Search Documents

By Watsford R. M S, Hutton R

Following the delineation of significant extra ore reserves during 1990, the decision was made to expand production from 350,000 tonnes of run of mine ore per year to initially 600,000 tonnes increasing to 750,000 tonnes per year. The existing plant consists of a conventional three stage crushing plant followed by a heavy medium separation plant that produces a product prior to grinding. Grinding is conducted in three stages of ball mill in series. Alternatives examined for expanding production included: aò SAG mill - ball mill circuit replacing the secondary and tertiary stages of crushing, the heavy medium plant and the existing ball mills; and, upgrading of the existing circuit configuration.

Jan 1, 1991

There has been disappointingly little development in the analysis of rock slopes in open pit mines over the past 30 years. A brief review of literature shows that the application of numerical stress analysis methods to open pit mine slope stability has become only relatively common in recent times, and that there are as yet no standardized approaches. The lack of development in general, and of robust, standardized approaches in particular, is surprising in view of the ?ultra? deep open pit mines that are being developed to depths in excess of 1000 m. In this paper, the results of a substantial programme of two dimensional and axisymmetric analyses of open pit slopes are described. Variations in the following parameters were taken into account in this programme: slope angle, slope height and horizontal to vertical in situ stress ratio. The evaluation of the data has concentrated on the tensile stresses and the extension strains in the slopes. This is believed to be the first publication dealing with strain distributions in slopes. The occurrence of zones of tensile stress was very limited. These zones occur in the crests of slopes, except in the case of low horizontal to vertical stress ratios, in which case the tensile zone is in the floor of the pit. In contrast, very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. The large zone in which such extension failure could potentially occur in a 1200 m deep pit is typically more than 100 m horizontally behind the toe and about 400 m up the face from the toe. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning. Such ?strain bursting? produces easily measurable seismicity, events often being audible as well. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. With suitably orientated joints, extension strains are likely to manifest themselves in the opening up of such joints and hence in the loosening of the rock mass in a preferential orientation, with potential effects on groundwater flow patterns.

Jan 1, 2003

Jan 1, 1925

By J. A. Herbst, D. W. Fuerstenau

An analysis of the kinetics of dolomite grinding in a dry ball mill reveals that the following approximations apply for the parameters of the batch grinding model: (1) the size discretized selection functions are proportional to the specific power input to the mill, and (2) the breakage functions can be taken as invariant. These approximations are shown to provide the basis for accurate predictions of product size distributions obtained for several mill speed, ball load, and particle load combinations within the normal ball mill operating range. The engineering implications of these findings are discussed.

Jan 1, 1974

By S. Escoffier, A. Giraud, K. Su, F. Homand, N. Hoteit

Abstract For the feasibility study of an underground waste disposal the characterization of the coupled behaviour of the host rock is required: Because of the very low permeability of these formations few experimental data are generally available. In this framework the uses of the sensitivity studies could orient the experimental efforts by highlighting the key parameters of the formation. This paper gives a first approach of the sensitivity studies performed with probabilistic methods in the geomechanical field. A one dimensional model which characterizes the thermohydromechanical response of an argillaceous rock to the excavation of a waste canister site and its setting up, is considered. Zusammenfassun Die Machbarkeitsstudie eines tiefliegenden Endlagers für radioaktive Abfälle beinhaltet die Untersuchung des gekoppelten Verhaltens des im Lagerbereich anstehenden Gesteins. Aufgrund der sehr geringen Wasserdurchlässigkeit dieser Formationen liegen häufig nur wenige experimentelle Angaben vor. Die Verwendung von Sensibilitätsstudien kann in diesem Zusammenhang als Hilfsmittel zur Entscheidungsfindung dienen. Dabei sollen die maßgeblichen Eigenschaften der Formation festgestellt werden, anhand derer der Umfang der experimentellen Erkundung festgelegt werden kann. Dieser Artikel stellt einen ersten Ansatz zur Durchführung von Sensibilitätsstudien mittels einer mechanisch-probablistischen Kopplung im Bereich der Geomechanik sowie die Vorteile gegenüber Parameterstudien vor. Zur Abbildung des thermohydromechanischen Stoffverhaltens von tonigem Fels während der Schachterstellung und der Einlagerung der Abfälle wird ein eindimensionales Model verwendet. Résumé L'étude de faisabilité d'un centre de stockage de déchets radioactifs en profondeur passe par la caractérisation du comportement couplé de la roche hôte. Du fait de la très faible perméabilité de ces formations, souvent peu de données expérimentales sont disponibles. Dans ce cadre l'utilisation d'études de sensibilité permettrait d'orienter les efforts expérimentaux en faisant ressortir les caractéristiques primordiales de la formation. Cet article présente une première approche de la réalisation d'études de sensibilités à l'aide de couplages mécano-fiabilistes dans le domaine de la géomécanique. Un model unidimensionnel caractérisant la réponse thermohydromécanique d'une roche argileuse au creusement d'un puit de stockage et à la mise en place de conteneurs de déchets est considéré.

