Search Documents

By M. Ataka

Magnesium alloys are not easy to plastically deform at room temperature and may suffer from edge cracking at high reductions, especially during sheet rolling. In this study, the authors attempted to improve the rollability by the low-temperature hot rolling method, in which the rolling temperature range is lower than that of hot rolling, and also by the edge-heating method, which locally heats sheet edges.

Jan 1, 2006

By Smith T. N, Wild M. B, Elliot B. J

The process of flash smelting of nickel sulphide ores, as practised at the Kalgoorlie Nickel Smelter, is described. The critical variables in the operation of this process are identified. The design of a pilot-scale, turbulent-jet flash reactor which models the essential features of the industrial smelter is described. A report of its operation and application to an investigation of the ignition of particles of sulphide species is given.

Jan 1, 1991

By Y. Q. Qui

In the bauxite flotation process for desilication, the middling treatment mode is the important factor to raise the flotation recovery of the preparation concentrate. The middling treatment mode mainly depends on A/S and the size composition. However, similar ratio of A/S should not be the single factor of re-dressing, size composition plays an important role also. Re-dressing the middling mixed with the tailings of concentrated to the rough ground for desilication and the concentrate of scavenged to the fine ground for desilication to raise the recovery of 5.83%, when compared two flow sheet schemes.

Jan 1, 2014

By Dara P. Antia, Morris Cohen, Frank S. Gardner

THERE is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a specimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallographic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X-ray exposure and film-development conditions, a standard reference line is superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduct ion through multilayer (wall and floor of airway consist of several layers of material and rock) and two-surface (dry and wet surfaces) airway wall and airway floor with convective heat and moisture transfer between their surfaces and mine air with time dependent changes of temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for calculation of the surface temperature of any type of surface of airway wall/floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. These solutions are illustrated for the case of general harmonic course of air temperature and humidity. Balance of heat and moisture transfer between surfaces of airway wall and floor and mine air is solved by an iterative method in the partial sections of airway. The temperature and the humidity of mine air on the outlet of each partial section of airway at given time are its resolutions and they are the input data for following partial section. By this way it is possible to solve complicated dynamic changes of mine air temperature and humidity in an air way system by relatively simple mathematical apparat.

Jan 1, 1991

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal. Investigations are in progress to develop a computer based scheduling tool capable of simulating the complex operating environment. A review of computer scheduling packages currently available within the State Electricity Commission of Victoria has found limitations making most unsuitable for the task. The type of package found to be most suited is a knowledge based system ('Expert System')capable of operating within a set of rules defined by the user. Work is proceeding on the development of a knowledge base to test the effectiveness of Personal Computer based `Expert Systems'.

Jan 1, 1989

An active list of permissible explosives was published in December 1936 as part of Bureau of Mines Report of Investigations 3324, under the title "Active List of Permissible Explosives and Blasting Devices Approved Prior to July 31, 1,936." This list included 170 brand names. Changes in the list that have been authorized to June 30, 1937 placed 35 additional brands of permissible explosives on the active permissible list as a result of tests, changes in brand names, or transfer from the inactive list. Ten permissible explosives were transferred from the active to the inactive list. The present list contains 196 brand names, one explosive having been placed on the list subsequent to June 30, 1937. The brand names of the permissible explosives placed on the active list are as follows: [ ]

