Search Documents

By Shad M. Sargand, Manseok Chang, Glenn A. Hazen

Customarily, peak particle velocity of surface wave vibrations has been the recommended criterion for the prediction of blast damage to structures. Currently blast spectrum and natural frequencies of a structure have been also recognized as important for predicting damage potential. While others have considered the importance of structural frequencies, they have not analyzed the structural response spectrum when establishing damage criteria.

Jan 1, 1992

Carbonation of reinforced concrete is a potential durability issue for vehicular tunnels. This is particularly the case where elevated carbon dioxide concentrations exist and when the design life is 100 years or more. The process of carbonation can result in loss of passive protection to embedded steel reinforcement and initiation of corrosion. Therefore, tunnel design needs to consider the potential for carbonation on internal surfaces and how design life can be achieved in severe environments. This paper examines methods for predicting carbonation and how deterioration can be mitigated through appropriate concrete mix design and construction practices.

Jan 1, 2008

By J. H. Viljoen, N. B. Strydom, J. S. Greyson, C. H. Van Graan

SYNOPSIS Bad eyesight and poor illumination can contribute to the occurrence of accidents in mines. As one part of a study of this problem, surveys of light intensities have been conducted in 19 gold mines. On 17 of the mines the surveys were on one underground level only, whilst in two of the mines more intensive surveys were conducted by measuring light intensities in all areas to determine any inter-mine variations between the levels of illumination. Readings of light intensity were taken underground at stations, tips, winches, stopes, conveyor belts, waiting places, pump stations, fitters' and boilermakers' workshops, ambulance rooms and in haulages. It is concluded that the average levels of illumination in South African gold mines are comparable with those reported in the literature for mines elsewhere. Standardisation of lighting conditions underground could eliminate inter- and intra-mine variation in illumination levels where they occur. A guide to mine illumination practice would assist such standardisation, and help increase the levels and effectiveness of illumination in mines. Some suggestions are made in this latter connection.

By E. V. Kuzmin

The rock properties improvement means the exchange of natural properties: increase of stability, strain and compress tension, reduction of gas-liquid filtering property, increase Jung- module, other mechanical and physical parameters of rocks by injection the hardening materials, such as polymeric pitches, micro-or geocements by special technology under high pressure, to fill cracks. Flow of liquid materials between the rock units and hardening under high pressure create full redistribution of rock pressure in rock massif. There are many reasons to use this technology in underground mining, tunnelling, creation barrier technology in raioactive, chemical and other danger material site etc.

Jan 1, 1996

By V. C. Pandolfelli, L. Paulino, C. E. Zangiacomi

The continuous improvement in aluminum industry over the last years has increased metal output at lower cost. The potlining plays an important role in this regard due to high cost involved and more recently in its environmental aspects. In order to increase potlife and thus minimize the aluminum cash cost, a systemic approach is needed, through investigating the main cathode failure mechanisms by using a pot autopsy as a powerful tool, and then making the necessary chances to achieve extended potlife. In addition, preheating and pot start-up may also damage the cathode if not performed with an appropriate technique or even if the lining materials are not specified correctly, among other factors. All these aspects will be presented and discussed in this paper. Increased potlife, especially now that the current is reaching values up to 300kA, will allow aluminum plants to match their goals more efficiently at lower costs.

Jan 1, 2006

By R. Augsten, K. K. Feng, K. C. Cheng

"Methane emission and the desorption characteristics of vertical borehole coal samples of Greenhills multiple seams in the vicinity of Elkford, British Columbia were investigated. Three vertical boreholes at depths of 335 m, 380 m and 395 m were drilled along the west wall of an active open pit mine and 44 core samples from various coal seams were obtained for desorption studies.The results are presented in three tables and illustrated with six figures. The methane content was found to increase significantly at depths greater than 200 m. The adsorption equation by Kim and the properties of the coal have been used to predict the methane content and these were compared with the measured values by the direct method.IntroductionThe coalification of plant material in the sedimentary rock produces different ranks of co al and gases of various composition. The gas mixtures are retained in coal beds and rock strata under pressure. The gas content in a coal bed varies considerably depending on the rank of coal and the depth of overburden. The gas content is defined as the volume of gases adsorbed in a unit weight of coal materials. The net amount of gases remaining in a coal seam depends on the difference in the rate of generation of methane by geo-thermal heat and the rate of diffusion of the gases out of the coal bed through sedimentary cover. The major factor that causes the change in rank and the liberation of gases is the temperature, which is governed by the thermal conductivity of sedimentary cover and the heat flux through the underlying rocks. The rate of diffusion of the gases out of the coal is governed by the porosity of the overlying rocks and the degree of fracture. The measured values of gas content in major North American coal beds are from zero up to 24 cm3 per gram of coal(1,2). A gas content of 2.5 to 9 cm3/g is considered ""gassy"" and that of 9 cm3/g or higher is considered ""very gassy"" for underground mining(3). Normally, the gas mixtures released from bituminous coal in Canada contain 90 to 98% methane and the remainder is made up of CO2, N2, 02, H2, He and other hydrocarbons(4)."

