Search Documents

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By S. Steinlechner, S. Wegscheider

"In the past, the metallurgical industry was most of the time dedicated on their main commodity, recovering base metals like zinc, copper or lead but leaving other valuable side elements in the generated residues. As a result, these accompanying minor elements, like gold, silver, indium or also PGMs can be found in the dumps of the corresponding industry. Because of political unrest, strikes, economic reasons or decreasing primary resources leading to a high supply risk, also those mentioned minor elements moved into the focus of the recycling industry. Therefore, beside the base metals, first of all the recovery of those minor metals would be of high interest contributing to the economic viability of recycling processes, although they occur in much smaller quantities in materials. In this context, residues from zinc industry, like leaching residues or precipitation residues show high potential to carry silver as well as indium next to lead and zinc. Therefore, the paper summarizes carried out thermochemical calculations investigating a possible recovery of silver as well as indium by volatilization and the influence of zinc and lead on this process. Based on these theoretical investigations with HSC, trials in lab scale were done verifying the obtained results.INTRODUCTIONHuge amounts of iron precipitate, mainly jarosite get landfilled every year although there is a high content of valuable metals in this residue beside iron. Nevertheless, jarosite has to be dumped due to the presence of contaminating heavy metals. The accumulation of these residues takes up massive land on the one hand but also causes a series of environmental problems in ecosystems on the other. Moreover, some toxic ingredients such as arsenic and cadmium can be dissolved in rain water and are therefore harmful to the health of the aquatic systems. (Erdem & Özverdi, 2011; ÖzverdI & Erdem, 2010) Approximately 0.5 t of dry jarosite accumulate in the production of 1 t of zinc by the hydrometallurgical zinc-winning route (Svens, 2010). Jarosite is a precipitation residue formed during the iron removal. In general, the iron already exists in the zinc ore which is why zinc ferrite builds up during the roasting step of the zinc ore. Zinc ferrite is only soluble in strongly acidic solutions and during the hot acid leaching step it gets dissolved while zinc and iron enter the solution. It is necessary to get rid of the iron because otherwise it would deposit on the cathode first due to its precious character which would be harmful in the zinc-winning electrolysis. Nevertheless successful investigations were done by adding chlorine to the jarosite to recover silver. These findings leads to another residue which occurs in huge amounts – electric arc furnace dust (abbreviated with EAFD) from the iron and steel industry. In 2013 the annual electric steel production reached about 451 million tons. Around 15-20 kg of EAFD is produced per ton of steel in an electric arc furnace (EAF), creating approximately up to 9 million tons of dust per year. (Grabda, Oleszek, Shibata, & Nakamura, 2014; World Steel Association) Next to elements like zinc, lead and iron, chlorine and fluorine are present in this dust. While galvanized steel plates in the scrap act as a source for zinc, casting powders, flame retardants and synthetic coatings are responsible for the chlorine and fluorine contents in the dust."

Jan 1, 2016

By W. Bonfield

The microstrain characteristics of a polycrystal-line Cu 1.9 wt pet Be precipitation-hardening alloy have been determined for various conditions of aging. The friction stress remained constant for all the conditions investigated, whereas the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-8 in. per in.) and the three-stage stress-strain curve in the microstrain region were sensitive to changes in dislocation and precipitate distribution. Correlations between the measurements of microplasticity and electron-nzicroscope observations of substructure are considered. ALTHOUGH the macroscopic mechanical properties of Cu 1.5 to 2.0 wt pet Be precipitation-harden ing alloys were established' in some detail, there has been no previous investigation of the nature of microyield-ing in these alloys. This paper describes a high-sensitivity extensometer determination of microplasticity in polycrystalline Cu 1.9 wt pet Be, in which the friction stress, the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-6 in. per in.), and the rate of strain hardening in the micro-strain region were measured for various conditions of precipitation. The structural changes accompanying aging in this alloy were examined using transmission electron microscopy, a study which differed from previous investigations as, in order to minimize grain boundary precipitation effects,' the solution-treated alloy was cold-rolled to 40 pet reduction prior to aging. Hence the extent of recovery and recrystalliza-tion, as well as the variation of precipitate morphology and distribution, were assessed. From these results possible correlations between the microstrain characteristics and the observed precipitate and dislocation structure are considered. EXPERIMENTAL PROCEDURE The material investigated was a commercial copper beryllium alloy (Berylco 25), which had a com- position of 1.9 wt pet Be and 0.2 wt pet Co. The alloy was solution-treated at 800°C, quenched in water, and then cold-rolled to 40 pct reduction. Tensile specimens of gage length 1 in. and rectangular cross section of 0.18 by 0.06 in. were prepared from the solution-treated, cold-rolled material and aged for 15 min, 2, 24, and 100 hr at 315°C and 24 hr at 425°C to produce a range of precipitate structure. The hardness values associated with these conditions are listed in Table I. It can be seen that a maximum value is obtained after 2 hr at 315oC, which decreases with continued time at temperature to a minimum after 24 hr at 425°C. For comparison some as-solution-treated specimens were also aged for 2 hr at 315°C. The specimens heat-treated to a given condition were examined in two ways. First, the nature and distribution of the precipitate and dislocation structure was characterized using transmission electron microscopy. Thin foils were obtained from the specimens by electrolytic polishing in a 30 pet nitric acid-alcohol solution at -20oC, and were examined in an RCA EMU 3 electron microscope. Second, the mi-croplastic behavior of the specimens was measured with a Tuckerman strain gage, using the load-unload technique previously described2, 3 to determine the friction stress, the microscopic yield stress, and the variation of plastic microstrain with stress. RESULTS 1) Structural Changes During Aging. a) Annealing Processes. The solution-treated, cold-rolled Cu 1.9 wt pet Be had an irregular dislocation-cell structure,

