Search Documents

By Philip W. Holland

The Bureau of Mines has developed a trace helium analyzer for deter-mining helium-4 in the parts-per-billion range. The instrument is used for analyzing pure gases, laboratory-prepared standards, and atmospher-ic samples. Accuracy at the 95-pct confidence level in the 50-to 20,000-ppb range is within ±2 ppb or ±0.4 pct, whichever is greater. The minimum detectable helium-4 concentration is calculated to be 5 ppb. The analyzer consists of a modified helium leak-detector mass spec-trometer, a laboratory-built sample inlet system, and a liquid-nitrogen-cooled charcoal trap. A programmable integrator and event-control module make automatic operation possible. The portability of the analyzer allows it to be used in the field.

Jan 1, 1984

By Eleanor Sonley

In October 2000, temporary seismographic stations were installed above the Trail Mountain Mine, Emery County, Utah, USA to supplement a regional network. Over seven months, 1826 mining-induced seismic events were recorded with a magnitude range of M 0 to M 2.2 (Arabasz et al., 2002, 2005). Routine event locations for this dataset cluster around the longwall mining activity during the recording interval. However, applying a double difference relocation technique to the routine locations significantly improves the correlation between mining activity and event location. The resulting relocations depend greatly on station distribution and the number of arrival time picks. We use this dense temporary array to assess station distribution requirements for applying the double difference technique at other mines by systematically removing data from available stations, thus simulating sparser networks. The insight gained using the Trail Mountain dataset is used to develop a metric for assessing the usefulness of above-mine networks and to develop a tool for expanding seismic network coverage. To verify the appropriateness of these tools for wider application, we examine data from two additional mines located in the western United States. Improving the relative locations of mining-induced seismic events highlights the association of these events with active portions of the mine. Clusters, regions of quiescence and relative timing of events can be used by mine operators to assess hazard, optimize production, and evaluate performance of mine plans. The lessons learned from this study may be used in future network design to improve accuracy of event locations at other mines.

Jan 1, 2009

By A. J. Kraemer

This report is one of a series dealing with oil-shale-operations in foreign countries visited and studied by Bureau of Mines oil-shale technologists within the past 4 years. Many oil-shale deposits have been discovered in Brazil and studied with various degrees of thoroughness. In this report the major emphasis is upon the oil-shale concessions of Companhia Nacional de Oleos Mineraes, in the River Valley of the State of Sao Paulo, because this oil-shale deposit is one of the most promising in Brazil for large-scale utilization for the manufacture of liquid fuels and other products of oil-shale processing, and because the opportunity was afforded to examine the concession area and to study mining, retorting, and. refining operations on these shales. Results of detailed analyses at the Oil Shale Research and Development Laboratories of the United States Bureau of Mines, Laramie, Wyo., are reported, Analyses and other date dealing with other oil-shale deposits in Brazil have been compiled from many sources. As many data have been reported as could be correlated to indicate the range of variation of the several types of shale end similar material. The oil-shale deposits in Brazil differ widely in size, richness of the shale, and of the oil. Some deposits are situate& more favorably for exploitation than others.

Jan 1, 1950

By Paul Clark

Generation - Profile l 9,726 megawatts (MW) of capacity l 46,877 gigawatt hours (GWh) produced at an average plant availability of 88.4% l 47 facilities in four geographies: Canada; the U.S.; Mexico; and Australia l Fuel mix of coal (62%), gas (26%), hydro and renewables (12%) l 23.2 million tonnes of coal mined l 47.0 million gigajoules (GJ) of gas consumed

May 1, 2004

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries to remove iron and sulphur from the molten matte phase. This technology has not changed significantly since its inception in the early 20th century. The typical converting operation involves lateral purging of air/oxygen-enriched air into molten matte through a bank of tuyeres. This blowing operation occurs at low air pressure from the blowers, and the induced bubbling regime is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks include recurrent tuyere blockage, inevitable tuyere punching operation to clear airways, and low oxygen efficiency as a result of substantial air losses due to leakages.Investigations in the 1980s demonstrated1 that jetting into Cu and Ni converters could reduce or eliminate some of the process difficulties. In spite of these findings, very little progress has been made in the application of these concepts for converting of non-ferrous melts on a commercial scale.As part of its operational improvement and energy reduction initiative, Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to full-scale industrial evaluation, a numerical assessment was conducted to ascertain the feasibility of implementing sonic injection on Lonmin converters. The work included flow characterization at high injection pressures achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid (VOF) and realizable k- e turbulence models to account for the multiphase and turbulence nature of the flow, respectively. These models were applied using the commercial CFD numerical code FLUENT.This paper discusses the key findings regard ing understanding of gas plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a fullscale implementation of sonic injection in the smelter."

