Search Documents

By Howard N. Eavenson

Waste of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. Average Recovery The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered—it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed 'that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed—often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal—is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1947

By D. W. Rogers

Several commercial polyacrylamide flocculants most widely used in Western Canadian mineral processing plants have been analyzed chemically and compared in standardized settling tests as aids to thickening and clarification. Data are included for both dry and liquid-type flocculants. Percentages of active ingredients in these commercial products varied Widely. Performances were compared on the basis of: equal additions of active ingredients, nearly equal molecular weights and nearly equal degrees of ionic character. Based on zone settling velocities and supernatant clarities of siliceous slurries coagulated by lime additions, dry flocculants proved more economical than liquid flocculants. Using these same two criteria, the most highly anionic were more effective than either weakly anionic or non ionic polyacrylamide- type flocculants.

Jan 1, 1978

By R. W. Smith

It is well known that certain silicates such as the feldspars and beryl can be readily floated from quartz at a low pH value using a long chain cationic collector in the presence of a fluoride.1-3 However, the mechanism whereby the fluoride activates feldspars and beryl is not known. Indeed, only a few authors have even speculated about possible mechanisms.1,3,4 As a first approach to the problem, it is perhaps best to look closely at the interesting character of hydrofluoric acid and how it dissolves silica and silicic acid. Hydrofluoric acid, unlike hydrochloric acid, is a weak acid with a dissociation constant of about 3.53 x 10-4 at 25°C.5 The reason for the weak acidic character of HF lies in the very small size of the fluoride ion.6 The pKa value is 3.45 which means that at pH 3.45 half the HF is present in molecular form and half in ionic form. The anion present is probably HF2.-6 At pH values below the pKa value, molecular concentration increases rapidly at the expense of the HF2- anion. It is known that HF readily attacks glass, silicates, quartz and silicic acid. The equation usually cited pertaining to the first step in HF attack of silica is6-'

Jan 1, 1965

By C. L. M. Gough, L. A. Vermeulen, D. D. Howat

Formulae expressing the dependence of the mass of a grinding ball on the amount of material milled by a ball mill are derived. It is shown that, with the aid of these formulae, it is relativel rsimple for the results of a marked-ball test to be analysed and for the relative performance and cost-effectiveness 0 the various types of ball under test to be evaluated. Predictions based on theory and the results obtained in a marked-ball test in a ball mill are compared detail and shown to be in close agreement. The difficulties associated with marked-ball tests are considered, and an explanation for the decrease in the calculated consumption of the balls, which follows naturally from the theory, is presented. The marked-ball anomaly explained, and it is demonstrated that the ball consumption in a ball mill can be predicted with fair accuracy from the results of a marked-ball test.

Jan 1, 1983

By J. Stowe

"While there has been continual improvement in the models for predicting deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life.Tailings pipelines are increasingly operated at higher solids concentrations when there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar-flow pipeline operation is possible as there are several operational laminar-flow tailings pipelines. While our understanding of laminar-flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines.New sensor technology has led to the development of an instrument that provides reliable indication of bed-deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar-flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines.This article provides an overview of the each of the above advances in the design and operation of tailings pipelines.Operating tailings pipelines with a depositTailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit."

Jun 1, 2019

By Ellsworth R. Spencer

An assessment of U.S. western hardrock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hardrock mining machines. Of the operators, 96% had daily noise doses that exceeded the U.S. Mine Safety and Health Administration?s (MSHA) permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214% and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jackleg drill. These results will be used to help prioritize noise control development by NIOSH and other partners.

Jan 3, 2010

By J. W. Whitney

Itronics Inc., through its wholly owned subsidiary Itronics Metallurgical, Inc. (IMI), has successfully developed technology that allows it to be fully integrated as a photochemical recycler. IMI is now using this technology to expand its regional operation, which collects used photographic chemicals, chemically removes 99.997% of the silver and uses the residual to make a line of high quality liquid multinutrient liquid fertilizer products. Elevated silver discharges from the Reno-Sparks sewage treatment facility, that were traced back to incoming waste photographic chemicals and which were seriously impacting the sensitive fishery, provided the impetus for this project. This paper is updated from a paper presented at the Twenty-Second International Precious Metals Conference Toronto, Ontario, Canada in June 1998. It presents an overview of the scope of the problem solved by the technology, some of the permitting and development issues, and some of the specific fertilization formulations that are now being marketed.

