Search Documents

By Debra W. Struhsacker, Jean Kiel, Jeffrey Thatcher

3.1 INTRODUCTION As heap leach precious metal projects become increasingly common in the United States, federal, state and local regulatory agencies are beginning to take a closer look at the short- and long-term environmental consequences of this recovery technology. From an operator's point of view, there is seemingly a confusing regulatory maze to be navigated and a plethora of permits and approvals to be obtained prior to commissioning a heap leach operation. The degree of difficulty associated with obtaining permits for a heap leach project depends largely upon the state in which the project is located. Permit acquisition is generally easiest in those states most familiar with heap leaching technology. For example, heap leaching is well understood in Nevada, and heap leach operations are relatively easy to permit, although permitting conditions in Nevada have recently become more stringent. However, many states are just beginning to become familiar with heap leach operations. Many of these states such as Idaho, Colorado, South Dakota, Oregon, Montana, Washington and South Carolina are in the process of drafting regulations and establishing guidelines for heap leach projects. In most cases, these regulations specify design and operating criteria as well as reclamation and decommissioning procedures. This chapter provides an overview of the regulatory and permitting aspects of heap leach operations. Permitting requirements for projects developed on federal land are discussed in detail. 'The state and local regulatory atmosphere and permitting requirements for various states are also presented. The chapter concludes with a generic permitting strategy. 3.2 KEY ENVIRONMENTAL CONCERNS The primary concern of most local, state, and federal regulatory agencies is the use, storage and transport of sodium cyanide (NaCn), and potential cyanide contamination of surface and groundwater resources. The toxicity of cyanide to people, fish and wildlife is also an important issue. Unfortunately, in the public eye, cyanide heap leaching has some emotional impacts similar to those associated with radioactivity and uranium mining. This perception and the general lack of understanding of cyanide can lead to unnecessary concern about cyanide contamination, further complicating the regulatory environment.

Jan 1, 1988

By R. W. Metsger

The metamorphic zinc-iron-manganese ore in the Grenvillian rocks of the Reading Prong m Sussex County, N.J. is unique. The singularity of its mineral composition and associations has fueled controversy among economic geologists and mineralogists for more than a hundred years. The silicate-oxide ore, in two synformal concentrations has been mined since about 1838. The Franklin mine was depleted in 1954, while the one at Sterling Hill is still producing. Although the two mines are perhaps best known for their almost three hundred mineral species and have been a mecca for collectors, they -- as importantly -- have provided a window through which to observe more than a billion years of geologic history. When pieced together, studies reveal a sequence of probable sedimentary deposition, intense folding, pseudo- viscous flow with attendant negative diapirism, uplifting, erosion, karstification, hydrothermal alteration, burial, faulting, igneous intrusion, uplift , saprolitization, and glaciation.

Jan 1, 1985

By A. M. Ozbayoglu

Gross calorific value (GCV) of coals was estimated using artificial neural networks, linear and non-linear regression techniques. Proximate and ultimate analysis results were collected for 187 different coal samples. Different input data sets were compared, such as both proximate and ultimate analysis data, and only proximate analysis data and only ultimate analysis data. It was observed that the best results were obtained when both proximate analysis and ultimate analysis results were used for estimating the gross calorific value. When the performance of artificial neural networks and regression analysis techniques were compared, it was observed that both artificial neural networks and regression techniques were promisingly accurate in estimating gross calorific values. In general, most of the models estimated the gross calorific value within ±3% of the expected value.

Sep 1, 2012

By A Llewellyn, M Varvari

The ventilation circuit at the FrogÆs Leg Mine was originally designed to permit mining to progress down to 440 m below surface at a maximum production rate of 500 kt/a, as per the feasibility study. The FrogÆs Leg resource has now been defined down to 640 m below surface at a maximum production rate of 750 kt/a. In order to allow for this increase in production depth and tonnage, it was necessary to upgrade the ventilation circuit.This paper outlines the upgrades to the ventilation circuit that were undertaken and the underlying rationale behind them.CITATION:Llewellyn, A and Varvari, M, 2013. Ventilation upgrade at the FrogÆs Leg Mine - Case study, in Proceedings The Australian Mine Ventilation Conference , pp 95-102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By E. G. Leonardon