Jan 1, 1968

By G. S. Rice, H. P. Greenwald, H. C. Howarth

"""Rock-dust barriers""5 as they are termed in this country, are for the purpose of confining a coal-dust mine explosion to the limited area in which it originates. These barriers were first tested in 1910-1911, with favorable results under the conditions of test, at the French official gallery which was then at Lieven, Department of Pas-de-Calais. Shortly afterwards the Bureau of Mines in the course of its investigation of all practical explosion-prevention methods tried barriers in the Experimental Mine near Bruceton, using the primary form of simple fixed cross shelves 20 inches wide extending over the passageway and laden with rock-dust. The Bureau termed them “Taffanel barriers"" in honor of the director of the Lieven testing station. The trials were made in conjunction with tests of explosibility of different coal-dusts.Experience showed that although the principle of barriers had merit when they were used for secondary defence, the primary form was uncertain in effectiveness. This led the senior author to design mechanically discharging barriers to be operated by the compression air waves which precede the flame of an explosion. For the better understanding of the principal involved, it is pointed out that the advance air waves are what make a coal-dust explosion possible by stirring up the coal-dust from the walls and floor of the passageway. If a barrier can throw inert dust into the air to form a cloud as dense or denser than that formed by the coal-dust, it will neutralize the explosiveness of the coal-dust, and the flame of the explosion will be extinguished. When the flame ceases, the pressure dies away in a short distance if the 'area that had been traversed by the explosion is not large."

Jan 1, 1930

By N. N. Moebs

The atmosphere in part of an air-sealed coal mine was monitored continuously through a drill hole for oxygen content to determine the effectiveness of sealing a mine against the entrance of air and the major force that caused the phenomenon of mine breathing through the overburden. The differential pressure across the seal and the barometric pressure on the outside also were recorded. A general correlation, obtained between the oxygen level, differential pressure, and barometric pressure, indicates that changes in air pressure are the cause for periodic replenishment of the oxygen in the mine. Mine effluent quality was determined by conditions in many sections of the mine and could not be related to the oxygen level at the drill hole.

Jan 1, 1972

By A. Wieniewski

The observed progress in technology of non-ferrous ores enrichment and condition of machines and equipment in the ores concentrators on the one hand have brought a possibility and on the other resulted in necessity for introduction of modernization actions. Positive results of investigations into influence of chemical modification of selected products of enrichment process on copper ores enrichment results gave possibility for implementation of chemical-flotation technologies of ores enrichment. The substantial development in flotation machines structure has contributed to modernization of flotation process resulting in increase of enrichment efficiency. The paper presents the idea and results of chemical modification of difficult in enrichment semi-products in the technology of copper ores enrichment and the results obtained after application of the modernised technology. The structure of large-volume flotation machines used in various stages of flotation and current situation in modernization of flotation process in copper ores concentrators are also described. The paper presents industrial-scale results of flotation after application of modified flotation reagents of collector group. Introduction of modifiers into the widely used xanthates resulted in increase of copper recovery in concentrate.

