Search Documents

By J. D. Ramsdell

The purpose of this investigation was to determine the effects of the impurities, oxygen, nitrogen, carbon, and iron (in low percentages) on the mechanical properties of electrolytic titanium. The strength and hardness of binary Ti-O, Ti-N, and Ti-C alloys are linear functions of alloy content in the composition range investigated. Compared to oxygen and carbon, nitro-gen is the most effective strengthener and hardener, followed by oxygen, then carbon. When the carbon concentration is above 0.10 percent, carbides are present, and strength and hardness are relatively unchanged. For equivalent hardness levels, Ti-Fe alloys are stronger than binary titanium alloys containing oxygen, nitrogen, or carbon. However, the strengthening is related to the presence of transformed beta in the structure.

Jan 1, 1960

By John E. Lens

Driving bridge foundation piles into glacio-fluvial sands and gravels and glacial tills brought surprisingly longer than predicted driving lengths on several recent projects in Vermont. In some instances, piles drove more than 40 feet past refusal depths predicted from Standard Penetration Resistances from borings terminating in glacial till. Overall, piles developed substantially less skin friction than predicted using common capacity formulas and drove as much as 80 feet longer than predicted in the moderate to dense gravelly and cobbly soils. These piles were driven for one to five span highway bridges within narrow valleys with bedrock ranging from 80 to over 200 feet deep. Piles were for both conventional and integral abutment bridges. H-piles were used for a variety of reasons including lower unit cost, better availability, and better ability to drive through cobbly soils in upper strata. Dynamic testing was used to evaluate capacity, including skin friction and end bearing capacity. In order to develop better pile length and capacity predictions for future projects, VTrans and one of their geotechnical consultants are collaborating to develop criteria for improved pile capacity predictions in these river valleys. We are doing this by evaluating driving and dynamic testing data from four projects in comparison with the Federal Highway Administration (FHWA) DRIVEN pile design software, and methods from Myerhof (1976) and Tomlinson (1981). Our overall objective is to provide a basis for choosing appropriate pile types and reliably estimating pile lengths for projects in this terrain. Bridge foundation design projects in other mountainous terrain share similar design and construction challenges to those encountered in these Vermont projects. These include: difficult exploration drill rig access requiring smaller rigs with limited capability to drill through cobbles and boulders deep enough to reach bedrock; limited experience with displacement piles as alternatives to H-piles in this geology; and relatively greater variability in soil stratigraphy between foundations at these sites as a consequence of the relatively high energy depositional environment in mountainous terrain. This paper presents the case history summaries of the pile driving, results of the ?back analysis? capacity evaluations, examples of solutions employed on these projects to address the lower capacities achieved, and resulting pile capacity design guidelines and prediction criteria for these geologic conditions based on data from these projects.

Jan 1, 2007

By William H. Dresher

The crust of the earth, together with its seas and its atmosphere, is the source of all of mankind's primary wealth. Indeed, most people think of precious metals and stones when they think of wealth mined from the earth, but the value of the material and energy goods derived from the earth far exceed the value of the precious metals and gem stones. Thus, it is obvious that all minerals which we mine from the ground represent new wealth--the copper, clay, or petroleum we mine just as much as the gold or silver. More and more, wealth is defined in terms of utility-not in terms of an arbitrarily established monetary value. The recent action of the OPEC nations in controlling the flow of petroleum has clearly demonstrated this to the petroleum-importing nations! There is developing in the United States, as well as in many other nations of the world, a concern for the future availability of many mineral-derived raw materials and of mineral fuels. Ore grades are diminishing, concern for the environment has placed restraints on commercial development of some mineral deposits and the processing facilities necessary to exploit them, and countries upon which we have relied for major mineral materials have become increasingly nationalistic, causing uncertainties in future supply and causing an increasingly alarming deficit in our nation's balance in trade.