The question of geophysical prospecting is one that is beginning to occupy a pre-eminent place in the minds of those actively concerned in the discovery and exploitation of ore deposits. This is in marked contrast to the reception accorded such ideas when the Junior author, six and a half years ago, began introducing electrical prospectii1g to the mining fraternity on this continent. Happily, the mention of geophysics no longer evokes the sceptical and pitying smiles that it did in those days. A little reflection will show that modern geophysical methods are merely a logical development from pre-existing technique. In the study of geological problems, is it not logical to use all possible physical properties of matter? The study of crystal form and cleavage, the examination of thin sections of minerals by means of polarized light or ordinary light, in fact, utilize physical properties of minerals for the benefit of the geologist. These are, of course, laboratory methods, and the extension of the study of similar properties into field work was inevitable. This began with the magnetometric surveys, used as early as 1760 in New Jersey to locate iron ores. Eighty-four years later, John Locke's work in the United States resulted in pointing out relationships between the terrestrial magnetic field and main tectonic features of the earth's crust.

Jan 1, 1928

By M. Sakamoto, S. Karaswa, Y. Yoneoka, Y. Ohmizo

"The Annaka Refinery has been processing leach residue by Waelz process for 17 years. Recently, the quantity of the leach residue has increased due to a decline in the quality ~f zinc concentrate. Meanwhile, negative factors (e.g. deterioration of water balance due to improved electrolytic power consumption rate) have increased· in the processing of the leach residue.We have implemented various measures in responses to this situation, while striving to increase ·processing capacity and achieve stable operation. AS we have largely completed our assessment of the efficacy of these measures, we report on our recent process improvements.IntroductionWe have been treating leach residue by the Waelz kiln process since 1981. At that time, treatment of only 50,000 tons of leach residue per year was anticipated. However, subsequent process improvements have revised this figure up to 75,000 to 80,000 tons per year.However, today's increased Fe zinc concentrate grade has resulted in increased amounts of leach residue. In addition, improvements have reduced electrolytic power consumption rate of zinc electrolysis, limiting the amount of water that can be used in ·the zinc refining processes and for deaning leach residue. Consequently, we encounter an increasing number of problems and factors adversely affecting leach residue treatment, including increases in water-soluble Zn (WsZn) and. S (S04) in leach residue.To solve these problems, we have taken several measures to ensure long-term continuous operation and treatment of this increased · amount of leach residue. This paper discusses these measures."

Jan 1, 2000

By Charles Pretorius, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge.

Jan 1, 2006

By D. R. Forshey

Although the United States has the world's largest coal reserves, most of those reserves will require underground mining. Unless underground injury and fatality rates are reduced, the number of disabling injuries and accidental deaths will grow as coal production increases. The Bureau's Mining Research Program, designed to reduce the exposure of workers to hazards while improving productivity, is described. Major program thrusts are 1) re- moving the hazards or removing miners from the areas in which hazards exist, 2) developing ways to improve management decisions and mining skills so as to reduce the incidence of situations requiring human involvement in hazardous, emergency, or corrective tasks, and 3) improving, or at least maintaining, productivity so that both the tangible (dollar) and intangible (human) costs are reduced. In these ways, projected demands for coal can be met using resources without an increase in human suffering.

Jan 1, 1987

By J. E. Friant, R. P. H. Willis, J. Maaren

Considerable effort is currently directed towards the development of non-explosive mining methods with the potential to allow continuous mining in narrow reef conditions. Besides improving productivity, continuous mining results in concentrated mining which has a significant impact on reducing infrastructure costs. CSIR: Miningtek recognized the potential of mini-disc cutters in a long or short wall application for selective hard rock mining in 1999. EEA was chartered to build a 780 mm diameter by 800 mm deep drum cutter head. While EEA designed and built the head, CSIR designed and built the drive mechanism and chassis for the trial machine. After assembly and shop testing at CSIR’s facility, the machine was shipped to a platinum mine for trials. This paper traces the development of mini-disc cutters and their application in South Africa.

Sep 1, 2001

By M. H. Weinecke, B. P. Faulkner

This paper will discuss the process for making lightweight aggregate, the waste materials that make good lightweight aggregate, the chemistry of making lightweight aggregate and finally a discussion of the commercial prospects for making lightweight aggregate from wastes. Svedala Industries has been making lightweight aggregate (LWA) from waste materials for the last ten years. Many clay-like materials, such as coal-fired boiler ash and washings from a granite quarry, can be used alone or with additional waste materials to produce a commercially saleable LWA.