Jan 1, 2003

By Sang-Su Lee

This paper shows the application of the porous plug system in the Mitsubishi continuous copper smelting and converting process. This system has already been adopted and utilized in the steel industry to enhance productivity. Recently, some copper smelters have adopted this system but the results have not been satisfactory. The porous plug system was installed at the anode furnace in December 2001 to reduce the oxidation time and decrease the oil consumption. A good effect was that the nitrogen stirring of the melt through porous plugs improved the melt heat transfer. As the result of the enhancing heat transfer the oil consumption and the build up inside the furnace were actually decreased. But until now the oxidation time has not been sufficiently reduced. In the future, further research and tests are needed in order to increase the productivity and save costs.

Jan 1, 2003

Floor heave events in underground mining often happen suddenly and cause risk to workers and equipment. Reducing the risk of floor heave must be addressed in mining layout design. To improve that design one must understand the significant parameters that are correlated to the occurrence of floor heave. To accomplish that goal, researchers from the National Institute for Occupational Safety and Health (NIOSH) completed a numerical study using FLAC3D, taking advantage of its strain softening and ubiquitous joint capabilities to better simulate the floor heave and caving mechanisms involved at an actual mine site.

Jan 7, 2020

By M R. Drumond

The present work presents a new theoretical interpretation of the flotation process, which can also be applied to other mineral processing physical unit operations. This interpretation is part of the æModelo OperacionalÆ (Operational Model) that was developed as an attempt to establish a new theoretical basis for mineral processing unit operations. In the case of flotation, a book was edited by one of the authors in Brazil (Mass Concentration by Froth Flotation, in Portuguese and Spanish).The model establishes a link between a natural phenomenon (migration of particles from the pulp to the froth) and a real industrial phenomenon (mass concentration by operational interference). In this model, flotation is viewed as a phenomenon of macromolecular mass transport (of particles) between froth and slurry phases. Mechanisms for mass transport and particle flow between phases as a function of the hydrophobic potential in each phase are discussed. By establishing the so-called equilibrium distribution curve between phases it is possible to calculate macroscopic balances that are related to metallurgical results, which in turn are a function of the operational line that is required by the process itself. The number of cleaning stages and their efficiencies can also be determined by simple laboratory-scale experiments.

Jan 1, 2005

By Filip Rochette, Yvan De Busscher

Extraction of minerals can be achieved by a variety of technologies; one of them is ion exchange. There are several ion exchange configurations and mechanical set-ups available, but only one technology will provide more process performance and flexibility compared to the other. The multiple column Continuous Countercurrent Ion Exchange (CCIX) technology provides the highest form of process flexibility with also the highest mineral recovery feasible through ion exchange. In comparison with a fixed bed system, the PuriTech CCIX system offers the benefits of continuous counter-current contact mode. This way the resin capacity is fully exploited leading to reduction in resin inventory and, at the same time, in chemicals and water consumption, and product dilution. For any set of operating conditions the mass transfer zone has a characteristic length (MTZL). The MTZL can be expressed in duration, column length, or volume, but is the measure of the quantity of resin in the system that is doing "work" at any given moment in the process. The objective of continuous ion exchange processing is to eliminate all resin volume from the process equipment that is not within a mass transfer zone. In most commercial ion exchange processes for the recovery of metals, CCIX engineering can eliminate as much as 20 - 80 % of the ion exchange resin inventory. Consumptions of water and chemicals are typically brought down around 40% or more. For each type of resin the selectivity/affinity towards a particular metal depends on the basic process conditions such as pH, concentrations of other competing metals in solution. By changing the pH in the ion exchange process phase, the selectivity of the resin can be changed. By doing this, a split elution, or extraction of metals separately can be achieved and the effect of other competing metals (cross-contamination) can be reduced. For example the DOW resin XUS43578 is commonly used for the recovery of copper or nickel/cobalt separation.

