implementation of business enterprise resources management and distributed plant management systems.

Jan 1, 1998

By Javier Rodriguez

Adaptive re-use of existing structures in urban environments has become very common due to lack of available space in our cities and requirements for increased structural capacity. Often, it involves retrofitting existing foundations to support increased loading. In such cases, Engineers face the need to review existing deep or shallow foundations for their true load carrying capacities in order to determine the required magnitude of retrofit work, if any. To accomplish this, the engineer must track down and cull through the existing construction documentation to determine what was actually constructed, complete an investigation to confirm these conclusions, possibly sample the foundation elements for strength properties, and on occasions complete non destructive or full scale load testing of indicator elements. This paper describes the typical procedure followed by the authors for design of retrofit schemes for existing buildings in the Washington DC metropolitan area. Three case histories are presented that illustrate various issues encountered during design.

Jan 1, 2006

By J. Parke Channing

These days of great industrial and social problems in America produce many suggested solutions and great changes. The practical engineer and employer of labor views these problems differently from the labor leader or the social reformer, but as never before he is sincerely interested in solving them in a way that will be just to all. The inevitable tendency of the day is toward "industrial betterment," " safety," '(industrial education," " efficiency," and the many other things which have become so familiar to progressive employers. There is no longer any question that these things are worth while from both the human and economic standpoints. They "pay" in dollars and cents. The very center of final success in improving conditions and increasing the efficiency of workingmen must be the spirit of fairness and a knowledge on the part of the employer of how to deal sympathetically and intelligently with his employees. Every progressive employer knows how greatly he desires foremen, superintendents, managers and others who possess these qualities. On the other hand, we are all familiar with serious mistakes made by young graduates of engineering schools who have had no opportunity to develop these qualities, and who have no real appreciation of the worth of the workers. Indeed, one wonders whether much ill-feeling, labor difficulties, and many strikes could not be avoided if such men had the right attitude. Is there any way of remedying this condition? If this particular difficulty can be solved, if these young engineers, many of whom are our coming leaders of industry, can be given the right perspective and the right understanding of these other problems in addition to fair, sympathetic methods of handling men, many of our other problems will be solved—not at once, but gradually and permanently, as these men make good and become influential in paths of industrial righteousness and industrial peace. Many progressive employers of to-day have enlarged their own perspective and realize the great importance of enlarging the perspective of those who shall follow them. How can it be done? For seven years a movement has been making

Jan 1, 1915

By F. L. Toy, C. E. Sims

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By Rixon K. L

Hargraves (1983) has reviewed the phenomenon of instantaneous outbursts of coal and gas with special attention to Australian occurrences. The purpose of this discussion is to highlight some problems and omissions in his review that reflect particularly on the authors' structural geological investigations of outburst-prone coal seams.It is surprising to find that much of the authors' reported work has either been glossed over or the results distorted by Hargraves (1983) and it is, therefore, important to clarify the contribution that structural analysis of coal seams can make.For many years it has been known that faults provided preferred loci for gas outbursts (for example, Briggs 1920-21) but the roie that faults played in outburstprone seams was unclear. The present authors reviewed the association of faults and outbursts drawing upon local investigations and the world-wide literature (Shepherd et aI., 1981), and discussed some wideranging aspects that result from the high coincidence of faults and outburst sites. Without repeating large segments of this article the authors will discuss four aspects of coal seam faulting and fracturing.

Jan 1, 1983

By M Gao

Six new IsaMills were installed for the George Fisher flowsheet in the Lead/Zinc Concentrator of Mount Isa Mines to produce a product P80 as fine as seven microns. The objective was better liberation of galena and sphalerite. The IsaMill commissioning was completed by the end of 1999. The six new IsaMills were running to the metallurgical specifications almost immediately after start-up. This paper reports the performance of the George Fisher IsaMills in the zinc circuits and some of the latest development in the IsaMill designs and maintenance during George Fisher commissioning.

Jan 1, 2000