Jan 1, 2014

By G. Avramovic-Cingara

Grain boundary characteristics and microstructural evolution are analyzed in a comparative study using orientation imaging microscopy (OIM/SEM) and transmission electron microscopy (TEM/SAD). The subgrain sizes and misorientations were determined by the OIM for aluminum deformed in torsion to equivalent strains between 0.2 and 4 over the temperature ranges of300-600°C and strain rates 0.01-1 s". The OIM gives clearer evidence of boundaries with high misorientation than does TEM, but it overestimates their frequency b y missing boundaries less than 1 0. T EM more clearly reveals low-angle arrays of widely spaced dislocations resulting in finer subgrain sizes than those indicated by OIM. The evidence supports a mechanism combining dynamic recovery (DRY), deformation band formation with permanent boundaries and geometric dynamic recrystallization (gDRX) in contrast to the hypothesis known as continuous dynamic recrystallization (cDRX).

Jan 1, 2004

By Tuncel M. Yegulalp, Malcolm T. Wane

In general, many problems relating to the exploitation of mineral deposits are probabilistic in nature. This derives from the fact that the geologic universe is inherently random. Probability theory and statistics have been found useful for forecasting the behavior of natural events that occur in the geologic universe. The objective of this paper is to illustrate the application of the theory of extremes to this fore-casting problem. For example, it is customary for design purposes to determine the rupture strength of geologic materials. The theory of extremes is exceedingly useful in describing that portion of the frequency distribution of rupture strength which contains the least strengths. Parameters describing the distribution of the least strengths are more important to the designer of mining excavations than parameters describing the total distribution. The basic principles of the theory of extremes will be detailed and illustrated. Any person required to work in the laboratory of nature is aware that uncertainty is a salient feature of all mining enterprises. A mining engineer required to plan the most efficient, practicable, profitable, and safe mine finds himself face to face with numerous ill-understood and often unquantifiable states of nature. Basic information necessary for adequate planning is often lacking or derived from incomplete tests on samples or experience of doubtful validity. The planning procedure usually takes the form of determining a feasible layout with the intent of determining an optimal layout when and if the necessary details and information become available. The crux of the entire procedure is the choosing of numbers to put into the operational and structural models which encompass the plan. Many times these numbers must be assigned qualitatively from past experiences and are called the "most probable ones." At other times, load records, performance records and material tests provide a basis for extrapolation. In any event, the numbers are chosen from a distribution or set of all numbers. Since each number in the distribution represents a possible state, the choice of any particular value is based upon a decision rule. To illustrate, consider the design of an underground structure or the design of a rock slope. The initial step is the formulation of the various possible structural actions which result from the geometry of the layout. For a given structural model various intensities of behavior are possible depending upon the load, deformation, and material characteristic spec-trums, respectively. Of particular interest to mining people is the failure behavior or condition, i.e., when there is a complete collapse of structural resistance by either structural instability or fracture. A necessary feature of the analysis is the "rupture strength" of the material. Information on the rupture strength is derived from testing either in situ or in the laboratory and the usual outcome is a variation in the test results. The methodology used to overcome this variation is to construct a frequency distribution of rupture strengths, and then determine a measure of central tendency and variability. The main idea involved is that the central tendency number will be used in the failure calculations and the measure of dispersion will be used to estimate the probability of failure. In particular if the distribution of rupture strength is normal, the mean rupture strength is the central tendency number and the standard deviation of the rupture strength is the measure of variability. Suppose the mean value of rupture strength is 1000 psi and the standard deviation is 200 psi. Insertion of 1000 psi into the failure calculation produces results that are unsafe, hence a common decision rule is to reduce the mean value by a "factor of ignorance" so that the failure calculation will produce a "safe result." If two is chosen as a factor of ignorance, this means the value inserted in the calculation is 500 psi or 2.5 times the standard deviation. The next step is to determine the percentage chance that failure will occur from a design created on this basis. Tables on the normal distribution function show that this percentage chance is 0.621% or approximately 7 times out of 1000. In practice, however, the situation is more complicated than represented by the foregoing illustration. The laboratory or field testing program usually constitutes a pathetically small sample of the geologic universe of interest and not enough testing is carried out to determine the exact form of the distribution of the test results. The normal, Cauchy and Student's T distributions are strikingly similar, and it becomes a matter of mathematical convenience to assume the normal law for phenomena which follow other laws.

