Search Documents

By Carl A. Kuehn

At Carlin, Nevada, non-indigenous hydrocarbons were introduced as a bitumen phase which was mobilized due to burial under the Roberts Mountains allochthon. similarly, some indigenous organic matter was locally mobilized. Fluid inclusion and paragenetic data of veinlets formed during this hydrocarbon stage, combined with quantitative modelling or organic maturation, indicate that host rocks had evolved past dry gas conditions of around 1550 and l.l+0.2 Kb in the presence of CH4-saturated, highly saline brine by no later than early to middle Cretaceous time. All hydrocarbons present would have been rendered immobile under these catagenic conditions. Crosscutting relationships at several scales suggest that hydrocarbon mobility may have ceased prior to the intrusion of a series of dikes in the mine which have subsequently been altered and mineralized. Apart from subsequent oxidation, the current distribution and high maturity of carbon-rich zones were established prior to gold introduction. No Evidence has been found supporting proposed hydrocarbon "remobilization" during or after gold mineralization and alteration. The high density of the CH4-bearing fluid requires formation at high pressures (near 1 Kb) and precludes their formation as a result of the "cracking-off" of CH4 from organic matter during a thermal event associated with a shallow hydrothermal system. The density and composition of the fluid inclusions restricted to the early hydrocarbon-stages of the Carlin paragenesis are not unique to the sediment-hosted gold deposit environment of north-central Nevada. Similar inclusions are found in authigenic quartz crystals from Paleozoic carbonaceous shales in central Pennsylvania which have experienced normal metagenesis of indigenous organic matter due to deep burial.

Jan 1, 1987

By J. P. Stone

The Mining Regulatory Affairs review arrived in time for the May issue. The Managing Editor inadvertently buried it in one of his paper piles. Regulatory developments at the federal level involving the minerals industry solid waste disposal under the Resources Conservation and Recovery Act (RCRA) remained at the forefront of concern. The Environmental Protection Agency (EPA) received public comments on two major documents. One was a strawman draft rule covering wastes from mining and beneficiation. The other was a report to congress covering selected mineral processing wastes. The regulation of minerals industry waste management is moving forward on parallel paths. Mining and beneficiation waste is somewhat further advanced.

Jan 1, 1991

By Robert T. McKnight

"Traditional techniques for valuing resource projects companies have been primarily based on discounted cashflow methods (DCF) or by comparison to similar projects with an apparent market capitalization. Many resource projects are really forms of options to invest rather than a future cashflow stream. Employing the DCF method to value a resource project which is really an option to invest, can dramatically underestimate the real value of the project. The analytical tools required to evaluate options, while more complicated than the usual spreadsheets used for DCF, are becoming more easily available and usable by managers. This paper will discuss the background of options valuation and some of the tools which will make it easier for managers to estimate the value of projects and companies which have significant real option values.ResumeBob McKnight is a graduate of the University of British Columbia in Geological Engineering, supplemented by an MBA from Simon Fraser University. Following several years in the oil patch with Cities Service and Brascan, Bob returned to Vancouver in 1979 to work for Wright Engineers. He subsequently went on to work for Cassiar Mining, Getty Resources and Endeavour Financial before joining Pincock Allen & Holt Ltd. in 1998. His experience ranges from exploration to feasibility studies, financial evaluations of mining and oil & gas projects, due diligence, project finance, valuations and mergers and acquisitions. He has extensive international mining experience pertaining to such countries as Chile, Mexico, Uruguay, Thailand, Indonesia, Angola, Papua New Guinea, Kazakhstan.What are Options?Options have been around for centuries. They were familiar to Roman and Phoenician traders who were shipping cargoes from Mediterranean seaports. In the financial world, options are types of contracts that generally include the right, but not the obligation, to buy or sell a share, currency or commodity. The underlying commodity price or share price changes are assumed to be lognormally distributed. In this context, options are of two general types, ""call"" options and ""put"" options. Call options have the characteristic of having the right to buy a tradable commodity or currency at a predetermined price for a specified period of time. For the owner of call options, they become more valuable as the price of the underlying commodity increases. For the seller of call options, these options become an increasing liability as commodity prices rise, since there is the obligation to sell the commodity at a predetermined (perhaps lower-than-market) price. This characteristic of call options recently became high profile with the sharp rise in gold prices last year. The value of gold call options sold by certain producers increased their associated liabilities to the point where margin calls were made."