Jan 1, 1937

By Keith E. Dyas, John Nelson, Ronald T. Johnson

GENERAL DESCRIPTION The Bruce mine of Cyprus Mines Corp. is located in Bagdad, AZ. The mining method used is open cut-and-fill. Of the annual production of 81 647 t (90,000 st), approximately 83% is taken from load-haul-dump (LHD) stopes and the balance from slusher stopes. All ore is produced from the area between the 1250 level and the 2300 level. The average travel time from the shaft pocket to the stope is approximately 5 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip The Bruce ore body occurs in quartz-sericite schist with Dick rhyolite on the footwall and andesite on the hanging wall. Diabase dikes are found in the hanging wall; there is also a dike coming off the footwall and crosscutting the ore body. All of the rock types are of the Precambrian Yavapai series and have been subjected to regional metamorphism. A composite of the ore body is given in Fig. 1. The deposit is of massive sulfides occurring as a steeply dipping replacement body. On the upper levels the ore is veinlike with widths from 0.6 to 4.6 m (2 to 15 ft), dipping at 1.4 to 1.5 rad (80° to 85°). On the lower levels the ore is dipping from I to 1.2 rad (60° to 70°) with widths from 3 to 16.8 m (10 to 55 ft). The strike length varies between 107 to 183 m (350 to 600 ft). The rhyolite footwall generally has a knife-edge contact with the massive sulfides. The exceptions to this are the upper levels where there is a 1.5 to 3 m (5 to 10 ft) band of silicified sericite schist between the sulfides and the rhyolite. In the southern part of the ore body the hanging wall is tuffaceous andesite and andesite. In this area the contact is generally sharp and easy to follow. However, to the north there is a large chlorite schist zone that crosscuts the bedding and comes in contact with the massive sulfides. This is apparently due to hydrothermal alteration of the andesite. The chlorite schist is highly mineralized with chalcopyrite and pyrite and quite often forms economic pockets of ore. In the massive sulfides the chief ore minerals are sphalerite and chalcopyrite. Pyrite is the predominant sulfide with considerable pyrrhotite throughout. Bright arsenopyrite ouhedrons in fine grain massive sulfides are quite common. Occasionally small amounts of galena are seen, usually near the foot or hanging wall contacts. On rare occasions tennanite is associated with massive arsenopyrite. Minor amounts of quartz, calcite, and un¬replaced remnants of sericite schist occur, but essentially pyrite is the gangue in which the ore minerals occur. The ore values are in excess of 3.5% copper and 12.5% zinc with some silver and rare gold as byproducts. Ground Conditions The massive sulfides are generally self-supporting. One exception is in the 1850 stope where the ore body is 9 to 11 m (30 to 55 ft) wide and 152 m (500 ft) long. There are flat to shallow dipping slips and seams in the ore, creating extremely blocky ground. For support, old 25.4-mm (1-in.) hoist ropes were installed tensioned to 27 t (30 st), and then cement grouted over the entire length in longholes [14 to 15 in (40 to 50 ft) in length) drilled on 3-m (10-ft) centers from the level above. This has tied the formation together very successfully and virtually eliminated the blocky ground condition. Both the hanging wall and footwall are quite shaley in some areas. Reasons for Adopting Trackless Open Cut-and-Fill Methods First, any method other than open cut-and-fill would have caused too much dilution. The use of rubber-tired mining equipment in the pro¬duction stopes requires a footwall ramp. The inclines in ore will be mined out, so this ramp in the footwall will provide access to and from the stopes (Fig. 2). This incline is very expensive, but necessary to convert existing stopes to LHD mining. 'The final cost of ore mined by the LHD machines has not been determined. As of 1972, tons per manshift in the 2150 stope-the only one to complete a full cut-had increased from 7.58 t (8.36 st) to 12.83 t (14.14

