Search Documents

By Peter Shuttleworth, Chris Fesq, Eddie Woods

Precast concrete segmental linings for tunnels have traditionally been designed with conventional steel bar reinforcement. In many cases, this has been satisfactory in service, but in others, major problems have occurred with the durability of the linings. Commonly this has resulted from corrosion of the reinforcement, mainly from chloridesin ground water, causing spalling of the concrete and leading to very expensive and disruptive repair programs. This paper discusses the relative merits of designing tunnel linings with steel fiber reinforcement to provide long-term durability, improved impact resistance and toughness for greater load capacity across joints, enhanced robustness during transportation and erection, plus improved fire resistance with the addition of polypropylene fibers. Guidance is also given in the selection of the correct fiber type, mix design and testing methods to establish the optimum dosage required and production techniques to ensure even distribution and compaction.

Jan 1, 2005

By William H. Schiffbauer, William D. Mayercheck, August J. Kwitowski

This report summarizes work sponsored by the Bureau of Mines in the development of a remote operating system (ROS) for controllng a thin-seam continuous miner (TSCM) 500 feet or more distant from the extraction face. Detail s are provided on ROS subsystems including the continuous miner, video equipment, controls and displays, the electronic control system, and the operator station.

By R. J. Wensley

The use of small substations for the supplying of 275-volt energy to the locomotive and cutting machines in coal mines is a well-established practice. A few years ago, when labor costs were lower, these substations were located as near to the load as possible, and an operator was provided for each station. This practice has now become so expensive that substations are being located with reference to other mining machinery, such as hoists or pumps, so that one operator can look after both. Sometimes the substation is operated by one whose duties make him traverse quite a large area. In such cases the interruption of alternating-current supply may produce a long interruption in the direct current, as the station cannot resume service until this man reaches it. Such interruptions interfere seriously with production and may easily counterbalance the supposed saving gained by such operating methods. The grouping of substations for convenience in operating may also result in excessive copper loss and consequently poor trolley voltage, with its attendant evils of low locomotive speeds and increased locomotive motor maintenance. The speed of the coal-cutting machines will also be reduced. By relieving the substation of its burden of the operating labor cost, the most economical location, from an electrical standpoint, may be chosen. The matter of machine insurance should also be considered. If an attendant is caring for several kinds of equipment, he cannot watch the machine continually for signs of trouble; therefore, continued overload, phase failure, low alternating-current voltage, bearing trouble, etc. may result. Some partly automatic equipments have been installed; these have protection against low voltage, reverse current, and bearing trouble and are provided with automatic reclosing circuit breakers. This is a step in the right direction but it does not go far enough to give first-class machine insurance. The saving in maintenance costs is often the smallest item, when considering the automatic substation as machine insurance. When the coils in a machine are roasted out, due to continued overload or to opera-

Jan 1, 1922

By J. R. Walls

Mining is one of world's oldest industries. Its rich history continues into modern times. The Waste Isolation Pilot Plant (WIPP) located in southeastern New Mexico is writing the next chapter in mining history. In fact, WIPP technology is the key to closure of the nuclear cycle with the disposal of nuclear waste in a deep geological repository. It might seem odd that the age-old institution of mining would be linked to the problem of nuclear waste disposal. In fact, the nuclear industry would not exist without mining. Uranium ore is mined from either underground or surface mines as the initial step in harnessing the magnificent resource of nuclear energy.

Jan 1, 1996

By Leslie S. Rubin, John C. Roberge, Mackenzie Burnett

A self regulating helical inducer has been developed and tested for dry injection of coarse or fine solids into a hydraulic pipeline. This centrifugal pumping device has also been modified and tested for use as a boost pump in medium and long distance pipeline haulage systems. The helical inducer has been operated as an integral component of a slurry injection vehicle. This compact, low profile vehicle also includes crushing and screening components, solids feeding components, a track drive system for mobility and is run by a single operator. The helical injector and boost pump operate without speed and flow controls allowing for the practical hydraulic transport of excavated materials.

Jan 1, 1983

There is considerable variability in the level of detail incorporated in prefeasibility studies relating to mining developments. Hence, when undertaking a review or audit, it is critical to attempt to ascertain at an early juncture precisely who has compiled the various facets of the study, for what purpose it was intended and the terms of reference given to the authors. Likewise, when commissioned to undertake an audit it is preferable to have proper terms of reference and to be aware of the purpose to which the audit will be put.These factors will influence the degree of detail an auditor would expect to find in the study and consequently, the degree of effort/time required for the audit process. In most instances audits do not imply recalculation of the entire study or modifying it in anyway, but involve an overall assessment of the methodology used, combined with spot checking of detail. One of the most difficult aspects is to determine a realistic order of accuracy for the overall study when the accuracy of the individual components may differ markedly.