Jan 1, 2014

By John M. Kelly

New Mexico produced 39,751,868 bbl. of oil in 1941 and ranked seventh among the oil-producing states. Its 1941 production established an annual record, exceeding the 1940 record year by 854,498 bbl. The average daily production for the year was 108,909 bbl. The average daily non-marginal well allowable for New Mexico on Jan. I, 1941, was 36 bbl.; at the close of the year it was 43 bbl. The average daily pipe-linc runs were approximately 3 per cent less than the allocations of the New Mexico Oil Conservation Commission, which followed closely the recommendation of the United States Bureau of Mines in setting the daily outlet demand. The production in Lea County was 34,333,448 bbl.; Eddy County, 5,009,354 bbl.; and northwestern New Mexico (San Juan and McKinley Counties), 406,306 barrels. The total number of completions in the state was 402, of which 301 were oil wells, 19 gas wells, and 82 dry holes. Drilling during 1941 was 68 per cent of 1940, and the ratio of dry holes to producers, I to 4, was the greatest since 1935. Of these dry holes 43 were drilled in proven fields and 39 were wildcats. One new oil field and one new gas field were discovered as a result of the 1941 wildcatting program. However, numerous extensions were made to the existing fields, which, although they were called extensions to proration areas, were in reality field discoveries, being on separate geologic structures. Southeastern New Mexico Lea County The Monument field was the largest producing field in Lea County, with 6,973,808 bbl. It was closely followed by the Eunice field, with 6,644,181 bbl.; Vacuum field, with 4,800,608 bbl. and Hobbs, with 3,624,159 bbl. Hobbs field, however, still has the largest total recovery, this being 97,407,929 bbl. at the end of 1941. The new oil-field discovery in Lea County during 1941 was the Salt Lake field, T. 20 S., R. 33 E. The discovery well was Leonard-Welch State No. I, NW. NW. of sec. 18, T. 20 S., R. 33 E. This well was drilled to a total depth of 3103 ft. and was completed for an initial production of 250 bbl. per day pumping. The oil is 26" gravity and the producing horizon is in the San Andres limestone of Permian age. The discovery well was completed on June 22, 1941, and since that date four more producers have been completed, with no failures. The area is about 10 miles north-west of the Lynch pool, to which the oil from this field is being trucked because there is no pipe-line connection. The greatest drilling activity during 1947 was in the Maljamar field of western Lea County, with 62 completions, 59 being oil wells and 3 dry holes. The limits of this pool are now being defined on the north and south but to date have not been defined either to the east or west. The total number of 40-acre oil-producing units in the field at the close of the year was 158. On April I, 1941, a pressure-maintenance project was installed at the southern end

Jan 1, 1942

By R B. Turner

The authors have studied and analysed many mineral resource and related projects in Australia. These studies have lead them to conclude that the past performance of many project developers does play a major part in any external financial investment for new or expanding resource based projects. In this paper the authors look particularly at the influence of parties outside the direct control of developers and the effect of' these parties on projects and conclude with a number of points as guidelines for potential project developers.

Jan 1, 1980

By H. J. Meyer

"A hydrostatic elevation difference meter has been developed for use in measuring elevations along gravity traverses. Elevations of stations 100 feet apart can be obtained at a rate of 1/2 mile per hour and to an accuracy better than 1/3 foot. This can be done along traverses which have not been cut and chained. The instrument is durable, lightweight and constructed of materials which will withstand any temperature encountered in field work.It is believed that this device will more than double the rate at which gravity surveys over mining prospects can be carried out."

