Search Documents

This paper states how alloy and welding advances have made possible the rapid development of the use of aluminum in the construction of equipment for earth moving and off -highway rock hauling. The main details are given regarding the construction and field testing carried out on an aluminum prototype body. The test results of strain gauge readings are analysed, and a description is given of how these have been applied in subsequent designs. The increase in the number of aluminum units put into the various types of service in Canada, as well as the problems encountered, is described, and the experience gained from five years of field service is discussed in some detail. An assessment is also made of the durability of the e units. The economics of using aluminum, together with the current development position, are reviewed, and predictions are made for considerable future increases in the use of aluminum units in open-pit and off-highway operations.

Jan 1, 1964

By Eckersley J, Boyd G

A brief review is presented of the mechanisms and causes of spoil pile failures which have occurred at the Goonyella Mine. In particular, the results of a recent geo- technical investigation of the spoil dumps in the Cleanskin pit are briefly presented. Spoil pile hydrology is discussed in relation to the use of effective stress concepts in the analysis of spoil pile stability. Experience in relation to stabilisation of dragline dumps is discussed as well as the likelihood of current techniques being success- ful in the prevention of gross failures if prestrip material is placed in existing spoil piles. Parameters exerting a major control on dump stability are outlined.

Jan 1, 1981

By M. J. Sapko

The Bureau of Mines conducted laboratory-scale flammability experiments to investigate the possible use of water spray systems for inerting or quenching mine-gas ignitions, such as those encountered at the working face of a coal mine. The inerting results for premixed methane-air-water mixtures indicated that water droplets of less than 10 µm tend to be as effective as the vapor. Water requirements for inerting such mixtures were much smaller than those for quenching the sustained flame propagation by the application of water sprays. The minimum water mass concentration for quenching methane-air flames increased linearly with increasing droplet diameter (surface weighted mean) and decreased with increasing spray temperature, whereas the droplet surface area required per unit volume was essentially constant for a given gas mixture composition. Data extrapolations indicated that a quenching system may be feasible for the longwall mining application.

Jan 1, 1977

By A. D. Stewart

El presente texto señala la geología como materia de enseñanza en las universidades británicas. En este sentido, si la geología se comprendía como una materia integral que trata del estudio de la tierra, aquí se ofrece una serie de cursos independientes. y especializados. Dicha variación es consecuencia del aumento de publicación de nuevos conocimientos. Como una alternativa a la organización existente en geología, se propone un sistema jerárquico de tres niveles, donde la escala juega un papel clave y la enseñanza, es un proceso orientador antes que descriptivo. La principal ventaja de este esquema sobre el tradicional es que la relación entre segmentos de materia en cualquier nivel es conducido por profesores en el siguiente nivel superior, sin que haya necesidad de colaboración detallada entre profesores dentro o entre niveles.

Jul 1, 1969

By Sara Moshfeghi, Seyyed Majdeddin Mir Mohammad Hosseini, Abolfazl Eslami

"Due to variety of current pile bearing capacity methods based on the cone penetration test (CPT), for optimum design, it is necessary to evaluate the performance of such methods in different geotechnical conditions. Geotechnical databases including piling and in-situ testing records have been recognized as useful tools for analysis, design and economical construction. In order to evaluate pile bearing capacity methods, AUT-CPT&Pile database has been compiled including 450 full scale pile load tests and CPT sounding records. This database consists of different pile types with a relatively wide range of geometries and various soil conditions. Forty three records of piles driven in sand deposits were then employed to evaluate effects of ultimate capacity interpretation criteria from load displacement diagrams. The Davisson offset limit criterion, the Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter were compared to estimated capacities from ten CPT based design methods currently used in practice. The Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter lead to reasonable results, the Brinch Hansen 80% criterion showed less scatter. For evaluating the accuracy and the precision of CPT-based methods, the results were compared to estimated capacities. Results of comparison indicate that the CPT-based methods mainly predict the pile capacity withreasonable accuracy.INTRODUCTIONAmong the different approaches of estimating the pile bearing capacity, in-situ tests, especially, the cone penetration test (CPT) are favored due to the cone similarities with piles in modes of installation as well as fast and continuous profiling. This trend is practically well established where deep foundations are to be constructed in soft to medium subsoil deposits (Eslami and Fellenius, 1997; Mayne and Niazi, 2009).Employing different design methods results in a wide range of values which complicates the selection of an appropriate one to determine the pile bearing capacity. Several studies by Briuad and Tucker (1988), Eslami and Fellenius (1997), Abu Farsakh and Titi (2004), Schneider et al. (2008) and Eslami et al. (2011) confirm disparity of different design methods predictions. Thus, for optimum design, it is necessary to evaluate and compare the performance of current methods.Geotechnical databases are known as helpful tools in research and practical applications for optimizing analysis and design and are mainly used for management and interpretation of data, evaluation of design methods, calibrating LRFD or ASD design factors, etc. Pile lateral and axial load tests are examples of databases in geotechnical engineering. A summary of several CPT and pile load test databases is presented in Table 1."