Jan 1, 1990

By N. Ragoonanthun

Paper written on project work carried out in partial fulfilment of B.Sc. (Mining Engineering) degree This report investigates the optimization of a raiseline in order to open up the ore reserve quicker. The project was carried out at Mponeng Mine (an Anglogold shaft formerly known as Western Deep Levels 1 Shaft and South Mine, in Carletonville). The project was divided into two focus areas namely: ?To design an optimum layout of a raiseline, which includes the scheduling of all activities for the establishment of the infrastructure. Consideration was given to the blasting practice, mining cycle, orepass placement and slusher positioning. Two designs were carried out on the above basis. ?The design of a ledging operation/practice to match the optimized layout of the raiseline. The ledging cycle design involved a thorough investigation into the possible use of drill rigs, Electronic Delay Detonators (EDD) blasting technology, longer drilled holes, Threshold Blasting (THROB),and water jet cleaning.

Jan 1, 2003

By F. E. Brantley

Blister copper was successfully deoxidized with any of a variety of reducing gases; lancing techniques or a vertical-column furnace were used to contact the copper and gases. Of the gases tested, butane, when used to lance molten copper at about 1,200° C, reaction temperature, was slightly more effective than propane, natural gas, carbon monoxide, or reformed gas for deoxidizing copper from about 1.0 to less than 0.1 percent oxygen content, Laboratory-scale tests revealed that the vertical furnace, composed of a heated column packed with silicon carbide chips or hollow carbon cylinders, was significantly faster and more efficient than the lancing technique for deoxidizing molten copper with any of the gases tested. Comparison of the gaseous-reduction method with the conventional poling method suggests that the gaseous method has important technical and economic advantages for deoxidizing blister copper to any readily controlled amount of residual oxygen content.

Jan 1, 1962

By V. B. Teffo

The aim of the project was to experimentally determine the coefficient of restitution, and static and rolling friction of Eskom-grade coal for discrete element modelling (DEM). These parameters will be used in further DEM studies to simulate the flow and behaviour of coal during conveyance. For the simulation to yield realistic results, the parameters for the different coal shapes identified in the samples were determined. DEM uses spherical particles, and it was found that the difference between the DEM default parameters and those measured is significantly different, by as much as 97%, which illustrates the importance of experimentally determining these parameters. The spherical particles in DEM can be used to construct the various coal shapes identified, and the parameters measured can be used to simulate realistic results. The conveyance system can then be optimized accordingly.

Jan 1, 2013

By W. Bullen

A hypothetical economic model has been developed for diamond projects in the Canadian Arctic using data from recent exploration and mining projects. The model reflects economic conditions applicable to the diamond mining industry in the Canadian Arctic at the present time. The economic model captures pre-production expenditures, production data, and post-production costs. Before- and after-tax cash flows are derived from the data along with the relevant economic criteria. From the corporate perspective, the model provides guidance concerning the minimum size and/or in situ value per tonne requirements of targets being sought in order to ensure economic success and predict exploration and development expenditures. From the government perspective, the model provides an indication of income and mining tax revenues that can be expected from a particular diamond project. The model shows, on average, diamond projects in the Canadian Arctic are expensive to explore for and develop, but are economically robust under the present conditions. They generate great economic return for mining companies and significant amounts of tax revenue for governments. The fact that diamonds can be transported directly from the minesite by air makes them particularly attractive targets for mining companies that operate in the Canadian Arctic.

Jan 1, 2006

By Helvio P. G. Santafé Jr., Ruben J. S. Rodriguez, Sergio N. Monteiro, Teresa E. Castillo

