Search Documents

By T. C. Cheng, G. P. Demopoulos

It is the object of this paper to discuss various options for improving the hematite process in terms of increased throughput hence lower capital cost and production of saleable quality hematite. With reference to increasing the throughput of the process, it has now been determined via the analysis of Akita Zinc Co's continuous industrial autoclave performance data that the process kinetics is limited by the rate of the hydrolytic precipitation reaction. By correlating the hydrolytic precipitation rate to supersaturation ratio, it is shown that accelerated kinetics can be achieved via the following measures: (1) in-situ neutralization with addition of zinc calcine; (2) elevation of temperature; and (3) dilution of feed; of which, the first one was retained for further evaluation. According to presented estimates, addition of calcine, amounting to only 2.6% of the total zinc calcine processed, can allow for shortening the retention time by at least 50%. Such drastic shortening of retention time may be either used to increase the throughput of a given autoclave circuit or alternatively to release autoclave capacity for clean hematite production. Hydrothermal treatment of the crude hematite product proved effective in producing clean hematite as according to laboratory tests, hence allowing the sulphur content of hematite to be reduced from around 4% to less than 1%. A conceptual flowsheet incorporating in-situ neutralization for accelerated kinetics with hydrothermal upgrading of crude hematite without sacrificing production capacity and with minimum upset of the plant's water balance is described.

Jan 1, 2004

By Hernán Parra

Las pruebas cerradas de flotación (ICFT) son necesarias para el diseño de plantas a niveles de prefactibilidad y factibilidad, ya sea en proyectos greenfield o brownfield. Estas pruebas se realizan después de haber hecho un estudio previo de flotación batch y se usan para simular un circuito continuo. En este trabajo se reseñan los estudios sobre el tema, se busca establecer la manera adecuada de ejecutar la práctica de laboratorio y de evaluar los resultados experimentales, con el propósito de introducir mejoras en el diseño de plantas.

Aug 30, 2017

By M. Fig, B. Treffner, J. Brune, C. Strebinger, G. Bogin, D. Pardonner

"Methane gas explosions in a longwall coal mine can originate from in or around the gob and can seriously harm nearby workers and equipment. In order to fully understand the explosion flame and pressure wave propagation in the mine, it is important to investigate methane flame propagation in confined spaces as well as flame interaction with rock rubble and other mine structures. The latter can lead to enhanced turbulence causing high-speed deflagrations and/or detonations. Researchers ignited methane-air mixtures in horizontal, cylindrical reactors that contained inserts to simulate various gob characteristics. Rock surface topology and ignition location were investigated. Results show rock surface roughness increased fluid motion, thereby increasing methane flame front propagation velocity, overall pressure rise of the explosion, and time of pressure decay. Moving the point of ignition away from the open end of the reactor resulted in an increase in peak overpressure and an overall pressure rise of the explosion. Experiments were used to validate a computational fluid dynamics (CFD) combustion model that will be incorporated into a mine-scale explosion model to simulate and predict explosion hazards of large scale methane gas deflagrations in longwall coal mines. INTRODUCTION Coal mining is an integral part to our global society with coal-fired power plants providing about 40% of our global electricity [1]. A common method of extracting coal underground is by longwall mining. Researchers and investigative reports have found that explosive gas zones of methane-air mixtures can form along the longwall face and within the longwall gob, presenting an explosion risk to nearby workers and equipment [2]. In an explosion, the resulting flame and pressure wave presents a fatal traumatic injury hazard and can cause serious damage to equipment. In order to evaluate and mitigate the explosion risks in longwall coal mining, researchers at the Colorado School of Mines are developing a coupled CFD and combustion model of a longwall coal mine. The purpose of the model will be to better predict the explosion hazards under various mine conditions in order to build stronger prevention and mitigation strategies for miners."

Jan 1, 2018

By I. Geldmacher

In-Seam Seismic (ISS) methods have been used extensively worldwide for the past 10 years to assist mine planning, espe¬cially longwall mining in coal seams. The technique is only starting to gain wide acceptance in North America where it is being applied in a much wider variety of applications than was initially considered. Surveys elsewhere have concentrated on the detection of faults (structures) in coal mines prior to longwall mining. The majority of surveys in North America has been the location of abandoned workings which were not adequately surveyed prior to closure. Modeling data based upon the lithological logs, geophysical logs and interpreted sections show whether the method will be successful prior to carrying out the survey. The surveys have been performed to locate abandoned wor¬kings from the surface and underground using both seismic reflection and transmission techniques. Data from coal seams in both Illinois and West Virginia will be presented. A second method where ISS surveys are being applied to detect old workings will be presented. The ISS tomography produces an image of the P-wave and Channel Wave velocities which is representative of the material through which the signal traveled thus identifying the location of the old workings. Data from Texas will serve as an example.