Jan 1, 2017

By Gutsche O, Kapur PC

Experimental data on the production of fines as a function of specific grinding energy consumption show that in general the energy utilisation in a choke fed high-pressure roll mill is higher than in a ball mill, but lower than in the single-particle mode of comminution under slow compressive loading. There is some evidence to suggest that the presence of water in feeds improves the energy efficiency of pressurised roll milling somewhat. Within a wide range of energy input, the size distributions of the ground product are self-similar, the logarithmic median size decreases linearly with the amount of fines produced and the inverse of the median size increases linearly with the energy spent. The production of fines as a function of energy expended follows essentially the same pattern as the one frequently encountered in media mills. The kinetics of grinding in the high-pressure roll mill can be simulated satisfactorily by modifying the standard particle population balance equation in order to account for energy dissipation in the tightly compressed bed. Common characteristics and important differences in grinding by the media mill and the high-pressure roll mill are highlighted.

Jan 1, 1993

By L. Wilfley, G. A. Calboreanu

"Wear resistant 25% Cr hard cast iron is a heterogeneous material containing 1,600 HV hard chromium carbides embedded into martensitic matrix. It is the most used cast alloy in wear operations of mining industry, chemical industry, fracking, etc. During the last decade the hard iron manufacturers increased wear resistance in the following ways: • Reduce / eliminate harmful retained austenite and chromium + carbon depleted areas especially within eutectic carbide cells. In Max5A the improved 25% Cr alloy brittle carbide eutectic cells are removed which increases toughness. • Delay delamination between chromium carbides and matrix particularly during sliding abrasion wear. Delamination commences at the weakest chromium carbide – matrix contact lines exposing chromium carbide to localized bending stresses which gradually chip carbides away. Once the chromium carbide base is removed accelerated wear degradation occurs. • Evenly randomize and avoid discontinuities in the chromium carbide network. When chromium carbides are perpendicularly positioned to the wear surface wear rate is minimized. On the contrary the highest wear rate takes place when 3D oriented chromium carbides are parallel with the wear surface. In this case chromium carbides cover top network discontinuities being just matrix supported which leads to rapid carbide cracking. The new hard iron discussed in this paper fulfils and exceeds the above requirements increasing the casting service life around 250% in various wear operations. Physical and mechanical properties of Max5A are compared with well manufactured Industry Standard 25% Cr hard iron. The paper presents practical accomplishments obtained in the USA, South America and India. INTRODUCTION The chemical composition of Max5A and Industry Standard 25% Cr are identical like specified by ASTM A532 Class III Type A requesting C = 2.0-3.3% and Cr = 23.0-30.0%. Manganese, silicon, nickel, molybdenum and copper contents are limited by maximum accepted quantities.[1] According to published data the eutectic chromium carbides chemical composition of 25% Cr hard iron is Cr = 54% and C = 8% which indicates strong depletion of chromium and carbon along chromium carbide - matrix interfaces. [2] The optimized Max5A microstructure has minimized retained austenite, is devoid of harmful carbide eutectic cells and has the most advantageous chromium carbide and secondary chromium carbide morphology. This favorable microstructure increases wear resistance, mechanical properties and corrosion resistance. The paper compares the Max5A microscopic features and mechanical – physical properties with similar properties of high quality Industry Standard 25% Cr."

Jan 1, 2017

Mining companies in Australia have grown in size and complexity over the past 20 years. The same period has seen exten- sive changes in the operating environment, with greater competition and intensified in- dustrial and social pressures placing new demands 'on mining activity. The new condi- tions require a management approach that emphasises strategic planning rather than operational efficiency. Strategic management evolves through four distinct phases, namely, financial planning, forecast-based planning, externally oriented planning and 'true' stra- tegic management. The most difficult transi- tion to make is from Phase 2 (forecast-based planning) to Phase 3 (externally oriented plan- ning) since management is often too involved in operations to find time to develop and main- tain a strategic orientation towards the mar- ket and competitors. Reorganisation of re- sponsibility for operations and improved op- erational processes enable management to concentrate on external opportunities.

