Search Documents

By Akita Ito, Sumio Kato, Mikio Sugai, Shinichi Nakata

"Spark Plasma Sintering (SPS) is a newly developed method for the sintering of metal and ceramic powders, and completes their densification at low temperature and in short period. The SiC powder was synthesized from diatomite and graphite or carbon black by heating at 1 450°C for 1 hr in an argon atmosphere. The synthesized SiC powder was heated at 1500-1800°C, 50 MPa for 15-18 min by SPS. The relative density of sintered SiC body increased with the rise in the temperature. The oxidation of the surface of the SiC particle and impurities in SiC from diatomite greatly influenced the sintering promotion of SPS.IntroductionThe SiC has high hardness because of the covalent bonding, and is also excellent in thermal and chemical stability. However, it is difficult to obtain a dense SiC sintered body by the combustion heating-method. Therefore, the dense SiC bodies have been made by the use of additives and I or the hot pressing (HP) method.In this study, the SiC powder was synthesized by using diatomite of natural products and graphite, and carbon black of reagent as raw materials, and the relationship between the properties of SiC powders prepared at various synthetic conditions and the density of sintered body by SPS was examined."

Jan 1, 2000

By H. H. Klepfer, M. E. Snyder

UNTIL very recently, the commercial availability of the rare earths as metals has been very limited. Fabrication of mill products from these metals has not been studied in most cases. This note reports the results of the development of fabrication techniques for thulium. Thulium has a melting point of about 1550°C and a hexagonal close-packed crystal structure. It oxidizes in air to give a black oxide (TmzO,). The procedures for producing thin thulium foil were developed on one ingot weighing about 220 g and were subsequently applied in processing about a pound of metal to foil. Several alternates for the various fabrication steps were investigated and will be discussed. The metal fabricated was in the form of commercial chill-cast ingots 1 in. in diam and 2 in. long weighing approximately 220 g. Impurities in the ingots were reported by the vendor to be 4000 ppni tantalum, 2000 ppm calcium, 200 ppm nickel, 100 to 200 ppm iron, 100 ppm europium, and less than 100 ppm copper, lutetium, and ytterbium. In addition to these impurities, several salt-like inclusions as large as l/8 in. in diam were revealed along the center line of the one ingot sectioned. Preliminary tests indicated that small wafers cut from the as-cast ingot would not fabricate readily by rolling. Forging of copper-jacketed wafers was therefore attempted. At 1550"F forging was satisfactory but an apparent reaction of copper with thulium demanded investigation of lower temperatures. Therefore, the remainder of the test ingot was forged at 1450°F—with only minor cracking. All ingots forged were inserted into copper tubes of 1 in. 1D and 0.125-in. wall thickness. The jackets were sealed by flattening the ends of the tubes and welding under helium. Heating time at 1450°F was 30 min. Press forgings of 1/8 in. per pass were used, followed by 10 min reheats. When the ingots had been squared and reduced to 0.250 in. in thickness, the original copper jacket was stripped off and replaced by a new jacket in preparation for hot rolling. Hot rolling at 1450" F without edge cracking was readily accomplished after forging. Excellent results were obtained with 10 pct reductions of thickness followed by 5 to 10 min reheats. After reduction of thickness from 0.250 to 0.100 in. the copper jacket was removed. It was found, in fact, that hot rolling in air was possible. A tenacious black oxide similar to that seen on zirconium was formed during 3 min reheats at 1450°F. Reduction in air to 0.010 in. foil was possible taking 10 pct reductions per pass. The oxide coat formed during hot rolling in air could best be removed by sand blasting and pickling. Common pickling solutions containing polar solvents were found to attack the metal too rapidly and a concentrated nitric-hydrofluoric acid mixture attacked neither the oxide nor the metal. The most satisfactory pickling solution was 52 vol pct concentrated nitric acid-48 vol pct glacial acetic acid. After forging to 0.250 in., vacuum annealing and cold rolling was found to be another satisfactory alternate to hot rolling in copper jackets. After forging. a hardness of Rockwell B76 was found. Annealing in vacuum (2 X l0-5 mm of Hg) for 1 hr at 1200"F did not alter this value. Annealing at 1470"F for 1 hr brought the hardness down to R;]63. With cold rolling (5 pct per pass) the hardness returned to about R,1:76 after 20 pct reduction and edge cracking became noticeable. However, cold rolling to a total of 40 pct reduction in thickness (RI,,83) was possible before edge crack propagation became serious. Good surface finish was obtained, and the metal loss due to oxidation was minimized by cold rolling and vacuum annealing. Using this procedure the yield of 1.25 in. wide by 0.010 in. thick foil from a 1-in. diam ingot was about 40 pct.

