Search Documents

By Louis P. Gignac

The Lac Shortt gold deposit is located in Northwestern Quebec, at some 115 km west of the Opemiska Division and 380 km northeast of the Lac Dufault Division, as shown on Figure 1. Falconbridge's exploration crews drilled the first six holes in the gold-bearing ore zone in 1979. After further diamond drilling from surface in 1980, the decision was taken to carry out an underground exploration program. A three-compartment shaft was sunk to a depth of 340 metres in 1981 and 1982; it was followed by an extensive exploration program, which included 1073 metres of cross-cutting and footwall drifting, 645 metres of ore drifting and 11 200 metres of diamond drilling. The underground work was completed by mid-winter 1983. It was followed by a complete feasibility study of the Lac Shortt Project. After some $Can 14.2 millions in exploration expenditures, the Board of Directors of Corp. Falconbridge Copper approved in July 1983 additional expenditures of $Can 45 millions to bring the Lac Shortt Mine in production at the capacity of 261 000 tonnes per year. Gold price was $US 425 per ounce at the time.

Jan 1, 1985

Jan 1, 1908

By Joseph W. Mullan

The today status of air pollution control legislation and regulations can best be described as an exaggerated state of environmental limbo. The '70's began but one and one-half months ago yet it already has been very appropriately named "the decade of the environment." This certainly will be the decade for new legislation - new regulations and hopefully "Clean Air." Already Washington is faced with legislators playing "pollution politics" to the crowds. Students have redirected their efforts from Vietnam to the cleansing of the environment and everyone including the man on the street has become an environ¬mental expert. This is the decade we all face, but where are we today? Pollution is not a new problem. It has been with us for centuries and while much is left to be done, much has already been accomplished. I will try to make some comparisons of what I believe to be the good and bad points in the national air pollution control picture and hopefully will generate within each of you sufficient concern as to which comparisons are sound.

Jan 1, 1970

By A. I. Johnson

This paper describes," the application, of a modular or building block approach to the analysis, design, and control of complex mineral treating processes. The main purpose of the paper is tutorial, to show the reader how such processes can be modeled using a modern digital computer" and, not to discuss in any detail the results that may be achieved in such studies. It is proposed that, the main techniques be illustrated by reference mainly to the Bayer process for alumina extraction and purification; in cooperation with the Aluminum Company of Canada Ltd. the author and his Colleagues at McMaster University and their students have studied this, process as a means of applying new computer techniques to extractive metallurgical processes. The plant described was studied by the author and his colleagues as a senior undergraduate project in cooperation with the Aluminum Company of Canada. It is one of several studies that have been carried out with Canadian industry. (1)

Jan 1, 1972

By James R. Means, George Bowser

A new phone system was developed that provides eight full duplex communications channels over a single twisted shielded phone line, with no central switching station or line amplifiers. This system greatly simplifies installation and maintenance over that required with conventional switching systems. The system is based on microprocessor technology and digital frequency synthesis. Frequency division multiplexing is used over a bandwidth of approximately 300 kHz, and a baseband voice channel (compatible with conventional pager phones) is provided as a backup to assure communication if the multiplex features fail. Multiplex operations are controlled over a 30-kHz digital channel. The system is designed to operate with up to 16 km (10 miles) of cable plant and a maximum phone separation of 8 km (5 miles). The digital techniques permit a limited amount of monitoring and control capability to each phone. This consists of two pair of contact inputs or outputs, to be used as desired. These "flags" may be read or controlled by a dispatcher's phone.

By Roger K. McLimans

Sphalerite in the ores is multi-banded. Based on color and textures, bands in samples separated by a few kilometers may be correlated. Darkness of color is directly related to iron content. Isotopic and fluid inclusion data indicate that temperatures of ore deposition were 225°C-50°C. The agreement between these two sets of data suggests that chemical and isotopic equilibrium were established. The salt content and hydrogen and oxygen isotopic compositions are similar to present-day values of oil field brines suggesting a similar mode of origin. Ore transport and deposition are not adequately explained by either chloride or bisulfide complexing. Necessarily, other mechanisms were involved.