Jan 1, 1990

By Caibin Wu, Ali Lei, Ningning Liao, Jingsheng Ye

"The particle size distribution characteristics of ground product can influence the quality of the classification overflow and the next beneficiation indexes in an ore concentrator. Usually, the size distribution of ground product is considered to be determined by that of new ball mill feed. However, based on large amounts of data from industrial grinding circuit surveys, this paper has clearly shown that the size distribution of ground product should be determined by the size characteristics from classification underflow unless the circulating load was small, because the new feed is an important component and occupy a dominant position of mixed ore from belt feed and classification underflow. On the other hand, the correlation coefficient of the size distribution between ground product and classification underflow can be more than 0.99 when the relevance principle and its method are used. Meanwhile, their P80 value also keeps a synchronous correlation. The greater the capacity of classification underflow is, the higher the correlation of size distribution between the ground product and the mixed feed is. Furthermore, the correlation coefficient of the size distribution between ground product and classification overflow which is from primary or secondary can be 0.96. It is another discovery that the correlation coefficient is related to the type of classifier. The coefficient of size distribution of overflow and underflow from hydrocyclone is superior to that of spiral classifier, which can explain the reason why the hydrocyclone is widely used to replace the spiral classifier in concentrator.INTRODUCTION It is well knows that ball mill circuits closed with cyclones or spiral classifier such as a primary grinding circuit, a secondary grinding circuit and SAB mill have become an industry standard. Which grinding process employed will be determined by the P80 value of ground products. When the primary closed circuit ball mill or SAB that it is different throughout between the two processes was employed, a grinding fineness with -200mesh under 68% will be available. However, the secondary grinding circuit with the fineness of -200mesh above 80% can be conducted. Of course, the grinding fineness is determined by the grain size characteristics of the mineral."

Jan 1, 2018

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987

By A. W. Lovett

"THE last two years have been years of recession or, perhaps, years of marking time, depending upon whether the observer is a pessimist or an optimist. There has been a slackening in the industrial tempo that has been reflected in many ways in the national economy. As one of the chief barometers of economic health, the consumption and supply of energy reflect this slowing up.These same two years have also seen significant changes in the relation between the sources of energy. In periods of declining demand, it has happened in the past that coal, as the basic or residual source of energy, has shown the effects to a greater extent than the other energies. In these two years, however, in addition to this usual effect, there has been the acceleration in the Joss of market to diesels in the railway consumption category and the continuing decline in domestic consumption. The story of these years is presented in the statistical tables that form the foundation of this paper. Statistics, particularly in the form of tables, are rather dry and are sometimes difficult to follow but the overall developments are illustrated by graphs which present a more striking picture."

Jan 1, 1959

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By Naj Aziz

n Australia, the common method of laboratory testing of bolt for load transfer capacity determination is by short encapsulation push testing. Some concerns are raised about the validity of the test methodology, as the method does not reflect on the actual load transfer characteristics of bolt in real field situation. Thus, laboratory testes were carried out to examine the load transfer mechanisms of bolts in both the push and pull conditions. Tests were conducted by shearing a short resin encapsulated bolt out of a cylindrical steel sleeve. Three types of bolts with different surface profile configurations were tested. The study was complemented with numerical simulation of the test methods. Irrespective of bolt type the average shear load and shear stress values were found to be greater in push test, and the displacement at peak shear load was greater in pull test. The average shear stifhess values were greater in push test. The numerical simulation of the bolts provided a clear understanding of the stresses and strains generated by different bolt profiles during both the pull and pull testing process, thus allowing a better appreciation of the load transfer mechanism process.