Jan 1, 1961

By D. Eyde

The zeolites review arrived too late for the June issue. The natural zeolite industry continues to grow even as some companies look for the exits. Production for 1993 was estimated at between 42 and 44 kt (46,000 and 48,000 st). That is between 7 and 9 kt (7700 and 9900 st) above 1992 production. GSA Resources, Saint Cloud Mining, Steelhead Specialty Minerals, Teague Minerals, UOP and Zeotech all reported continued growth last year. At the same time the East-West Minerals' Eastgate mordenite mine, and American Resources' Ash Meadows clinoptilolite operations both shut down their processing plants and are attempting to sell the mines and facilities. In addition, Tenneco Minerals continued its attempt to sell the Mud Hills clinoptilolite deposit. Unimin entered the natural zeolite industry through its acquisition of several properties of Aimcor. The properties included the Ben-Jel bentonite and Castle Creek clinoptilolite deposits and processing facilities near Caldwell, ID

Jan 1, 1994

By John G. Tate, George W. Nicolson, James L. Bruce

For more than 25 years modern mining has been carried on in the Island of Cyprus, Mediterranean Sea, by the Cyprus Mines Corp. of Los Angeles, Calif. The general features of these operations have been described.' From 1935 to June 30, 1940, top slicing in the Mavrovouni mine produced in excess of 2,000,000 long tons. The rate for the last part of this period was approximately 50,000 tons per month. Description of Ore Bodies The shape Of the Ore body now being top sliced in the Mavrovouni mine is an inclined irregular pyritic pipe or chimney of large dimensions) extending from unknown depths below the bottom level at elevation 250 ft below sea level) to the highest level at elevation 400 ft above sea level. The present surface above the ore body lies between 550 and 650 ft elevation. Undoubtedly the Ore body extended to surface and was Mined by the ancients by opencast and underground methods. The old pits were gradually filled up by erosion until now they show as slight depressions in the topography. The largest area of the Ore body is at elevation 170 ft below sea level, where the horizontal section is almost elliptical, with a width of 600 ft and a length of 1000 ft. Below this elevation the shape of the ore body continues to be elliptical but with reduced dimensions. Above this elevation it rises flatly towards the south with a substantial depression in the upper-side of the chimney and irregular ridges or wings rising on each side. It gradually grows smaller as it rises. The ore body is a pyritic replacement of andesitic extrusives which occur as flows and pillow lavas. With the exception of the upper portions of one or two small offshoots rising from the main ore body, all ore is completely surrounded by andesite. Most of the andesite lying above the ore body is covered by marl and Clay sedimentaries of Miocene and later age, The Miocene is presumed to be older than the ore mineralization. That portion of the andesites which lies between the sedimentaries and the ore body has been broken by slumpage, and weathered, and iron-Stained by the descending meteoric waters, It is a mass of crushed material that caves and follows downward readily as the top-slice stopes retreat. The main ore body is a heavy cupreous pyrites mass assaying on the average about 4.0 pet Cu; 48.0, S; and 42.0, Fe. In places the copper drops below 1.0 pet. on the borders of this heavy sulphide ore body lie disseminated cupreous pyrites ore deposits of large dimensions. some portions of these appear to be closely related to the heavy sulphide ore, as the ratio of copper to pyrite is about the same. The greater part of the disseminated ore, most of which lies immediately to the east of the main Ore body, contains less than 0.10 pct Cu and about 25.0 to 30.0 pct S. 'This probably can