Jan 1, 1980

By Jay N. Fairbanks, Richard G. Robinson

This paper discusses a computer program and related formulas for fire fighting responses by coal mine personnel. The computer will interpret the mine air analysis, print reports, and provide relevant graphs allowing quick and accurate responses to coal mine fires.

Jan 1, 1983

By R. Bhaskar

The advantages of recirculation of air in underground mines have been well recognized, and several papers have been written on the subject. Issues of concern to the various segments of the mining industry relate to the health and safety of workers, specifically, methane and respirable dust build-up in the air, high humidity and temperature at the work face. This paper presents a survey of various studies pertaining to recirculation as a prelude to the experimental and quantitative studies performed by the authors. Experiments were performed at a trona mine on the transportation and deposition of dust along the return airways, for three different velocities. Modeling studies were performed using dust deposition models. The model predicted data were compared with experimental data in order to lay the foundation for the development of advanced predictor models for recirculation in trona mines. Two models for dust deposition were analyzed. The model predicted data are in divergence from the experimental data, indicating the need to develop better models.

Jan 1, 1992

By H. H. Hausner, H. S. Kalish

IN recent years zirconium and beryllium have become of great interest because of their special properties. Zirconium is known for its remarkable ability to absorb the gases oxygen, nitrogen and hydrogen, has extensive use as a getter in electron tubes and has indeed become the primary metal in the manufacture of photoflash bulbs. Beryllium is of interest because it is light metal and as such could supplement aluminum and magnesium in light metal applications. The late development of zirconium ductile at room temperature produced by both the iodide and calcium reduction methods has stimulated frequent articles on this metal in the recent literature. Beryllium is so closely akin to zirconium crystall-ographically that some investigators are of the opinion that beryllium should be ductile at room temperature if it were pure enough. The crystallographic relationship of beryllium and zirconium, the interest created in Be-Zr alloys where the zirconium is believed to function as a remover of solid solution gas in beryllium and thus increase the ductility of the beryllium rich alloy, and the amenability of these metals to powder metallurgy methods stimulated this approach to an investigation of the system Be-Zr. Preliminary work showed that a zirconium compact melted when pressed in contact with a beryllium compact and sintered at 1250°C, without any apparent final bond between the two. A search of the literature revealed nothing pertinent about the Zr-Be system or about any zirconium - beryllium alloys. In 1936 Misch³ vaguely identified the compound ZrBe2 and reported that it has a deformed cubic structure. Two patents," , were issued to Mach-lett Laboratories in 1943 and in 1946 regarding the addition of small amounts of zirconium to beryllium in order to improve the ductility of beryllium so that it may better be used for X ray windows. In considering the alloy formation of beryllium with other metals Raynor thought it unlikely that zirconium would have any solid solubility in beryllium. From this indefinite information nothing could be ascertained about the possible use of Zr-Be alloys or the use of these metals intimately. A brief preliminary study of the system Zr-Be by powder metallurgy methods was undertaken to provide regions for more intense studies of Zr-Be alloys and as a guide to a formal phase diagram determination. The investigation described in the following pages was completed in less than three weeks. The usefulness of this rapid method to facilitate phase diagram studies and new alloy investigations will be shown. Materials and Procedure Zirconium powder was produced from crystal bar stock of high purity supplied by Foote Mineral Co. The crystal bar was converted to hydride at 730°C, crushed, and the hydride decomposed in purified argon at 850°C. 60 pct of the powder passed through a 325 mesh screen, 40 pct of the powder was —140 mesh, +325 mesh and the average particle size of the total was 8 to 12 microns. The beryllium powder was used as re-

Jan 1, 1951

By S. L. Crouch

This paper describes a numerical procedure for the computation of the displacements and stresses induced by the mining of a tabular ore deposit in faulted ground. The numerical procedure is based on the displacement discontinuity method, which can be regarded as an application of Salamon's 'face element principle' to cases in which the reef plane is faulted into several sections, or even folded in an arbitrary way. An element of a fault is modelled in the same manner as an element of the reef, except that a fault element is allowed to undergo permanent inelastic deformation (i.e., slip) if the stresses transmitted through the fault-filling material satisfy a Mohr-Coulomb yield condition. An iterative technique for the incorporation of a Mohr-Coulomb yield condition in the general displacement discontinuity method is explained. This technique is illustrated by means of a simple example involving the mining of a flat-lying reef intersected by a fault. The displacements and stresses at selected locations along the fault are examined as the reef is mined, element by element. A consideration of the energy changes reveals that the occurrence of slip along a fault leads to a sudden increase in the energy release rate due to mining as the excavation intersects the fault. The energy release rate then falls off abruptly to a value less than that which would occur in the absence of any slip, and gradually builds up to re-establish the conditions that would exist in unfaulted ground.