Jan 1, 2000

By Dan Nilsson

The Luossavaara "Research Mine" is the First large, offensive effort in mining research conducted by the Swedish state. Over a 5-year period, 1981-1985, the Swedish Mining Research Foundation works in the "Research Mine" on the development of mining systems and equipment. The purpose is to bolster the competitive strength of the Swedish mining and mining equipment industry. The previosly abandoned Luossavaara mine in Kiruna, in northern Sweden, has been reopened especially For the project. Ore is mined and sold during the course of the research project. The income from the sales covers a large portion of the costs for teh research.

Jan 1, 1985

By Dennis V. D’Andrea, Robert C. Steckley, William C. Larson, Richard A. Dick

A fragmentation experiment was performed in cooperation with Duval Corporation in a porphyry copper molybdenum deposit near the Sierrita pit south of Tucson, Ariz. A 10-hole test blast was detonated to establish relationships between blasthole spacing and the resulting fragmentation. Blastholes were 9 in. in diameter and 110 ft deep. The 10 blastholes contained a total of 17,400 lb of aluminized slurry blasting agent in 50-ft columns with 60 ft of stemming. Blasthole spacings of 25, 20, and 15 ft were tested. Diamond drill core examination was the primary method used to determine the condition of the rock before and after blasting. Topographic surveys were used to measure the rock swell produced by the blast and a fragment size distribution was obtained for the rubblized material on the surface. The rubble zone at the surface was ideal for in situ leaching. Fragmentation to depths of 110 ft was excellent from the 15- to 20-ft blasthole spacing patterns. Good breakage was also produced by the 25-ft pattern although the effects of the blast were not as obvious. In situ leaching tests were not conducted. However, based on size consideration only, all three blasting patterns produced adequate breakage for successful leaching.

Jan 1, 1974

By Earl L. Hastings

Although the principal market for diatomite in the United States is in the East,4 production of the material is presently restricted to the West, because the deposits are larger, mining costs are cheaper, and the quality of product is better than that obtained from other domestic deposits. However, Tallahatta diatomite, occurring in Choctaw and Clarke Counties, Ala., has a freight rate advantage, which should encourage competition for those market that are now being supplied with the purer diatomites from the western deposits. For this reason, diatomite occurrences in the Tallahatta formation were examined by the Bureau of Mines and physical properties of samples from the deposit were determined to obtain additional data for use by any potential producer who wished to evaluate the material for its commercial possibilities. In 1894 K. M. Cunningham5 found that the buhrstone formation (now known as the Tallahatta formation) contained "siliceous shells of marine diatoms, radiolaria and foraminifera, thus being rather of the nature of tripoli or diatomaceous earth than of a true clay." Cooke6 and Semmes7 also reported the Tallahatta formation to be composed principally of diatomaceous earth with accompanying beds of sand, clay, and sandstone.

Jan 1, 1963

By C. E. Jordan

The Bureau of Mines conducted laboratory studies on methods to increase the recovery of brine from slime produced by operating potash plants. The slime was comprised of 80 percent brine saturated with KCl and NaCl, and 20 percent solids. A variety of settling techniques, filtration methods, continuous centrifugation, and novel processing techniques were investigated. Vacuum filtration recovered 6S percent of the brine at 47 gallons of brine per square foot per day. Pressure filtration, on the other hand, recovered 74 percent of the brine at 40.9 gallons of brine per square foot per day. Centrifugation in a 6-inch-diameter continuous decanter-type separator resulted in 42 percent recovery of the brine at a treatment rate of 542 gallons of brine per day. Vertical drains proved to be the most promising novel debrining technique investigated. With this method, 45 percent of the brine was recovered in 3 days.

Jan 1, 1977

By J. A. Beukes, M. Marais

TICOR South Africa is a new titanium feed stock producer. In the Ticor South Africa plant the ilmenite feed to the smelter plant is roasted to enhance its magnetic properties. This allows for the magnetic separation of chromite from the ilmenite. The magnetization reaction relies on partial oxidation with both under- and over-oxidation causing insufficient magnetization. To subject the roaster plant feed material to the required physical conditions a circulating fluid bed (CFB) roaster is used. This paper describes the development of a laboratory model that will aid in the control of the CFB roaster.

Jan 1, 2003

By William R. Yernberg

The “China & East Asia Mineral and Energy Re-sources Symposium — CEAR 2000” was held Jan. 23-26, 2000 in Denver, CO. Conference sponsors included Resources and Technology Symposia of Colorado and the Asian Journal of Mining. The meeting was attended by representatives from China, Japan, Mongolia, Korea, eastern Russia (Siberia) and the United States. The US attendees consisted of interested parties from mining and energy companies, financial institutions, consultants and government agencies. In his opening statements, L. Maness, Jr., president of Resources and Technology Symposia of Colorado, said that the “goal of the conference was to make jobs and friendships and to introduce people to each other.” The conference provided an opportunity for Western mining interests, including mining companies and investors, to meet with government agencies from both sides of the Pacific.