Jan 1, 1980

By F. T. Paleari

Radial gas holdup profiles have been measured in a 50x400 cm flotation column using a multi-cell conductivity probe. Three different bubble generation systems were examined: up to eight vertical filter cloth spargers, three horizontal filter cloth spargers, and three (horizontal) Cominco-type spargers. The variables tested were: number of spargers, symmetry of their arrangement, and height above spargers. Batch water with up to 20ppm frother concentration was used. The general observation is that the profiles tend to be uniform (i.e. flat) with some exhibiting a slight wavy shape. The vertical sparger arrangement proved the most difficult to achieve profile symmetry. The horizontal spargers gave uniform profiles at right angle to their length but a decreasing gas holdup along their length; the Cominco-type spargers gave slightly less scatter in the data. Switching off selected spargers (to simulate malfunction) did not produce strong asymmetry in the profiles.

Jan 1, 1993

By W. G. Fischer

This paper attempts to close the gap between extensive rock testing with field measurements and the mine operator's need for safe mine layouts and alternatives. It was found that many of the variables that influence mine geometry and worker safety are relatively unimportant while others are critical. The development of empirical relationships that tie the critical variables to the safe useful life of a trona mine layout and observations made in 140 production areas where the variables were researched over a 15-year period are discussed. The concepts presented may have applicability in mine design for other bedded deposits.

Jan 1, 1986

By Roscoe C. Clark

A study of the effect of various corrosive waters on five different types of cements indicated that those cements containing less than 5 per cent tricalcium aluminate were the most resistant to corrosion. INTRODUCTION Oil field experience indicates that some formation waters are excessively corrosive to some cements. A study has been made to determine the most corrosive waters and the relative resistance of various types of cement to these corrosive waters. PROCEDURE This study of the corrosion of cement was limited to an evaluation of the effect of various corrosive waters on five different types of cements. A determination was made of the types of cements which offer the greatest resistance to corrosion and of the chemical contents of waters found to be the most destructive to cements. The laboratory tests were conducted by immersing small cylinders of 20 samples of set cement in various corrosive waters. The initial mixing of most of the cement slurries was done using Tulsa tap water as the mixing water; however, a few of the slurries were mixed using a sulfate water as the mixing water. When the 20 samples had been immersed for a period of nine months, they were removed from their corrosive baths, inspected and photographed. The field tests were conducted by placing ten cement specimens, each contained in a screen wire thimble, in the gas anchors of insert pumps in wells in six different fields. The specimens were observed whenever it was necessary to pull the pumps and were returned to the 1aboratory when deterioration had reached a serious state. EXPERIMENTAL RESULTS In both the field and laboratory tests the resistance of the different cements to corrosion was determined by the condition of the samples and the number of samples of each that were in good condition at the end of the immersion period. Table I lists the various cements tested in the order of their resistance to corrosion with the most resistant at the top and the least resistance at the bottom. An analysis of Table I reveals that the upper half of the table predominates in slow set and sulphate resisting cement.: (low 3CAO.A12O3 content) while in the lower half the port-land and high early strength cements are in the majority. Of the last two the high early strength cements appear to offer less resistance to sulfate water corrosion. An investigation of the composition of the cements listed in Table I indicated that as a general rule the cements containing less than five per cent tricalcium aluminate will exhibit the greatest resistance to corrosion. The destructive action of various corrosive waters was compared by listing the waters in the order of those containing the largest number of samples that failed completely. These ratings are presented in Table II with the most corrosive waters listed first and the least corrosive last. Figs. 1 and 2 show the end views of cement samples which had been immersed in the baths of five per cent MgSO, water and the five per cent Na2SO4 water respectively in the laboratory. These .pictures are representative of the results obtained and present a pictorial evaluation of the corrosive resistance of various types of cements.

Jan 1, 1950

By Charles W. Kenney

Mercury contamination of soil at an old chemical plant surrounded by a residential community and adjacent to a river has provided unique challenges for the current owner. Inorganic and organic mercury compounds had accumulated over the past 50 years to levels that require remediation. Hazen Research, Inc. conducted a multi-phased program to characterize contaminants and their occurrences, evaluate various treatment technologies, and demonstrate the selected technology at bench and pilot scales. A combined physical cleaning and chemical treatment was demonstrated to meet treatment goals for the site. This paper discusses the methods of process selection and results of the bench-and pilot-scale testing.