Jan 1, 2005

By Verne S. Mutton, William A. Slivensky, Eric S. Weiss, Kenneth L. Cashdollar, Deepak R. Kohli

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, cooperated with Tecrete Industries Pty. Ltd. and BHP Australia Coal in a research program to evaluate the strength characteristics and air leakage of four seal and two stopping designs for use in underground coal mines. A fundamental safety research area for NIOSH is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach to achieve this goal is to develop new and innovative seal designs that provide increased explosion isolation protection for the mining personnel against ignitions that originate from within the gob or. other worked-out areas of the mine Full-scale seals and stoppings were constructed in the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. They were ail--leakage tested, then subjected to a series of explosions with average pressure pulses ranging from 25 to 500 kPa (3.5 to 72 psi). Instrumentation measured seal displacement and acceleration as a function of time, providing data to assist in the development of numerical models 1'01- future seal design. All three seals designed with Meshblock wire forlnwo~-k ant1 a lnonolithic shotcrete core withstood the first explosion test, which generated an avcr-age rnaximu~n pressure of - 140 kPa (-20 psi) while maintaining acceptable air leakage rates. These seals I-anged from 175 to 325 mm thick. They included a 2.7-m-high by 325-mm-thick seal that was tesled 27 hr after completion against this - 140-kPa explosion pressure, a special requirement of the test program. This seal survived explosions with pressure pulses up to 300 kPa (43 psi). The 2.3-m-high by 325-mm-thick Meshblock seal survived three explosion tests with overpressures up to 455 kPa (66 psi) and satisfied the air leakage criteria. A I ,200-mm-thick plug seal was constructed of two Gunmesh formwork walls in-filled with shotcrete and a 3,450-kPa (500-psi) strength Aquablend core. This plug seal survived three explosions with pressure pulses ranging 11-om 150 lo 430 kPa (-22 to 62.5 psi) with no measurable postexplosion air leakage. Two Gunmesh stoppings with thicknesses 01' 40 and 75 inln withstood explosion overpressures of 23 and 115 kPa, respectively. Anchoring all seal and stopping designs into the roof, ribs, and floor with steel "rootbolts" provided very effective boundary constraint that is critical to the performanceofstructures subject to explosion overpressures.

Jan 8, 1999

Segregation studies in ternary systems of glass ballotini, iron ore and coke particles (with size range of 1-8 mm in each) in filling and emptying a laboratory size Paul Wurth hopper are described. In-bin segregation is shown to be a function of the position in the hopper, the nature of the material and the feed composition. The in-bin results are correlated by the equation C = C0k, where C and C0 are the size compositions (wt per cent) in the hopper and feed respectively, and k is an experimentally obtained segregation constant. The results of now pallern measurements show that material discharges from the hopper according to the sequence; core now - wall now - scaffold now, where the latter represents stagnant material at the hopper wall that discharges last. Size segregation in the discharge stream from the hopper is shown to be a function of in-bin segregation and hopper now pallern. A method of predicting discharge segregation from these two sets of data is suggested. The results of the model studies are also compared with industrial data and these show satisfactory agreement. Discussion of the hitherto ignored effect of size segregation on hopper now rates, stoppages and other operating problems is also included.

Jan 1, 1985

By E. Gybbon Spilsbury

In a paper* read at the last meeting of the Institute, in Scranton, Pa., I referred to the proposed introduction at the Haile gold-mine, South Carolina, of a novel method of chlorination. I have since

Jan 1, 1888

By G. Stephan Derrickson

Any type of agitation within a confined vessel is primarily concerned with two parameters: 1) A level of agitation describing the homogeneity of the constituents (whether it be suspension or mixing) and, 2) the energy efficiency with which this level of agitation is accomplished. The following is an attempt to present a solution to the problem of adequately defining and optimizing these properties. First included is a discussion of the application of good design practices to the determination of a mechanically efficient shape to the blade elements of the propeller. These practices, excluding several appropriate modifications, have been known, but not well understood, in aircraft fluid mechanics for a number of years. Secondly, having optimized the direct impartation of energy to the medium being agitated, attention is turned to one of the more perplexing phenomena of multi-phase systems - definition and prediction of agitation levels. The result of recent study and testing is a method of scaling which the authors feel provides a lucid understanding of governing physical parameters within the agitator itself, allowing one to scale up and down with confidence.