Jan 1, 2001

By C. A. Allen

"The problem of signaling to the hoisting engineer from a moving cage in the shaft has been considered by many mine operators for a number of years. There are several methods in use in different mining districts, and so far as the writer is aware they have been further developed in Utah than in any other state. The latest installations are of interest because they use a very low-voltage circuit for the shaft wires and also because the wiring can be so arranged that the hoist can be stopped from the cage, if so desired.The first installation in Utah was in the shaft of the Centennial-Eureka mine under the management of C. E. Allen. It was placed in operation in the summer of 1899, end has been in continuous and satisfactory operation for 21 years. The arrangement consists or two bare wires down the shaft carrying a current at 60 volts potential, with a device on the cage for making connection between the two wires. This device is simply a short piece of wire which is thoroughly insulated from the cage and is operated by a short lever. Whenever the cage rider wishes to signal the engineer he pulls down the lever, forcing the short wire out against the two bare wires, thus making a circuit which rings the bell in the hoist-room. A similar device was planned in the Grand Central shaft at Mammoth, Utah, but was later abandoned. The cause of failure was reported to be that the shaft was very wet."

Jun 1, 1920

By Richard C. Travis, Edward C. Dowling

A detailed kinetic study of the flotation installation at the Metcalf Concentrator revealed a rougher flotation circuit operating under less than optimal conditions. Based on these results, a project was initiated to approximately double the rougher flotation capacity by increasing the installed volume from 780 cubic meters to 1,560 cubic meters. This project, which was completed in early 1991, replaced the existing cells with larger capacity cells. A comprehensive analysis of results demonstrates significant metallurgical benefits. INTRODUCTION/BACKGROUND The Metcalf Concentrator is located in Morenci, Arizona and is part of Phelps Dodge Morenci, Incorporated. Sumitomo Metal Mining of Arizona is a minority partner in the operation with 15% interest. The Metcalf Concentrator is the newer and smaller concentrator and operates in conjunction with the Morenci Concentrator. Operating capacity at Metcalf is currently 48,000 TPD of ore on a 365 days per year basis. The Metcalf Concentrator was commissioned in 1974 at a 30,000 TPD operating rate for the purpose of treating ores originating in the Metcalf Mine. The mine takes its name from the former town of Metcalf which was named for Robert Metcalf who was credited with discovery of the mineral district. The predominant ore mineral is chalcocite which occurs as a secondary enrichment closely associated with iron pyrite. The host rock is largely granodiorite and quartz monzonite. The original rougher flotation circuit consisted of a total of six rows of Wemco 8.5 cu. meter (300 cu.ft.) flotation machines treating pulp from the two grinding sections (Sections A and B). Each row was configured in a 4-4-4 arrangement. Shortly after startup the throughput rate was increased significantly without sustaining a recovery loss. This increase was achieved by raising the target value for the particle size of the cyclone overflow which is the rougher flotation feed. Shortly thereafter, the capacity of the pump and cyclone began to restrict further increases in throughput. After testing, two 66 cm. (26-in.) cyclones and a 12-in. X 12-in. centrifugal pump replaced the original classification equipment. As a result of these modifications, the grinding section could routinely process in excess of 42,000 TPD. Due to the increased tonnage rates, limitations in the rougher flotation circuit performance were observed. In an effort to improve the performance of rougher flotation with this higher throughput, the speed of the flotation mechanisms was increased from 230 RPM to 250 RPM. This change improved the suspension of the coarser feed and induced additional air into the pulp. It did, however, apply additional strain to the motors, shortening their life. At these elevated processing rates, it was found that the dart valves operated almost entirely at the top end of the control range and could not efficiently handle upsets from the grinding section. This was remedied by lowering the end overflow weir and allowing some of the tailings to overflow the end weir. However, in order to obtain acceptable recovery levels, the flotation pulp was maintained at a high level, adversely influencing the rougher concentrate grade.