Jan 1, 1982

By M Gerards, M Steinberg, T Graham

The quality and quantity of Australia’s secondary deposits, which include tailings streams and tailings dams, are higher than most countries’ primary deposits. In addition, these secondary deposits have already been mined and processed, meaning that the recovery of high-grade product requires low capital and operating costs.The most widely used process for the recovery of these valuable fine and ultra-fine hematite iron particles is the wet high-intensity magnetic separation technique, originally developed by Dr Jones over 55 years ago. Many of the original machines are still working today.The aim of this paper is to demonstrate the capabilities in terms of grade and yield of using sophisticated magnetic separation modules. All results and figures are obtained from test work and design and engineering work with material from the Pilbara. In addition, consideration is given to dewatering of iron ore product and tailings.Two types of tailings have been identified for processing. Firstly, tailings that have already been deposited in a tailings storage facility, and secondly, live tailings streams from an existing wet iron ore beneficiation plant. In both cases, the technical and practical results are shown along with relevant flow sheets and plant layouts. Finally, this paper highlights the total predicted power and water consumption, capital requirements and projected operating expenses.The results show that the operating costs are significantly lower than the mining and processing operations that are required for an equivalent amount of iron ore. The recovery of iron depends on various factors but is within the 30–50 per cent range at an equivalent grade to the mainstream product. Another significant benefit is that the magnetic separation process is water positive, meaning that water is released rather than added in the process.The processing of the Pilbara’s secondary deposits will therefore result in an overall reduction in operating costs, an increase in product yield from a plant, extend the life-of-mine and offer environmental benefits by reducing the tailings footprint and water usage.The quality and quantity of Australia’s secondary iron ore deposits and tailings are such that many other countries would judge these as equivalent to primary deposits. Furthermore, these tailings are already mined, available and liberated to such an extent that the recovery of a valuable product is highly economical in terms of capital expenses and operating expenses.CITATION:Steinberg, M, Graham, T and Gerards, M, 2015. Recovery of iron ore fines and ultrafines from tailings by using wet high-intensity magnetic separation – JONES WHIMS, in Proceedings Iron Ore 2015, pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Jerry T. Shelby

Surface and underground mining operations require equipment with high power output ratings. Haul trucks, loaders, dozers, and other equipment need increasing horse-power to meet production demands. To get more horsepower out of the engines driving the equipment, most manufacturers use turbocharging. Detroit Diesel puts the number at about 90% turbocharged, while Caterpillar estimates 75% to 80% of all its equipment is turbocharged. Turbocharging increases the power output and overall engine efficiency. But it presents some maintenance and operational problems that were not factors when only naturally aspirated engines (nonturbocharged) dominated the scene. A turbocharger is an exhaust-driven air compressor. Using the waste energy in the engine exhaust, a turbine wheel is driven. This wheel is connected by a common shaft to a compressor wheel. The shaft is supported by two plain bearings, or bushings. As the turbine wheel is rotated, the compressor wheel continually compresses the intake air to the cylinders. Compressing the intake air means that more air can be put into the cylinder to burn more fuel. The more fuel the engine can completely burn or combust, the more horsepower the engine can produce. Even though the turbocharger is a relatively simple device, it is a sensitive engine component. It requires special consideration at engine start-up and shutdown. Being freewheeling and exhaust driven, turbochargers can experience temperatures of 540°C 1000°F) and rotational speeds of more than 100,000 rpm. Due to those temperatures and speeds, lubrication is critical to the operation and life of a turbocharger. The turbo is located high on the engine, with the oil supply running through an external line from the sump. The recommended practice is to start the engine and allow it to idle for a few minutes before any revving or loading. This allows the oil to reach the turbo and properly lubricate the bearings before high rotational speeds are seen. Turbo oil supply lines can be as long as 1.5 m (5 ft). Depending on ambient temperatures and oil viscosity, it can take as long as 30 seconds for oil to reach the spinning turbo. However, as little as five seconds without oil can damage the turbo's bearings, reducing its life and overall efficiency. Lubrication problems seen at shut-down can also significantly affect turbo life and efficiency. Manufacturers recommend an idling period of five to seven minutes before engine shutdown. This allows the turbo to slow down and cool off somewhat to help prevent oil coking and bearing damage. When the engine stops, so does the oil supply. There is very little oil left on the bearing surfaces and in the turbo oil supply passages. The immediate heat transfer from the turbine wheel to shaft, bearings, and turbo body literally cooks what is left. This high heat without oil flow can cause bearing deformation by actually melting some of the bearing material. The rapid oil oxidation and coking will restrict oil passages, damage bearings and shaft. Besides heat soaking, there is another problem. If the turbo is spinning at high speeds when the engine is shutdown, the turbo must spin-down to a stop without oil flow. With the large size of turbos used on mining equipment, this spindown time without oil can be for as long as 10 to 20 seconds. Fortunately, lack of lubrication at start-up and shutdown and the subsequent bearing damage can be prevented by oil injection devices. These devices hold a reservoir of engine oil. The oil is injected to the turbocharger bearings immediately on start-up and for several minutes after shutdown. Oil injection devices are spring loaded, hydraulic accumulators. They are actuated at start-up by a solenoid wired to the starter motor. Engine oil pressure charges the accumulator during normal operation. Upon shut-down and loss of oil pressure, the device provides oil to the turbo for about two or three minutes. With an oil injection device, the engine can be started and immediately driven without fear of turbo damage. Also, an abrupt shutdown will not damage the turbocharger since the device will continue to lubricate for two or three minutes. A word of caution. Be sure the oil injection device provides positive oil displacement (pressurized oil flow). Do not use a gravity-flow device. Unless it is a true accumulator, the device could starve the turbo for oil on start-up, Ask for start-up and shut-down pressures and delivery times before considering installation. Keep the oil clean, and follow the manufacturer's recommended oil change intervals. These intervals are usually shorter than with naturally aspirated engines. Use oil with a CD rating designed for diesel applications. A multiviscosity oil is preferable. Use a synthetic engine oil, such as Mobil's Delvac 1, Gulf's Super Duty II, or Chevron's Sub-zero Fluid. Synthetics have much better flow properties at low temperatures. They also have greater oxidation stability (they can take the high heat of turbo-bearing lubrication. And they produce fewer deposits because they are more thermally stable. But synthetic oils do cost more - two or three times more. One additional point - maintain the air intake system. Since all mining is usually in a dusty environment, air filters should be changed regularly and intake systems should be checked for leaks. All intake air passes through the turbo. Any dirt or abrasives entering the turbo will damage the unit and shorten its life. While mining is a heavy duty business with severe operating conditions, you can get the life from your turbocharger that you expect by following a few simple steps: • equip the turbo with an oil-injection device to provide lubrication on start-up and shutdown; • change the oil and filters regularly; and • use the proper oil-synthetic, if possible.