Jan 1, 1949

By R R. J McAllister, K Moffat, S Heyenga

This paper examines the statistical relationship between quality of life indicators and the gross value of mineral production from Australian regions. We used quality of life indicators, aggregated for 673 local government areas, of household income, housing affordability, access to communication services, educational attainment, life expectancy and unemployment. We find no evidence of systematic negative associations between quality of life and the gross value of minerals production. Instead, mining activity has a positive impact on incomes, housing affordability and communication access across regional and remote Australia. Whilst we do not establish causality between mining activity and quality of life, our analysis prompts a rethink of the æresource curseÆ as it applies within a single country. Nevertheless, our findings are tempered by extensive anecdotal and empirical evidence of the negative social impacts of mining on specific demographic sectors, localities, families of fly-in, fly-out mining operations and individuals. This contrast may be a scale issue, with the regional benefits of mineral wealth masking highly-localised inequalities and disadvantage. We suggest that there is a need to better understand these impacts and, more importantly, the types of policy mechanisms government and industry can adopt to mitigate or avoid them.

Jan 1, 2009

By Hugh K. Taylor

"With some justification, people have long complained about the indefinition of ore reserves. Perhaps they were led to expect too much; from former and easier definition practices in the once common underground mines with exposed and available assets, where the obsolete term 'ore in sight' was at least partly literal. But such mines have become rarer, and their underground development less affordable. For most projects, valuations and its definitions have thus been advanced from actual to prospective mines, leaving a very wide gulf between 'what is there' and 'what may happen to it'. This brings the double challenges of reduced geological and technical assurance and the protraction of economic uncertainties.This paper avoids the popular field of regional resources, being confined to what may possibly be mined within single or closely grouped deposits. For these, many estimates of tonnage and grade must be made, defined and declared long before assessment of feasibility; and the uncertainties of the latter make it an unsound base for defining the earlier quantities. Despite the best of intentions, implied or inferred promises may proveimpossible to honour.A simpler framework of definitions is suggested, to some extent reverting to an earlier dependence on supporting work rather than on opinions of economic assurance or future events that are more properly the functions of production and cash flow schedules."

Jan 1, 1994

By Raymond D. Daniels, Frank E. Rizzo, James D. Gerber

ThIS discussion describes a method for the addition of small amounts of oxygen to columbium (niobium) in an accurate and reproducible manner. The method is based on the complete reduction by columbium of a carefully weighed amount of another metal oxide. The equilibrium Pq associated with Cb-CbO mixtures is extremely low, e.g., 10"25 atm at 100O°C, and the pressures over Cb-0 solutions are even lower. The equilibrium Pq associated with a given metal-metal oxide mixture can be easily obtained, with the aid of a Richardson-Jeffes chart.' Although columbium should effectively reduce almost any metal-metal oxide combination, the proper choice of a metal-metal oxide system is complicated by the low rate of oxygen transport in the gas phase at low oxygen pressures and the difficulty in reducing any columbium suboxide formed during the reduction of the oxygen source material. Thermodynamically, oxide formation on columbium will be avoided so long as the oxygen partial pressure over the columbium is below the equilibrium pressure associated with the mixture Cb-CbO. The logical choice of a source for oxygen would appear to be a mixture of Cb-CbO, since oxide formation would be precluded by nucleation difficulty. But calculations using the kinetic theory of gasses indicate that, for a temperature of 900°C, the reaction would proceed too JAMES D. GERBER, formerly Research Assistant, University of Oklahoma, Norman, Okla., is Research Metallurgist, Air Force Weapons Test Laboratory, Kirtland Air Force Base, N. Mex. FRANK E. RIZZO, Junior Member AIME, formerly Assistant Professor of Metallurgy, University of Oklahoma, is Associate Professor of Metallurgy, University of Texas at El Paso, El Paso, Tex. RAYMOND D. DANIELS, Member AIME, Professor of Metallurgical Engineering, University of Oklahoma, is an NSF Fellow, Institute de MBtallurgie Structurale, Universite de euch:tel, Neuchitel, Switzerland. Manuscript submitted October 28, 1968. IMD