Jan 1, 1969

By P Gleeson, J Coombes, P Suresh, T McLennan

The last 20 years have seen a dramatic rise in the use of 3D visualisation and modelling for geological data, but there has been relatively little effort to do the same for the variogram models that underpin the standard estimation algorithms used by the mining industry.For kriging, one of the most used geostatistical estimation methods, specifying a variogram model is a critical part of the modelling process. Experimental variography is the primary method for approximating the theoretical variogram function from the available sample data, and then determining an appropriate variogram model from the approximations.The traditional tools used for experimental variography are limited to looking at subsets of the data and are often presented without reference to geographic space and geology. It can be difficult to know what input data is being used for a particular experimental variogram, and whether there is enough support in the experimental variograms to propose an appropriate model.To overcome these limitations, an innovative approach called situational variography has been proposed that visualises variograms in 3D alongside contextual geological and geometric data. Presenting variograms in this manner aids understanding of how the spatial variance relates to the underlying data.A 3D extension of the 2D radial variogram maps will be investigated which allows for dynamic exploration of the full experimental variogram cloud. These 3D experimental variograms are much easier to visualise situationally.A workflow for situational variography will be outlined and the advantages of the situational approach will be illustrated using a porphyry copper deposit.CITATION:Gleeson, P, McLennan, T, Suresh, P and Coombes, J, 2017. Situational 3D variography – determining the variogram in the context of geology, in Proceedings Tenth International Mining Geology Conference 2017, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By T. Malvik

Norway is a big producer of ferrosilicon and silicon metal. The raw material is quartz and quartzite and large quantities from both Norwegian and foreign sources are used. The demands maade on both the chemical purity and the thermomechanical qualities of the quartz/quartzite have increased in recent years in an attempt to reduce energy consumption and to improve utilization. Control of the chemical quality of the raw material is relatively easy by means of routine analysis, but it is more difficult to find a suitable method for testing the thermomechanical properties. A rapid test method to define high quality quartzite deposits for use in the metallurgical industry has been developed. The method is based on a combination of chemical analysis, dilatometry, thermosonimetry and cathodoluminiscence.

Jan 1, 1989

[Aamot, Olav Crone, (M'29) Chem. Engr., Elektrokemisk, Raadhusgt. 23, Oslo, Norway. Abadilla, Quirico A., (M'38) Min. Engr., Dir. Bureau of Mines, Manila, P. 1. Abbott, Agatin, (J'40) Asst. Geol., Trench Mine, Patagonia, Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Tennessee Coal Iron & R.R. Co., 1642 Brown Marx Bldg., Birmingham, Ala. Abel, Raymond L., (M'28) Prof., Chem. Engrg., Univ. of Pittsburgh, Pittsburgh, Pa. Abel. Walter D., (M'32) Min. Engr., Div. of Corporations, State of Calif., 403 California State Bldg., Los Angeles, Calif. Abele, Louis T., (M'31) 4800 Patterson Ave.. Richmond, Va. Abell, Leo M., (M'31) Research Met., Mount Morgan Ltd., Mount Morgan, Queens., Australia. Abenius, Hakan V., (M'37) c/o Falu Gruva, Falun, Sweden.]

Jan 1, 1940

By Charles T. Holland

In connection with the problems of bumps in coal mines, much has been written concerning the manner in which roof action and methods of mining enter into the pressure effects observed but little has been written upon the relationship between the physical properties of coal and associated rocks and the cause of bumps. The question of the strength of bituminous coal, of its elasticity, and the energy it can absorb and store has been neglected to a considerable extent in connection with this problem. It is generally agreed that one of the necessary conditions for bumps is a strong coal.' Therefore, since the strength of coal is an important factor, a study of this property should be made. several investigators have conducted laboratory experiments upon the strength of coal, using small cubical or rectangular test pieces. An attempt will not be made to go into all of these investigations, but they are briefly summarized in Table I. Experiments of the U. S. Bureau of Mines and of Lawall and Holland (pp. 27 and 34 of ref. 9), however, indicate that regardless of whether the coal is a soft and weak semihituminous (Pocahontas No 3) or a hard and strong bituminous (Stockton) coal, the maximum ultimate unit stress developed in laboratory tests is higher in small cubes than in larger cubes of the Same coal.

