Search Documents

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"ABSTRACTTheoretical approach to estimate the ultimate pile capacity gives a rough idea at the initial stage of design that later on strengthen by the execution of static pile load test at site. The static pile load test is the only best option for the estimation of ultimate capacity of various types of piles. There are various methods based on strength, serviceability, net deflection for end bearing, shaft adhesion, graphical and extrapolation approaches for the interpretation of pile load test data to calculate the ultimate capacity. In this paper an attempt is made to evaluate the best-fit method for the estimation of ultimate capacity of single helix screw pile. The pile load tests on model scale were performed on screw piles of different helix diameter. The purpose of adopting model scale of testing was to achieve a state at which settlement increases without further increase in vertical load. The ground was compacted with dry sand at denser state. It was observed from the test results that extrapolation methods such as Chin- Kondner and Decourt predict the load settlement curve of screw piles very well, however ultimate pile capacity was on higher side which may not be suitable for the strength of helix plate. Decourt approach to plot the pile load data showed clear indication of the deformation of helix due to strong subsurface condition. A modified approach in Decourt method is proposed for estimating the ultimate capacity of screw pile having deformed helix whereas reduction factor is suggested for Chin-Kondner method for the estimation of ultimate capacity of intact screw pile.INTRODUCTIONDeep foundations are used to avoid the soft ground at shallow depth that is not suitable for carrying the structural load. Different types of piles have been used to transfer the load to deeper stratum. The screw pile is one of the new piling method and its use is considerably increasing. It consists of a cylindrical steel shaft with one or more helices at various length of the shaft. The diameter of helices (Dw) is usually 2 – 2.5 times the shaft diameter (Ds). The pile is installed to the required depth through torque and pressure. The advantage of screw pile over other piling system is its quick installation mechanism, high end-bearing and uplift resistance, noise reduction and minimum use of man power."

Jan 1, 2014

The general principles of technical due diligence best practice that are involved in assessing a mineral property in the early stages of its development are described and a bibliography of relevant papers is attached. The issues specific to the evaluation of gold deposits are highlighted. The Australasian Institute of Mining and Metallurgy's (The AusIMM) initiatives in this area, dealing with the proper public reporting of Reserve/Resource information (JORC Code) and property assessment/valuation (VALMIN Code), will be used as a framework against which the illegal tampering with drilling samples to artificially boost their gold content (salting) from the Busang gold deposit (Kalimantan, Indonesia), owned by Bre-X Minerals Limited (Calgary, Canada), will be reviewed. While the Busang saga was based upon fraud, through salting the samples, the general lessons to learn from such a scam are worth documenting. In Australia, most of those working in the mineral industry belong to long established professional institutes and consultant associations (eg The AusIMM or Mineral Industry Consultants Association [MICA]) that require their members to work within their technical limits and to comply with best practice guidelines, or risk being judged and found wanting by their peers in the context of strong Ethics Codes. There is also a strong interface between such representative professional bodies and the corporate and financial market regulators (ASC/ASX), which closes the monitoring loop. Canada has only now seen the wisdom of having this type of early warning system in place. Fraud and deliberate deception will be always possible, but deception on the enormous scale that occurred at Busang is most unlikely with proper surveillance systems in place and the use of accredited technical professionals. There should have been more hard data available about so big and rich a deposit owned by a C$6Bn company.

Jan 1, 1997

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the US. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and air- ways that must be maintained for the life of the mine. This is because roof, even the best of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof because the previous equilibrium is upset, resulting in pressures that cause fractures and slight movements that are frequently hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned: the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but can vary from inches to 6.1 m (20 ft) or more. There are examples of where there is no immediate roof as the massive main roof lies directly on the coal