Jan 1, 1972

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By M. Abzalov

"Control of analytical data quality is usually referred to in the mining industry as Quality Assurance and Quality Control (QAQC), and involves the monitoring of sample quality and quantification of analytical accuracy and precision. QAQC procedures normally involve using sample duplicates and specially prepared standards whose grade is known. Numerous case studies indicate that reliable control of sample precision is achieved by using approximately 5% to 10% of field duplicates and 3% to 5% of pulp duplicates. These duplicate samples should be prepared and analyzed in the primary laboratory.Bias in the analytical results can be identified by inclusion of 3% to 5% of the standard in each sample batch. Several different standards are used, with values spanning the practical range of grades in the actual samples. A blank (a sample in which the concentration of metal of interest is below detection limit) should also be included. Standard samples alone cannot identify biases introduced during sample preparation, and therefore approximately 5% of the duplicate samples (coarse rejects and pulp) should be processed and assayed at another, external, reputable laboratory.This paper discusses techniques used for estimation of errors in precision and accuracy, and overviews diagnostic tools. It is shown that one of the most commonly used methods, the Thompson-Howarth technique, produces consistently lower results than other methods. These results reflect the nature of this method, which relies on the assumption of a normally distributed error, and thus produces biased results when errors have a skewed distribution. This study concurs with the suggestion of Stanley and Lawie (2007: Exploration and Mining Geology, v. 16, p. 265-274) to use the average coefficient of variation (CVAVR(%)) as the universal measure of relative precision error in mine geology applications: Le contrôle de la qualité des données analytiques est habituellement désigné sous l’appellation d’Assurance et Contrôle de la Qualité (ACQ), elle implique le suivi de la qualité des échan¬tillons et la quantification de la reproductibilité et la précision analytiques. Les procédures des pro¬grammes d’ACQ impliquent habituellement l’usage de duplicata et de standards analytiques dont la teneur est connue. Plusieurs études de cas indiquent qu’une bonne fiabilité du contrôle de la précision des échantillons est atteinte par l’usage de 5% à 10% de doublons sur le terrain et de 3% à 5% de doublons de pulpe. Ces duplicata devraient être préparés et analysés au laboratoire principal.Un biais des résultats analytiques peut être identifié par l’inclusion de 3% à 5% d’échantillons standard dans chaque envoi d’échantillons. Plusieurs standards sont utilisés, avec des valeurs couvrant l’étendue des teneurs habituellement rencontrées dans des échantillons réels. Un blanc (un échantillon dans lequel la concentration d’un métal donné est sous la limite de détection) devrait aussi être inclus. L’emploi exclusif d’échantillons standards ne permet pas l’identification de biais résultant de la préparation des échantillons, de telle sorte qu’environ 5% des duplicata (rejets grossiers et pulpes) devrait être traités a un autre laboratoire indépendant et fiable.Cet article passe en revue les techniques utilisées pour évaluer l’erreur liée à la précision et a la reproductibilité, et effectue aussi un survol de divers outils diagnostiques. Il ressort de cet examen qu’une des techniques les plus fréquemment utilisées, la méthode Thompson-Howarth, fournit des estimés systémati¬quement inférieurs à ceux provenant des autres méthodes. Ces résultats sont un reflet de la nature de cette méthode, laquelle assume une distribution normale de l’erreur, biaisant ainsi les résultats lorsque l’erreur présente une distribution asymétrique. La présente étude recommande de privilégier l’usage du coefficient moyen de variation (CVAVR(%)) en tant que mesure universelle de la précision relative de l’erreu"

Jan 1, 2008

Application of technology to the search for new deposits went on apace in 1963. Traditional methods, aided by modern communications, were successful in some out-of-the way corners of the world that had not been adequately prospected, but the co-ordination of several mutually supporting techniques is necessary to define exploration targets in most areas today. Although these obviously include geophysics and geochemistry, which are treated elsewhere in this issue, geology continues to play a major role. As the search focuses on less and less obvious targets there will be more need than ever to "pull out all the stops." Any anomaly may have significance and must be evaluated as a possible lead. Ability to detect them increases as the laboratory workers refine techniques for measuring physical, chemical, and isotopic properties; it will be increasingly the responsibility of the exploration geologist to understand and apply these to economic problems. Simple propecting, the search for outcrops of recognizable ores of traditional types, was perhaps most successful for iron. Potentially large deposits of high-grade magnetite-specularite-hematite ore have been found in the Mary River area near the north end of Baffin Island. The ore holds up four hills that stand some 1500 ft above the surrounding country; obviously they were ripe for discovery by the first person to come across them, in this case Murray Watts, president of British Ungava Explorations, Ltd, As preliminary examination indicates a lump ore averaging 68 to 70% iron, these deposits may be commercial in spite of the unfavorable climate and their isolation from world markets.

Jan 2, 1964

By William R. Yernberg

The 2002 Arizona Conference was held Dec. 8 and 9, 2002, at the Doubletree Hotel at Reid Park in Tucson. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The meeting featured a keynote address, a distinguished lecture and about 30 technical papers. As was the case at the 2001 meeting, the economy, the price of copper and foreign competition continue to be the hot topics of discussion among the attendees. The domestic copper industry still faces challenges due to low copper prices dictated by the world market and because of a weakened domestic economy. There continues to be concern about the Arizona region’s copper industry in light of the mergers, downsizing and shutdowns that have occurred during the past several years.