Jan 1, 1993

By Helen Morrison, Chris Staun, James Vaughan

"Mercury is introduced into the Bayer refining process as a trace element in bauxite. During the digestion stage, a portion of the mercury is extracted which partitions between the flash tank off-gas, vapour condensate and bauxite residue streams. A technology or treatment that stabilises mercury in the solid phase during digestion would prevent environmental management issues that may arise from the presence of mercury in condensate and non-condensable gases. This study examines the effect of process additives on the deportment of mercury under Bayer digestion conditions. Bauxite digestion experiments were conducted in batch autoclaves in the presence of additives. Process liquor was analysed for mercury content using a thermal desorption technique. Pyrite and copper hydroxide were evaluated for their suitability as additives.INTRODUCTIONMercury is an ancient metal characterised by electrochemical nobility, volatility, low solubility in water and a liquid state at room temperature (Holleman and Wiberg, 2001). The biogeochemical cycle of mercury is complex. Elemental mercury may enter the atmosphere due its volatility, where it can be transported long distances. After settling and adsorption to sediments, methylation is catalysed through microbial metabolism (Qureshi et al., 2009). Methylated mercury species are potent neurotoxins, and bioaccumulation of mercury is well documented, particularly in seafood (Kozin et al., 2013, Pan et al., 2014, Pollman, 2014). Environmental regulations for mercury emissions are becoming increasingly stringent (UNEP, 2015). Considerable research has already been performed and technologies developed for the remediation of mercury in wastewater and the trapping of mercury from industrial stack emissions. Wastewater technologies usually target ionised mercury using adsorbent, ion exchange and complexation mechanisms (Krishnan and Anirudhan, 2002, Li et al., 2015a, Chiarle et al., 2000), while stack emission technology is dominated by impregnated activated carbon adsorbents (Gao et al., 2013, Zheng et al., 2012). Related developments include piezoelectric amalgamating sensors for in line detection of gaseous elemental mercury in industrial stack emissions (Kabir et al., 2015, Sabri et al., 2011). There is a paucity of research regarding removal of mercury from the Bayer process."

Jan 1, 2016

By R. G. Meara, O&apos

The land-pebble district of Florida, which in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of Sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of limey or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the rushing and formerly lost supplied the feed.

Jan 1, 1931

By J. Bal, V. D. Dao, W. Li

"SynopsisThis study proposes a methodology for evaluating the risk of coal bumps in multiple-seam longwall mining. Both the stress field and the total energy release (TER) during retreat were evaluated in the specified case involving multiple-seam mining using the LaModel program. The results of numerical simulations indicated that both the peak vertical stresses on the panel edges and the peak TERs in the outby longwalls increased significantly as the horizontal offsets were reduced from 60 m to zero. With the comprehensive consideration of the stress field and TERs, a conservative offset of 60 m was ultimately adopted when developing the gateroads of the lower panel in the field. The field measurements indicated that coal bumps were avoided completely by employing the proposed design, and the maximum roof-to-floor and rib-to-rib convergences of the tailgate during retreat were only 360 mm and 576 mm, respectively.IntroductionCoal bumps – sudden, violent bursts of coal – pose a serious threat to the safe excavation of coal. Their occurrence depends on the properties of the surrounding rocks, stress field, and dynamic disturbance. The complexity of the mechanism of coal bumps is further enhanced in multiple-seam mining due to seam interaction. Multiple-seam mining is most frequently found in the coalfields in eastern China, such as Xuzhou, Xinwen, Zaozhuang, and Huainan. In the past, due to issues of availability, economics, and ignorance of the potential risk in multipleseam mining, coal seams in such conditions were mined without proper planning to account for seam interaction. Fortunately, studies published over the past three decades have raised awareness of the problems associated with multiple-seam mining, and indicated that the ground control issues induced by multiple-seam mining can be avoided and/or minimized with proper planning.A number of technical studies pertaining to the design of multiple-seam mines have been published. These studies can be divided into two groups based on their methodologies of design: empirical (Chekan and Listak, 1993; Haycocks and Zhou, 1990, Matetic et al.; 1987a, 1987b) and numerical approaches (Li et al., 2000; Maleki, 2007; Mark, 2007; Peng, 2007; Zipf, 2005). The majority of the extant studies on the interaction mechanisms in multiple-seam mining have focused on the load transfer during operation, resulting in the proposal of the pressure bulb theory (Forrest et al., 1987; Haycocks and Karmis, 1983; Peng, 2008; Peng and Chandra, 1980) and pressure arch theory (Holland, 1973; Oram and Ponder, 1997) to guide multiple-seam mine design. However, neither, of these theories can be used to evaluate the potential for coal bumps."