Jan 1, 2016

By Bill Sayer

Cadman, a wholly owned subsidiary of Heidelberg Cement, is a leading supplier of sand and gravel as well as ready mix concrete in the greater Seattle area in western Washington State. Cadman's aggregate mine is located in North Bend, 34 miles east of Seattle, WA, and consists of a "Lower Pit" and an "Upper Pit." In 2005, Cadman planned the upgrade of the North Bend mine operation as follows: Upper Pit (Figure 1): 1. Crushing Plant, Stacker and Stockpile 2. Storage Reclaim Belt Feeders 3. Feed Conveyor 4. Downhill Overland Conveyor Lower Pit (Figure 2, Photo 12): 1. Radial Stacker 2. Storage Reclaim and Truck Load-out

Jan 1, 2008

By C. E. Taylor, L. V. Fegan

With on-stream electrical-resistance measurement as a basis, Bethlehem Steel developed a system for the completely automatic control of moisture in the feed to pelletizing. This system was later successfully adapted to the sintering process, with automatic control of moisture serving to maintain the air permeability required for effective burnthrough. Control of moisture content is an important factor in the agglomeration processes by which iron ores are converted into either pellets or sinter for use in blast furnace burdens. In both pelletizing and sintering the iron ore feed must be mixed with the proper amount of water so that capillary attraction and surface tension forces can be utilized to cause the ore particles to coalesce and form larger agglomerates. The success or failure of the entire pelletizing or sintering process depends on maintaining the proper moisture. Therefore, continuous automatic control of moisture is one of the conditions for the automation and optimum use of both pelletizing and sintering processes. In pelletizing, variation in moisture can cause ball size to change and is a common cause of cycling which results in a fluctuating feed to induration. Excessive moisture can cause lumps to form at the cutter bar and contributes to the formation of buildup on the green pellet screens. Green pellets with excess moisture deform and reduce bed permeability. In sintering, accurate control of moisture is also important because moisture must be within the limits that give the bed the required permeability for good burnthrough. In response to these problems, a moisture meter, based on the principle of electrical resistance measurement, was developed. This moisture meter has been a key factor in the development of systems for providing uniform feed of concentrates in most of Bethlehem's pelletizing and sintering plants. The automatic moisture control system for pelletizing was successfully plant-tested and resulted in the following: (1) Control of moisture in the green pellets to +0.2%. (2) Up to 50% reduction of bentonite consumption. (3) Control of unscreened green pellets so that 85% of the furnace product at Cornwall was within the size range of -5/8 +3/8 in. (4) Improved quality of product with a tumble test of 94 and a "Q" index of 90 as the result of feeding a consistently uniform feed to a shaft furnace. In sintering, where sinter-mix temperature change and variable feed could cause errors in moisture measurement, the system was designed to maintain the correct moisture under virtually all plant operating conditions. It was successfully plant-tested and is now in use in most of Bethlehem's sintering plants. The system achieves: (1) Control of moisture within the desired limits for optimum production. (2) Continuous measurement and control of moisture even with intermittent feeding of mix, so that attention by the operator is seldom required. The two automatic control systems provide smoother startup, minimize upsets and contribute to the consistent control of process variables in pelletizing and sintering. MOISTURE-CONTROL SYSTEM FOR PELLETIZING Fig. 1 shows the general arrangement of the system for automatic control of moisture in pelletizing.1 In this system a bin level controller, using a single probe which regulates filter speed, maintains a uniform low concentrate level in the bin.' The moisture meter, comprised of an analyzer and control components, continuously measures the moisture in the bed and adds water to adjust to the desired level. The meter is placed in an open-loop (feed-forward) control, i.e., water addition occurs downstream from the probes. Filter vacuum must be set so as to produce a filtercake moisture which is below the optimum for pelletizing. Bentonite is added after the

Jan 1, 1969

Jan 1, 1915

By Wieslaw Blaschke

The transformation of Polish economy, has contributed to the significant ownership changes and the way of management. Most of non-ferrous metals producers are now joint stock companies or stock companies, which shares are owned mostly by Polish shareholders, the State Treasury, banks or trading companies. However, as compared to the international tendencies, the cost of production of base metals in Poland are still relatively high, and the utilization of secondary sources is still very low. In this sense, the paper point out that some positive results of the current pro-ecological mineral policy in Poland have been already clearly visible in the case of non-ferrous metals smelters, where the emission of dusts and gases was significantly reduced. Therefore, if the current increasing tendency of world production of non-ferrous metals continues, Poland’s role as their primary producer will be reduced.

