Search Documents

Vol. 51 has been sent to all members who have paid their 1916 dues. Vols. 52 and 53, the last two volumes for 1916, will be shipped about the middle of-August to all except those owing current dues. Members who do not receive them within a reasonable time are asked to notify the Secretary. Back volumes to complete sets may be purchased from the Institute at reduced rates.

Jan 8, 1916

By Eleanore L. Nestlerode, James R. Guilinger

In April. 1990 Addwest Minerals acquired the Phillips Ranch sulfur property. The sulfur deposit, hosted by the Permian Castile anhydrite, occurs as two distinct elongate. parallel orebodies within a series of northeast-trending grabens. After completing a positive feasibility study, based, in part. on successful drilling programs by Addwest Minerals and previous operators, the decision was made to place the property into production. Utilizing an existing on-site kasch plant, plus significant portions of the recently purchased Texasgulf Comanche Creek Frasch plant. Addwest is currently constructing an 800 long ton per day Frasch mining facility.

Jan 1, 1992

By David Akers, Clifford Raleigh, Glenn Shirey

Under a Cooperative Agreement with the U.S. Department of Energy’s National Energy Technology Laboratory (NETL) and the Mining Industry of the Future Program, CQ Inc. is demonstrating the GranuFlow™ process for improving the recovery of fine-sized coal in commercial coal preparation facilities. The State of Pennsylvania’s Energy Harvest Grant Program is also providing funding for this project. The GranuFlow technology involves the addition of an asphalt emulsion to a slurry of fine-sized coal (<100 mesh or 0.15 mm, typically froth flotation concentrate) before mechanical dewatering in screen-bowl centrifuges. The emulsion selectively agglomerates the carbon-rich particles, resulting in increased particle size and improved recovery of the coal fines during the dewatering process. This paper summarizes the test conditions and current results for both bench-scale investigations and full-scale commercial plant demonstrations.

Jan 1, 2005

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

It appears that Utah is about to add another mining district to its already impressive roster. This time it is the Great Salt Lake, whose high-mineral content waters are being subjected to intensive study aimed toward the recovery of potassium, magnesium and lithium compounds by solar evaporation techniques. Among the firms conducting such experiments is Lithium Corporation of America, which, in a joint venture with West Germany&apos;s Salzdetfurth A.G., is operating evaporating ponds and running engineering tests at a site near Little Mountain, about ten miles west of Ogden. Here, on the clay flats along the northern portion of the lake, LCA holds leases and options totalling about 55,000 acres in the Bear River Basin.

Jan 7, 1966

By R. J. Jewell

The storage capacity of any given tailings storage facility (TSF) is a function of the volume available for the tailings, for which the geometry of the final upper surface of the tailings is most important. One of the advantages that can be obtained from thickening tailings prior to discharge is that the tailings can be stacked at a steeper beach angle than is obtainable with conventional low-density slurries. However, there is at present no universally accepted method available for the accurate prediction of tailings beach slopes. This paper examines the current situation with the objective of putting the quest for a method for the accurate prediction of beach slopes into perspective. The paper references published reviews of the best-known beach slope prediction methods. However, there do not appear to be any independently verified projects or published references to projects on which a Class A prediction has been validated for any of these approaches, and in those instances where projects have been implemented correlation of actual with predicted slopes has been poor - often due to differences between the properties of the tailings assumed in the design and those actually achieved in the field. The author also concludes that flume-scale testing cannot be taken as a reliable indicator of full-scale performance, and suggests that the outcome of any current predictive method should be used by experienced practitioners as only one of a range of indicators in order to suggest a range of slope angles likely to result for any given operation. Practice has shown that it is possible to manipulate beach slopes by changes to the disposal technique, such as limiting the rate of discharge per discharge point and by increasing or decreasing yield stress, but the impact of these changes cannot readily be predicted. There are also newly emerging technologies, such as the injection of a polymer into the tailings at discharge, that will enhance the dewatering of tailings and hence expedite the consolidation of the tailings, that could well facilitate the development of steeper beach slopes. The overall conclusion is that with the current state of knowledge, the accurate prediction of beach slopes is not possible. Furthermore, in view of the inherent variability of the tailings parameters from any operation, it may well be of more value to concentrate on developing an understanding of the means by which the tailings parameters may be manipulated by the operators to achieve a given beach slope than to concentrate wholly on developing a generic beach slope prediction model.