Jan 1, 2003

By D. N. Dietz

A method for determining average reservoir pressure is presented, which is simpler to apply than that devised by Matthews. Brons and Hazebroek. For bounded reservoirs, identical results are obtained if stabilized-flow conditions prevail. The present method yields inferior results in the transient state. The method can, with a slight modification, also be used for water-drive reservoirs. INTRODUCTION In the method proposed by Matthews, Brons and Haze-broek' for determining average reservoir pressure in a multi-well reservoir, the cumulative production (the production time of each well) enters twice: once when the buildup is plotted against In (t + t)/At to arrive at p*, and a second time when the correction, p*-p is determined with one of the several formulas for differently shaped drainage areas. Once a steady state has been attained, however, the previous production history should be immaterial. The same pressure distribution could have been arrived at after different cumulative productions of the individual wells. In principle, therefore, it should be possible to determine average pressures without referring to cumulative productions. In the following paragraphs an expression is presented for the difference between the pressure in a producing well and the average pressure of its drainage area. Then the build-up time needed to overcome this difference is indicated. CASE OF A CIRCULAR DRAINAGE AREA AND A CENTRAL WELL PRESSURE DISTRIBUTION BEFORE SHUT-IN The general differential equation of radial flow (see Muskat, Eq. 10.2) may be written In the steady state, the rate of production of the well is equal to the rate of expansion of the fluid contained in the the drainage area; thus

Jan 1, 1966

By Tapani Järvinen

Non-ferrous metals and metals in general are considered as being non-renewable natural resources. Metals are needed because of their excellent and irreplaceable properties. The consumption of metals, with the exception of carbon steel, is steadily growing by 1-3 % annually, and that of stainless steel as much as 3-6 %. This is a general trend, which is periodically disturbed by cyclical variations. In recent years so-called "New Economy" has become prominent in the public media and the market value of the traditional industry has been well below its real value and importance. Nevertheless, the modem society requires metals today and also in the future, and the companies using the most modern technology in a responsible way and innovative solutions not only in technology, but also in everything they do will survive. This paper describes the role of Europe as a producer of primary base metals and as a supplier of technologies in the base metals industry. It concentrates on the development and commercialization of technologies and project implementation in the metallurgical industry. As one example ofa European approach to these matters the paper presents Outokumpu's response to the future challenges in the base metals industry. Outokumpu Oyj is one of the leading metals and technology companies in the world of stainless steel, copper, zinc, and sales of technology in metals and minerals businesses. Outokumpu applies its knowledge of metals and processing to generate value for its customers and shareholder. Everything we do, we do in an economically, environmentally and socially responsible way.

Jan 1, 2003

By G. F. Trainor

The complex ore body at CNRL?s Horizon mine presents some unique challenges in managing ore and waste delivery. With 25m x 25m ore blocks shovels often take bucket loads from multiple blocks to fill one truck load. With CNRL monitoring 22 different qualities per material a precise calculation of the blended quality of ore on the back of each individual truck is essential to meet the daily blend requirements at the plant. Additionally, one of these qualities must be closely monitored and controlled at a singular level as delivery of certain grade and quantities can cause serious disruptions at the plant. The waste material also requires special handling and delivery for its use in dyke construction for tailings impoundment. Shale materials used in the construction contain high levels of saline that must be contained to prevent seepage into ground water. This paper will discuss how the use of Wenco?s survey-grade GNSS system on shovels, its dispatching algorithm, and fleet management applications give CNRL the ability and confidence to control and report on these three issues.

May 1, 2013

By Bill Paysse, Lyle Ruffle

My intention is to produce a video, pictorial, and oral presentation on utility blasting, primarily power pole holes and ditches. Included will be blasting for a take-off structure inside of Wanapum substation, jointly owned by BPA, PSE, and Seattle City Light, and blasting for 230kV steel tower foundations.

Jan 1, 2007

Shear strength testing of rock discontinuity surfaces has been undertaken at a considerable number of open pit gold mining operations in Western Australia, as part of geotechnical studies of pit wall stability. These mining operations are located in geological settings that are typified by highly weathered and/or chemically altered rocks that contain significant structural fabric in which accurate and representative measurement of shear strength is essential.Little of the published rock discontinuity shear test work and back-analysis of failures has been conducted on weathered discontinuity surfaces, at low normal stress levels which are comparable to Western Australian conditions. Available shear strength data are reviewed and the following aspects of shear strength testing are considered:ò the need for shear strength test work and the amount of testing required;ò review of laboratory testing methods and the quality of the results; ò presentation of the test results;ò discussion of the shear strength failure criteria; ò interpretation of the test results;ò summary of test results for a variety of rock types, degree of weathering and discontinuity surface conditions;ò a review of laboratory and field shear strength data to illustrate the amount of variability that can occur; andò a monitoring strategy is proposed to manage the uncertainty associated with discontinuity shear strength.