Jan 1, 2003

By Turno De Michelis

The Porto Marghera plant was erected in 1936 for the production of 10,000 tons of electrolytic zinc annually. Since then it has been continuously enlarged until annual production of the metal reached 40,000 tons in 1969. At the same time the processing cycle was modified bringing it up to date with modern techniques, and was completed by installations for the recovery of by-products in the minerals treated and subsequent processing of the base metal. 90% of the zinc produced is of 99.993% purity . At present the plant comprises, first of all, the zinc blende desulphuration department which has a single modern fluid bed furnace capable of processing 220 - 250 tons of dry crude mineral daily; it is connected to the sulphuric acid plant with its three catalysis sections each capable of producing 60-70 tons of sul9huri.c acid monohydrate daily. The roasted blende is conveyed pneumatically to plants for leaching of the zinc and purification of the resulting solution. During recent years this department has been completely transformed from the discontinuous cycle, for which it was built, to the continuous cycle, paying great attention to

Jan 1, 1970

By C. Cornejo, C. Schuffeneger, J. Rosas

"At the end of 2010 the AMSA Esperanza Concentrator started commissioning. Located in the Atacama Desert this project is the first of several large size concentrators developed recently to operate in Northern Chile. In addition to the new operations to be implemented in the short term, many existing installations are planning expansions. The use of large size equipment is one of the common characteristics of the new concentrators, but also new technologies are being considered and innovation is present in most cases. Sea water or desalinated water will be required to process large tonnages of sulphide copper ores as well as gold bearing ores, since process water supply from the Andes will no longer be available. The high cost of sea water or desalinated water supply and the high cost of energy are not a limitation as the current metal market scenario allows obtaining an attractive NPV even from installations designed to process relatively low grade ores. A review of the current concentrators being developed in Chile is presented, including a description of the main design issues related to technology and innovation. An analysis of the Chilean mining industry is also presented, detailing mine and plant capacities as well as expected final products.INTRODUCTION The mining sector in Chile has become a reference when analysing the large concentrator plants projected or currently in operation all over the world. At present and as a consequence of the high price of metal commodities, most South American countries have an active mining sector. Chile is known as a major producer of metals. First records of copper production exported to Spain are dated to the early XVII century. Since then Chile has produced over 13% of the total copper ever produced in the world. After 1990 Chilean mining and the associated cluster of activities has substantially grown to levels never reached before, especially in the production of copper, gold and other non-metallic minerals. This dramatic increase is the result of an economic policy based on delivering comparative advantages and incentives for the admission of foreign capital to offset the weak domestic investment in previous decades. Massive mining of its huge mineral resources has allowed Chile to be a world leader in the production of copper and other base metals and mineral products."

Jan 1, 2012

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hydroscillator. This increased grinding efficiency 28 pct over conventional units.

Jan 6, 1950

By L. I. Rosato

A novel hydrometallurgical process for the recovery of silver and gold from neutral leach residue that is based upon leaching with thiourea, is described. Laboratory and pilot plant studies have shown that 80-90% of the silver and 60-70% of the gold can be recovered by:? ( i) leaching zinc calcine with 'Spent electrolyte at pH 2.0-3.0 to generate a precious metal-bearing zinc ferrite residue, (ii) leaching of the thickened zinc ferrite with 3-5 g/L thiourea in a six stage carbon-in-pulp circuit, (iii) elution of silver and gold from the loaded carbon with a thiourea- butanol solution, (iv) thermal regeneration of the stripped carbon and (v) recovery of the precious metals from the pregnant eluate by cementation with zinc dust. The reasons for adopting the thiourea CIP leach and the preferred operating parameters for each process step are presented. The requirements for the destruction of any thiourea transferred to the zinc circuit are outlined, and the results of an integrated one tonne/day pilot plant operation at Canadian Electrolytic Zinc are given.