Jan 3, 1987

By J. W. Mahar, E. J. Cording, F. L. Gau

INTRODUCTION The Washington, D.C. rapid transit system (METRO) when completed will consist of 98 miles of double track rail. Fifteen miles will be tunneled in rock and 12 large underground rock chambers will be constructed at station locations. The University of Illinois is under contract to Metro to provide observations and instrumentation services in the initial phase of construction. The work is coordinated through DeLeuw, Cather & Co., the General Engineering Consultant to Metro. The program is designed to monitor construction conditions as well as to provide information useful for the design of future rock tunnels and rock chambers in the Metro system. This paper presents the results of observations in the rock tunnels constructed to date. Most of the observations are in a 5000-ft-long, 30-ft-wide, double track tunnel in downtown Washington, D.C. Observations were also made in single track tunnels, shafts, enlargement areas, and pilot tunnels, and are being made in a large rock chamber 700 ft long, 76 ft wide, and constructed at shallow depth in a schistose gneiss. One of the major objectives of the observational program was to determine the orientation and character of joints and shear zones and to evaluate their effect on support requirements for various tunnel orientations and configurations. The consistency of geologic features throughout the Washington area has made the results of the initial study applicable to evaluation of support requirements on future tunnel contracts. The first section of this paper summarizes the geologic conditions in the tunnel and their effect on overbreak and rock movement.

Jan 1, 1997

By D. Torrey

Considering the two great interests of to-day, in iron upon the one hand and steel upon the other, and recognizing with measurable distinctness the peculiar fitness of each for special services to which they are applied, the proposition to unite the two metals in combination, to bring into simultaneous use the peculiar advantages which each offers, has great attractions. The limited success which has been attained by trying to bring about such combinations of the two metals through the use of fluxes in welding, has led to the general adoption of the opinion that an effective union of the two metals is impracticable, or to the view that if practicable it would have but limited commercial value. Such opinions are, I think, premature and erroneous, and having gained some knowledge of the character and value of the "Wheeler process" for welding iron and steel without the use of fluxes, I submit the following observations and opinions of the matter for your information, with the hope of eliciting such a discussion of the subject as it may require. The principle of the invention is to bring the two metals simultaneously to a welding heat in one pile, and then to manipulate it.