Jan 1, 1984

By Hideaki Kitajima, Daisuke Fukuda, Kazuma Moriya, Katsuya Sasaki, Katsuhiko Kaneko

The purpose of this research is to analyze the fracture process and achieve design optimization of a splitting method for concrete and rocks termed the electric discharge impulse crushing method (EDICM). The EDICM utilizes the cartridges being set in boreholes in the splitting target. The cartridge has a thin metal wire and is filled with nitromethane. By applying the electric discharge to the wire in the cartridge, plasma is caused leading to the vaporization of the wire. Then the deflagration of the nitromethane commences, which generates borehole pressure for splitting the target. Although the required splitting time is roughly several hundred micro-seconds and much slower than ordinary blasting, the fracturing still completes in quite short time and understanding the fracture process of opaque and brittle materials such as rock and concrete in this time scale is of academic importance.

Jan 1, 2011

By Gary Kahn

In this document the VODR is discussed from a technical point of view and is intended to give the reader a feel for the design of the instrument, its technical specifications, and its limitations. It is not intended as a tutorial on the use of the instrument in the field.

Jan 1, 1989

By A. P. W. Briggs

Difficulties with the screening of large volumes of pulp to remove plus 600 /km material before the adsorption circuit and to retain plus 20-mesh carbon in the adsorption contactors have largely been solved, with the result that the plant can now handle its design throughput. The elution and electrowinning processes have been modified to simplify the circuit, but the regeneration of carbon remains unsatisfactory. The production of fine carbon in the plant can lead to increased gold losses, and this carbon must be collected and treated. Collection methods for fine carbon and some indications of the quantity of the carbon and its gold values are given.

Jan 1, 1983

By Peter Hood

Data on world-wide geophysical activity in mining exploration programs are collected annually by the Society of Exploration Geophysicists' Geo-physical Activity Committee as part of a continuing service to the industry. The data are obtained by sending out questionnaires to all organizations which are known to be carrying out mining geophysical work; the organizations canvassed include mining companies, contractors, government departments and universities. The questionnaire is divided into three sections; namely, ground methods, airborne methods and research. The data compiled from the questionnaires show that world-wide utilization of mining geophysical methods reached a new high in 1967 with total expenditures of (U .S.) $32,323,240. This was divided as follows: ground methods, $18,106,785; airborne methods, $10,-123,405; and research, $4,093,050. For the ground methods, most money was spent on the induced polarization technique ($5,681,780); electromagne-tic methods were second in reported expenditures ($2,010,900). The total reported geophysical line mileage flown was 1,275,072 line miles, with aeromagnetic surveying being the most popular airborne method. The total amount spent on aeromagnetic surveys was $5,832,564 for 895,420 line miles. This gives an average cost of (U.S.)$6.50 per line mile.

Jan 1, 1968

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

"In order to make the stainless steel making process efficient and environment friendly, it is essential to minimize the loss of chromium to the slag phase. With a view to investigate the advantages of using CO2 to attain moderate oxygen partial pressures in the oxidant gas during the decarburizations of stainless steel, the present experiments were carried out to understand the oxidation kinetics of Fe-Cr alloys and Fe-V alloy with gas mixtures containing CO2. In the present work, the oxidation behavior of Fe-Cr and Fe-V was examined by thermogravimetric analysis (TGA). Various mixtures of O2 and CO2 were used as the oxidant gas and the oxidation rate was followed by the weight changes as a function of time.The experiments demonstrated that the oxidation rate is independent of temperature at present experimental situation, but has strongly related to the Cr-content of the alloy as well as the oxygen partial pressure in the oxidant gas mixture. The wetting of alumina by the iron drop and the change of the drop shape during the course of the oxidation were investigated by X-ray radiography."