Jan 1, 1979

By Thomas W. Wälde

BACKGROUND Foreign investment has been a major factor in bringing about the substantial mining industries of Chile, Peru, Bolivia, Venezuela, Brasil and Guyana. But economic nationalism and sentiment against foreiqn domination of vital national industries grew in the 1960s and most major mining projects were transferred into state owner ship. Among the state mining enterprises formed were CODELCO - Chile, MINERO-PERU/ CENTRCMIN - Peru, CCMIBOL - Bolivia (in 1952), Hierro-PERU, GUY-BAU/BIDCO - Guyana, etc. New investment during that time was discouraged because it was subject to the restrictive conditions of the investment regulations of the Andean-Pact, a grouping of Chile, Bolivia, Peru, Ecuador, Venezuela and Colombia. The philisophy was that mineral resources were to be developed exclusively by national enterprises. Essential foreign inputs had to be acquired "depackaged" as separate purchases of equipment and technical assistance services. As a result of the worldwide economic recession which hit the mining industries in 1980-1982, many projects that were viable in 1970 were not developed by the new state enterprises due to lack of capital, managerial and technical abilities and due to problems with marketing. As a consequence of the long-term decline of metal prices, governments experienced difficulty in getting investment organized through national or foreign enterprises and have had to face up to the trade-offs between national control and active mineral development. A change has since taken place in governmental policies. The 1981 Peruvian mining law, the 1982 mining law of Uruguay, the 1979/1980 mineral promotion laws of Argentina, all witness the gradual shifting of emphasis from restriction to promotion. The investment rules of the Andean Pact have been progressively softened through national regulation and today are more or less irrelevant. Nationalizations and forced renegotiations have not occurred in the last few years. Countries have gone to great lengths (without much success) to re-attract foreign investment on terms that accommodate the political sensitivities of the South American countries and the practical requirements of investors and financiers. For this analysis, three contracts have been selected which reflect this accommodation in three South American countries, where miner a1 production plays a major role in the national economy. These con tracts reflect both the attitudes and traditions of the individual countries, but also mark the shift in mineral investment policies that has taken place. EL INDIO AGREEMENT The 1977 investment agreement between Chile and St. Joe Minerals marked a dramatic relationship between Chile and foreign mining investor s. In Chile, mining of copper has played a major role in the country's history. Large scale copper mining was initiated and developed by Kennecott and Anaconda. The nationalization of these two companies under the Allende government in July 1971 started a wave of nationalizations of foreign-held mining and petroleum operations since then in many parts of the world. The military government supported the new Chilean state mining companies ((30DELCO and ENMI) , but it also attempted to accelerate mineral development by prom ting foreign private investment, thus reversing the nationalistic policies followed by the Allende and the preceding Frei government. The new policy by the military government is expressed in Decreto-Ley 600 (1974) which governs foreign investment in Chile. Decreto-Ley 600 is

Jan 1, 1985

By John A. Church

THE Lake Superior blast-furnaces probably represent the maximum economy of fuel possible in this country. They smelt an ore which is very rich and easily reducible, and as the small amount of gangue present is not all silica, but in part a silicate, the amount of limestone required is a minimum. The average yield of the ore treated at six furnaces was 63 per cent., and the average quantity of limestone 179 pounds per ton of pig. The fuel used is charcoal, so burned as to retain most of the combustible volatile part, which, before the utilization of furnace-gas, was burned away. With these conditions it is not surprising that the Lake Superior charcoal practice is extraordinary in almost every respect. In any scientific discussion of American furnace work, the establishments there will be found at the head of the list, and they work under conditions which are extremely favorable for careful study. The Bay Furnace, near Marquette, has the honor of carrying "the broom" for the largest daily make. With a capacity of 1908 cubic feet it has, for months together, produced 29 tons of pig, graded at

Jan 1, 1876

By A E. C Peres, P R. M Viana

The role of flotation columns in comparison with conventional mechanical flotation cells is discussed under the scenario of Brazilian flotation technology. All iron ore concentrator circuits commissioned since 1990 incorporated column only flotation technology in rougher, cleaner, scavenger configuration. Columns were also added to existing circuits, especially at the cleaner stage. Columns were also incorporated to phosphate ore flotation circuits operating mechanical cells. In two phosphate concentrators, columns substituted for all mechanical cells. Columns perform the cleaning stage in a large sulfide copper concentrator, following rougher flotation in tank cells. Scavenger of the cleaner tailings is performed in tank cells at this plant. Other ores that are concentrated in flotation columns include graphite, talc, lead-zinc sulfide, and a zinc hydrometallurgical residue for silver recovery.