Jan 1, 2003

By William Morales

De acuerdo a su diversidad biológica, la pila de la lixiviación de La Quinua es única en su género, por lo que es importante la clasificación de los diferentes frentes de minado. Posteriormente, de acuerdo al avance de explotación fue cambiando las características del mineral, facilitando la descarga directo a la pila de lixiviación. Sin embargo, la presencia de finos, arcillas y la poca profundidad de remoción del mineral, perjudicó la extracción de oro, orginando un incremento de inventario de oro en la pila de lixiviación. En este sentido, el presente texto describe los contínuos cambios del mineral y sus características, originando un cambio en el método de lixiviación a través del cambio de los controles operacionales de altura de banco y flujo de riego, en respuesta de pruebas metalúrgicas que se desarrollaron con el tipo de mineral.

Sep 12, 2011

By B. K. Parekh

The International Symposium on Comminution was organized at Camborne School of Mines, Cornwall England. Papers covered the fundamental and practical aspects of comminution in the mineral industry. Although comminution equipment design has not changed fundamentally during the last 50 years, methods of control and optimization have improved considerably. A simulation model for batch ball milling in the rotating mill was developed as a step toward continuous simulation of ball and autogenous milling. New concepts in jaw crusher technology design and the concept of a 1.6- x 2.1-m (66- x 84- in) jaw crusher with open feed throat has resulted in power savings. The use of cone crusher technology in comminution circuits with particular reference to machine design, plant flowsheet and control figuration has been reported by Boliden Allis, of Sweden. The Whiten steady state crusher model form has been used to develop a quantitative model of 2.1-m (7-ft) cone crushers. This was done by incorporating liner age (wear) and liner length as variables on the selection of particles for breakage and thus on the product size distribution. Another paper by Lira and Karetsky discussed the development of a model based on a multisegment ball mill developed by Whiten and Kavetsky. It is capable of simulating the performance of a coarse grinding ball mill of a given diameter, ball size and mill speed.

Jan 1, 1991

By P. Kerr

Iron segregation is pre-dated by copper and nickel segregation processes for which the experimental methodology and reaction chemistry were established. The accepted reaction sequence for segregation involves the generation of hydrogen chloride, the chloridization and volatilization of the metal chloride, and precipitation of the metal from the metal chloride in the vicinity of carbon. Iron segregation roasting offers a potential extraction solution for processing oxide deposits with complex mineralogy or waste streams such as Minette-type iron deposits, nickel laterites, ilmenite, red mud, electric arc furnace (EAF) dust, mill scale and slag. After subsequent magnetic separation, one is left with a high grade metallic iron powder which can be marketed for powder metallurgy or briquetted to serve as a direct reduced iron (DRI) product. The non-magnetic product is typically concentrated oxides including rutile, alumina, or oxides of V, P, and rare earths, etc. that may be economically recoverable with subsequent processing. While operating conditions vary for different metals, they share the requirements of an elevated operating temperature and a mixture of oxide ore, carbonaceous additive and a chloride additive in varying amounts all in a closed reactor to allow for reducing conditions and contain the volatile chlorides. This process is then followed by some form of physical separation. Testwork performed by the authors shows promising results that may aid in future development of the process. Segregation roasting of iron will likely never displace traditional beneficiation and ironmaking technologies; however, it has great potential in niche markets where traditional technologies have failed or current technologies generate substantial waste.

By Haipeng Li, Jacob Masliyah, Barun Gorain, Jian Huang, Qingxia Liu, Zhenghe Xu, AuTec Innovative Extractive Solutions Ltd.