Jan 1, 1942

By V. Patarini, M. Salkind

BECAUSE of its high strength and stiffness coupled with low density, continuous boron filament is showing great promise as a potential reinforcement for both metals and nonmetals. Of primary consideration for structural applications is the fatigue behavior of boron fiber composites. Composite fatigue behavior is dependent upon three factors: 1) fiber fatigue behavior, 2) matrix fatigue behavior, and 3) the effect of the interface and fiber ends. The purpose of this note is to describe the behavior of boron filament in rotating beam fatigue. The filament, described by Talley' and Galasso, Salkind, Kuehl, and Patarini,' was made by the hydrogen reduction of boron trichloride on a hot tungsten filament. Testing was performed using a commercial rotating beam wire fatigue tester* described by Votta.~ One end of the test sample is held in a chuck in a synchronous motor. The sample is bent around in a "U" shape, and the other end inserted into a carbide bushing. The maximum strain occurs at the bottom of the "U" where the radius of curvature is a minimum. The strain is adjusted by adjusting the length of the specimen and the location of the bushing. Samples were rotated at 3600 rpm and an automatic shutoff device used to determine the number of cycles to failure. The measurements were accurate to the nearest 360 cycles. The fatigue behavior is summarized in Fig. 1 for fifty-one samples of 4.8 x 10"3 in. diam fibers and ten samples of 3.2 X 10"3 in. diam fiber. The two sample groups represent two different filament production runs and two different nominal size groups. Both groups exhibited nominal tensile strengths of 400,000 psi. No significant difference in the fatigue behavior of the two sample groups is apparent. The scatter in the data is not unexpected for a brittle filament which exhibits a tensile strength distribution with a standard deviation of 10 to 15 pct. Because the test procedure provides a known outer fiber strain in the sample, the maximum stress was calculated assuming a Young's modulus of 58 x 10' psi. This value was selected as being representative of several nominal fiber sizes.2 All of the samples which failed exhibited sudden, catastrophic fracture, and no permanent deformation. One sample was stopped after 1.66 x lo8 cycles at *200,000 psi. The fiber exhibited no apparent damage or deformation. It is apparent that the fatigue resistance of boron filament is quite good. It can therefore be speculated that the fatigue behavior of boron fiber composites would be controlled by the "weaker links", namely matrix fatigue resistance and interface behavior. In fact, preliminary investigations have revealed that this is true for boron-reinforced aluminum? It should be noted that the data presented herein may not necessarily reflect the tensile fatigue behavior of boron filament. It is well-known that boron filament has a radial residual stress pattern with the outer surface in ~om~ression.~ Because of this fact, tensile failure is normally nucleated in the interior of the filament.5 Since the data presented herein is for a rotating beam test in which only the outer surface of the fiber is stressed to the maximum value, it would be incorrect to assume that the failure mechanism and fatigue behavior would be the same if the fiber were tested in tensile fatigue. The fact that many of the data are well above the nominal 400,000 psi tensile strength would tend to support this argument. The authors would like to express their appreciation to the United Aircraft Research Laboratories for supporting this investigation and for permission to publish the results. A portion of this effort was supported by the Air Force Materials Laboratory under contract AF33(615)-2125.

Jan 1, 1968

"Sampling error and bias, especially the Increment Preparation Error (IPE), are introduced when the tool allocated to do the job fails to extract a representative sample. This is the case with chip sampling; the tool can only extract haphazard shapes of loose or fractured material and not always from within the demarcated sample area. Increment Extraction Error (IEE) and Increment Delimitation Error (IDE) could be severe, but are found to be relatively unbiased. The uncontrolled action of the sampler in discarding excess sample material after sample collection has a significant impact on the error and bias introduced with each and every extraction. A new type of bias, referred to as the ‘waste discard bias’, arises when samplers select what portion of the excess sample material to discard at the sample site. Material visually identified as waste is discarded in preference to mineralized broken ore if there is an excess of sample material. This results in a considerable error in the analytical results. The bias is proportional to the reef-waste ratio in the demarcated sample. IntroductionTwo types of ‘sampling’ are distinguished, namely sampling of particulate materials (broken ores) and sampling of solid, unbroken in situ mineralized reef. This study considers only chip- or face-sampling of in situ, goldbearing, carbon-rich conglomerates typical of the Upper Witwatersrand Supergroup and examines where components of sampling error and bias, clearly specified in the Theory of Sampling, may arise during the practice of ‘face sampling’. Many millions of face samples have been extracted from Witwatersrand-type mines using a hammer and chisel, and detailed descriptions (standard operating procedures) of how the samples should be taken have been developed by many mining companies. There is, however, no taxonomy or nomenclature for managing or reporting the different types of errors associated with chip sampling. The Theory of Sampling compiled by Pierre Gy in the early 1950s provides, comprehensive nomenclature of sampling errors that is applied to particulate sampling of ore in a lot, a stockpile, or a moving stream on a conveyor belt. The taxonomy and characteristics of sampling errors, grouped according to the sources from which they arise, and identified by Gy (1973, 1979, 1982, 1992, 1995, and 1998) are shown in Figure 1. This classification of errors is used extensively in regard to the sampling of particulate materials in the mining and minerals industry, but not in regard to chip sampling. A relatively small mass (hundreds of grams) of representative particulate material for estimating the average grade of a much larger mass (thousands of tons – the ‘lot’ in the Theory of Sampling) is extracted by the chipping or cutting of a representative rock ‘sample’ from the stope face."