Jan 1, 2012

By S. J. Pearce

The Bureau of Mines has prepared, as circumstances have dictated, a series of Schedules setting forth the minimum requirements that various types of equipment should meet to be considered safe and satisfactory for use in certain hazardous or unhealthful conditions. These Schedules cover a wide variety of devices ranging from explosives to electrically operated mine locomotives. This paper deals with those Bureau of Mines Schedules under which respiratory protective devices are tested and approved, and its purpose is to explain the function and operation of these Schedules. Provisions have been made for testing and approval of the following types of respiratory protective devices: Self-contained breathing apparatus,2/ supplied-air respirators,3/ gas masks,4/ dispersoid respirators,5/ and chemical cartridge respirators.6 These devices are tested at the Central Experiment Station of the Bureau of Mines in Pittsburgh, Pa. Self-contained breathing apparatus is tested by the Safety Branch, and the other types of respirators are tested by the Health Branch.

Jan 1, 1951

By Kenneth L. Reid

The Mineral Resources Research Center at the University of Minnesota has recently installed a QEM*SEM system (Quantitative E.valuation of Materials using Scanning Electron Microscopy) to aid in detailed mineralogical evaluation of potential mineral resource developments in Minnesota and to provide services to the North American mineral industry. A primary application for the unit is to serve the Minnesota taconite industry by providing mineralogical analysis of ores and concentrator products. Minnesota taconite ores contain fine-grained magnetite in a quartz matrix. The ores undergo several size-reduction/magnetic-separation steps to produce a final concentrate with approximately 75% passing 325 mesh and containing about 5% gangue. The paper describes a typical taconite concentrator flowsheet and reports some preliminary results of the applications of QEM*SEM particle image maps and cumulative yield liberation data to samples from selected points in the concentrator circuit.

Jan 1, 1988

By D. L. Yopps

In research conducted by the U.S. Bureau of Mines, platinum-group metal (PGM) flotation concentrate from the Stillwater Complex, MT, was subjected to biooxidation using Thiobacillus ferrooxidans in an effort to break down the sulfide minerals and liberate the associated PGM&apos;s for subsequent chemical leaching. Bacterial preleaching oxidized up to 94 pct of the sulfide present, destroyed the PGM-bearing pentlandite [(Ni,Fe)9S8] mineralization, and dissolved most of the nickel in the concentrate. Cyanidation at 80° C proved to be the most attractive chemical leachant, removing 34 pct of the platinum, 76 pct of the palladium, 94 pct of the rhodium, and 97 pct of the gold from the biooxidized concentrate. Research also indicated that increased sulfide oxidation during the preleach phase led to improved PGM recovery in the subsequent chemical leaching phase.

Jan 1, 2010

By L. Wade, D. R. Pearce

A detailed account is given of the spectral ratio laboratory method for the determination of seismic velocity and attenuation through rock cores under simulated in-situ stress conditions. An account of a computer program called AUTOQ is described for automatic processing of a complete set of laboratory results. Some of these results are shown and discussion is directed to- wards the suitability of in-situ velocity or attenuation measurements in determining rockmass condition or stress regime.