Jan 1, 1879

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

Background: The National Institute for Occupational Safety and Health (NIOSH) recently investigated ignition incidents resulting from drilling holes into sealed and filled plow frame sections. A farmer and farm worker were seriously burned in two separate incidents that occurred in the same county in New York under similar conditions. They had just penetrated sealed sections of their plow frames with electric drills when a roar of escaping gas at high pressure was heard, and the victims were thrown back by the gas jet and engulfed in flames. The flames were quickly extinguished ,but the victims suffered burns. NIOSH experts were asked to help find the cause of these hazardous incidents.

Jun 1, 1998

By Sherwin F. Kelly

With the progressive exhaustion of ore deposits easily discovered by surface prospecting, the attention of scientists is being turned more and more to the employment of mechanical means for the location of ore bodies whose outcrops are not visible. The dip needle, the Eotvos Torsion balance, and various methods of electrical prospecting are illustrative of the modem tendency. Interest in the possibility of applying electricity to the solution of many of the prospector's problems dates much farther back than is usually realized. The first person to notice an abnormal intensity of electrical activity in the region of certain ore bodies was an Englishman, R. W. Fox, who experimented on the Cornwall copper and tin veins about 1830. Dr. Barus, in the United States, carried the early experiments a step further in his work on the deposits of Eureka, Nevada, about 1880. He made the very definite suggestion that the phenomena noticed would be of material aid to the prospector. Not until Professor Schlumberger, of the Ecole des Mines, Paris, took up the matter, shortly before the war, was any definite effort made to put electrical prospecting on a commercial basis. His work resulted in the establishment of sound principles and practicable field technique, for two distinct methods of prospecting.

Jan 1, 1924

By Zhu Yangge, Hu Xiaoxing, Feng Qiming, Zhang Guofan, Zhang Xingrong

"During the flotation process of ilmenite and titanaugite with fatty acid as collector, unavoidable ions such as Ca2+, Mg2+, Al3+, Fe3+ and Fe2+ demonstrate considerable influence on the floatability of the minerals. In this study, flotation test, zeta potential test, and solution chemistry calculation were adopted to investigate the mechanism of how these metal ions affect the floatability of ilmenite and titanaugite in different pH conditions. The results show that in weak acidic solution, Ca2+ and Mg2+ mainly freely exist in the solution with little adsorption on mineral surface, and their reaction ability with oleate ions is weaker than active site on ilmenite surface (Fe), thus they show negligible effect on the flotation of ilmenite; Al3+ shows similar reaction ability with oleate ion compared to Fe3+, which lead to competitive reaction with collector, so the flotation of ilmenite is depressed. While Fe3+ can adsorb on surface of titanaugite in the form of Fe(OH)3, and it shows stronger reaction ability with oleate ion compared with active site on titanaugite surface (Ca and Mg), which proves an activation effect on titanaugite flotation. In alkaline solution, all these five kinds of ions can adsorb on titanaugite surface, and the floatability of titanaugite will be activation. Based on the above analysis, it can be deduced that in the flotation system using fatty acid as collector, the adsorption of metal ions on mineral surfaces and the stronger reaction ability with collector than active site on mineral surfaces, are the two prerequisites for metal ions show activation effect on mineral flotation.INTRODUCTIONIn flotation pulp, the existence of metal ions is often inevitable. There are two sources for these metal ions: the first part is generated in grinding and flotation process due to the oxidation, reduction, corrosion or dissolution of minerals or grinding medium; the second part is from the flotation water or the addition because of the technology need. The metal ions in the pulp have a considerable influence on mineral flotation. Earlier researches are focus on the activation effect of mineral floatation by metal ions to obtain a higher flotation efficiency, many effective activators were found, such as Cu2+ activated sphalerite, Pb2+ activation wolframite, and Ca2+ activation quartz flotation, these metal ions have become the commonly used activators in industrial production. And many studies attempted to explain the mechanism of how metal ions affect the floatability of minerals. James (James et al, 1972) suggests that metal hydroxide precipitation is the main component leads to activation effect, while the study of Fuerstenau (Fuerstenau, 1976) showed that the metal ion hydroxyl complexes played significant role. In recent years, the reuse of mineral processing wastewater has attracted more attention (Rao et al, 1989; Liu et al, 2013; Wang et al, 2014), as a main component in flotation wastewater, the influence of “unavoidable ions” on flotation process still need in-depth study."