Jan 1, 2010

By W. J. Whiten, D. W. Grinsberg

Most cluster analysis techniques are not well suited to the analysis of engineering data as they have been designed for more qualitative data that tend to produce compact clusters. A clustering technique is described which develops and uses local cluster shapes to build clusters that are suitable for use in engineering applications. The technique is finding application in the analysis of many types of data, particularly where multiple trends and outlying points occur in multiple dimensions. Applications of particular interest are the calibration of on-stream analytical equipment and the analysis of data on plant performance. In both cases the multidimensional nature of the data renders manual analysis very difficult

Dec 1, 1991

By P. N. Anyalebechi

"The effects of solidification rate, initial melt hydrogen concentration, and grain refining on porosity formation in aluminum alloy 2024 have been investigated with unidirectionally cooled laboratory-size ingots. The ingots were prepared from melts containing hydrogen concentration of 0.059-0.27 cm3/100 g and solidified at 0.2-37 °C/s. As expected, the amount of porosity, average pore size, and pore number density increased with increase in melt hydrogen concentration and decrease in solidification rate. However, the effect of solidification rate was greater at the very low melt hydrogen concentration (0.059 cm3/100 g). These results are consistent with reported effects of solidification rate and melt hydrogen content on porosity formation in other aluminum alloys. Interestingly, addition of grain refiner slightly increased the amount of porosity and the average pore size, especially at solidification rates above 1°C/s. IntroductionIn shaped castings and wrought products fabricated from ingots, billets, bars, or slabs of aluminum and its alloys porosity formation is a problem. This is because it compromises their tensile strength, fracture toughness, and fatigue properties [ 1-18]. The pores are usually the crack initiation and propagation sites [6,8,9] and the largest pores tend to dictate the fatigue life of the aluminum products [9,10,14]. Porous regions within an aluminum product probably yield first due to the reduced tensile load bearing capacity, causing the concentration of the strain near the voids which subsequently results in premature fracture. In aluminum alloy ingots, billets, bars and slabs porosity formation is particularly problematic because of its persistence through fabrication and potential for reappearance or exacerbation during subsequent thermal treatment processes before and/or after fabrication [19]. In fact, persistence of microporosity is a serious problem in large thick plates of wrought aluminum alloy products that must be rolled from correspondingly large direct-chill or electromagnetic cast ingots. Some of these thick plate products are machined into large aircraft components that are required in service to withstand multi-directional stresses and to possess high fatigue strength, fracture toughness, resistance to stress corrosion cracking, and strength in the short-transverse direction [1,20]."

Jan 1, 2011

By E. E. Bach

STATEMENT OF THE PROBLEM THE administration of industrial organization today embraces more than the cost of production and selling prices. Competition is deeper seated than mechanical devices, overhead charges, and a shrewd manipulation of the markets. Despite the "down-to-the-minute" equipment and the "last word in organization," it is quite evident that "capacity production" will be an unknown quantity until the workman is considered as a producer, in relation to his home, as he is now considered in relation to industry. Whether or not a man shall do an honest day's work is as much a psychological condition as it is a matter of physical strength or skill. His attitude toward his work each morning is determined, to a large degree, by the environment of his home. Whether this attitude, good or bad, obtains the day through will depend entirely upon the one fact as to whether the corporation which employs him does or does not differentiate between the mechanical factor and the human factor in industry. To be more specific, sociological work, under whatever name, should be of such a character as to influence the life of a workman in such a manner as to establish a cooperative interest in his work, foster within him a spirit of contentment in his home, lead him-so to employ his leisure time that he will not lower his efficiency as a workman, destroy his domestic happiness, or endanger his standing in the community as a citizen. While no fixed rules of procedure can well be formulated for the development of the work, yet definite lines of activities will readily present themselves as applicable to the individual needs of a community. This is especially true where community influences and agencies pertaining to general welfare are easily correlated.