Jan 1, 1979

By C. R. Fast, George C. Howard

Laboratory and field testing of various squeeze cementing techniques and materials revealed that many improvements could be made in squeeze cementing operations. The use of a slow-pumping squeeze cementing procedure permitted the control of the quantity of cement displaced into a formation and aided in obtaining a high final squeeze pressure. Field testing indicated the desirability of obtaining high final squeeze pressures, the need for improved formation breakdown fluids, and the necessity of controlling the pressure differential during testing after a squeeze job. INTRODUCTION During the past few years, squeeze cementing operations have been investigated, both from the theoretical as well as the practical point of view, in an effort to arrive at some solution to the many and varied problems that arise with this type of operation. A review of well files indicated that in many instances, wells were being squeeze cemented four and five times before a satisfactory pressure buildup was obtained. There seemed to be considerable variation in opinion as to the proper method of squeeze cementing, as well as disagreement as to the proper breakdown agent, the quantity of cement that should be used, type retainer and length of WOC* time that was necessary. Consequently, it was deemed advisable to approach this problem theoretically, field testing each idea developed in hopes of eventually arriving at a squeeze cementing procedure that would give reasonable assurance of a successful job after one squeeze cementing operation. This investigation was. therefore, divided into two broad headings: (1) Preliminary studies, which include both theoretical and laboratory studies, and (2) Field investigations to determine the proper squeeze cementing methods. PRELIMINARY STUDIES Overburden Pressure Studies Squeeze cementing problems are so intimately related to the earth's overburden pressure that solutions to them are very difficult, if not impossible, without an understanding of the nature and magnitude of the overburden pressures encountered at the depths of producing wells. It was thus felt that the first approach to research on squeeze cementing should be made through a study of these pressures. Since there has been rather loose usage of a number of the terms related to overburden preasure by different writers, the terms to be subsequently used are defined here. Theoretical overburden pressure is the calculated pressure at any given depth exerted by the theoretical weight of overlying formations as calculated from the average rock density. Fluid displacement pressure is that pressure at which fluid can be injected into a formation after it has been broken down. It may be more or less than the theoretical overburden pressure. Formation breakdown pressure is that pressure at which a formation parts or breaks and is usually thought of as fluid displacement pressure plus rock strength. Breakdown agent is that fluid with which the formation is fractured. The first step in the study of the earth's overburden pressures involved a review of pertinent technical literature. The general opinion expressed was that the overburden pressure gradient of the earth's formations is roughly 1.0 psi per foot of depth, and that application of sufficient pressure to stratified formations. will cause them to part at or parallel to the bedding planes. The second step in the study of overburden pressures involved a study of available well data in an effort to obtain some definite information as to the actual values experienced in the field for the above mentioned terms. Data from 115 cement squeeze jobs in the Gulf Coast area and 46 cement squeeze jobs and acid jobs in the West Texas-New Mexico area were closely analyzed. The analysis of these data showed that the average formation breakdown

Jan 1, 1950

By Yi Luo

In the study of the topographical effects on surface movement due to underground longwall mining, the factors that affect the incremental horizontal displacements are identified using 10 collected cases. Based on this study, the angle of surface natural slope is the major contributor to the incremental horizontal displacement while the total movement is also playing an important role in some cases.

Jan 1, 1996

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2006

By Jesse L. . Jr. You

Tunnels in the granitic Climax stock at the Nevada Test Site were inspected for keyblock occurrence. Thirteen relatively large pyramidal keyblocks were located in about 230 m (750 it) of tunnel. Orientations, dimensions, joint roughness coefficients, and joint compressive strengths were measured for the faces of nine keyblocks. The measurements were used to back-analyze keyblock stability to check the validity of a numerical model for keyblock behavior. A newly developed three-dimensional numerical model correctly predicted whether or not each keyblock failed in six of eight cases. The two exceptions involved stress conditions and keyblock locations that clearly violated the assumptions that underlie the stability model. The observations also allowed the effect of tunnel orientation on keyblock occurrence to be evaluated. Of the thirteen observed keyblocks, nine large blocks were found in less than 30 m (100 ft) of the Piledriver drift (which runs N56E) while only four blocks of comparable size were observed in 200 m (656 ft) of the Spent Fuel Test--Climax drifts (N61W). The orientations of the keyblock faces were checked against known discontinuity set orientations; some of the faces correlated well with mean set orientations, whi.le other faces were fringe members of sets. Stereographic techniques were used to examine the frequency of keyblock occurrence and to determine the maximum keyblock size that could be encountered with a given combination of discontinuities. Keyblock occurrence was found to be affected by tunnel orientation in a predictable way; this can be used to guide or improve tunnel design practices.