Jan 1, 1996

By N. Mungan

A study was made of the effects of wettability and interfacial tension on the immiscible displacement of a Iiquid by another Iiquid from porous media. The influence of viscosity ratio was also investigated. Porous media used were polytetrafluoroethylene (TFE) cores prepared by compressing TFE powder under different pressures. lt is shown that displacement of a wetting by a nonwetting Iiquid is always less efficient than the displacement of a nonwetting by a wetting fluid, all other things being equal. In the former case, the recovery efficiency can be increased substantially by either reducing the interfacial tension or increasing the viscosity of the displacing fluid. A qualitative discussion is given on the implications of this work to the recovery of crude oil by water flooding. INTRODUCTION The high cost of oil exploration and new recovery schemes makes it imperative that waterflooding be conducted under conditions favoring most efficient oil recovery. To improve oil recovery by waterflooding, it is essential that the role played by interfacial forces in the entrapment of residual oil be studied and understood. Interfacial phenomena in natural rock, connate water and crude oil systems are very complicated because of the complexity of the natural liquids found in petroleum reservoirs, because of our inability to adequately describe the geometrical structure of the porous media and because of a lack of understanding of physical and chemical interactions between the liquids and surface of the pores. The problem becomes further complicated when one tries to elucidate the role of interfacial phenomena in fluid flow. Numerous studies of the displacement of oil by water under different interfacial tension or wet-tability conditions have been made.lm3 These studies have been performed in silica, alundum or sandstone systems using water and paraffin oil and also some surface active material to control the interfacial tension s and the contact angle 0. Unfortunately, the high energies of various interfaces involved favor adsorption and orientation of the surface active material at the interfaces. Also the surface active material concentration at the interfaces exceeds that in the bulk of the liquid phases. Such surface excess may cause the surfactant distribution, the contact angle and the interfacial tension to differ from their measured static equilibrium values and makes interpretation of the displacement experiments difficult. Furthermore, as changes in s also lead to changes in cos 0, the role played individually by one of these parameters in the displacement becomes obscured by the effect of the other. To circumvent these difficulties, a low surface energy solid and true solutions or pure liquids should be used. Use of a low surface energy solid minimizes adsorption and orientation effects at the solid-liquid interfaces. By controlling s and cos 0 through use of selected pairs of pure liquids or true solutions rather than by surfactants, the adsorption effects at liquid-liquid interfaces are eliminated. In the present study TFE cores were used as the porous media. Liquids used were water, sucrose solutions, paraffin oils and benzyl, n-butyl and isobutyl alcohols. The interfacial tension was varied from 40 to 1.1 dynes/cm by suitably choosing the liquid pair. A surface active material was added to the water-oil system only in the case where interfacial tension of 0.5 dyne/ cm was desired. No precise changes of cos 0 were attempted. However, either the displaced or the displacing liquid could be made the one which preferentially wets the TFE surface. Using sucrose solutions and blends of paraffin oils proved to be a convenient way of changing the viscosity ratio between the displaced and displacing liquids. The present investigation examines the effect of interfacial tension, wettability and viscosity ratio on the immiscible liquid-liquid displacement from porous media. Observed data permit a

Jan 1, 1967

By Leonard Sargeant

The Pocahontas Coal Field consists of eight mineable seams of low-volatile coal in southern West Virginia and Virginia. The deeper seams, especially the Pocahontas No. 3 and No.4 Seams, under heavy cover and below drainage are notoriously gassy. Methane in the Pocahontas Field is generally thought of as being confined in the coal itself, rather than in mud slips or clay veins. Furthermore, it is characteristic of Pocahontas coal to retain its gas until the coal is broken and removed from the solid. Because of this inability for gas to escape from unmined coal, entries developed around large blocks are seldom of significant value in bleeding off methane before pillar extraction begins. This is evidenced by the fact that it is not uncommon to find gas liberated during the mining of chain pillars and barriers which have been developed for several years. The Pocahontas Fuel Company develops almost all solid coal by conventional methods with shuttle car haulage. To provide the maximum productive capacity without compromising ventilation and safety requirements, the Company has adopted standards for ventilating 5, 6 and 7-entry sections.

Jan 1, 1960

A regular general meeting of the Canadian Mining Institute will be held in Vancouver, B. C., on Nov. 26-28. The Council extends a cordial invitation to all members of the American Institute of Mining and Metallurgical Engineers to attend.

Jan 11, 1919

By David E. Siskind

The Bureau of Mines has studied the problem of cracking in residential structure walls from vibrations produced by blasting in surface mines. Direct observations were made of blasting damage consisting primarily of cosmetic cracking in plaster and gypsum board walls. Measurements of structure response and also application of the response spectra analysis single-degree-of-freedom model were used to quantify the frequency dependence of the safe level criteria. An overall summary analysis was performed using the new Bureau of Mines damage observations and data obtained from nine previous studies, including the three analyzed earlier by the BuMines for Bulletin 656, published in 1971. Separate analysis of the high- and low-frequency damage cases, structural response, and two types of construction resulted in the establishment of safe vibration levels ranging from 12 mm/sec to 50 mm/sec (0.5 in/sec to 2.0 in/sec).