Jan 1, 1982

By Victor F. Paterno

In December of 2007, a joint venture of J.F Shea, Skanska and Schiavone referred to as S-3II, was awarded a $1.15 billion (? 886,880,000) contract to construct the run-ning tunnels and station structures for the Number 7 Line Extension Project in New York City by the Metropolitan Transportation Authority Capital Construction (MTACC) and New York City Transit (NYCT). As part of the contract, a technically complex and critical connection of the new tunnel to the existing, operational 7 Line subway was required. This paper describes the innovative design approach that was conceived to carry out the underpinning and excavation works both within the east-west 7 Line subway tunnel and beneath the north-south, 4 track, 2 level Times Square Station for the A, C & E trains. This underpinning provided temporary support to the subway substructure as the grade of the tunnel invert was lowered up to 10 feet (3 meters) into the rock sub-grade to allow the future subway to pass under the basement of the world?s busiest bus terminal. In addition, the creation of a new portal connecting the existing subway tunnel and the subterranean level of the Port Authority Bus Terminal by means of underpinning structural footings and horizontal spiling/poling of existing ground will be discussed.

By R. Ghisleni, R. E. G. Bohrer, L. Radtke, R. M. C. Santana

"The major source of environmental pollution in urban areas is the transport sector and its impact on human health and the greenhouse is preoccupying. In many works of literature is monitored the pollutants in urban cities, however in specific areas such as universities, they are scarce. Therefore, the aim of this work is to monitorate the gaseous pollutans in a bus terminal at Santa Cruz do Sul University-UNISC and to develop a control framework of the air quality. Six points were selected for monitoring, being one of them inside a bus. The monitoring of CO, HC and CO2 were carried out on arrival and departure of the bus. Preliminary results conducted in a day of spring showed that the most critical condition was during the night shift, where the concentration of CO (200 ppm) was the highest, caused by the vehicles increase, due to the larger number of students.IntroductionThe first major global assessment of climate change science in six years has concluded that changes in the atmosphere, the oceans and glaciers and ice caps show unequivocally that the world is warming. The report released on February 2, 2007, the first of four volumes to be released this year by the IPCC, also confirms that the marked increase in atmospheric concentrations of greenhouse gases is the result of human activities.The transport sector has become by far major source of environmental pollution in urban areas. The continual traffic growth has raised concerns over the impact of traffic emissions on human health and urban environmental quality, and has fuelled the demand for a coherent regulatory framework for the management of traffic, air quality and emission at urban level, as well as at regional and national scales.In Greater Metropolitan São Paulo, Brazil, fossil fuel combustion in the transportation system is a major cause of outdoor air pollution (Miraglia&El Kouri, 2007). In China several studies on gaseous emissions are being conducted by F. Costabile&Alegrini, (2007), developed a study on the pollutants in the city of Beijing suggesting methods for the control of pollution.The results obtained from the estimation of the atmospheric pollutants emitted monthly in Campo Grande/MS, Brazil, by buses and minibuses, which employ diesel, biodiesel or natural gas as fuels showed that the substitution of diesel by biodiesel would diminish the emissions of pollutants (Kozerski&Hess, 2006)."

Jan 1, 2008

By S. R. Amos, N. O. Lotter, A. L. Hannaford, J. F. Oliveira, D. W. Broughton

"Ivanplats Ltd appointed Xstrata Process Support to perform the flowsheeting development work for their hypogene and supergene geomet units of the Kamoa Copper deposit, located in the Democratic Republic of the Congo. Through systematic flowsheet development using modern Process Mineralogy, the optimised milestone flowsheet delivered a saleable concentrate grade of 32.8% Cu at 85.4% recovery with hypogene ore, and a saleable concentrate grade of 45.1% Cu at a recovery of 83.4% for supergene ore. The significant value of this development is that a single flowsheet will treat both hypogene and supergene ores and produce saleable concentrates. Further work to advance the flowsheet performance has been identified for investigation in the near future.INTRODUCTIONLocation and Description of the Kamoa DepositThe Kamoa copper resource is located some 40 km west of the city of Kolwezi, in the south west of the Katanga Province of the Democratic Republic of the Congo, in the region of Central Africa. Drilling at Kamoa in 2008-2009 had discovered laterally continuous, sediment-hosted, high-grade stratiform copper mineralisation in a newly discovered copper district that forms a previously unrecognised western extension of the famous Central African Copperbelt – which hosts such world-class deposits as Kolwezi, Tenke-Fungurume, Konkola and Nchanga. This discovery showed that the western end of the Copperbelt in the Congo does not terminate at Kolwezi (Friedland & Broughton, 2009). The resource contains hypogene and supergene geomet units with a transitional zone located inbetween the (upper) supergene and the (lower) hypogene. In the hypogene unit, the major copper sulphides are bornite, chalcopyrite and chalcocite, whilst in the supergene, the sequence is led by chalcocite, then bornite, and finally chalcopyrite. Covellite is present in both units as a minor copper sulphide. Both geomet units will be mined and treated in one concentrator, either as blends or as campaigns."