Jan 1, 2005

By J. E. Gould, H. J. Hand

Many independent studies are being made on slag-metal relationships in the open-hearth furnace, and these studies cannot help but result in an ultimate improvement in the quality of open-hearth steel of both the open and killed types. In maintaining quality control at the National Tube Company's plant, emphasis has been placed on an evaluation of the iron oxide content of the steel in as quantitative a manner as possible, in order that the most desirable level of oxidation might be obtained for a given type of steel, and to secure a more precise basis for final de-oxidation. In the past, various methods were used for estimating FeO content of the metal at tap to ensure uniform and thorough deoxidation of killed steel, avoiding overdeoxidation to minimize the amount of inclusions present and to make as sound a steel as possible. For the open-type steels, such control involves obtaining the necessary level of oxidation for the most suitable action of the steel in the molds to provide good surface quality and cross section for the specific grade involved. While rapid analytical methods are available for determination of FeO in the liquid metal, such methods are still not sufficiently rapid for routine control on the open-hearth floor, nor do such analyses provide information as to what causes high or low FeO values. The method of sampling can still be considered a problem in view of the variability encountered in taking simultaneous duplicate tests. With the accurate rapid methods now available for determining carbon in the metal, estimating slag basicity and obtaining temperatures of liquid metal, it was believed possible to determine the influence of the various furnace reactions in establishiug the state of oxidation at a given time. Simultaneous slag and metal tests were used in this analysis, aided by statistical methods, to determine the factors that affect the metal FeO, and also to make a quantitative evaluation of these factors. Data obtained are from actual iurnace operations, the metal test being of the I spoon, Herty type, and taken in duplicate. Metal temperatures were taken with the open-tube bath pyrometer developed by the Research Laboratory of the United States I Steel Corporation. This method of taking open-hearth metal temperature was invented by Collins and Oseland,l and was developed into its present form by L. 0. Sordahl,2 of the Research Laboratory. The instrument and its mode of operation have been fully described by Sordahl and Sosman in three publications.3,4,5 lag components were obtained by chemical analysis. Data were taken from four 165-net-ton furnaces during the working period of the heat. Recognizing that additions of ore affect the metal FeO. no tests were included within 30 min. after ore additions. In all, 65 tests (48 heats) were used in this study.

Jan 1, 1942

By Y. Huang, P. B. Prangnell

"An Al-0.1Mg alloy was firstly deformed at room temperature by ECAE to a true strain of 10, where a steady state deformation was established and further processing had little effect on grain refinement. The ECAE samples, with an average grain size of ~0.55µm, were then compressed in a channel die at 77K- 473K to various reductions. Microstructures were characterized by electron backscatter imaging and EBSD in a FEGSEM. Grain refinement to the ECAE submicron structure occurred during deformation at cryogenic temperatures of 77 – 213K, whereas coarsening took place during deformation at elevated temperatures. A steady state deformation was observed at all temperatures where a constant grain structure was developed and maintained upon further straining due to dynamic recovery. The mechanisms of dynamic recovery during steady state deformation at cryogenic temperatures are discussed.IntroductionSevere deformation processing (SDP) has been successfully used to produce submicron grain structures, and in some cases nano-scale crystallite sizes, in a wide range of alloys. However, the rate of grain refinement becomes increasingly inefficient at high strains as a steady state grain structure is approached [1-3]. Steady-state grain sizes have also been reported in other ultra-high strain deformation processes, like cryogenic ball-milling [4]. There is thus a minimum grain size achievable in a material by a given SPD process under constant deformation conditions.It is well documented that a steady state subgrain size is observed in warm deformation of metals due to dynamic recovery (e.g. [5]). In severely deformed alloys a constant grain size at ultra-high strains has similarly been attributed to dynamic recovery [1-3]. Mechanisms have been proposed, for rapid deformation induced grain growth including stress driven boundary migration and breakaway from solute pinning [2]. However, as pointed out by Humphreys et al. [2] the restoration processes are currently poorly understood, particularly at low temperatures, where the boundary migration rates required to maintain a constant grain size are orders of magnitude higher than can be satisfactory explained from diffusion controlled migration. Similar to the subgrain size, the steady state grain size obtained during SDP is generally related to the temperature compensated strain rate [2, 6]. Thermally activated restoration processes are thus expected to be suppressed by lowering the deformation temperature and a smaller steady state grain size can be achieved."

