Search Documents

By J. K. Wen

The Mojiang nickel deposit is situated in Mojiang county, yunnan province, a tropical area in the southwestern China. The known geological resource (measured and inferred) includes 4 million tons of nickel sulphide ore at an average grade of 0.50% Ni and 0.34% As. Nickel minerals are mainly gersdorffite (NiAsS), millerite(NiS), morenosite (NiSO4?7H2O), and more than 50% nickel minerals is gersdorffite which contains arsenic. Pyrite is the dominant sulfide mineral, 22% in the ore and part of nickel minerals are locked in pyrite. It is difficult to attain the nickel concentrate quality allowed by a smelter and the acceptable nickel recovery through flotation due to the high arsenic in the ore and the nickel minerals locked in pyrite. The shake flask tests and column tests for nickel recovery from the Mojiang nickel sulfide ore had been finished by the end of 2003. The column bioleaching tests were carried out using the columns with diameter of 120 mm and height of 1200 mm, and 70% of nickel dissolution was attained in 300 days. A 10,000t pilot test heap was built in the Mojiang Nickel Mine by June 2003. The ore used in the test heap was supplied from the underground mine and was crushed to -20 mm before being feeding to the test heap, which is 4~5 m high, 30 m wide and 50 m long. The naturally adapted mesophile and moderate thermophile have been inoculated into the leaching pile by June 2003. The operating temperature in the heap ranges from 38? to 55?, varying with season. 30% of nickel dissolution was achieved in 3 months and the typical pregnant leach so-lution (PLS) contains 2~3 g/L Ni and 20~30 g/L Fe. The Ni sulfide which was produced by us-ing Na2S 10 t/t?Ni contains 16%~20% Ni and Ni recovery was 98%. 70% of Ni dissolution is expected in 12 months. The test heap was scaled up to 60,000 t of ore per year by mid of 2005. In this paper metallurgical studies and performance of the pilot test heap will be described. The results of mineralogy, shake flask tests and column tests on bioleaching of the nickel sulfide ore are reviewed. The key test heap operation parameters, the performance of bio-heap leahing-Na2S precipitation, ferrous oxidation-ferric precipitation-Na2CO3 precipitation, bacteria in the pile, water and acid balance, effluent disposal, capital and operation costs are also discussed.

Jan 1, 2014

By N Nosaka

Sinter plants currently have to use many types of ores with different properties due to the great demand for iron ores, which was driven by the massive growth in Chinese iron and steel industry. On the other hand, the development of iron ore mines is limited and the quality of iron ores is in a tendency of deterioration. Therefore, the quick evaluation of iron ores has become more important for a stable sintering operation. In addition to such a background, the CO2 gas emission should be decreased from sinter plants according to the Kyoto Protocol on reduction in greenhouse gases. The present paper first describes the methods for testing the metallurgical properties of iron ores, which use a small volume of sample mainly focusing on magnetite ore that is effective for reducing CO2 and NOx emissions from sinter plants. The sintering properties of ores are evaluated separately according to each stage in sintering process, that is: heating stage before melt formation, primary melt formation in adhering fines layer of pseudo-particles, and assimilation of nucleus ore particle with calcium-ferrite system melts.Next, the application of the tests to the blending ores is introduced showing examples of the studies on the effective usage of the magnetite ores with Marra Mamba type ores.

Jan 1, 2005

By P. Bissert, L. Yan, D. Yantek

"Federal regulations require refuge alternatives (RAs) in underground coal mines to sustain life for 96 hours while maintaining an apparent temperature (AT) below 35°C (95°F). NIOSH research has shown that heat and humidity buildup is a major concern with RAs because they have a limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding an RA is very complex and is not easily defined analytically nor experimentally. To investigate heat and humidity buildup in RAs, NIOSH conducted multiple in-mine 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA. The test results show that when moisture was introduced into the tests to represent perspiration and respiration from miners (wet tests), the average measured internal air temperature at midheight increased by 7.7°C, 9.4°C, and 10.5°C, and the RH approached 95%, 94%, and 88%, respectively. For the dry tests when no moisture was introduced, the average internal temperature increased by 8.4°C, 10.3°C, and 12.6°C, respectively. INTRODUCTION If an accident occurs in an underground coal mine, miners who cannot escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the thermal environment inside the RA. The metabolic heat of the occupants and the heat released by the CO2 scrubbing system will cause the interior air temperature to increase. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The internal thermal conditions can subject miners to heat stress, which can lead to heat exhaustion, heat stroke, or even death depending on duration and magnitude of exposure. MSHA regulations require that RAs must be designed to ensure that the internal apparent temperature does not exceed 35°C (95°F) when the RA is fully occupied [1]. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Before a mobile RA can be deployed at an underground mine for emergency usage, it must be tested to show that its internal AT when fully occupied will not exceed the 35°C (95°F) limit. For practical reasons, RA manufacturers usually conduct their tests at above-ground test facilities. To investigate RA thermal response in an in-mine environment, NIOSH conducted multiple 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA in its underground coal mine facility. The work described in this paper could be used by RA manufacturers to determine a final temperature rise based solely on dry and time-reduced testing."