"The coir fiber extracted from the husk of the coconut fruits are worldwide available in tropical regions as a low cost lignocellulosic by-product for many applications including composite filler in automobile parts. Possible uses above room temperature require information on the thermal behavior of these coir fiber composites. Therefore, the objective of this work was to perform thermogravimetric, TGA and DTG, analysis on polyester matrix composites incorporated with different volume fractions of coir fiber. In general, it was found that thermal degradation associated with weight loss occurred in three stages. Changes were also observed in the DTG peaks that could be attributed to the coir fiber participation through the decomposition of its lignocellulosic structure.IntroductionThe development of new materials has always been motivated by the need of improved properties. This was the case of modem composites with combination of properties that surpass those of conventional monolithic metallic alloys, ceramic or polymers, from which composites are made. A typical example is the synthetic fiber reinforced composite with specific strength i. e, ultimate stress divided by density, higher than any other monolithic material. Today, however, our global society is concerned with serious environmental problems and thus demanding that new materials be developed with distinct characteristics. They are known as environmentally correct and are expected to be sustainable, which corresponds to the condition of being biodegradable, renewable, recyclable and neutral with respect to C02 emission, considered the main responsible for global warning [1]. Synthetic fiber composites cannot meet these requirements. Consequently, new composite reinforced with cellulose-based natural fiber are being developed [2-8] and are already replacing the synthetic ones in several engineering fields including the automobile industry [9-11]. These composites have additional advantages owing to the lignocellulosic fiber benefits of being diversified, abundant, less expensive, lighter and of societal interest [8]. In some cases even technical advantages such as non-abrasive effect to processing equipments and more flexibility exist in comparison to synthetic fibers."

Jan 1, 2011

By Paul C. Rusanowski

Mining is a waste intensive industry, oftentimes producing hundreds of kilograms of waste rock and tailings for every gram of metal recovered. Disposal of mine tailings is a major concern in most mining operations. In Southeast Alaska the steep terrain and high seismic hazard province limits cost effective opportunities for land disposal of tailings. The lack of infrastructure and long travel distances generally limits secondary utilization of tailings, as well. Since the mines are located close to tidewater, submarine tailings disposal is an attractive option for tailings management. At the present time the EPA will not issue a permit that authorized marine tailings disposal from any mining process that includes flotation technology. Upland disposal is the "Best available technology" and must be used. Consideration of submarine disposal is generally precluded because the tailings are contaminated with fluids from the flotation process. However, when developing technological solutions to minimize environmental disturbance, destruction, pollution, and risk, submarine tailings disposal deserves another evaluation. In Southeast Alaska it may be the "Best available technology" based on an assessment of all issues and concerns in these mining projects.

Jan 1, 1991

ENROLLMENT of both undergraduate and graduate mineral engineering students rose approximately 11.8 pct over last year to a total of 12,830. Leading again in the enrollment climb was ceramic engineering which increased by about 21 pct. Approximated increases in enrollment of the other mineral engineering categories, in order, were: metallurgical 17.7 pct; petroleum 13.3 pct; geological and geophysical 3.3 pct: and mining proper, the lowest with 2.9 pct. Total ECPD school enrollment climbed to 242,405 -just below the 1947 peak, but 14.4 pct higher than 1955. Engineering enrollments have shown a general increase since 1951, and freshmen enrollments have climbed steadily since 1950.

Jan 5, 1957

By Narasimha Mangadoddy, Teja Reddy Vakamalla

"Vertical hydrocyclones are very common in most of the comminution circuits. Inclined cyclones are also found for specific mineral processing applications. In this work, Computational Fluid Dynamics (CFD) technique and experiments are used to find the reasons behind the inclinations effect on hydrocyclone performance characteristics. The water and silica slurry experiments are conducted with 75 mm hydrocyclone at different inclined positions (0-600) to the vertical plane. Corresponding two-phase numerical simulations are performed with Volume of Fluid (VOF) model coupled with Large Eddy Simulation (LES) turbulence model. Multiphase simulations are carried out with Algebraic Slip Mixture model modified with lift, drag forces and Newtonian rheology model corrected with fines for various feed solids concentration. A raise in the under flow solids percentage, cut diameter and a reduction in the water split is observed with the inclination. Electrical Resistance Tomography (ERT) and High Speed Video (HSV) data is used to cross validate the inclined cyclone’s CFD air-core and solids concentration data. Predicted efficiency curves are found in a close agreement with experiments for all the inclinations. Comparison of experimental and predicted flow data clearly follows trend with the literature. Key words: Hydrocyclone, CFD, ERT, inclination, water splitINTRODUCTIONHydrocyclones are devices used to separate or classify particles based on particle size difference in the water medium. Their usage is very wide in chemical, petroleum, mineral and bio industries due to its structural simplicity, high throughput, small volume, low cost and maintenance. Cyclone mainly consists of a cylindrical section followed by a conical section attached to a single feed inlet and two product outlets named vortex finder and spigot. It works on the principle of centrifugal sedimentation. The slurry is fed tangentially to the hydrocyclone, in which larger particles are moved towards the wall and separated by centrifugal forces to the underflow. Smaller size particles follow liquid due to drag forces to the overflow. With its simple structure, the flow behavior inside the hydrocyclone is quite complex. Vertical cyclones are common in practice in most of the comminution circuits. Horizontal cyclones can be found in extreme cases which are for installation convenience rather than for process reasons. Inclined cyclones are also present for specific mineral processing applications. In coal preparation plants, dense medium cyclones are operated near to horizontal inclination of 20 degrees to allow large spigot sizes for sinks removal, self-drain of contents during shutdown. In the phosphate removal, dense medium cyclones are inclined with an angle between 0-90 degrees for better separation of ore and tailings (Liu Feng et al., 2006). Even in the clusters, hydrocyclones are mounted with an inclination around the feed distributor for uniform distribution of slurry and under flow collection. It is believed in mineral processing industry that inclined cyclones would fetch the benefit in number of ways while classifying the material by size. Gravity influences the cyclone performance through the air core size and position variations in large cyclones. It also favours the cyclone operation at coarser cut points without varying any other design and operating parameters. Minimizing fines misplacement to underflow can be achieved with inclination."