Jan 1, 2012

By Alten F. Grandt

What is prime farmland? Can such land, once it has been surface mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on surface mined land in St. Clair County (Grandt, 1949). This research was done almost thirty years before requirements of Public Law 95-87 were passed by the US Congress and signed August 3, 1977.

Jan 1, 1982

By C. H. Ma, J. S. Makris

This paper describes a modified X-ray diffraction microscope wzethod based on the general principles of Berg-Bawett's Method, Lang's Method, and Woosters1 Technique. This new method may be used for stationary or oscillatory photomacrographs, with both reflection and transmission techniques. In the stationary technique, a small point-source of a divergent X-ray beam of white radiation is used; in the oscillatory technique, a monochromatic divergent beam is employed. The chief advantages of the method described herein are that only approximate alignment of the Bragg angle -of-interest is needed during exposure, and that a large portion of a crystal-specimen surface can he irradiated. In recent years, the study of dislocations through X-ray diffraction microscope techniques has received considerable attention as concerns the per,fection of single crystals. Very promising results have appeared in the literature.'-' These techniques are very useful when the dislocation density of a crystal is near 105 per sq cm or lower. The principle of X-ray diffraction microscopy is based on the differential effect of X-ray primary extinction between the distorted parts and the perfect parts of a crystal. When an X-ray beam impinges on a set of planes of a crystal at the correct Bragg angle, diffraction of X-rays will occur with a 90-deg phase shift of the diffracted beam. This once-diffracted beam still forms the correct Bragg angle with the planes ahead of it, if the planes are not distorted. Thus, part of the strength of the once-diffracted beam is rediffracted and the beam continues to travel in the direction of the primary X-ray beam. This twice-diffracted beam not only takes away part of the strength of the once-diffracted beam, but also causes destructive interference with the primary beam because it now is exactly 180 deg out of phase with the primary beam. As the primary beam goes farther and farther into the crystal, its intensity is continuously weakened. Asa result, the ultimate X-ray diffraction power of a set of undistorted planes is largely extinguished. This phenomenon is called primary extinction.1,2'4 If the set of planes ahead of it is distorted, the once-diffracted beam will have less chance to be rediffracted, because it could not meet the exactly correct Bragg angle for rediffraction. If a part of the beam does rediffract, this twice-diffracted beam is not exactly 180 deg out of phase with the primary beam, and thus it causes less destructive interference. As a result, the registered X-ray diffraction power of the distorted part of a crystal appears stronger than that of the perfect part. Thus, point-by-point contrast of a diffraction image is theoretically possible from a crystal containing dislocations. Two most popular X-ray diffraction microscope techniques today are Berg-Barrett's Method and Lang's Method. Both of these techniques require a

Jan 1, 1964

M. A. SCHEIL (presented in written form).-Messrs. Franks, Binder and Brown are to be congratulated for the splendid paper that they have presented. We have not made stress-corrosion tests with the cantilever type of specimen which they describe, but it is well known that a uniform stress across a certain portion of the gage length can be obtained with such a specimen. This type of specimen would appear quite expensive to make. The writer was interested in the authors' remarks concerning the erratic results obtained from specimens with cold sheared edges. It might be of general interest to record here some results we obtained with annealed sheet N4 in. thick of type 304 stainless steel. After specimen No. 4 had been exposed 65 days without any signs of cracking we applied a strain gage and measured the stress as 25,810 psi. This value is considerably higher than we find for some of the type 347 stainless alloys and suggests that 18-8 might have a different threshold value for stress-corrosion cracking than 18-8 columbium. The test data in Table I show that strain caused by cold work or polishing has a pronounced effect in lowering the time for failure. In my paper I showed values of 8 hr. and 17 hr. to stress crack cold-rolled type 301 stainless steel stressed beyond the yield point. This steel contained 8.31