Jan 1, 1970

By Gilmore R. Tostengard

The advent of inexpensive computers has opened vast opportunities for improved planning and control of capital projects. The mining and mineral processing industries have welcomed the opportunity, and new and improved quantitative management techniques have abounded. This chapter will discuss commonly used computer applications for economic justification of the project, preparation of the cost estimate, planning the work schedule, monitoring work progress, and control of costs and productivity. Finally, there is a review of the degree to which the industry uses these applications. Our experience suggests that while we in the industry have been quick to adopt the new techniques, the quality of our input data has not always kept pace. During the next decade, our push should be toward improving the quality of the basic data and assumptions so that we can fully benefit from the sophisticated techniques. The GIGO (garbage in, garbage out) principle is a wellworn cliche, but it is especially valid here. One of the keys to getting good input is commitment. Unless the managers who are to use or benefit from the system are committed to it, the effort will fail. They must be com- mitted to the underlying principles of planning and control sufficiently to expend their time and resources on them; planning should be especially given emphasis. They can't be too busy to plan.

Jan 1, 1979

By K. J. Liles

This Bureau of Mines paper describes the composition and properties of drilling fluids for use in high-temperature geothermal wells, and summarizes the problems encountered with fluid use at the known major geothermal sites throughout the world. These include the western continental United States, Hawaii, Italy, Iceland, Japan, New Zealand, and Turkey. Water-base drilling fluids of 9- to 10-lb/gal weights are relied on primarily for geothermal well use, although air drilling is sometimes used. Bentonite-lignite-water systems have been used most often, and additives such as polyacrylates, lignosulfonates, and chromates are employed to improve the properties of the basic system.

Jan 1, 1976

By W. F. A. T. Meihack

The scope of this paper is confined to gas-fluidized beds in pyrometalurgical applications. After considering the general characteristics of these fluidized beds, the author deals with their potential applications, using the following processes, which are currently under investigation, as examples: pretreatment of chromite, prereduction of manganese-ore and iron-ore fines, roasting and prereduction of ilmenite, and roasting and pyrolysis of gold-bearing pyrite. He concludes that fluidized beds are potentially of great benefit to the metallurgical industry, although much developmental work remains to be done.

Jan 1, 1986

By John A. Mavrogenes

The Texaco gasification system developed at the Monte Bello pilot plant efficiently bums petroleum-coke thereby producing syn-gas and electricity. This system produces more electricity than conventional burners, yet the only by-products are pharmaceutical grade sulfur and V -rich slag. Vanadium is known to exist in multiple valence states in compounds which possess a wide range of melting points and physical properties. Consequently, it becomes important to carefully regulate oxygen fugacity throughout the system in order to control vanadium valence state. Vanadium phase equilibria is presently poorly understood, in large part because of the multiple oxidation states of vanadium (-I, 0, +2, +3, +4, and +5) and the difficulty of unequivocally identifying the valence state(s) in many compounds. The operation of these gasifiers at approximately 1400°C is well above the melting point of V20S but considerably below the melting temperature of V02 and V 203. If J02 can be regulated to keep the burner within the V 205 field, slag material would more likely remain molten and more easily flow out of the bottom of the burner. In pure V oxides. the oxidation state is readily determined by microprobe analysis. where V20S (V+5) is 56% V, V02 (V+4) is 61.4% V, and V203 (V+3) is 68% V. However, V valence in multi-element phases (especially phases containing other elements of variable valence) cannot be resolved by microprobe analysis alone. Petroleum-coke gasification slags collected from within the gasifier under different oxidation conditions were studied by electron microprobe analysis (EMPA). X-ray diffraction (XRD). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. Raman spectrometry in conjunction with microprobe analysis was found to resolve the valence of vanadium in the phases of these slags. Raman spectra collected from homogeneous single phase V-oxide standards in vacuum at low temperatures (-150°C) yielded peaks characteristic to each valence state. Gasifier slag samples are, however, much more complicated. Oxidized samples contain: fine grained (Ca. Mg, Fe. V) oxide matrix of variable composition, (Fe. V, Ni) spinel. (Fe, AI, V, Ni, Mg) spinel, V205laths, AI-Si glass blebs and Ni sulfides. Reduced samples contain: crystalline Ca-siIicate matrix, subhedral to euhedral (V, Fe, Mg, AI) spinel, subhedral V02, Fe and Fe-Ni sulfides, Fe-Ni alloys, and complex Ca-oxide matrix. The different spinel assemblages, the characteristic V-oxides and the distinctly different character of the matrices makes the oxidized and reduced slags readily discernible.