Jan 1, 2016

By G. G. Morgis, J. J. Forbes

"INTRODUCTION The greatly diversified and increased uses of beryllium and its con& pounds in recent years have focused attention on the health hazards incident thereto. The Bureau of Mines has a fundamental interest in safety and the elimination or reduction of health hazards in the mineral and allied industries, and it recognizes that serious hazards are inherent in the production and use of beryllium and its compounds. This circular presents a review of the literature pertaining to such health hazards but does not describe original research by Bureau personnel. Most of the bibliography has boon either quoted in part or abstracted in an effort to present information in a comprehensive and readable form.In reviewing the literature, differences of opinions wore recognized in the writings of the respective authors, but no attempt was made to evaluate such differences. This presentation was devoted strictly to reporting without editorial comment.SUMMARYAlthough beryllium was known to industry for about 150 years, its toxicity did not present any serious problems in the United States until the advent of World War II, when the increased use of this element and its compounds brought to light several toxicologic reactions occurring primarily in the lungs and skin of workers handling it. The pulmonary effects, characterized as acute pnoumonitis and chronic pulmonary granulomatosis in beryllium workers, are far more serious than the dermatological manifestations.The addition of beryllium to the list of toxic industrial metals has boon so recent that there is still some confusion in the clinical picture. Data on magnitudes of exposure likely to be responsible for the production of disease are not yet adequate. There appears to be no relation between the severity of exposure and the development of cases some of those having had severe exposure have not developed a reaction, whereas those having a slight exposure in some instances have developed a response."

Jul 1, 1950

By H. B. Merlin

"The past demands for energy and the contributions by the major sources are shown for the world and regions, and for Canada. Three forecasts of future demand are presented. By the year 2000, the world will be consuming energy at a rate of 670-700 x 1015 Btu/year. Canada's rate is estimated at 20 x 1015 Btu/year. Electricity will increase its portion of energy from 7.5 per cent to 15 per cent, and more than 40 per cent of the primary energy w1ll. be required to generate 1t. World, regional and Canad1an forecasts are g1ven for total electricity generated and for electricity generated in nuclear stations. The integral world requirement for energy by the year 2000 will be over 12 x 10 18 Btu. Current recoverable fossil and hydro reserves are about 18 x 1018 Btu. The total reserves are estimated to be seven times greater.World production of electricity in nuclear stations by the year 2000 will be almost three times the electricity produced in the world today. The amount of fuel consumed in generating this electricity will depend upon the types and mix of reactors installed. The heavy water reactors, alone or in conjunction with fast breeders and liquid fuel reactors, are the most efficient users of uranium and thorium resources. The heavy water reactors are also the most efficient producers of plutonium which will be required as fuel for fast breeders."