Jan 1, 2000

Jan 1, 2004

By Richard Moldenke

AmonG the things that will always remain to the credit of the foundry-industry is the circumstance that nearly all the research-work of practical value in daily routine was done by active foundrymen, and the results were freely given by them to the world. Moreover, while consumers felt that to them was due a more systematic and exact method of work, the foundry-men again were the first to act in the establishment of specifications under which their product should be sold. To come to more recent times, the American Foundrymen's Association has not only made an elaborate series of tests on cast-iron, and adopted tentative specifications based upon them, but, in addition, it has urged the International Association for Testing Materials, through its American representatives, to make the testing and specification of cast-iron a distinct issue. The half-hearted support first granted was greatly augmented by the rapidly-growing recognition accorded to the enormous iron-casting industry; and when the president of the American Society for Testing Materials was instructed to ask for a special commission for this purpose, Europe was ready to cooperate. During the Buda-Pesth congress, at, which America was represented by Prof. Howe, Mr. Wood and myself, it was decided to add five members to the general committee on steel and iron, whose special duty should be to conserve the interests of the cast-iron branch of the industry. America took up the work at once, and enlarged its committee to 67 members, all of whom were actively concerned in the manufacture or study of cast-iron in all of its branches. At the organization-meeting in Philadelphia, April 25, 1903, Mr. Walter Wood was elected chairman, and myself secretary; and, within a week thereafter, the sub-committees were appointed and became active at once. The scope of the work was naturally limited to those branches of the iron-casting in-

Jan 1, 1905

By E. A. Holbrook

RESEARCH, primarily, is finding out the truth. Research applied to engineering opens the door to new principles and processes, the application of. which benefits mankind in a material way. The engineer believes that investigation instituted with the primary view of making the results directly applicable to the industries is the highest type of research. Coal is essentially the basis of modern industrial civilization; therefore, any, considerable research pertaining to coal must link itself to the industry by, practical application of the results of the research. In other words, all investigational work connected in any way with coal leads to conclusions that permit a better understanding of the origin, nature of occurrence, composition, better and safer mining, more careful preparation, or greater efficiency in utilization of coal. Modern engineering research has been fostered essentially by universities and in the laboratories of institutions of learning. Coal problems that lend themselves to solution in the laboratories have been first attacked and are perhaps the farthest toward solution. For example, a great amount of research work has been carried out with the various phases of chemistry connected with coal. On the other hand, the equally important problems connected with methods of mining have received but little attention, primarily because their solution involves the continued use of a great and expensive laboratory, which is none other than the mine itself. As many of the problems already solved have had chemistry as their background, so many of the problems unsolved have physics as their background; there are also unsolved problems that deal in- coal economics. Even psychology must be called upon in future coal-mining research as a basis for solving those great problems that deal with human relationships. In general, considerable advance has been made in coal research dealing with chemistry, not so much progress has been made with problems having physics and engineering as a background, while there is a tremendous range of untouched problems that deal essentially with business and psychology.

Jan 9, 1919

By A. L. Mular

Si define la simulación digital y las técnicas de simulación son revisadas. La metodologia tipica conlleva la selección de modelos, el ajuste o reajuste de los datos primarios, la selección de una estrategia de acoplamiento, la valoración de la precisión del modelo en un sentido estadistico, y el desarrollo de estructura de simulación ejecutiva. La simulación sirve de ayuda para los ingenieros de procesos para evaluar la viabilidad de un esquema de flujo propuesto y el efecto de la modificación de un flujograma ya existente. Por otro lado, la simulación juega un papel importante en la optimación "off-line" y en la evaluación de estrategias de control de circuitos alternativos. Son presentados varios ejemplos para ilustrar estas utilizaciones para la simulación, incluyendo aplicaciones en los circuitos de trituración, circuitos de molienda y circuitos de flotación. Es de opinión de los autores que, dentro de la próxima década, las plantas de proceso de minerales serán estudiadas rutinariamente a través de una simulación digital durante las etapas preliminares de diseño. La simulación constituirá un importante componente en la toma de decisiones de un proceso.