Jan 1, 1990

By L. H. Duschak

"This paper is based on the results of work conducted of the bureau's experiment station at Berkeley, Calif., in connection with the investigation of properties and methods of utilizing Western magnesite. The experiments described herein were made under the supervision of the writer, by W. C. Riddell and E. H. Delius, of the station's staff.In calcining magnesite for the production of magnesium oxide to be used in the preparation of oxychloride cement, the calcium carbonate present in the original rock may remain unchanged or appear in the finished product, either as CaO, or in combination with SiO2, A12O3, etc. As there is reason to believe that free CaO may have an effect on the behavior of caustic magnesia in the cement reaction, it is desirable to have a method for the determination of the relatively small amounts of free CO in the presence of a large quantity of MgO.The extraction of the free CaO with water free from CO2 at once suggests itself as a possible method. The solubilities of Ca(OH2)2 and Mg(OH)2. are given by Seidell in his book an ""Solubility of Inorganic and Organic Compounds."" (2nd Edition, 1919) as follows:"

Jun 1, 1920

By Lane White

The 1989 Annual Meeting and Exhibit of SME in Las Vegas, NV, February 27 - March 2, 1989, was the largest ever, drawing more than 4000 regis¬trants and 240 exhibit booths. Technical sessions included presentation of nearly 500 papers, including symposia on Biotechnology in Minerals and Metals Processing, Surplus Capacity in the International Metals Industry, and APCOM `89 - the 21st International Symposium on Application of Computers and Operations Research in the Mineral Industry. Technical sessions covered the gamut of minerals industry interests; however, the proximity of the meeting to recently surging gold development in Nevada drew special attention to gold operating practices. Several of the papers on gold processing are reviewed below. To keep pace with the strong world- wide interest in gold development, SME has scheduled three additional upcoming programs that will focus specifically on gold: World Gold '89 - Gold Forum on Technology and Practices will be held November 5 - 8, 1989 in Reno, NV, as a joint meeting and exhibit between SME and the Australasian Institute of Mining and Metallurgy. Technical sessions will encompass a full program of papers covering geology and exploration, mining, and mineral and metallurgical processing. Cooperating sponsors for this meeting include the Canadian Mineral Processors Division of CIM, The Institute of Metals, The Institution of Mining and Metallurgy, The Mining, Geological & Metallurgical Institute of India, and The South African Institute of Mining and Metallurgy. Gold '90 - Salt Lake City, UT, February 26 - March 1, 1990, will be a symposium held in conjunction with the 1990 SME Annual Meeting. Current research on the processing of refractory gold ores will generate innovative papers on process mineralogy at this symposium, with special emphasis on gold with pyrite and gold with carbon. Other sessions are planned for gold exploration and mining, gold metallurgy, gold plant design and practice, and gold in scams. Advances in Gold and Silver Processing Conference, October 1 - 3, 1990 will be held in Reno, NV. Preliminary planning calls for technical sessions on heap leaching practice, refractory ore processing, non-traditional lixiviants, bioleaching, metal recovery from solution, and the environmental aspects of processing operations. PLANT DESIGN, OPERATION Technical sessions organized by the Minerals and Metallurgical Processing Division of SME at this year's meeting in Las Vegas covered a wide range of gold operating practices. Eight papers relating to gold plant design, operation, and equipment are summarized here. Preprints of these papers are available by writing to Publications Sales, PO Box 625002, Littleton, CO 80162-5002 ($2.50 per paper for AIME members, $4 for nonmembers). Continuous elution process A. M. Stone, of Bechtel Australia Pty. Ltd., described the "Development of the Continuous Elution Process for Extraction of Gold from Carbon" (pre-print 89-75). Developed by Bechtel Pacific Corp. for Ok Tedi Mining Ltd., the Continuous Elution Process uses the same reagents as batch processes for elution of gold from carbon, while yielding significant savings in stripping vessel size and energy consumed in comparison with equivalent batch processes. The process is also simpler to operate than batch processes. Other advantages include reduced maintenance costs, higher average eluate grade, and near steady final eluate grade. Pilot testing for the Continuous Elution Process was conducted at Western Mining's Kambalda gold plant beginning in December 1982. The Continuous Elution Process is a continuous countercurrent system operating in a pressure vessel at elevated

Jan 1, 1989

By Wolfgang Baum

Case studies from epithermal gold-silver deposits in the western United States and in Latin America show that the routine use of process-related mineralogical studies has become an important tool for the reduction of development, capital and operating costs. Bypassing the mineralogical characteristics of epithermal gold-silver ores, as a result of fast-track development approaches, has resulted in multimillion dollar metal losses and/or in considerable modification costs of existing operations.

Jan 1, 1988