"Froth flotation is widely used to selectively separate one or more minerals from an ore over a wide range of particle sizes with high efficiency. Bubble–particle attachment is one of the most critical steps in flotation. The objective of this project is to demonstrate the need for an innovative dual bubble generator to improve flotation efficiency. This dual bubble generator was designed to generate two different sizes (micron size and typical flotation size) bubbles. The micron size bubbles generated on the crevices of particle surfaces in venturi type of cavitation tubes enhanced the attachment of fine particles to the bubbles in conventional flotation systems. They also acted as a secondary collector, which has the potential to reduce operation cost and improve flotation recovery. The dual bubble generator was evaluated for a double refractory gold ore with 3g/t Au, 1.5 wt% TCM (total carbonaceous matter) and 0.7 wt% sulfides. The results were compared with those obtained using a commercial bubble generator. Compared with the commercial bubble generator, the dual bubble generator showed not only a higher gold recovery, but also an improved separation efficiency, demonstrating the potential of dual bubble generator in fine particle flotation.INTRODUCTIONFroth flotation has been widely used in mineral processing and waste water treatment. However, flotation has been proven inefficient for fine particle recovery although it becomes increasingly inevitable to process fine particles with the depletion of easy processing ores. The critical problem of fine particle flotation is the low attachment of fine particles to flotation size bubbles due to their low collision rate. Based on a commonly acceptable flotation model given by R =F*[Pc*Pa*(1-Pd)], the probability of bubble–particle collision (Pc), attachment (Pa) and particles detachment from air bubbles (Pd) collectively determines fine particle recovery (R) (Yoon and Luttrell, 1986). Since Pc = (3Dp/Db) where Dp and Db are diameters of particles and bubbles, respectively, bubble size and particle size impact the bubble-particle collision in opposite directions. It is evident that the probability of bubble–particle collision decreases with decreasing the size of particles, leading to a low recovery of fine particles. In this case, reducing the bubble size and/or increasing the apparent size of particles by fine particle aggregation are clear means to improve fine particle recovery."

Jan 1, 2016

By D. Van Orden, Y. Kamiya, R. Lee, E. Ilgren

Crocidolite is a well-known causative agent for mesothelioma. However, studies have shown that the pathogenicity of the fiber from different mines varies considerably and it has been postulated the parameter that appears most likely to account for this variation is fiber width although this has never been formally confirmed. To date, crocidolite appears to be the only asbestos mineral for which an epidemiological study comparing the risk of mesothelioma in a population exposed to ‘thin’ fibers with another exposed to ‘thick’ fibers of the same species may be carried out. Finnish anthophyllite, South African amosite, and African Transvaal crocidolite can also be classified as thick fibers, and there is a paucity of mesotheliomas in populations exposed to them compared to those exposed to thin Cape crocidolite. No thin occurrences of these minerals are known. Our previous study looked at crocidolite from several sources. The present study considers the amphibole anthophyllite found in many places in the world. This mineral, regardless of source, does not show the same variation in fiber width found with crocidolite from different areas. All anthophyllite fibers that have been mined may be classified as thick and populations exposed show very low levels of mesothelioma. We suggest the most likely explanation is related to the fiber width distribution and a concomitant reduction in the ‘Stanton fiber size’ fraction.

Jan 1, 2012

By Y. Houbaert, L. Kestens, R. Decocker

"A magneto-elastic model is presented to calculate the orientation dependence of the magnetostrictive strain, observed at saturated magnetisation in ferromagnetic materials with a cubic crystal structure and an arbitrary crystallographic texture. The formula of Becker and Doring is used to express the anisotropy of magnetostriction for a single crystal. In order to simulate the macroscopic average magnetostriction of a polycrystalline aggregate (with an arbitrary texture) the Reuss assumption of the elasticity theory was applied. According to this assumption the various orientations of the polycrystal can defonn without constraints, producing local strain incompatibilities in the microstructure but observing total stress equilibrium. The macroscopic strain is calculated as the weighted average of the individual strains of all orientations composing the polycrystal. The weight factors are determined by the volume fractions of the corresponding orientations of the given texture, which can be measured by standard X-ray diffraction techniques. The model is applied to simulate the variation of magnetostriction (at saturation) with respect to the rolling direction for a standard grade of Goss-oriented electrical steel. A brief comparison with experimental data allows validating the basic model assumptions. IntroductionBecause of tougher environmental constraints, the noise reduction in transformer cores has become increasingly important. It is generally accepted that the main source of noise is magnetostriction, which is known to be caused during the magnetisation process by the movement of 90° magnetic domain walls and the rotation of the magnetisation vector out of the easy directions. Therefore, it is obvious that when a ferromagnetic body is magnetised to saturation, the resulting magnetostriction will be dependent on the distribution of magnetic domains in the initial state.In the literature two coefficients are used to describe the resulting magnetostriction at a saturating magnetic field. The total strain, measured from an arbitrary demagnetised state to technical saturation, is called the saturation magnetostriction, and is denoted by (~)s. The tenn magnetostriction coefficient will be employed to designate the strain measured from the ideal demagnetised state (i.e. one in which no preferred orientation of domains exists) to technical saturation. Failure to recognise the difference between these two quantities has led to considerable confusion in the literature.The magnetostriction coefficient for a single crystal is a well-known property for ferromagnetic cubic materials. In 1939 Becker and Doring [1] have derived the following relation, describing the magnetostriction coefficient for single crystals with a cubic symmetry:"