Jan 1, 1995

By E. Maxwell, C. J. Bechtoldt, H. C. Vacher

IN the course of an investigation of the properties of metals at low temperature there was occasion to determine the constitution of four iridium-osmium alloys. There is very little information in the literature1 on the constitution of synthetic Ir-0s alloys. Zvyagintzev' s has made a comprehensive study of different natural Ir-0s alloys and concludes that alloys containing more than 32 pct 0s have the close-packed hexagonal structure of osmium, whereas those containing less than 32 pct 0s have the face-centered cubic structure of iridium. The alloys studied in this work were prepared by the American Platinum Works, Newark, N. J., and were received in the form of fragments approximately 1.5 mm average diameter. The fragments had been obtained by crushing ingots made by fusing charges of iridium and osmium under an arc and air cooling. The ingots were not given a homogenizing heat treatment. Sample fragments Table I. Results of X-Roy Diffraction and Microscopic Examinations Phases Present as Determined by X-ray Diffraction Osmium Alloy Close- Iridium Face- Packed Centered Osmium, Iridium, Hexagonal Cubic Mlcro- WtPot Wt Pct Structure Structure scope 0 99.9 None Present 1 23.6 76.4 None Present 1 38.7 61.3 Present Present 2 59.4 40.6 Present Present 2 79.0 21.0 Present Not detected 2 99.9 0 Present None 1 Note: Chemical analyses of the iridium, osmium, and alloys were furnished by the American Platinum Works. of the iridium and osmium used in making the alloys also were included. Several fragments of each metal and alloy were examined microscopically and by X-ray diffraction. For the X-ray method the fragments were crushed further to pass a 270-mesh screen, then sealed in evacuated fused-silica tubes, heated to 1100°C for 18 hr, and allowed to cool in the furnace. Powder X-ray diffraction patterns were obtained from the annealed fragments by means of a Norelco camera having a diameter of 114 mm, and unfiltered cobaIt radiation. For the microscopic examination several fragments in the as-received condition were mounted in Melmac, (American Cyanamid Co.) and ground using the conventional series of abrasive papers. The polishing was done with 0-2 diamond abrasive on a Microcloth (Buehler Ltd.) lap, wet with xylene. After polishing, the surface was etched electrolytically in a 10 pct solution of chromic acid or in a 10 pct solution of potassium cyanide. Both reagents attacked the osmium-rich constituent, whereas the iridium constituent was attacked slightly by the chromic acid reagent and not noticeably by the potassium cyanide reagent. The results of the X-ray diffraction and microscopic examinations are summarized in Table I. Fig. 1 shows the microstructure of a 21 pct Ir-79 pct 0s alloy. The results indicate an appreciable solid-solu-bility range of osmium in iridium as was reported by Zvyagintzev.' The solid-solubility range of iridium in osmium is more restricted, apparently less than 21 pct Ir. This implies a large range of composition in which two phases can coexist that was not reported by Zvyagintzev.

Jan 1, 1955

By Z. H. Liu

We experimented with slurry which from one of coal preparation plant in Guizhou province and made researches on double hump gradation, one of critical factor of gradation technology, which can influence pulping character in the process of making coal water mixture (CWM). The purpose for it is to find the best particle gradation which can meet the requirements in concentration, viscosity, and stability for CWM. The final result is that the concentration, viscosity, stability of CWM can meet the requirement for industrial use while the rate of fine particle in the slurry is 70%~75% and the maximum concentration of 62%.

Jan 1, 2014

By S. Klingmann

ABSTRACT In this paper, we used data collected from the Gibraltar mine to analyze the effect of the TyreSense tire monitoring system on tire performance by reducing tire wear and preventing premature tire failure or damage. We analyzed the relationship between tire temperature, tire pressure, and tire failure or damage to help better understand the importance of controlling high tire temperature and pressure. The results enhance and expand the knowledge of the management of tire operational pressure and temperature.