Jan 1, 2018

By Augustine O. Orumwense, Micheline Boisclair

"The use of stirred mill to complement tumbling mills in grinding fine grained minerals is increasingly becoming an attractive processing option. Parameters such as agitation speed, grinding media type and size, feed pulp density, and grinding time were studied in order to elucidate their impact on stirred milling. Test results showed that the parameters have a profound effect on stirred mill efficiency and operating cost. A comparative test with a tumbling ball mill was also made and the specific energies of both mills in fine grinding were analyzed. A difference of over 40% in energy savings particularly when the product size is smaller than 20 µm was obtained with the stirred mill.INTRODUCTIONIn industrial processes where very fine and ultrafine particles are required such as in chemical, ink, food, paint and lacquer, pulp and paper, plastics, pharmaceutical, metallurgical and ceramic industries, the use of stirred mills for grinding is well established. Mineral processing plants are gradually shifting focus to the use of stirred mills for fine grinding and /or regrinding purposes as the target liberation size gets very small. A number of plants processing finely/sparsely disseminated ores are known to have adopted stirred milling technology for their fine grinding needs (Enderle et al., 1997; Harbort et al., 1999; Gao et al., 2000; Davey, 2003 & 2006; Pease et al., 2006).There are different kinds/designs of stirred mills available on the market but, all can be divided into two sub groups namely fluidized and non-fluidized types. The non-fluidized stirred mills consist of Tower mill, Vertimill, Sala agitated mill (SAM), and ANI-Metprotech (SVM). These mills are characterized by their low-speed and the use of fairly coarse grinding media size, 3 – 20 mm. Hence, they are mostly suitable for relatively coarse grinding application. The fluidized type includes the Isamill, Netzsch mill and Stirred mill detritor (SMD). These mills have a characteristic high agitator speed, use fine grinding media size of 0.5 – 5 mm, and are employed in very fine grinding operations. The superior fine grinding capability of stirred mills is attributable to two main process parameters, which are the use of fine grinding media and a high mill speed."

Jan 1, 2008

By Daniel Briones

El presente trabajo señala las bases que fundamentan la aplicación de los Sistemas de Gestión Integrados y se ofrecen argumentos que sustentan los mecanismos usados para integrar los sistemas de Seguridad (NOSA), medio ambiente (ISO 14001) y calidad (ISO 9001); y la necesidad de su uso como herramienta de gestión por parte de la organización, llegando a todos los niveles hasta alcanzar la madurez del Sistema. Asímismo, se describen algunos ejemplos del impacto positivo, que ha significado la implementación de este Sistema en la unidad de producción Uchucchacua (cuarta productora mundial de Plata,), desde el inicio del Proyecto, hasta lograr la revalidación de la Certificación de las normas ISO 14001, y la cercana certificación en OHSAS 18001 e ISO 9001.

Sep 12, 2005

By C. N. Rosenecker

The power required to circulate a gas-solids suspension was determined using a centrifugal compressor and a closed system. The suspension consisted of 18- to 40-micron glass beads in a mixture of 89 percent N2 and 11 percent CO2 at 20 psig. Solids-to-gas (S/G) ratios w re O to 2.2 lb/lb; gas flow rates were l.2 to 2.5 lb/min. Power requirement was found to follow the relationship hp t = hp(. + l), where hp t = the total power, and hpg = the power required for pure gas.

Jan 1, 1967