Jan 1, 2013

By T. G. P. Vasquez

The elimination of metal ions from aqueous solutions by biosorption plays an important role in water pollution control. Heavy metals are hazardous to the aquatic ecosystem and pose possible human health risk. Beside the toxic and harmful effects to organisms living in water heavy metals also accumulate throughout the food chain and may affect human beings. Conventional methods for removing metals from aqueous solutions before they are disposed of include chemical precipitation and sludge separation, chemical oxidation or reduction, ion exchange, reverse osmosis, electrochemical treatment, and evaporation. Alternative processing methods are being considered more seriously. Sorption and/or complexation of dissolved metals species based on the chemical activity of biomass, known as biosorption, is the base of the new technology for metal removal and recovery. Different types of biomass (dead and alive) have been investigated for biosorption of heavy metals ions. In the present work, the cadmium biosorption capacity and bioflotation of Rhodococcus opacus were studied. The adsorption capacity of biomass was investigated by batch experiments, the influences of some variables like pH and ion concentration were evaluated and the experimental data obtained for each metal were evaluated and fitted using adsorption and kinetic models. The bioflotation process showed that R. opacus has excellent features as collector and foaming agent after metal biosorption. Around 90% of cadmium uptake by the biomass was achieved by bioflotation.

Jan 1, 2006

By Bernhard J. Ralph

In refractory gold ores much of the gold occurs in sub-microscopic form in sulfide minerals, most commonly pyrite and arsenopyrite Bacterial leaching is being developed as a pretreatment for these minerals to aid the liberation of gold and a variety of extracting reagents. This paper reviews the nature of the principal micro-organisms involved, the effects of various physico-chemical factors on the rate and extent of extraction, and likely mechanisms involved.

Jan 1, 1989

By Carlos España Ch

El presente texto plantea la mecanización en la mediana minería como método de trabajo para el tratamiento de minerales y trabajos auxiliares. La ejecución de esta mecanización es de acuerdo al tipo de yacimientos de cada caso particular. En este sentido, la compañía minera Alianza S.A. es un ejemplo de este enfoque empresarial, así como las minas Hércules y Coturcán, las cuales implementaron la minería sin rieles, donde el desarrollo y preparación de las vetas se realiza por medio de rampas que puedan tener pilares de 200 mt.s de largo, posibilitando el uso del método de explotación mecanizado-fronton pilar e incrementando la productividad en comparación con las etapas de mecanización incipiente.

Oct 14, 1980

By R Vleggaar

In addressing a short-term operational need for the relocation of a tailings storage facility reclaim pond, a mine has achieved a host of water management objectives. Through effective planning and adoption of a strategic æwhole of mine lifeÆ approach, the mine has achieved significant environmental, social and economic benefits. A review of all water management aspects across the site identified a host of other interrelated water issues and concerns which, if dealt with individually, would prove too costly for individual operational departments. When considered as a whole, however, the issues became opportunities and provided the stimulus for integration of the site water management system. The development of site water and solute balance models provided the tool by which a number of water management options/strategies could be evaluated. The conceptual design and costing of the proposed water infrastructure further facilitated the evaluation of the multiple benefits to be gained from each option. A business case could then be made to mine management for the preferred option. The recommended water management strategy finally recommended to the mine not only provided a tailings storage facility (TSF) reclaim pond, but also provided for:increased wastewater recovery from the TSF, the capture of all waste rock dump run-off, additional water harvesting from local creeks, increased wastewater reuse, improved environmental water management, infrastructure that could be used by the local community after mine closure, and overall cost savings. This paper illustrates how effective water management planning can provide both short-term economic and environmental benefits, as well as long-term social benefits.

Jan 1, 2006