Jan 2, 1918

By R. P. Laforce, ZJ. R. Low, A. M. Turkalo, D. F. Stein

The interaction of the crlloying eletnenls, nickel and chromium, with the impurity elements, antimony, pIzosphorus, tin, and arsenic, to producse reversible temper brittleness in a series of high-purity steels containing 0.40 wt pct C has been investigated. The alloyed steels contained approximately 3.5 pcl Ni, 1.7 pct Cr, and 0.05 to 0.08 pct of the particular irnpurity to be investigated. Susceptibility to teirlper embrittlement was measured by comparing the notched-bar transition temperature of each steel after quenching from the final temper and after very slow cooling (step cooling;) following the final temper. A plain carbon steel without alloying elements, bu/ ud/h 0.08 pel Sh, does not embrittle when step-cooled through the emzbrittling range of temperatures. The same embrittling treatment, applied to a steel with about the same antinzony content but with nickel and chvonziunz added, causes a 700°C increase in transition temperature. If chromium or nickel is the only alloying element, the increase in transition temperature is only 50%, again with antimony present. A carbon-free iron containing nickel, chromium, and antimony shou~s a 200°C shift in transition temperature for the same thermal treatment. Specific alloy-impurily interactions are also observed for the other impurity elements, phosphorus, tin, and arsenic. Additional investigations involving electron microscopy, trzicrohard-ness tests of vain boundaries, minor additions of zirconiutn and the rare earth and noble metals, nzainly with negative results, are also described. HE particular type of embrittlement investigated is that which is encountered in alloy steels tempered in the temperature range from about 350" to 525'C or slowly cooled through this range of temperatures when tempered above this range. This type of embrittlement is sometimes called reversible temper brittleness to distinguish it from the embrittlement indicated by a minimum in the room-temperature V -notch Charpy energy vs tempering-temperature curve encountered in the range 28 0" to 350°C. Temper brittle-ness seriously restricts the use of many alloy steels since it precludes tempering or use in the embrittling range of temperatures and may significantly raise the ductile-brittle transition temperature of heavy-section forgings and castings tempered above the embrittling range, since such sections cannot be sufficiently rapidly cooled after tempering to avoid embrittlement. The very voluminous literature of temper brittle-ness up to about 1960 has been reviewed by woodfine' and LOW.' Of particular significance to the present investigation was the demonstration by Balajiva, Cook, and worn3 that high-purity Ni-Cr steel does not exhibit temper brittleness and the subsequent detailed and systematic study by Steven and Balajiva~ of the effect of impurity additions on the susceptibility to embrittlement of Ni-Cr steels. Steven and Balajiva showed that, of the impurities which may be found in commercial steels, Sb, As, P, Sn, Mn, and Si could all produce temper brittleness in a high-purity Ni-Cr steel. The principal purpose of the present investigation was to study the effects of particular alloy-impurity combinations on susceptibility to temper embrittlement. The steels used were high-purity 0.30 to 0.40 wt pct C steels containing 3.5 wt pct Ni and 1.7 wt pct Cr, separately or in combination. The susceptibility of these steels was then determined when approximately 500 ppm by weight of antimony, arsenic, phosphorus, or tin were added as an impurity. The melting, casting, and forging practices used in the preparation of the materials investigated are described in Appendix A. Table A-I in this appendix shows the analysis of all steels to be discussed. The steels were produced as 20- or 2-lb heats. The smaller heats were used after it had been demonstrated (see Appendix B) that a small, round, notched test specimen could be used to measure the shift in the ductile-brittle transition temperature caused by temper brittleness with about the same result as that obtained by Charpy testing. HEAT TREATMENT Unless otherwise noted, all steels were tested for embrittlement in the tempered martensitic condition. A typical heat treatment for a 0.40 C, 3.5 Ni, 1.7 Cr steel was: 1 hr at 870"C, in argon, quench into oil at 100"C, quench into liquid nitrogen, temper 1 hr at 625"C, and water-quench. The warm oil quench was used where quench-cracking was encountered; otherwise the initial quench was into room-temperature oil or water. For other compositions austenitizing temperatures were 50°C above Acs with the remainder of the thermal cycle the same. Steels in this condition, with no further heat treatment, are designated as non-embrittled. The above quenching and tempering cycle for the 0.40 pct C steels resulted in as-quenched hardnesses of 48 to 53 RC and as-tempered hardnesses of 24 to 31 Rc except in the case of the plain nickel or plain carbon steels. In these, the as-tempered hardness was as low as 80 to 90 Rg. No attempt was made to adjust the tempering temperature to obtain the same hardness in ali steels since it was felt that a uniform thermal cycle was more important than exactly equivalent hardness values. Pro- the standard quench and temper described above, the standard embrittling treatment was "step-cooling". For this the thermal cycle was: 593"C, 1 hr; furnace-cool to 538"C, hold 15 hr; cool to 524"C, hold 24 hr; cool to 496"C, hold 48 hr; cool to 468'C, hold 72

Jan 1, 1969

By A. J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of steel wire ropes. Steel wire ropes are very suitable for mine hoisting due to their high strength and durability, but have the negative characteristic of a low strength/weight ratio. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength/weight ratio of synthetic ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application.