Jan 1, 1981

By H. M. Kim, J. Rutqvist, D. W. Ryu

"Demand of high pressurized gas storage in underground rock caverns is increasing. Compressed natural gas (CNG) and compressed air energy storage (CAES) are one of the promising examples after since lined rock cavern (LRC) concept has been verified through in-situ pilot tests. Two key essential concerns of high pressured gas storage in underground rock caverns are mechanical stability of the cavern against high inner storage pressure and the risk of gas leakage from the caverns.In this study, we introduce our results of numerical simulations so as to investigate the potential of monitoring for gas leakage at a pilot facility for CAES in underground LRCs. The pilot facility was constructed at a comparatively shallow depth of 100 m, compared to the previous cases with several hundreds of meters, aiming at validating the feasibility of the LRC storage concept in which inner sealing liners, consisting of steel plate and concrete linings, are installed inside the excavated rock caverns (KIGAM, 2011). Compressed air may leak through either initial defects of inner containment liners such as imperfect welding regions and in-situ construction joints of the liners, or through structurally damaged points of the liners during the CAES operation where compression and decompression of the caverns are necessarily repeated and their structural robustness can be deteriorated.For this perspective, we carried out a coupled thermodynamic and geomechanical deformation analysis using TOUGH-FLAC simulator, and investigated the effectiveness of strain monitoring method in detecting mechanical failure of liners which may provide major pathways of air leakage. We therefore used an equivalent continuum model to relate the localized tangential strain to fracture permeability changes, which was developed in our early work (Rutqvist et al, 2012). In detecting and characterizing the leakage location, we tested a cross correlation technique using the synthetic pressure responses monitored in case of the failure of the inner liners. From the investigations, we showed that tangential strain, rather than radial, monitoring especially at the inner face of the sealing liners can be more effective in detecting the mechanical failure of the liners.In localizing the leakage point, we noted that the interface between the inner liners and surrounding rock may not be perfectly bonded so as to increase permeability through which any leaking air pressure may migrate more dominantly. We also demonstrated that the cross correlation of the time histories of pressure measurement especially at these interfaces can be useful in identifying the leakage point. These results may provide useful information in overall design of monitoring and alarming system of our upcoming CAES pilot facilities."

Jan 1, 2015

By Theodore J. Williams

Computer control has been one of the fastest moving and most glamorous fields of industrial development in the past decade. A review of this period shows some truly remarkable accomplishments in both system development and applications. In addition, work now under way promises results which will continue the rate of progress of the past. This paper will review the history and status of the field of computer control and point out the major breakthroughs which have occurred. It will analyze the present trends and extrapolate them to predict the early future developments in the field.

Jan 1, 1968

By H. V. R. Von Rahden

The expertise of the industrial mineralogist has not always been sufficiently used in decision-making in the minerals industry in South Africa. The mineralogist can make a contribution at al stages of the exploration programme, from the time of discovery of a geological target area, through metallurgical testwork and pilot-plant studies, to the production of a saleable product. This indicates that the activities of the industrial mineralogist should be more closely integrated with those of the exploration geologist and the extraction metallurgist in order to provide management with a meaningful picture of the economic potential of an ore deposit.

Jan 1, 1997

Jan 1, 1977

By F. A. Forward, A. H. Ross, J. Halpern

Application of the carbonate leaching process to carno-tite ores has often been limited by the difficulty of obtaining simultaneous high recoveries of uranium and vanadium. The chemical aspects of this problem are discussed and the effect of prior roasting procedures on this discovery is described. IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to ±15°C. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO8 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi 02. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1959

By J. F. Enrietto

It is shown that one cannot approximate the broad internal friction Peaks observed in the Fe-Mn-N system as the sum of a number of subsidiary Peaks and still vetain the concept of a single relaxation time. Furthermore, the approximation of manganese affectirg only nearest neighbor interstitial sites is shown to be incompatible with the experimental results. The results of this experiment show that the influence of manganese in the ferrite lattice extends over 3 to 4 atomic distances. NUMEROUS experiments have shown that the presence of relatively small amounts of substitutional alloying elements can profoundly affect the profile of the damping spectrum in the vicinity of the Snoek peak in bee metals.1-7 Dijkstra and Sladekl observed this phenomenon in Fe-Mn-N alloys where it appeared as a broadening and shifting of the Snoek peak to higher temperatures. The authors interpreted this as being the result of a superposition of two damping maxima—the normal Snoek peak, located at its usual position and having a normal half-width, and an interaction peak having a normal half-width, but occurring at a somewhat higher temperature. They prclposed that the interaction peak was caused by nitrogen atoms jumping from Fe-Mn sites to Fe-Fe sites, the Fe-Mn interstitial sites having one manganese and one iron atom as nearest neighbors, and the Fe-Fe sites having two iron atoms as nearest neighbors. They further suggested that the Fe-Mn sites had a lower energy than the normal Fe-Fe sites because of the presence of the adjacent manganese atoms. From the relative heights of the two postulated damping peaks, the dif-

Jan 1, 1962

By Phillip J. Mackey, Gerardo R. F. Alvear F.