Jan 1, 1980

By S. J. Baumgartner

The ferromanganese industry is under pressure to deal with the slag arising from the production of ferromanganese, which is discarded in landfills or slag heaps. This material poses an environmental and health risk to surrounding ecosystems and communities, and disposal costs are increasing. Ferromanganese slag contains an appreciable amount of residual manganese metal, which can be exploited. Previous work has shown that the slag can be leached fully, while rejecting the silica to a residue. The methods that were investigated to recover manganese from the leach solution included hydroxide precipitation to upgrade the leach solution followed by manganese carbonate precipitation to produce a pure manganese carbonate product or a manganese carbonate furnace feed material, which would be recycled to increase manganese recoveries in the production of ferromanganese. In addition, electrowinning of electrolytic manganese dioxide from the leach solution was studied. The methods were compared in terms of selectivity, costs, and product quality. Co-recovery of the leach residue, which is a potential cement additive, is discussed. Among the methods investigated to upgrade the pregnant leach solution, hydroxide precipitation utilizing ammonia to adjust the pH appears to be the most effective in removing major impurities such as iron, aluminium, and silica to less than 1 ppm. The manganese carbonate and impure manganese carbonate furnace feed products met quality specifications. However, although the production of these materials was technically viable, the large amounts of base reagent that were required to raise the pH, and the associated high operating costs, rendered the process uneconomic. An optimization study was therefore carried out with the primary objective to determine the ideal acid amount to be utilized in the waterstarved digestion stage, thereby decreasing acid and base consumption while optimizing the quality of the pregnant leach solution, and producing a leach residue that contained <1% Mn. The outcome was an economically viable process. Additional benefits included an increase in the manganese content of the impure manganese carbonate furnace feed material, and a substantial reduction in the dilution of the pregnant leach solution, thereby maintaining high manganese concentrations that rendered the solution viable for electrowinning of electrolytic manganese dioxide, the production of which yielded a current efficiency of 74%.

Jan 1, 2014

By J. Kempken, T. Schreiter, R. Degel, H. Schmieden

After a short summary of the historical milestones of the submerged arc furnace, the paper will highlight different applications and their specific smelting furnace requirements in the non-ferrous area. Additionally, aspects of rectangular furnace design and the features of the copper cooling system for the side wall will be emphasized. Finally a state-of-the-art design tool as well as a new invention to improve slag cleaning technology will be featured, which shows great potentials especially for the PGM and copper related industry. Keywords: submerged arc furnaces, aerro alloys, non-ferrous, copper, slag cleaning, PGM, rectangular furnace, DC technology

Jan 1, 2006

By Sean Gallagher

Study Design. A split-plot experimental design was used to evaluate the influence of posture, trunk angle, and rotational velocity on peak torque output and myoelectric activity during maximal trunk extension maneuvers. Objectives. To determine whether the kneeling posture alters extension torque capabilities in isometric and isokinetic exercises as compared with standing. Also, to ascertain whether recruitment of trunk muscles is modified by such a postural change. Summary of Background Data. Factors such as workplace geometry may force workers to adopt awkward or unusual postures in the performance of manual tasks. An understanding of the limitations placed on strength in unconventional working postures is crucial to the proper design of jobs. Methods. Twenty-one healthy male subjects (mean age = 36 years 7 SD) performed 12 trunk extension exertions in standing and kneeling postures. Isometric tests were performed at 22.5°. 45°, and 67.5° of trunk flexion. isokinetic tests were done at three velocities: 30°/sec, 60°/sec, and 90°/sec. Electromyographic data were collected from eight trunk muscles to assess muscle recruitment under each condition. A prior; orthogonal contrasts were specified for analysis of both torque and electromyographic data. Results. The kneeling posture was associated with a 15% decrease in peak torque output when contrasted with standing; however, no concomitant change in trunk muscle activity was evident. Trunk hyperflexion (isometric tests) and increasing rotational velocity (isokinetic tests) were associated with reduced torque in both postures. Trunk muscle activity was primarily affected by changes in trunk angle and velocity of contraction. Conclusions. A reduced extensor capability exists in the kneeling posture, despite equivalent trunk muscle activity. The similar activation patterns in both postures suggest that the strength deficit does not result from alterations in trunk muscle function. Rather, it may be the consequence of a reduced capability to rotate the pelvis in the kneeling posture, due to a disruption of the biornechanical linkage of the leg structures. [Key words: electromyography, isokinetic, isometric, low back pain, posture. strength1 Spine 1997;22:1864-1872