Jan 1, 1992

By W. Petruk

The silver-rich cobalt-nickel arsenides ores of the Cobalt area in Ontario, Canada were mined for silver from about 1904 to 1985. The ores contained about 8 oz to 100 oz Aglt and about 1 wt% Ni and 2 wt% Co. They were processed by gravitational techniques, screening and flotation to produce separate silver and Fe-Co-Ni arsenide concentrates. The silver concentrate was smelted, and in some cases the arsenide concentrate was sold to custom smelters which recovered silver and other metals. The ores display a wide variety of textures and contain many minor and trace elements. This paper presents an evaluation of mineral characteristics that have a bearing on extractive metallurgy and smelting of this type of ore.

Jan 1, 1993

By G. Begin

"The expansion undertaken at Selbaie in 1985 necessitated an adaptation and expansion of the equipment maintenance system. This paper relates briefly the stages of transformation of the maintenance administrative structures, work methods and tools. The maintenance in a mechanized mine requires an expenditure level in the order of 20% of the total operating cost of the enterprise. Thus, the maintenance organization was modified to apply more computerized planning and follow-up, and the role of preventative maintenance was further advanced.IntroductionAs far as maintenance is concerned at Selbaie, the scenario described herein is a resume of the current situation. Although positive results have been obtained, this outline is in no way a detailed account of a fail-proof maintenance system.Once zone A-I was put into production, the expansion the mine experienced in 1985 had a direct impact on the equipment maintenance system. As centralized as it was in the beginning, the system is now partially decentralized.The over-all changes to the maintenance department demonstrate the flexibility required by organizations in new situations. In spite of the exceptional results obtained before the expansion, it became evident that both the maintenance and production sectors would have to be combined. In doing so, a more appropriate coordination of maintenance work could be obtained and the maintenance staff would obtain a more detailed knowledge of the equipment in each sector. In addition, by keeping the general and specialized departments centralized, it was possible to offset the negative effect s of a decentralized system, namely too much manpower."

Jan 1, 1990

By N. B. Gray, R. V. Culver, W. S. Boundy, N. W. Stump

The kinetics of sulfation of single crystals of lead sulfide to lead sulfate have been studied between 969" and 1073°K in gas atmospheres of known composition using a thermobalance technique. The data are described by an equation derived on the basis that diffusion outward through the Product layer is the major controlling step. The rate of sulfation is linearly related to the logarithm of the sulfur trioxide partial DESPITE its industrial significance the oxidation of lead sulfide has received limited attention. The oxidation reactions have been studied using beds, briquettes, single crystals, or thin films of lead sulfide. Lead oxide and lead sulfate (PbSO,) were formed when Mclntoshl and Gardner2 roasted beds of galena pressure and the temperature coefficient of reaction is 40 ± 5 kcal per g mole. Gold marker experiments show that the sulfate layer grows by outward movement of ions through the sulfate layer. Initially the PbSO, adheres to the PbS but later forms an irnpewious spheroidal envelope; PbS vaporizes and pb2' ions diffuse through the envelope to react at the external surface. in air at temperatures up to 800°C. In a more extensive investigation, Tchizhykov3 obtained Pb, PbO, and PbS04 in accordance with Eqs. [1] to [4], when a bed of -200 mesh galena was oxidized in O2-N2 mixtures at 700° to 900°C.