Jan 1, 2016

By I. Iwasaki, P. L. De Bruyn

Electrical double-layer properties of the silver sulfide-solution interface in different electrolytes and the influence the properties exert on the adsorption of dodecylammonium acetate (DAA) were studied using an electrochemical titration technique. The flotation behavior of silver sulfide was observed using DAA as collector and the results were correlated with adsorption measurements. Silver and sulfide ions were identified as the potential determining ions and their adsorption densities were measured as functions of the pAg and of the ionic strength at two different pH values. The point-of-zero-charge (PZC) was observed to be at pAg 10.2, the value being independent of pH and of the nature and concentration of the electrolyte used. The surface charge of silver sulfide in these electrolytes was positive for pAg values less than 10.2 and was negative for pAg values greater than 10.2. The adsorption of amine on silver sulfide surfaces at pH 4.7 was found to be strongly dependent on the pAg. A shift in the PZC towards a lower pAg due to the adsorption of amine indicated a specific affinity of dodecylammonium ion towards silver sulfide surfaces. At pH 9.2 a strong adsorption of the undissociated amine molecule was indicated. The PZC shift towards a higher pAg and the adsorption of the amine was virtually independent of the interfacial electrical conditions.

Jan 1, 1972

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials Closed-circuit grinding, classification, hydroseparation, flotation, agitation, and thickening are familiar terms at this cement plant These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements Construction of the plant, haying originally a design capacity of 7000 bbl of cement per clay, was started in June 1939, and the first clinker was ground on the following Christmas Day At present the capacity is about 12,000 bbl of finished cement per 24 hr , most of the production being low-heat cement † About 3130 tons of limestone, 620 tons of clay and 100 tons of gypsum are required daily for this output Occasionally iron oxide is added to the clay to obtain the desired composition This, together with the gypsum, is purchased from outside sources Up to the present time, the corporation has produced low-heat, normal, moderate¬ heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements Most of the present production is for Shasta Dam, near Redding, Calif , the told demand being 5,800,000 bbl of cement Following are sonic of the cement requirements of the Shasta D [im] specifications [ ] The average specific surface in the bin s sampled shill be not less Ulan 1800 sq cm per gram and no individual sample less thin 1600 sq centimeters Compressive strength The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2 75 parts fine testing sand, by weight, shall be equal to or greater thin the following

Jan 1, 1941

By Richard Akerman

At the International Sessions of the Iron and Steel Institute of Great Britain, the American Institute of Mining Engineers and the Verein Deutscher EisenhUttenleute, held in Allegheny City, Pa., in October, 1890, Sir James Kitson, then President of the Iron and Steel Institute, presented an account by Sir Henry Bessemer of the origin of the process which bears his name.? The paper graplhically told how, after the first successes immediately following the first reports given at Cheltenham of the new process, there rapidly succceded such obstacles and difficulties in its practical application, that the whole matter was nearly abandoned in 1858. Suddenly, however, the situation changed, so that at length it became possible

Jan 1, 1894

By L. Eaton, A. W. Last, J. L. Stevens

COPPER ore from Kennecott Copper's Ray mine, about 60 miles southeast of Phoenix, Ariz., is concentrated at the company's mill at Hayden, some 18 miles south of the mine. The Hayden mill is currently treating 16,000 tons of ore per day by flotation, using raconite, a crude butyl xanthate, as a collector for the sulfide copper minerals and lime as a pyrite depressant.1 The ore contains significant amounts of nonsulfide copper minerals, but recovery of these values has been low. The Hayden mill is now being modified to provide for treatment of future ores by leach- precipitation-flotation (L-P-F). This modification, costing about $5 million, is expected to reduce the loss of nonsulfide copper values and improve overall copper recovery by an additional 2 lb per ton of ore.