Sep 13, 2001

By S. J. Frank

The development of feedforward semi-empirical control models for furnaces and the evaluation of mass balances are based on plant data. The models can only be as good as the data and it is therefore required to know the inherent uncertainty associated with the plant data. This uncertainty stems mainly from the fact that the slag, alloy or dust, have a distributed nature that depends on the degree of mixedness. It is commonly accepted that melts from open bath furnaces are well-mixed, and submerged arc furnaces less so. The impact of this assumption is significant, as a reasonably homogeneous melt could be represented by one sample only. As so much of metallurgical control depends on the assay information of the alloy and slag melts from furnaces, it was decided to characterise the possible variation in melt chemistry and temperature. Sampling campaigns and continuous temperature measurement of the melts were performed for different alloy and slag taps at a major ferrochrome producer. Both a submerged arc furnace and open arc furnace are evaluated in this way, by way of comparison. The slags of both open arc and submerged arc furnaces were found to be of similar degrees of homogeneity, with much spatial variance in the reducible iron and chromium oxides. However, it was found that the alloy melts deriving from open arc furnaces were significantly less homogeneous than the alloy derived from submerged arc furnace alloy production. The compositional variance could be related to the furnace operating conditions and it affects both metallurgical accounting and process control. In all cases it was found that the variance in melt solute components are larger than can be ascribed to analysis instrument error. It will be shown how this predetermined variance in melt composition could be included in process modelling and control.

Jan 1, 2004

By T. H. Alden

Using alternating tension-compression straining, the hardening of magnesium oxide single crystals was studied up to large stresses and strains. At 0.25 pct plastic strain amplitude, the hardening curve is approximately linear with slope 25,000 psi from the shear yield stress, 7 to 8000 psi, to 35,000psi. Above this stress, the slope decreases. The strain hardening behavior of MgO is considered qualitatively similar to that of metal single crystals. The relatively high stress attainable by strain hardening is associated apparently with the high yield stress on the cross-slip system, (001) <110>. Cleavage fracture during testing is uncommon. It is argued that the centers of high internal stress at glide band intersections, at which cracks tend to nucleate, are dispersed by cyclic strain. Special features of the glide band structure produced by cyclic strain and revealed by dislocation etch pits, support this view. Strain hardened MgO has mechanical properties greatly superior to the as-received material: yield stress, greater than 100,000 psi; elongation to fracture about 1 pct. A material is said to strain harden if the yield stress increases with an increment of plastic strain. This definition is usually applied for straining done in one direction, but is also applicable when the strain direction is periodically reversed, Fig. 1. For certain metal single crystals, data are available which permit a comparison of the hardening behavior for cyclic straining and for tension straining.&apos;-4 With certain qualifications, these data show that the same processes of hardening are operative in each type of test.5 Despite this fact, the importance of the technique is not immediately evident, although tension-compression studies of the common metals appear to suggest some deficiencies in theories of strain hardening developed exclusively on the basis of tensile tests. However, a recent observation suggests that the cyclic straining method may be very useful for studying semibrittle crystals in which large plastic strains are not accessible in unidirectional testing. The observation is that zinc crystals, when strained in tension-compression at -52°C, do not fail by cleavage at low stress (-500 psi)6 as they do in tension, but harden to a limiting stress of more than 5000 psi over a total plastic strain of about 600 pct.2 An important characteristic of the behavior of zinc crystals is the high stress, relative to the yield stress, attainable by strain hardening. By comparison, the hardening of aluminum single crystals tested by an identical technique saturates at 1100 psi. This difference is best explained by the cross-slip hypothesis of dynamic recovery.7,8 In zinc, cross slip is difficult because of the high yield stress for glide on planes other than the basal plane in the < 1120 > zone. The present work was undertaken in order to test whether these methods and ideas are applicable to other materials. Magnesium oxide single crystals, in common with most crystals of the rock-salt structure, deform plastically but fail by cleavage after a small strain when tested in tension. It was hoped that larger strains would be attained using tension-compression. There is, in addition, evidence 8a which shows that slip on the probable cross system, (001) < 110>, is difficult in magnesium oxide; it may therefore be possible to attain high stresses by strain hardening. 1) EXPERIMENTAL PROCEDURE Experimental methods used in this study were based in part on techniques reported in papers of Stokes, Johnston, and Li.&apos; MgO blocks, purchased from Norton Co., were used without further annealing. Specimens were cleaved to dimensions approximately 0.125 in. sq and 1 in. in length. The gage section, formed by chemical polishing, was sprinkled with 280 mesh silicon carbide particles in order to introduce fresh dislocations. The crystals were then cemented into cylindrical aluminum adapters and clamped in an Instron testing machine. One of two alternating straining programs was used. In the first, total cross-head travel was established and increased in steps after various numbers of cycles. In the second, a capacitance gage was used to directly measure the elongation of the specimen and the crosshead was controlled so as to keep the plastic strain amplitude constant. The straining was always symmetrical with respect to the initial, zero strain condition. While both procedures produce strain hardening, only the latter permits a measure of the total plastic strain so that hardening curves may be drawn. Constant plastic strain amplitude tests were done