Jan 1, 2001

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By J. M. Harrison

"The Nor-Acme gold mine is near the shore of Snow lake, northern Manitoba, about 75 miles east of Flin Flon. The claims that form the nucleus of the present property were staked in 1927 by C. R. Parres, but it was not until 1941 that diamond drilling disclosed the potentialities of the deposit. In that year a large-scale drilling programme was begun under the direction of F. Ebbutt, of the Howe Sound Exploration and Development Company. Two orebodies were outlined containing about 5,000,000 tons of ore assaying $5.25 in gold per ton. In August, 1945, construction of the mining plant was begun.All information and interpretations contained in the following brief description of the deposit were obtained from surface mapping.GEOLOGYThe ore lies at the contact between a coarse, basic, pyroclastic rock, which is the hanging-wall, and grey, acidic lavas and sediments, which form the footwall. These rocks are cut by irregular basic intrusions that vary in composition from diorite to hornblendite, and by small acidic dykes . Tourmaline is locally common in the hanging-wall rock near the ore.The ore occurs in brecciated, silicified, and ·slightly carbonatized rock. Arsenopyrite is the main sulphide and the gold is associated with it. Pyrrhotite is locally abundant and minor pyrite, chalcopyrite, sphalerite, galena, and cubanite have been noted. Two orebodies are known, the Dick and the Toots. The Toots, which is much the smaller of the two, is about 1,000 feet west of the Dick."

Jan 1, 1954

By W. T. Abel

Laboratory tests were conducted with a closed, recycling system to evaluate the effectiveness of solid-in-gas suspensions as heat transport mediums. Micronized graphite in helium or nitrogen was circulated by a centrifugal compressor to determine the feasibility of the method and heat transfer capabilities of the mediums. Suspensions were circulated without plugging or eroding the compressor or piping. At low flowrates and light (0.1 to 0.2 volume-percent) graphite loadings, slightly less power was required to transport a given amount of heat with suspensions than with helium alone. Graphite deposition on the heat exchange surfaces of the cooler decreased the heat transfer effectiveness at higher solids concentration. Efforts to eliminate deposition are described.