Jan 1, 1945

By Howard G. Coopersmith

Kelsey Lake kimberlites are a cluster of eight diamondiferous pipes that occur in the northern State Line kimber lite district of the Colorado-Wyo¬ming diamond province (Coopersmith 1991, 1993) (Fig. 1). This is located at the southern margin of the Wyoming Archean province. Two relatively large pipes and a few smaller bodies define the cluster (Fig. 2). The Kelsey Lake kimberlite cluster has been developed as the first diamond mine in the United States. The cluster was discovered in 1987. Full-scale production began in the spring of 1996. Mining has produced gem-quality diamonds up to 28.3 carats in size. The 30 State Line kimberlites, intruded about 390 million years ago into Proterozoic crystalline rocks, were presumed to be underlain by Archean basement of the Wyoming Province. Nearly all the kimberlite pipes contain diamond but only the Kelsey Lake pipes are economic. The Kelsey Lake kimberlites contain predominately diatreme facies kimberlite, with minor hypabyssal and crater facies rocks locally occurring. Alteration and weathering of the kimberlites is extensive. Petrologic studies indicated an underlying lithosphere that has a largely Proterozoic signature and shows evidence of deep melt and metasomatic events. Current development has concentrated on the two largest pipes. These have been bulk-sampled after geological study (1987) identified the presence of small diamonds and mineral chemistry indicating favorable diamond conditions. A 10-t/hr (11-stph) rotary pan plant was established in 1992 to process thousands of tons of bulk-sample material. Grades and gem-quality diamonds to 14.2 carats in size were recovered. Early in 1995, it was decided to move from evaluation to commercial mining. Production began in early 1996. A 195-t/hr (215-stph) rotary pan plant was built. A water supply system and tailings disposal have also been incorporated. The project straddles the Colorado/Wyoming border. Existing mining permits were amended to incorporate the increased scale and new plant facility. The permits for this project included the following: Colorado mining permit, Wyoming dozing permit, Corps of Engineers Section 404, Colorado NPDES, Wyoming NPDES, Storm water Management Plan, Air Pollution Emission Notice, various Colorado and Wyoming State Engineer and well permits, Substitute Water Sup¬ply Plan, Larimer County Special Use Review, and US Forest Service road use permits. The temporary destruction of a wetlands area was a sensitive issue. It has been addressed through the Clean Water Act Section 404 permit administered by the US Corps of Engineers. This use will be mitigated by creating new, self-sustaining wetlands in the immediate drainage system. A comprehensive and bonded reclamation plan is incorporated in the permits. Diamond mining and ore processing is environmentally benign. No chemicals are used in processing the diamonds. The plant is a water wash facility. The kimberlite ore is inert, as is the granite wall rock. The exposure of the ore body and the subsequent ore processing and waste rock and tailings containments pose no threat of release, leaching or dispersion of any detrimental elements. There is no acid-forming waste. Even a prolonged acid rain environment will not produce a harmful leachate. Slimes containment and clarification ponds will prevent unacceptable levels of suspended solids in water discharge. The isolated, restricted access and nonvisible nature of the mine and processing has led to straightforward permitting. Geology The State Line district is located in the northern

Jan 1, 1997

By Raymond Hofstetter, Paul Worsey

The purpose of this paper is to investigate commonly used methods for mitigating the effects of shrapnel from linear shape charges (LSC) used in the demolition industry. Primarily the problem is not that shrapnel poses a threat to human bystanders, but rather it can affect the other charges in the demolition or damage to structures in close proximity to the charges. This research aims to determine what methods have success at stopping shrapnel, what methods do not, and to promote an awareness of the dangers of using the LSC without any protection. The project was carried out at the Experimental Mine site at the Missouri University of Science and Technology. This research is an undergraduate research project to fulfill the requirements for the Explosives Engineering minor program at MST.

Jan 1, 2008

By J. D. Ramsdell

The purpose of this investigation was to determine the effects of the impurities, oxygen, nitrogen, carbon, and iron (in low percentages) on the mechanical properties of electrolytic titanium. The strength and hardness of binary Ti-O, Ti-N, and Ti-C alloys are linear functions of alloy content in the composition range investigated. Compared to oxygen and carbon, nitro-gen is the most effective strengthener and hardener, followed by oxygen, then carbon. When the carbon concentration is above 0.10 percent, carbides are present, and strength and hardness are relatively unchanged. For equivalent hardness levels, Ti-Fe alloys are stronger than binary titanium alloys containing oxygen, nitrogen, or carbon. However, the strengthening is related to the presence of transformed beta in the structure.