Jan 1, 1982

By Zoltan Hajnal

Magnetic studies have been carried out on 88 surface and 157 underground samples from the Coronation Mine area of northern Saskatchewan. The intensity of the surface samples was compared to trace element determinations from the same locality. A good correlation was found between the titaniferous constituent of the rocks and the intensity of magnetization. From the direction of the remanent magnetism, two virtual geomagnetic poles were determined -latitude 12° 54' North, longitude 158" 17' West; and latitude 23" 42' North, longitude 163° 45' West. The sulphide ore specimens showed anisotropic susceptibility characteristics. A relationship was found between the measured maximum susceptibility values of the ore specimens and the direction of the tectonic forces which are considered to have formed the structure at the Coronation mine. Introduction T HIS paper summarizes the results of a study of the magnetic properties of samples from well-known Precambrian formations. The observed data give information for an interpretation of the magnetic field conditions in Precambrian times. The high magnetic intensity values indicate the importance of the study

Jan 1, 1965

In the past few years the Rietveld method emerged as a routine tool for quantitative phase analysis (QPA) from X-ray diffraction data. Fast and reliable results became possible by combining modern computer technology and optimised mathematical algorithms with the fundamental parameters approach in the Bruker AXS TOPAS software. Here the routine analysis of bauxite raw material and of aluminium bath electrolyte is presented. The accuracy of bauxite quantification was tested by analysing the IUCr round robin sample. An agreement of better than one per cent was obtained for minor constituents and a maximum deviation of 2.5 per cent for the major phases. This is excellent agreement with expected results from weighting. Ten different phases were quantified in natural samples from Turkey with a precision better 0.5 per cent for the major phases and one per cent for the minor phases. Additionally, crystallite sizes were obtained from the peak profiles that give valuable information for the processability of the material. XRD data from solidified aluminium electrolytes were rapidly measured using silicon strip detector technology. With the LynxEyeTM detector full patterns were collected in 90 seconds and analysed with TOPAS. It is shown how to derive well-established measures such as bath ratio and excess AlF3 from the Rietveld results. These measures are widely used in aluminium production and readily available with very high precision. The excellent agreement with ALCAN reference data demonstrates the outstanding accuracy of the method. The mean deviation between here presented results and reference data is below 0.5 per cent for total CaF2, below 0.25 per cent for excess AlF3 and 0.02 for the bath ratio. The precision of the method was evaluated by repeated measurements.

Jan 1, 2008

By Hans W. Schreiber

INTRODUCTION At the end of the day, the decision by the sponsor to proceed with a project and to seek financing, or the decision by the financier to grant financing are made on a judgmental basis. Cash flow projections, sensitivity and risk analysis, the innumerable ratios applied by the financier, the so-called feasibility study, etc. are all only tools, and the degree to which they affect decisions is as highly varied as are the personality differences and business conduct and outlooks of the persons who render the decision of "go or no-go". The independent consultant, then, is expected to provide an additional increment of credulity and/or reliability to the "tools" which others will use in reaching a decision; the consultant is really not in a position to directly recommend a "go or no-go". PROJECT FINANCE INGREDIENTS The project finance situation has basically three ingredients: - The project; - The inherent risks attendant with project failure; - The parties. The project, to be viable for financing, will have certain essential characteristics, namely: 1. Clear title or rights to the mineral; 2. Proven definition/establishment of mineral quantity; 3. Financial viability; 4. Physical access consistent with financial viability; 5. A market for the product at a price and for the quantity consistent with financial viability; 6. Transportation/shipping from the project facility to the market at a cost consistent with financial viability; 7. Availability and demonstrated expertise of the developer of the facility; 8. Demonstrated expertise of the operator of the facility; 9. Production processes do not involve unproven new technology; 10. Availability of management personnel; 11. The property and the facilities have value (and thus can be used as collateral); 12. Government approvals/support, as required, will have been obtained; 13. The political environment is essentially friendly and stable; 14. The owner(s) of the project have the financial, strength to make equity contributions consistent with total required investment capital and project risk; 15. Backing by credit support other than that of the financier (i.e. guarantees); The inherent risks of failure are (Nevitt, 2nd Edition); 1. Completion delays with consequent delays in the generation of revenue 2. Cost overruns 3. Technical failure 4. Financial failure of contractors 5. Government interference 6. Uninsured losses 7. Increased price or shortages of raw materials, supplies 8. Technical obsolescence 9. Loss of competitive position in the market place 10. Expropriation 11. Inadequate/poor management The parties directly or indirectly integral to the project financing are: - The mineral rights owner - The developer - The operator - The equity investor

Jan 1, 1985