Jan 1, 1986

By John W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct ironmaking pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicates that 69% are less than 2.5 um across, 21 % are 2.5-5 um, and 10% are larger than 5 um. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By Y. Zhoa

The surface morphology of materials is of fundamental importance to many surface related applications, such as wetting, friction, reflection, drag, and adhesion. Various approaches for micro/nano patterning atop polymer surfaces have been proposed in recent years. However, a cost effective technique is still highly in demand. In this paper, we demonstrate a novel but rather simple and generic approach for surface micro/nano patterning using shape memory polymers (SMPs). Different types of novel patterns are realized and their 3-D surface features are quantitatively analyzed by a PLµ Confocal imaging profiler.

Jan 1, 2010

By Mark Springett

The problems inherent in sampling low- grade deposits have long been recognized. As economic grades become lower with increasing metals prices and improvements in recovery technology then the previously difficult sampling problem has consequently become even more demanding. The breakdown of the sample process and error is illustrated by describing in the remainder of the paper some sampling practices that have been utilized on mining and exploration properties and by describing some problems that have been encountered, providing a series of cautionary tales to those involved in any aspect of mine or exploration sampling.

Jan 1, 1983

By R. V. Higgins, A. J. Leighton

A fast method is needed for calculating thoroughly the performance of two-phase flobr~ in reservoir rock with complex geotrietry. The authors present such a method and .slzow its accuracy by romparison with laboratory performrrnce of a five-spot pattern. In making the performance c.alculations, the octant of the five-spot pattern was divided into four channels. The computer tinle required for the culculation was one rllinrcte. This is rorighly about minute per channel. INTRODUCTION By using an electronic computer it is now possible to make reservoir performance calculations in which fewer assumptions and more significant variables are included than was possible with a desk calculator. These performance calculations include such variables as the properties of the reservoir rock and its contained fluids, properties of the rock-fluid system and even different well-spacing patterns. Usually, the more variables that are included the higher the computer cost—and time on the computer is expensive. As a result, a short procedure is needed so the many variables will be included and accurate performance calculations will result. If a reservoir is composed of alternate layers of permeable and impervioi~s rock, and if each conducting layer has a different relative permeability, the combined computer cost for calculating each layer by the present long computer programs (which includes different well-spacing patterns and other variables) would be expensive. The performances of complex spacing patterns in a field often are studied by a potentiometric model, but in these model studies the analogy is to the flow of only a single phase. This paper presents a procedure to calculate the performance of a five-spot pattern with two phases flowing using a potentiometric model as a guide for the dimensions of channels and other related data. The time required to calculate the complete performance is about one minute on the IBM 7090 or four minutes on the IBM 704. The procedure can be extended to calculate the performance of more complex well spacings or an entire field with little modification. The procedure has been tested on the performance of the laboratory water floods of a five-spot pattern reported by Douglas, et alThe range of viscosity ratios in the laboratory experiments is from 0.083 to 754, which is extensive. The accuracy of the performance calculations is excellent as shown by the plotted points in Fig. I. The recovery as influenced by the geometry of the five-spot, taking into account the deviation from true radial character, has been predicted by Aronofsky and Ramey." The authors used a potentiometric model to determine the sweep efficiency to breakthrough of the flooding agent. Dyes, Caudle and Erickson,' by means of a laboratory model, show the influence of mobility ratio on recovery after breakthrough of the injected material. Dyes, et ai, used the X-ray shadowgraph technique and miscible phases in their studies. Craig, Geffen and Morse from the analysis of the performance of their laboratory model correlate many variables, including average saturation of a flooding agent determined by permeability relationship. Craig, et al, used X-ray shadowgraphs to determine the sweep efficiencies in sandstone models. In this report the sweep efficiency is not needed, and the important effect of continuously changing saturation gradients before and after breakthrough