Jan 1, 2015

By B A. Wake, G G. Lowder, M J. White

The Tooloom gold field is located within the New England Fold Belt in the far northeast of New South Wales, approximately 130 km south southwest of Brisbane. Gold was first discovered at Tooloom in 1857. Within a few years up to 10 000 people were mining placer gold deposits in the Tooloom valley and a few tried their hand at mining hard rock occurrences as well. Mining of alluvial gold continued in a small way at Tooloom until very recently, but only in the last few years, since Malachite Resources acquired its interest at Tooloom (now 100 per cent), has the full potential of this large, reduced intrusion-related gold field been appreciated. By the mid 1870s, once the alluvials were largely worked out, most of the early miners had made the 270 km trek north to the newly discovered Gympie gold field and Tooloom slipped into obscurity. Such was this obscurity that the Tooloom gold field was not recorded on published Government geological maps until 2001, four years after Malachite became involved. The many hard rock prospects that Malachite has identified in recent years were largely or completely unknown. Tooloom is a good example of blinkered thinking when it comes to modern mineral exploration. The New England province in NSW has long been the æpoor relationÆ to the much better known and more highly favoured Lachlan Fold Belt in NSW. It has also suffered serious neglect compared with the Queensland part of the New England Fold Belt that hosts such major gold deposits as Mt Morgan (>7 Moz), Gympie (>3 Moz) and Cracow (>1 Moz). Tooloom is proof that prospective geology does not stop at state borders.

Jan 1, 2004

By G. Montgomery

This is a summary of what has happened to the domestic production of two industrial minerals vital to a healthy US economy: fluorspar and barite. A few years ago we were self-sufficient in both minerals and good ore reserves still exist. FLUORSPAR Some 9% of the fluorspar presently being consumed in the US is imported, whereas the use of fluorspar has not declined proportionately. Several factors can be mentioned.

Jan 1, 1986

By Juliana Parreira

The past decade shows record increases in global demand for minerals and metals with an accompanying significant decline in skilled personnel. Mining companies today are examining new technologies to maximize production, reduce costs, and create safer work conditions to deal with this shortfall. Automation of an open-pit mine haulage system is receiving attention as a beneficial option since it provides more consistent and efficient operation of mining equipment, it removes workers from potential danger, it reduces fuel consumption significantly reducing greenhouse gas (GHG) emissions, and it can help optimize vehicle repairs and equipment replacement because of more-predictable and better-controlled maintenance. This paper describes a simulation model under development using the EXTENDSIM software package to examine scale-up issues and constraints of autonomous vehicles in comparison to a manual system. The software can predict and manage Key Performance Indicators (KPIs), such as productivity, safety, cost, equipment failures, fuel consumption, and tire wear under different road and load conditions. By breaking-down the various systems of an autonomous haulage truck and simulating the overall haulage system using a Monte Carlo approach, the model becomes a flexible and powerful tool to use within a mining organization. Direct comparison to a manuallyrun system can be done to show the cost and operational benefits of automation. Project managers can use this tool to guide decision-making about possible application of autonomous haulage trucks at a specific mine site.

May 1, 2010

By Robert M. Owen

The reconstruction of ocean history has been a major focus of marine research over the past decade. A significant outcome of these investigations is the recognition that certain types of marine mineral deposits are linked to regional to global scale changes in ocean composition and climate conditions. Manganese-bearing deposits are of particular interest in this regard because changes in their occurrence, distribution and/or composition are responsive to both biochemical and geological factors. Analyses of such deposits whose formation spans critical age/epoch boundaries thus provide clues concerning the interplay of different process during anomalous periods in Earth history. Recent studies demonstrating this deposit - event - process relationship include: (1) Changes in the bulk chemical composition of ferromanganese crusts during the Late Miocene-Early-Pliocene (-7-3 Ma) that coincide with a period of enhanced biological productivity in the eastern equatorial Pacific upwelling zone; (2) The formation of large statiform manganese deposits at the Cenornanian- Turonian Boundary (-92 Ma) in association with widespread oceanic anoxia; and (3) Increased deposition of hydrothermal precipitates caused by tectonic reorganizations at the Paleocene - Eocene boundary (-55 Ma) that resulted in global-scale changes in atmospheric and oceanic circulation and climate.

Jan 1, 1995

By Roger Keller, Jason Ryan

A number of studies have evaluated excavation methods for the construction of subsurface facilities for a potential deep geologic repository for the disposal of nuclear waste at Yucca Mountain, NV. Many of these studies suggest that where TBM (tunnel boring machine) methods are not applicable and alternative mechanical excavation methods can not efficiently excavate harder rock drill and blast methods may be the most efficient means of excavation. However, a number of concerns regarding drill and blast applications have been raised in these evaluations, most notably the affects of blasting on the surrounding perimeter, as isolation of the waste by the natural barrier of the surrounding rock is a key element in the concept of a deep geologic repository.

Jan 1, 2001