Jan 1, 1963

By Khaled Morsy

The studied mine extracts the Sewickley seam using room-and-pillar method. The overburden at study site ranges from 400 to 800 ft. Eight years earlier, the Pittsburgh seam was mined 80 ft underneath the Sewickley seam. Parts of the mains at the study site experienced problems of rib spalling associated with floor heave. Numerical modeling was used to explain the mechanism of ground control problems encountered at the mains of the upper seam. The modeling results show that the ground control problems encountered were caused by multiple seam interactions with the previously mined longwall panel of the lower seam. Based on the modeling results, a criterion to predict the probability of multiple seam interactions was proposed.

Jan 1, 2006

By F. B. Henderson, D. Bird, P. L. Hauff, E. C. Prosh

A National Aeronautics and Space Administration (NASA)-funded project (NASA Grant #NAG13-02026) is underway to determine the ability of hyperspectral remote sensing to map mineralogy that affects water quality within a watershed and to identify the relative contributions of natural and anthropogenic sources to that drainage. Natural sources, particularly areas of pyritic hydrothermal alteration, have been found by the Colorado Geological Survey to be a significant source, sometimes the only source, for acidity and/or metals in a number of areas of Colorado (Neubert, 2000). This situation undoubtedly occurs in many places in the Western United States and elsewhere where metallic mineralization occurs. Anthropogenic sources arise from mining and other human activities that increase the exposure of acid-generating materials to weathering processes, thereby increasing acidity and metal loading to drainages where that activity is occurring or has occurred. This project is attempting to determine if these sources can be differentiated through mineralogical analysis, in conjunction with surface water chemistry that controls the precipitated minerals, of the impacted drainages by remote sensing techniques.

Jan 1, 2003

By Fabio Lerbach

The Powder Charcoal Injection in the main burner of the rotary kiln of Pelletizing Plant aims to reduce natural gas consumption and consequently cost reduction with thermal energy. This paper presents the technology, the injection process and the advantages of using powder charcoal to substitute natural gas.

Oct 30, 2017

By Yong-Moo Cheong

When the zirconium pressure tube(PT) is in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature gradient between the inner and outer wall of the PT results in a thermal diffusion of hydrogen(deuterium) and hydride blisters are formed on the outer surface of the PT. Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in a PHWR, there is a strong incentive to develop a method for the non-destructive detection of the blisters grown on the tube surfaces. However, because there is little mismatch in an acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and the zirconium matrix with the conventional ultrasonic methods. This study has focused on the development of an ultrasonic method to detect the hydride blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of a Zr-2.5Nb pressure tube using a cold finger attached to steady state thermal diffusion equipment. Ultrasonic velocity ratio method as well as conventional ultrasonic parameters with an immersion technique was developed to detect small hydride blisters on the Zr-2.5Nb pressure tubes.

Jan 1, 2006

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, a group called Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903± hm2 (22,000± acres) on Black Mountain, which contains the state&apos;s highest point, as unsuitable for mining. A fast track legislative process was triggered that could have "taken" 91 Mt (100 million st) of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed

Jan 1, 2002