Feb 23, 2014

By S. J. Broderick

[The discovery in 1934 that carbonaceous materials, such as coal, peat, and lignite, when treated with concentrated sulfuric acid, were given cation or bate-exchange properties opened up a field of new materials with many interesting possibilities. These hydrogen exchangers, as they were called, were so superior to the impractical hydrogen exchangers made from natural and synthetic zeolites tat they were accepted immediately by the water-conditioning industry. A noteworthy advantage of the carbonaceous exchangers is that they are nonsiliceous, hence they do not give up silica to the water as do the natural and synthetic Zeolites, especially if the hard water is corrosive. For this reason the new exchangers found immediate favor in boiler-feed-water conditioning.]

Jan 1, 1941

By I. R. Stevenson, J. G. Dunn, T. N. Smith, L. C. Mackey

An experimental flash reactor has been developed to simulate the operation of an industrial flash-smelter reaction shaft. Four concentrate materials of differing mineralogical compositions were characterised and then oxidised in the reaction shaft. The products were examined by chemical analysis to determine the extent of oxidation and by electron-probe microanalysis to determine the fate of individual particles. This programme of work enabled the influence of mineralogical composition and particle size on the extent of oxidation to be assessed

Jul 1, 1991

By Keiichi Fujita, Katsumoto Ueda, Hiroshi Nakauchi, Naohiko Okumura

INTRODUCTION This paper presents (1) modified slipform system which was employed for simultaneous concrete placement for permanent lining and Instruction of a partition wall in the execution of a ventilation shaft 620m deep, and (2) current shaft sinking techniques which have been applicable and efficient for the subsurface conditions in Japan. MODIFIED SLIPFORM SYSTEM FOR PERMANENT LINING OF VERTICAL SHAFT General Information This paragraph deals with rapid construction by using modified slipform system for the permanent concrete lining and a partition wall of ventilation shaft, which has inside diameter of 620m and depth of 620m, of Enasan Highway Tunnel. The general feature of the shaft is illustrated in Fig. 1 and standard section of the shaft is illustrated in Fig. 2. The geological condition surrounding the shaft is mainly of ryolite and surface is of talus, but as a whole, they are rather weak and weathered rocks with faults, fissures and clay seams. 220mm borehole for the geological investigation was used as a drainage hole, predicting the amount of water inflow into the shaft to be 10t/min. The shaft was executed mainly by means of the conventional short step sinking method of 1.2m lift, employing temporary headframe and hoists. For each lift, 40 to 50cm thick temporary concrete lining was used. About 28,600m3 of rocks were excavated and

Jan 1, 1979

By J. W. Spretnak, G. W. Cunningham

Grain growth across the bond region in Pressure bonded copper was found to be mainly dependent upon the presence or absence of microvoids, but it was also found that prior history, bonding pressure, bonding time, and bonding temperature are important variables. An increase in pressure, time, or temperature tends to promote grain growth in the interfacial region. Polygonization is observed after pressure bonding except for specimens previously annealed at temperatures on the order of 1800°F or higher. The dislocation density in bonded specimens was found to be greater in the bond region. THE bonding of metals by the application of gas pressure at elevated temperatures is a relatively new process, having been developed over the past 10 years. The technique, as described by Paprocki, Hodge, and Boyer,l is unique in that assemblies of many parts and complex shapes can be bonded with a negligible amount of deformation. The process thus differs metallurgically from pressure welding, cold welding, and recrystallization welding in that deformation occurs only in a microscopic region whereas, in general, the welding requires severe deformation and may extend the contact surface by a factor of 3 to 10 during the welding. From a practical standpoint, pressure welding is not amenable for bonding large surfaces. During the time in which Paprocki and coworkers were deve1oping the process, West2 established aproc-ess,for bonding aluminum to uranium, and Barnes and Maze? developed a gas-pressure-bonding technique for nickel and copper. Recently, Fugardi and Zambro4 have used equipment similar to that developed by Paprocki and coworkers to establish parameters for bonding stainless steel, aluminum, and zirconium. Most of the investigations on pressure bonding have been empirical in nature and, although methods have been developed for bonding such metals as molybdenum, columbium, titanium, zirconium, and stainless steel, the information concerning the mechanism of bonding is limited. Several workers5"7 have studied the pressure bonding of dissimilar metals in order to gain information on diffusion and formation of inter-metallic phases under application of pressure. Clapson and Robbins8 have shown by a series of annealing studies that voids in the interfacial boundary of roll-bonded copper can prevent movement of the boundary until the voids are spaced far enough apart to prevent pinning. They also indicated that recrystallization and grain growth can eliminate the voids. In this paper it is shown that voids are the major detriment to grain growth across pressure-bonded interfaces, but it is also shown that prior history, bonding pressure, bonding time, and bonding temperature are

Jan 1, 1962