It is now 38 years since the publication of the first edition of "Extractive Metallurgy of Copper" by Professor W.G. Davenport and the late Professor A.K. Biswas. The text book would be issued in a total of five editions, soon became the standard for students and those in industry. Interestingly it was published at the onset of great change in the industry. This was a time when sulphur dioxide controls in the USA were introduced, and almost simultaneously, world oil shocks caused significant increases in the cost of fuel - all leading to efforts to adopt new technology and move away from the reverberatory furnace, which had no potential for sulfur capture and required large amounts of fuel. At the time of publication of the book, new processes such as the Noranda Process and the Mitsubishi Process were in their infancy, while flash smelting (which was first commercialized in 1949 at Harjavalta, Finland) had made significant in-roads in boosting copper output, with some 22 new flash smelters licensed by 1976. Computer technology and associated process control techniques were rudimentary compared to systems today, available physico-chemical data remained largely in tabulated format and needed to be manually entered into the main frame computers of the era, while modeling techniques common today had not yet been developed. The copper industry has therefore seen immense changes since the time of this textbook: world tonnage of smelted copper has risen from 7.34 million tonnes/year in 1976 to 16.7 million tonnes/year in 2012, over a two times increase. Technologies such as the El Teniente Process, or Top Submerged Lance technologies, typified by the ISASMELTTM, not commercialized at the time, now treat large tonnages of copper concentrate in a single furnace. Advanced heat and mass balance software and thermochemical modeling are now used extensively to examine chemical and physical characteristics for process design and to support process optimization. These changes in the industry have been chronicled in subsequent editions of the book. This paper looks at the issues and problems seen in 1976 and over the intervening years, and compares this with the challenges facing the industry with the available tools and technologies today. Some ideas looking into the future are also discussed in the paper.

Jan 1, 2014

By G. F. Friel

A series of experiments in the U.S. Bureau of Mines Safety Research Coal Mine at the Pittsburgh Research Center evaluated the effects of crosscuts on the travel time of carbon monoxide (CO) along an entry to improve the accuracy of a mine-fire locator program. Three entries, ten single crosscuts, and three double crosscuts were instrumented with CO sensors. One-percent CO in nitrogen was released and monitored as it traveled the entries. In addition to dispersion of CO at the front of the CO wave, CO was entrained from the entry into the crosscuts. It was determined for an entry and single-crosscut configuration that the measured travel time for a concentration change of 5 ppm was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and crosscut volumes. For an entry and double-crosscut configuration, the measured travel time for the same concentration change was 25% greater than the predicted time based upon entry volume only, but 10% less than the predicted time based upon entry and crosscut volumes. An effective dispersion coefficient for CO dispersion along one of the entries was estimated to be 1.5 m2/ s.

Jan 1, 2010

By F. Bourgouin

Thirty-one years ago, African leaders met in Lagos for the drafting of the Lagos Plan of Action for the Economic Development of Africa, 1980?2000. The main objective of the plan was to increase Africa?s self-sufficiency and in this regard, the plan had a section pertaining specifically to redressing the ills of an unproductive mining and minerals industry and harnessing its potential for socio-economic development. However, if we look at the nature of this sector on the continent today, its characteristics resemble the diagnosis of the sector given in the plan back in 1980: lack of information on endowments of minerals; lack of value added in the sector; low development and use of those endowments that are not of interest to transnational corporations (TNCs); and most importantly, low contribution to socio-economic development. The primary consequence of the lack of visible benefits to African states, despite growth and development of the sector in terms of increased mining activity led by Foreign Direct Investment is that countries with mining industries are characterized by dysfunctional internal processes. Improvements in governance, monitored with indices such as those set out in the Extractive Industries Transparency Initiative, the Millennium Development Goals, and other such ?good governance? agendas, are being asserted. However, before we prescribe the introduction of initiatives or guidelines based upon highly subjective norms which we believe to fit this diagnosis, it is necessary to review how it is that we got to this situation that we are in today. How is it that, 31 years after the Lagos Plan of Action, we have not seen any major changes in the role the industry can play in socio-economic development, despite the vast increase in mining activity on the continent?