Jan 11, 1957

By John W. Cahn

The spinodal has long been regarded as a limit beyond which a homogeneous phase could no longer be metastable. But only recently has it become apparent that a phase beyond the spinodal would decompose by simple diffusional clustering mechanism quite different from the nucleation and growth mechanisms encountered for metastable phases. The theory of spinodal decomposition, which is based on the diffusion equation modified by thermodynamic requirements , is phenomenological, and each parameter can be measured by independent thermodynamic or diffusion experiments. The details of the theory have been carefully verified in a number of simple systems. It appears that the spinodal mechanism is commonly encountered in clustering reactions in solids and glasses. HISTORICAL INTRODUCTION The understanding of the earliest stages of precipitation in alloys has been the subject of three prior Institute of Metals Lectures. In 1932 Paul ~erica' reviewed the puzzling evidence that hardening of duralumin is completed before precipitation of CuAlz takes place and suggested that hardening occurs when the copper atoms "assemble in random groups on lattice positions of the duralumin, not of the CuAlz lattice". He called these random groups knots. This modification of his dispersion hardening theory seemed to fit all the facts, but Merica worried that the required diffusion "is just the reverse of what we deem normal; although quite spontaneous, it proceeds uphill, if you please". The reality of Merica's knots was quickly confirmed by Guinier's' and preston's3 X-ray work and these knots are today known as G.P. zones in their honor. Theoretical justification for uphill diffusion was also quickly provided by Becker and Dehlinger~ who noted that the diffusion coefficient could be negative in certain regions of phase diagrams. The boundaries of such regions could be described by a 90-year-old thermodynamic concept first described by ~ibbs' in 1877 as a limit of metastability for fluid phases, which by 1890 had received the name spinodal (see Appendix A). Spinodal in fluids is as old as nucleation theory. Both appear for the first time in the same paper by Gibbs who called the spinodal the limit of metastability. For the first 50 years, nucleation theory was forgotten and the spinodal was extensively treated in every good thermodynamics textbook.81Q The idea was simple and logical and it was accepted as part of a rigorous thermodynamic development of metastable phases, and for a while it was extensively investigated theoretically.

Jan 1, 1969

By L Soares, W T. Hennies, F Fujimur

Barra Bonita reservoir, located in the Sao Paulo State, Brazil, has been mainly used for local navigation and electricity generation to supply a prosper region in the country. Sand mining activities in that area have an important social and economic meaning for the local community. In this reservoir there are several sand mines that produce around 45 000 m3 of sand a month. These deposits were rich in material used as concrete aggregate in the civil construction. However, nowadays a significant increase in the demand of gravel can be observed, representing a serious productive problem. This material hasnÆt been well accepted by the market and, through the years, it was disposed at open sky in piles as waste deposits. This deposits have caused environmental problems like visual impact, reduction of free spaces outside and inside the mine, source of material to erosion and sedimentation processes in lower areas, flooding as a result of the filling up process in the drainage system, among others. For a lack of an appropriate technological characterisation, this material have been mainly used to pavement internal and external areas in the mine, with lower cost associated. With the purpose of evaluate the usefulness of this material in the conventional concrete, there were conducted several tests in the disposed residue including petrographical, physical, and chemical characterisation. The petrographical analysis and the preliminary results of the study showed that the material reacts with the alkalis that are present in the conventional cement (CP-II-E-32). In order to make the application technical and economically possible a research was developed seeking forms to correct this characteristic by adding special cements with high pozzolana content. The results of the technological, physical and chemical characterisation of the products indicated the technical viability of the use of that material. The study also allowed projecting environmental improvements resulting in the elimination of the waste piles.

Jan 1, 2003

By Fred D. Wright

In this paper the principal theories used to design roof bolting systems are presented and discussed. Then the characteristics of various types of roof bolts are presented and finally the interaction between rock and roof bolt characteristics on choice of roof bolts is discussed. Theories can be considered design tools which may or may not be appropriate for a specific situation. It is good for a design engineer to have a number of such tools available and also important that he understand their good features as well as their limitations. Hence, some of the principal theories and classification systems used for design of roof bolting systems are discussed first.

Jan 1, 1982