Jan 1, 1960

By John E. Lens

Driving bridge foundation piles into glacio-fluvial sands and gravels and glacial tills brought surprisingly longer than predicted driving lengths on several recent projects in Vermont. In some instances, piles drove more than 40 feet past refusal depths predicted from Standard Penetration Resistances from borings terminating in glacial till. Overall, piles developed substantially less skin friction than predicted using common capacity formulas and drove as much as 80 feet longer than predicted in the moderate to dense gravelly and cobbly soils. These piles were driven for one to five span highway bridges within narrow valleys with bedrock ranging from 80 to over 200 feet deep. Piles were for both conventional and integral abutment bridges. H-piles were used for a variety of reasons including lower unit cost, better availability, and better ability to drive through cobbly soils in upper strata. Dynamic testing was used to evaluate capacity, including skin friction and end bearing capacity. In order to develop better pile length and capacity predictions for future projects, VTrans and one of their geotechnical consultants are collaborating to develop criteria for improved pile capacity predictions in these river valleys. We are doing this by evaluating driving and dynamic testing data from four projects in comparison with the Federal Highway Administration (FHWA) DRIVEN pile design software, and methods from Myerhof (1976) and Tomlinson (1981). Our overall objective is to provide a basis for choosing appropriate pile types and reliably estimating pile lengths for projects in this terrain. Bridge foundation design projects in other mountainous terrain share similar design and construction challenges to those encountered in these Vermont projects. These include: difficult exploration drill rig access requiring smaller rigs with limited capability to drill through cobbles and boulders deep enough to reach bedrock; limited experience with displacement piles as alternatives to H-piles in this geology; and relatively greater variability in soil stratigraphy between foundations at these sites as a consequence of the relatively high energy depositional environment in mountainous terrain. This paper presents the case history summaries of the pile driving, results of the ?back analysis? capacity evaluations, examples of solutions employed on these projects to address the lower capacities achieved, and resulting pile capacity design guidelines and prediction criteria for these geologic conditions based on data from these projects.

Jan 1, 2007

By William H. Dresher

The crust of the earth, together with its seas and its atmosphere, is the source of all of mankind's primary wealth. Indeed, most people think of precious metals and stones when they think of wealth mined from the earth, but the value of the material and energy goods derived from the earth far exceed the value of the precious metals and gem stones. Thus, it is obvious that all minerals which we mine from the ground represent new wealth--the copper, clay, or petroleum we mine just as much as the gold or silver. More and more, wealth is defined in terms of utility-not in terms of an arbitrarily established monetary value. The recent action of the OPEC nations in controlling the flow of petroleum has clearly demonstrated this to the petroleum-importing nations! There is developing in the United States, as well as in many other nations of the world, a concern for the future availability of many mineral-derived raw materials and of mineral fuels. Ore grades are diminishing, concern for the environment has placed restraints on commercial development of some mineral deposits and the processing facilities necessary to exploit them, and countries upon which we have relied for major mineral materials have become increasingly nationalistic, causing uncertainties in future supply and causing an increasingly alarming deficit in our nation's balance in trade.

Jan 1, 1980

By F. T. Paleari

Radial gas holdup profiles have been measured in a 50x400 cm flotation column using a multi-cell conductivity probe. Three different bubble generation systems were examined: up to eight vertical filter cloth spargers, three horizontal filter cloth spargers, and three (horizontal) Cominco-type spargers. The variables tested were: number of spargers, symmetry of their arrangement, and height above spargers. Batch water with up to 20ppm frother concentration was used. The general observation is that the profiles tend to be uniform (i.e. flat) with some exhibiting a slight wavy shape. The vertical sparger arrangement proved the most difficult to achieve profile symmetry. The horizontal spargers gave uniform profiles at right angle to their length but a decreasing gas holdup along their length; the Cominco-type spargers gave slightly less scatter in the data. Switching off selected spargers (to simulate malfunction) did not produce strong asymmetry in the profiles.

Jan 1, 1993