Jan 1, 1968

Blastserve, ISEE’s Listserve is being replaced by our new Blasters Forum-online, an exclusive member benefit. Our goal is to provide an ISEE forum for you to network with your peers and exchange technical information and get answers to your technical questions. This forum is unique in the fact that only ISEE members are permitted to review or post on the site. Over time you will be able review the discussion history and use the archived discussion as a valuable resource for trends in the industry. The following are a sample of the discussions that too place recently on Blastserve

Jan 1, 2013

Government geoscience may be categorised by objective under three headings: Applied Research for Geoscientific Framework Studies, Resource Inventory, and Technical Advice. In Queensland, the Department of Resource Industries is active in all three categories. Under the program-based management system adopted in 1987, three Programs, namely, Geological Survey, Mineral Resources Development, and Energy Resources Development and Utilisation, have geoscience responsibilities.Prime responsibility for geoscience resides with the Geological Survey Program, which provides a geoscientific framework for mineral and energy exploration and the development of the State. Simply stated, the Program goal is to provide geological information when and where it is required. Geological Survey work also encompasses aspects of resource inventory and technical advice, complementing the work of the other two Programs. This role has a 122 year long tradition, for geoscientists of the Geological Survey have been engaged in investigations designed to facilitate the identification and utilisation of the mineral, water and energy resources of Queensland since 1868.

Jan 1, 1990

By Edward Estabrook

THIS paper gives a brief account of the geologic and production problems encountered in the Grass Creek oil field, the methods used in their solution, and the beneficial results obtained from the work. The author wishes to acknowledge the assistance received from J. H. Pearson and Miss Ninettta A. Davis in the collection of the data and the preparation of the cross-sections. Permission for its publication was given by the officials of the Midwest Refining Co. and the Ohio Oil Co. The Grass Creek oil field is located in Ts. 98-99 W., R. 46 N., Hot Springs County, Wyo. The productive area includes about 2 1/2 mi. (4 km.) on the apex of a great anticlinal fold occupying more than 150 sq. mi. Fig. 1 shows the structural contours of the field. Oil was dicovered in the field in June, 1914; development proceeded rapidly and production rose to a maximum in 1918. The marketed production has been approximately as follows: BARRELS BARRELS 1915 94,073.5 1918 2,946,774.27 1916 1,404,183.97 1919 2,000,584.84 1917 2,780,697.51 1920 1,485,080.94 About 350 wells, 800 to 1500 ft. (243 to 457 m.) deep have been drilled to reach the upper oil sands; two companies, the Ohio Oil Co. and the Midwest Refining Co., operate the entire field.

Jan 2, 1922

By John A. Johnson

Tests ere conducted at the Mount Weather testing adit of the 57 Bureau of Mines on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. Equipment Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is mace of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.

Jan 1, 1939

In recent decades the awareness of environmental issues by the general public has developed at an accelerat- ing rate. This is the result of a number of factors including more scientific knowledge of environments and of the impacts of modern society upon them, higher levels of education, the opportunity for people to travel more, and the success of the various communication media in bringing in- formation to the communities of the world about such environmental crises or threats as the smogs of Los Angeles and London, the Torrey Canyon and Santa Barbara oilspills, Minamata disease in Japan, the spread of the Crown of Thorns starfish, the disposal of toxic industrial wastes into the Upper Rhine, the discovery of high mercury and zinc contents in marine foods in southern Australian waters, and the proposal to mine limestone at Precipitous Bluff in Tasmania.

Jan 1, 1975

By Qi Wang, Zengzhu Kang, Jianguo Liu, Guanglei Liu

"Due to the increase of automotive vehicles, available parking spaces become a new type of limited resource in central cities of China, especially in those old districts without visionary urban planning. Additional mechanical parking in underground space is an efficient solution to provide parking spaces under the situation where the urban space is constrained. Shichahai district is an old protected zone in Beijing which is close to the Forbidden City and there are many Hutong (alleyway) and Quadrangles (courtyard house). No spaces are available for car parking on the ground and all vehicles are parking in Hutong without order currently. The local government plan to do renovation work for this district and improve the residential environment. Several innovative solutions are studied including parking in deep shafts, parking under existing buildings by under-pinned method, parking under buildings by covered excavation method, parking under roads built together with utility tunnel etc. 5000 difference types underground parking spaces are planned to be constructed in the following three years. Project examples are also introduced in this paper. INTRODUCTIONCar parking resources are very limited in central cities, especially in old districts without planning for increasing automotive vehicle volume. Traffic get worse when cars park on the side of the roads or move slowly to find parking spaces. Investigation shows the normal (parking space/ automotive vehicle volume) ratio is about 1.2 in most big cities such as New York, Tokyo and Hong Kong, while this ratio is only 0.5 in Beijing. One solution is to move cars out of central cities. But there are still huge parking requirements for the citizens living in central cities. Shichahai district is an historic protected zone in Beijing which is close to the Forbidden City and there are many Hutong and Quadrangles (refer to Figure 1 for project location). No spaces are available for car parking on ground and all vehicles are parked in Hutong without order currently. The local government had a plan to do renovation work of this district and improve the residence environment. 5000 different types of underground parking spaces are planned to be constructed in the following three years. One project designed and to be constructed by Zhongyan Technology will be introduced in this paper. Other innovative solutions will be introduced briefly as well."