Jan 1, 1969

By Christof Metzger

This paper discusses the process utilized by the Kiewit?Bilfiger Berger Joint Venture (Contractor) to select, design, and procure the largest mixshield tunnel boring machine (TBM) ever implemented in North America. The mixshield will excavate the 8,534 linear m × 6.7 m ID (28,000 linear ft × 22 ft ID) tunnel for the City of Portland Oregon?s, Bureau of Environmental Services (Owner) East Side CSO Tunnel Project. TBM selection was conducted under a preconstruction contract in which the Contractor, Owner, Construction Management Consultant and Designer collaborated on TBM selection prior to commencement of construction. This paper focuses on TBM design considerations, including the use of one versus two machines, machine configuration,extended-wear protection, hyperbaric interventions, boulder digestion, and erection of a steel-fiber-reinforced segmental lining

By Donald M. Liddell

From a commercial standpoint, the only beryllium mineral warranting attention is beryl, 3Be.Al2O3.6SiO2, which is of fairly widespread occurrence. The chief deposits are in Brazil, Argentina, India, Canada and Portugal. When pure this contains about 14 per cent of beryllium oxide. The mineral richest in beryllium is phenacite, (BeO)2SiO2, or beryllium orth-osilicate, which contains 45.55 per cent beryllium oxide when pure, and if anyone is ever fortunate enough to discover a large deposit of it, it will revolutionize beryllium metallurgy. Gadoljnite, zBe0.Fe0.2Yz0~.zSi0~, is also often referred to as a beryllium mineral, though the occurrences are comparatively scant and it is of more interest as a source of yttrium than it is of beryllium. There has been a good deal of talk recently regarding some occurrences of helvite in the United States. Helvite is a complex manganese-iron beryllium silicate and, apart from difficulties that would arise in its treatment because of its compo-sition, the beryllium content of the known deposits is not high. Early Metallurgy The elemcnt beryllium was first isolated by L. N. Vauquelin in 1797.~ He crushed and heated beryl, having the idea that this heating made it more readily amenable to attack by chemicals, and then mixed the mineral with three times its weight of caustic potash and fused the mixture. The melt after cooling was dissolved in hydrochloric acid: dehydrated, and again taken up with hydrochloric acid and filtered to separate the silica. The filtrate was treated with an excess of potassium carbonate and the precipitate after draining was leached with a solution of caustic potash, which dissolved the alumina. The undissolved material was, in Vauquelin's own words, "une terre nouvelle." He dissolved the precipitate with nitric acid and evaporated it to dryness, took up with hydrochloric acid and threw the iron out with potassium hydrosulphide, though he found that to make a complete separation of the iron involved a second treatment. The solution, after throwing out of the iron, had a pronounced sweet taste, and though Vauquelin always speaks of working on "terre du beril" he suggests that the new element should be known as "glucine" (glucinum) from the Greek word for sweet, because of this outstanding property. Vauquelin did considerable work on the comparison of aluminum and beryllium, working out a separation of most of the aluminum based on its precipitation as alum. His work is reviewed at some length, since ordinarily his procedure is incorrectly stated. It will also be recognized by those who have studied beryllium metallurgy that a good many technicians have followed his ideas since, including preheating the beryl before treatment. The fusion with

Jan 1, 1944

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he's hurt. Maybe he's not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

May 1, 2010

By Alesse V, Belardi G

A new class of collectors, Mercapto-Benzo-Oxazoles (MBO), exerting selective action on copper sulphides in the presence of Pb, Zn and Fe sulphides (galena, sphalerite and pyrite), has been synthesised in co-operation with Enichem's Donegani Insitute. The collectors have a mixed aliphatic-aromatic structure and contain functional groups which form chelates with copper. Some reagents of this class having hydrocarbon chains of various lengths have been laboratory tested on a complex sulphide ore containing chalcopyrite, galena and sphalerite in pyritic gangue. Comparative flotation tests have permitted selection of the best collector for chalcopyrite, namely Methyl-Mercapto- Benzoxazole (MMBO). Systematic flotation tests have been performed with this reagent, varying collector concentration, grain size of the feed, pH and flotation time. The results obtained show that the synthesised collector is much better than potassium-amylxanthate (KAX) as regards selectivity towards Pb and Zn. Moreover, it is possible to work at natural pH (6-7) and the flotation rate is higher. In fact in the rougher stage with 80 g/t of collector at natural pH, a copper grade of 7.14 per cent was obtained with a recovery of 73.87 per cent, while the grade with KAX did not exceed 2.11 per cent for a recovery of 73.54 per cent. The amount of Pb and Zn reporting in the copper concentrate was eight per cent and ten per cent respectively, while with KAX it was no lower than 24.34 per cent and 22.71 per cent in that order. After two minutes flotation a copper grade of 5.2 per cent with 52 per cent recovery could be attained, against a grade of 2.5 per cent and a recovery of 44 per cent in the case of KAX. The efficiency of this new collector has been ascertained on two samples of complex sulphide ores of diverse mineralogical composition.

Jan 1, 1993