Jan 1, 1963

By Arthur E. Wells

"The present and possible future commercial production of potash from various sources in the United Status is discussed below under the following heads:1. Potash from the saline lakes.(a) Nebraska lakes.(b) California lakes.(c) Other lakes.2. Potash as by-product from the cement kilns.3. Potash as by-product from the iron blast furnace.4. Potash from silicate rocks.(a) Feldspathic material.(b) Leucite rocks of Wyoming..(c) Sericite slates of Georgia.(d) Glauconite (greensand) of New Jersey.5. Potash from Alunite.6. Potash from organic sources other than kelp.7. Potash from kelp.In this discussion very little more than passing reference, if any, will be given to those projects which up to date have been developed only slightly, if at all, beyond the small scale laboratory stage, or for the development of which there appears to be very little financial and technical backing at the present time. Nether or not many of these proposed projects have merit can be determined only by an actual operating demonstration.Generally speaking, the potash industry of the United States has been hardly more than marking time since the armistice. This is, largely due to the fact that the consumers of potash have been expecting that heavy shipments of foreign potash to the United States would be resumed soon at somewhere near the pre-war prices, and they have not seen owing domestic potash at present prices for many months. The result has been that domestic producers have been unable to sell their product at even cost and many producers of potash have been obliged to close down. Thu Nebraska lake plants were closed down in February. The California saline plants were operating at below capacity, and the only large alunite plant is closed down. Even the cement plants have little or no inducements to recover the potash being lost in their waste gases and the production is very small at present.This condition will doubtless continue until a definite policy is decided upon as to the future importation of potash salts from Germany and. France. If unrestricted importation is allowed at prices even 50% greater than in 1913, only a very few, if any, of the domestic projects will be in position to compete with the foreign potash immediately, and the present industry will probably greatly decline with little or no prospect for a future resumption of the industry."

Aug 1, 1919

By H. C. Fiedler

X HE development of the cube-on edge secondary re-crystallization texture in Si-Fe strip requires that normal grain growth be restrained. It has been shown that the degree of restraint and hence the completeness of secondary recrystallization depends upon the size and number of second-phase particles, which in turn is dependent upon the prior processing history.1y2 The purpose of this note is to show that, for heats in which manganese sulfide particles are providing the restraint to grain growth, the choice of hot rolling temperature depends upon the manganese content. The making and processing of the heats to the final gage of 0.012 in. has been described.3 The compositions are given in Table I. Apparent in Fig. 1 is the decrease in the ability of strips hot-rolled from 1175°C to undergo secondary recrystallization as the manganese content increases. It has been shown that 1175°C is below the solubility temperature of 0.014 pet S in even the 0.038 pct Mn alloy: and the observed behavior is attributed to an increasing fraction of the sulfur forming large manganese sulfide particles at the heating temperature for hot rolling. This fraction of the sulfur is thus unavailable to subsequently form the small, uniformly dispersed particles which are needed to restrain normal grain growth. Since the sulfur is completely in solution at 1325°C,3 strips from all three alloys show strong secondary recrystallization behavior when hot-rolled from that temperature.

Jan 1, 1969

By Walter Harvey Weed

AMONG the many causes of that perplexing feature of mine-exploitation, the unequal distribution of the ore, the influence of the country-rock upon the vein-contents has long been accepted as an important factor in certain districts, but the general application of the theory has not been proved. It is now possible to obtain trustworthy data with which to test the theory, and either to confirm or to overthrow this time-honored tradition. By the searching methods of modern petrography and chemistry, rock-determinations are now scientifically made, while the examination of thin sections of ores supplements field- and laboratory-study, and affords conclusive evidence of the paragenesis of the ore-minerals. In the great mass of data regarding mineral deposits accumulated during the past century, there are some facts which stand the test as to reliability; but the greater part are not available for use in this discussion. Within the last 20 years, however, many able workers have contributed careful and accurate accounts of various ore-deposits; and it is by the facts given in such papers, and by personal experience, that. I have become convinced that there is in some districts a true relation between the country-rock and the mineral contents of the veins. My own interest in the subject arose from the observation of a number of striking instances of the variation of vein-contents with the nature of the inclosing rock. Having already recorded certain observations of this kind, I venture to present in this paper further notes, together with a few facts from the literature of the subject, which seem to prove the correctness of my view. It is apparent that if the relation holds true, though in limited districts only, it will be of great practical in-

Jan 1, 1913

By W. L. Cornell

The processing of lead tailings for removal of the heavy metals produces concentrates upgraded in Co and Ni values. Reflected light microscopy, scanning electron microscopy, image analysis, and Vickers hardness measurements were used to identify mineral species, associations, degree of liberation, and distributions to the test products. Siegenite and bravoite were the most common species encountered, but violarite and enriched pyrite and marcasite phases were also identified. Liberation for the Co and Ni minerals contained in the tailings was 20 micrometers or less.

Jan 1, 1993