Jan 1, 2014

Jan 1, 1949

By Deicy Sánchez

"Las estrategias más frecuentes para la remediación de suelos contaminados por actividades mineras son: el uso de coberturas sintéticas o naturales para aislar contaminantes ($ 0,5 millones / acre) o la revegetación directa (menos costosa pero difícil de sostener) ($ 5000 / acre). En busca de métodos más efectivos y menos costosos, realizamos una serie de estudios para determinar que combinaciones de enmiendas y bacterias podrían dar mejores resultados en el crecimiento de vegetación y disminución de drenaje ácido de mina en relaves mineros con alto contenido de arsénico."

Sep 1, 2017

By S. H. Advani, J. K. Lee, K. S. Chan, J. M. Avasthi

A summary of field equations governing the hygro-thermo-mechanical (coupled temperature, moisture, and stress) response of geological media is presented. The applicability of these equations, with appropriate boundary conditions, to the study of basic mechanisms associated with underground coal gasification (UCG) process is discussed. In particular, the phenomenon of stress-induced spalling resulting from intense drying near the gasified cavity and in situ effects is investigated by means of the finite element method. Some typical results from sample finite element model representations are presented for the evaluation of field experiments.

Jan 1, 1986

By A. W. Fahrenwald

The purpose of screening is to separate a crushed or natural product into one or more products in which size of grain is constant, or within certain size limits. The ore dresser finds need for this operation in the laboratory, in the study of ore-dressing processes, and for various purposes in the plants. In the plant, for example, screens are employed in closed circuit with crushing devices such as rolls, and sometimes are used in closed circuit with ball mills. Screens are generally used to prepare jig feed where a sized feed is wanted. For any given sieve opening there is in any feed a certain percentage of grains that will pass through the sieve meshes only with difficulty and under favorable conditions. For example, cylindrical grains of length greater than the maximum dimension of the sieve mesh and of diameter less than the sieve opening pass the sieve only when the long axis of the grain is normal or nearly normal to the sieve. Whether such grains should actually be in the through's or the oversize of a screening operation--considered from the point of view of the subsequent treatment of the grains--can not be said. The grains that pass the sieve opening in a screening process only under-favorable conditions have been named "difficult" grains by R. K. Warner.4 In many ore-dressing flow-sheets it probably matters little whether these difficult grains show up in the screen through's or oversize. The main objection to them is that they are sieve-blinding.

Jan 1, 1929

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By R. Shiva Kumar, G. Sreedhar, S. Sharma

Some of the Indian origin iron ore deposits located in Bellary, Karnataka province are having peculiar characteristics of Iron ore deposits (Hematite) having Iron above 64% and 30-40% lump (-30+6mm) recovery which are not suitable to use in blast furnace due to not meeting the specification of Tumbler Index and Abrasion Index. In general for high grade Iron ores, process flow sheet involves crushing and screening (dry/wet). In the contest of high grade Iron ores located at Bellary sector of Karnataka state in India, lump generated from this process could not attain the required physical properties (Tumbler Index, Abrasion Index) and metallurgical properties , even though the grade of the lump ore is above 64% Fe. Washing techniques like Drum scrubber and Log washer play major role in improving the metallurgical properties of Iron ore lumps by removing the light and hard layers of clay, silica coated over the lumps. In this study the effects were compared of drum scrubbing and log washing on iron ore lumps. It is found that by incorporating simple washing technique i.e. drum scrubbing or log washing, Tumbler Index of Iron ore Lumps could be increased from 74% to 78% which is acceptable for use in Blast furnace. From the Drum scrubber and Log washer tests, it is clear that Log washers have an edge over Drum scrubber in removing hard coated clay on surface of Lumps. This simple washing technique facilitate us to utilize the lumps directly in blast furnace and eliminate the unnecessary crushing and grinding of the ore so as to meet the specifications of Sinter fines and pellet feed.

Jan 1, 2014