Jan 1, 2011

By Rohrbach

Crosshole Sonic Logging (CSL) testing is commonly used to verify the integrity, quality and ultimately the acceptability of the concrete in structural elements such as drilled shaft foundations, secant pile cutoff walls, and secant/tangent pile earth retention structures. Besides concrete quality, many factors can impact CSL test results (e.g. laitance, air temperature, access tube spacing, access tube debonding, etc.). Effective use of CSL testing requires fully informed qualified practitioners capable of distinguishing between abnormal readings unrelated to deficiencies in the drilled shaft concrete and similar readings indicating the presence or possible presence of drilled shaft defects. Based on data and experience gathered from CSL testing of thousands of drilled shafts across North America, this paper discusses such factors and other information useful when evaluating CSL test results, and provides practical recommendations intended to reduce the potential for incorrect test data interpretation. The CSL testing industry is lacking in a clear, universally accepted guideline for the interpretation of CSL data and acceptance criteria of these concrete elements. This paper proposes terminology and a streamlined process for use when atypical results are obtained. The proposed terminology and method are intended to simplify and expedite the submittal review and approval process. Because construction activities for these elements are often on the project?s critical path, the benefits obtained in terms of project savings and reducing costly delays are undoubtedly valuable.

By Koginmo V. I

The concentrator at Bougainville Copper Limited has an annual throughput of 48.2 million tonnes/year producing approximately 175,000 tonnes copper, 16.1 tonnes gold, and 50 tonnes silver. Conventional three stage crushing and screening are used to reduce run of mine ore to an average product d80 size of 6.7mm. The primary objective of the crush- ing plant is to provide a continuous supply of ore to the 12 primary grind- ing mills via an intermediate 300,000 tonnes capacity stockpile. Since ball mill performance improves with decreasing mill feed size, the crushing plant continually strives to produce the finest possible product for mill- ing. This has been achieved by increasing plant availability and total installed power, and improving crusher manganese liner life, screen cloth life, and plant operating practices. A recent innovation was the installa- tion of a 35 million tonnes/year preconcentration screening plant in Janu- ary 1987 to recover high grade fines from low grade run of mine ore types in which the mineralisation occurs preferentially along fracture planes in the parent rock.

Jan 1, 1988

By Jonathan Tsang, Ali Merati, Jonathan Beddoes

Due to economic factors, many aircraft in service today have been operating for more than 30 years even though they were initially designed with a service life of 20 years. Improved damage management models are therefore needed for use in life prediction and management of the aging fleets of aircraft. Currently, the generally accepted procedure in fatigue life prediction methodologies is to back calculate the equivalent initial flaw size (EIFS) using established long crack growth data. However, it was observed from studies carried out at the National Research Council Canada that nucleation and short crack growth constitute up to -95% of the fatigue life. As a result, it seems that the significance of the short crack regime has been underestimated and must be further investigated and fully understood before an accurate holistic life prediction methodology can be realized. Unlike long cracks, local microstructural features such as grain boundary, grain size, inter-particle spacing, and texture play dominant roles in the behavior of short cracks. An extensive study has been carried out to evaluate different crack detection and monitoring techniques in the short crack regime for AA2024-T3. The results will be presented in detail.

Jan 1, 2004

By L. J. Lutz

The U.S. Bureau of Mines has developed an electrorefining process to recover Ni, Co, Cr, and other metals from mixed and contaminated superalloy scrap. The superalloy scrap is cleaned then directly electrodeposited as a Ni -Co deposit. The process recovers approximately 90 pct of the Ni-Co available from the scrap as a 99t pct pure Ni-Co alloy. During electrorefining the electrolyte undergoes a purification process which results in Cr and other refractory metals reporting to the purification residue. Operating data is given for a 3-L compartmented electrolytic cell. Techniques for the removal of Fe, Cr, and trace impurities from the recycled electrolyte are outlined. The economics of a facility producing 15 mt/d of a Ni-Co alloy are also discussed.