By N. Standish

Heat transfer coefficients have been measured in beds of various packings irrigated with mercury and molten fusible alloy countercurrent to hot gases. The measured coefficients for both systems were found to increase with gas velocities and liquid rates. Correlations were determined which show this dependence and also indicate that heat transfer in these systems is influenced by the liquid flow characteristics and the thermal conductivity of the gas and the solid packings. A heat transfer model has beer2 proposed which explains the various features of the experimental results. On the basis of this study, which gives an insight into the heat exchange in the melting zone of the blast furnace, it was concluded that by comparison with the furnace stack heat transfer coefficients are about 1.5 times higher in the melting zone. EACH year large tonnages of metal are produced in operations which, in part, involve liquid metal irrigation of "packings" countercurrent to hot gases. The melting zone in blast furnaces and in cupolas is a good example of packings irrigated with a liquid melt countercurrent to gases. In all instances of this kind large amounts of heat are exchanged and it is desirable to have some knowledge of heat transfer phenomena involved in these systems. So far the most common method of analyzing furnace efficiencies, fuel requirements, and the general thermal state of the furnace has been through the use of heat balances. As heat balances are essentially statements of the first law of thermodynamics they give no real indication of the factors which govern heat transfer between phases in the various zones of blast furnaces. Hence, rational improvement in production efficiency and the development of theoretical models is only possible if the heat transfer characteristics are known at every stage of the process and related to the important variables involved. This has been generally recognized for some time but it was only recently that Kitaev et al.&apos; have produced a comprehensive treatment of heat transfer in solid-gas countercurrent systems such as the blast furnace stack and the packed bed regenerator. Using their treatment it is now possible to predict the effect of particle size, thermal conductivity, bed porosity, and the flow rates of both the gas and the solid material on the heat transfer in the blast furnace stack. However, the stack of a blast furnace is only one part of an integral unit for which the heat transfer analysis cannot be complete without also considering the heat exchange in the melting zone. The complexity of heat transfer processes in this region of the furnace has so far escaped quantitative description. Yet, the melting zone accounts for a greater amount of heat exchange than all the other zones of the furnace put together. Moreover, if the reduction of oxides in the melting zone proceeds in part in the liquid state the importance of heat transfer on furnace productivity and on the metal and slag temperatures is obvious. THEORY Heat transfer for two-phase flow in packed beds is a complex problem involving a number of heat exchange paths for which interphase areas are not known with any degree of certainty. Analytical solution is, therefore, difficult. This difficulty is emphasized by noting that Rabinovich~ and Luck have only recently solved the steady-state heat transfer for simplified two-phase heat exchangers of known area. However, useful progress can be made for the system considered by making a not unreasonable assumption that the usual heat transfer considerations apply and restricting treatment to the steady state. For these conditions the rate of heat transfer dq in a height dz of a packed bed of unit area is: dq = UaATdz [I.] Integration of Eq. [I] then gives the total heat transferred: assuming both U, the overall heat transfer coefficient, and a, the interphase area, to be independent of bed height. Since a, in these systems, is unknown it is convenient to combine this term with U. The group U, then represents the overall heat transfer coefficient on a volumetric basis. If AT is linear with q, then for a bed of unit volume Eq. [Z] can be integrated to give: is the log mean of terminal temperature differences. From Eq. [3] U, can be readily calculated as q and {AT)im are experimentally obtained quantities, but a difficulty arises in interpreting its meaning. Two approaches are possible depending on whether the effect of packing in the transfer of heat is neglected or not. If the packing is thermally decoupled then the resistance concept gives the relationship: which states that the overall resistance is the sum of the gas phase and the liquid phase resistances (assuming areas are equal throughout). Because the resistance to heat transfer in liquid metals is negligible by comparison with that of the gas,4 Eq. [4] can be simplified, i.e.:

Jan 1, 1969

By Wei Tu

A grade separation was required to allow uninterrupted traffic crossing for a busy rail spur and a county road. The grade separation was achieved by creating a 30-foot (9-meter) high embankment that incorporates two multiplate tunnels and allows the passage of a rail spur and an existing county road. The site is located in an abandoned meander channel in the floodplain of the Mississippi River, near Osceola, Arkansas, and is underlain by more than 40 feet (12 meters) of soft clay and interlayered clays, sands and silts. Without soil improvement, the post-construction settlement would exceed 3 feet, slowly crushing the proposed tunnel structure and cutting off the railroad. Preloading, combined with vertical drains, was used to accelerate the consolidation of the underlying soil layers and to reduce the post-construction settlement under working loads. Six settlement plates were installed to monitor the progress of consolidation under surcharge load. The Asaoka observational method and the hyperbolic fitting method were used to analyze the measured settlement data to predict the end of primary settlement. The in-situ consolidation coefficient, ch, was back calculated from the measured settlement data. The stress release caused by the removal of the preloading surcharge load and the tunnel installation was determined using a Plaxis 3-D finite element model. The measured and predicted settlement using Hansbo&apos;s analytical solution demonstrated reasonable agreement. Early removal of the surcharge and construction of the tunnel prior to reaching the end of primary settlement was accomplished by analyzing the post-excavation stress reduction achieved via tunnel construction.

Jan 1, 2009

Jan 1, 1949