Jan 1, 2017

By B J. Kennedy, G W. Sengstock

During the last two decades, many advances have been made in open cut coal mining technology as new mines have come on stream and old mines have faced increasingly difficult mining and operational conditions. The need for close control of operating costs has necessitated consideration of modified excavation methods.

Jan 1, 1995

By Dunlop GA

Pilot Plant confirmatory testing of the treatment route developed in the Metallurgical Laboratory is an essential factor in the development of complex ore bodies. Objectives should be well defined to permit the efficient planning and cost effective operation of the pilot plant project. The primary objective for the pilot plant should be to confirm the viability of the developed flowsheet on a continuous basis, examining only major variables such as ore types, quantum changes in grind, comparison between bulk and sequential flotation circuits, use of flotation columns, evaluation of autogenous grinding and production of samples of concentrates for market evaluation. Secondary objectives may include the collection of engineering design data and the production of a comprehensive report to Bankable Document standards to provide technical support for capital financing. The complexity of the ore body and the scale of the final operating project together with the pilot plant objectives will determine the extent of the pilot plant operations. The level of expenditure associated with a pilot plant can vary, in total cost and as a percentage of the total development capital investment required to take the prospect from exploration to a producing mine. Factors contributing to expenditure are discussed. Associated with cost considerations is the level of confidence mining company investors can have that their capital investment will return dividends.

Jan 1, 1990

By C. C. Herrick

The vapor pressure of indium has been measured by the torque-effusion technique, as a function of temperature between 1102o and 1422oK. For liquid indium, the vapor pressure (in atmospheres) can be represented by the equation -R In P = 5.782 x104/T - 25.29from 1000o to 1422oK. Extrapolation yields a calculated normal boiling point of 2329°K and a heat of vaporization at 298 oK of 58.09 kcal per mole by the third-law method and of 58.39 kcal per mole by the second-law method. Calculations indicate that the free-energy functions of Hultgren are to be preferred to those of Guruich. BECAUSE of the potential uses of liquid metals, it is important that convenient experimental methods be developed which will lead to a sufficient body of thermodynamic data so that reasonable estimates of properties of liquid metals can be made. Indium is particularly well-suited to investigation, since it remains liquid over a long temperature interval, it alloys readily, suitable containers for it are easily procured, and relatively few investigations of its thermodynamic properties in the region above 1000°K have been made. PREVIOUS RESEARCH The first determination of the vapor pressure of indium was made by Anderson,' using the Knudsen method and silica-lines stainless-steel cells. Kohlmeyer and spandau2 determined the normal boiling point, and a mass-spectroscopic investigation has been made by Lyubimov and Lyubitov.3 (Unfortunately, only an equation representing the data of the latter investigators has been available to us.) Hultgren et al.4 and Gurvich5 have published discordant tables of the free-energy functions for indium. EXPERIMENTAL METHOD The torsion-effusion principle has been described amply in the literature.8,7 With this method, one observes the angular deflection induced by effusion of vapor from a multihole effusion cell which is suspended from a filament producing a small rotational restoring force. The pressure within the effusion cell can be computed from the relation ziaifiai where k is the torsion constant of the filament, 6 is the observed angular deflection, and ai, fi, and qi are the area, force factor, and moment arm of the ith effusion orifice. The force factor f is analogous to the Clausing factor,' and corrects for the reduction in effusive force attributable to the finite geometry of the effusion orifice. Schultz and Searcy' have tabulated the force factors for various tube geometries. EXPERIMENTAL APPARATUS The physical arrangement employed in this study is shown in Fig. 1. The furnace elements are six Globar heat rods with 15-in. hot zones. Temperature is maintained to * 1°K by a Beck mechanism driving two 26-amp Powerstats in parallel. A Pt (Pt, Rh 10 pct) thermocouple serves as the sensing element. Four inner tubes act as vibration isolators; the air pressure required for maximum isolation was determined empirically, and is maintained by a solenoid valve. The tungsten fiber, 9 by 0.002 in., is joined to an 0.008-in. tungsten wire or graphite rod via a machined lightweight chuck.

Jan 1, 1964