Jan 1, 1993

"1 INTRODUCTIONThe use of nondestructive testing (NDT) methods to evaluate the integrity of Augered Cast-in-Place (ACIP) and Drilled Displacement (DD) piles has been a subject of significant debate among engineers, contractors and NDT practitioners. This guideline document will illustrate the importance of reviewing all available information in conjunction with the NDT records. ACIP and DD piles have unique properties that must be considered when using a specific NDT method. Any evaluation of the integrity of an ACIP or DD pile must also include a thorough review of the detailed pile installation records and the site specific soil conditions. Long or theoretical descriptions of the methods have not been included in this publication. More detailed information about these NDT methods including their theoretical and historical backgrounds can be found in DFI’s Manual for Non Destructive Testing and Evaluation of Drilled Shafts (2004). Additional information can also be found in the more comprehensive textbook Nondestructive Testing of Deep Foundations by Hertlein and Davis (2006).1.1 PurposeThe intent of this guideline is to provide practical guidance for the proper interpretation of NDT results on ACIP and DD piles. Short descriptions of the main integrity methods available are provided along with several examples of how to use all of the information available to make sound engineering judgments about the results. This publication is a state-of-the-practice guideline to promote accurate engineering evaluations.For engineers inexperienced with NDT, these guidelines provide sufficient background information on NDT methods to help understand the limitations of the testing, assess the results presented to them, and formulate appropriate questions. This is particularly important for engineers charged with the responsibility to determine from those results what, if any, consequences there may be on the performance of the structure under construction."

Jan 1, 2016

By J. R. Budden, P. A. Spencer, J. Barrett

The initially produced arsenic (III) is very toxic to the unconditioned culture but the mixed culture has the capacity to oxidise it to arsenic (V) in the presence of iron (III). It was possible to build up the resistance of the culture through progressive sub-culturing on arseno-pyrite until it could tolerate steady-state concentrations of 30 mM arsenic (III) and 200 mM arsenic (V). With some samples tested in the continuous systems the final arsenic concentrations reached 330 mM. It proved possible to use the laboratory batch data to establish the optimum operating conditions for continuous test systems with capacities of up to 32 m3. Data on the residence time, oxygen uptake rates and gold extraction from the bio-oxidised residues could then be confirmed by continuous testing without the need first to use empirical means to determine optimum conditions for continuous bio-oxidation. The data on residence time, oxygen uptake rate, solids density and neutralisation could be used to estimate the capital and operating costs of treating any given tonnage of the concentrate of interest. It was established that the arsenopyrite concentrates can be suitably bio-oxidised to cause the liberation of at least 90% of the gold content. The method is simple to operate and is flexible over a wide range of external conditions

Apr 1, 1991

By Almon F. Robertson

This is one of a series of reports describing investigations made within the Missouri River Basin in Montana by mining engineers of the Bureau of Mines, Minerals Division, Region II. The primary purpose of these investigations is to provide basic information to agencies of the Department of the Interior and other agencies concerned with the planning of power and other water developments in the Missouri River Basin. This report contains only such factual data as have been authorized for public distribution. Special precautions have been taken not to reveal any information or data considered to be confidential. The field investigations for this report were made during the fall of 1948 and the summer of 1949. Virtually all of the known metallic mineral deposits and some nonmetallic (industrial) mineral deposits within Judith Basin County were investigated. Most of the mines and prospects have been inactive for many years; most of the old underground mine workings now are inaccessible or only partly accessible. Consequently, much of the information on many of the mines and prospects necessarily has been obtained from available U. S. Government and State publications and from owners and local residents.

Jan 1, 1951

This paper is a summary of the general theory of sampling published by the author in 1975. Sampling is a random process and its the- ory is a study of the, numerous errors liable to take place in the course of its realization. A complete sampling scheme is a sequence of sampling (proper) and preparation stages . At each stage, the total error ET is the sum of : -.Sampling errors EE arising from the selection process itself. -Preparation errors EZ arising from the operations (crushing, transfer...) sup- ported by the sampled material. ET a EE + EZ . At each sampling stage, the (total) sampling error EE is the sum of seven inde- pendent errors : - Weighting error ED resulting from the non-uniformity of the density or rate-of-flow of the sampled material. - Integration error EI1 resulting from the long-range distribution heterogeneity of the sampled material. - Periodicity error EI3 resulting even- tually from periodic quality variations of the sampled material.

Jan 1, 1976