Jan 1, 2017

By Rashmi Kumar, Amit Chatterjee, Sanjay Chandra

The practice of adding alloying materials to a molten bath is an integral feature of many pyrometallurgical operations. However, very little is known about the dissolution rate and solution mechanisms of solid additives in liquid melts. In foundries where large tonnages of liquid metals are handled, there is considerable interest in achieving optimum metal quality at minimum cost. This objective is influenced by several factors and the solution is often plant specific. Though the amount, sequence and mode of ferroalloy addition vary from plant to plant, various fundamental factors determine how quickly these additions dissolve in the bath. At the Ingot Mould Foundry (IMF) in TATA STEEL blast furnace hot metal is used to cast ingot moulds. The composition of hot metal desired for making ingot moulds demands addition of 20 kg each of Ferromanganese and Ferrosilicon in the 12 T transfer ladles into which the blast furnace metal is poured at the IMF. Owing to low temperature of hot metal at the IMF, casting commences immediately and complete dissolution of the ferroalloys is often not possible. To study this aspect in detail and to evolve suitable corrective measures, a mathematical model for the melting of a solid particle in a liquid metal bath was developed at TATA STEEL. The model was validated using the data available in literature. In keeping with published work, two separate dissolution periods were identified - a "shell period" and a "free dissolution period". The maximum thickness of the crust formed around a spherical particle shortly after immersion, can be obtained by using the mathematical model which has been developed. The model can also be used to investigate the effect of various parameters such as superheat of the bath, size of the particle, etc., on the maximum crust thickness and the particle melting time. On the basis of this study, the addition of ferromanganese and ferrosilicon was optimized at the IMF in Tata Steel.

Jan 1, 1996

By Dennis K. Mortensen

The warm southwestern desert of Arizona is an ideal location for ASARCO's new Sacaton Unit. The climate of this arid region played a major role in the design considerations of the Unit's crushing and concentrating facilities. Low yearly rainfall and relatively high yearly temperatures are a combination that was taken advantage of when designing the surface facilities. The plantsite, located due west of the mine pit, is in an area originally covered with sparse desert vegetation, underlain to an average depth of 125 feet by desert alluvium. The entire plantsite area slopes gently to the southwest at approximately 1%. Ground conditions at the plantsite area were not acceptable for construction due to the collapsability of the wetted soil when under loaded conditions, Overburden from the pit area was used to form the foundation for the entire plantsite. This waste material, entirely devoid of rock, was placed and compacted to an elevation approximately 20 feet above the desert floor. Elevating the plantsite by filling with waste material not only provided an adequate construction foundation but also eliminated the possibility of flooding from run-off in the surrounding desert areas.

Jan 1, 1974

By John J. Sammarco

This report (Safety File Guidance 6.0) is the eighth in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [5.1System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

Executive ERLE V. DAVELER. Chair u W. B. HEROY PAUL D. MERICA JOHN M. LOVEJOY WILLIAM WRAITH Finance H. G. MOULTON, Chairman H. T. HAMILTON HENRY KRUMB Admissions JOHN L. CHRISTIE, Chairman GEORGE D. BARRON, Vice-Chairman FRED H. KAY PHILIP KRAFT H. Y. WALKER

Jan 1, 1938

By Eric D. Jamieson

"How well is the Canadian coal industry able to expand in the tough competition with other fuels in Canada and with other suppliers in the international, metallurgical and thermal coal trade? Coal production as a whole decreased between 1950and 1960 and, although there has been a tripling of production since then, underground production continued to decrease until 1975. This trend has been reversed to a certain extent as a result of the modernization of mines in Cape Breton, but in 1978 over 85% of coal production came from surface mining.Against this background, the paper reviews current Canadian mining operations as described in papers presented at the 1979 CIM Annual General Meeting. Conclusions are then drawn regarding some of the longer-term mining applications in relation to the latest coal demand forecast, which indicates a potential Canadian production requirement of 160 million tonnes per year by 2000. IntroductionThe Canadian &apos;coal industry is experiencing a period of expansion and a new record for production is set with each passing year. This growth pattern over the last IS years has been based on two main markets-the generation of electricity in Canada and the export of coking coal to Japan. Supply to those markets has entailed either the development of mining, coal preparation and transportation systems for the delivery of large volumes of products with predetermined specifications or the establishment of minesite plants designed specifically to suit the characteristics of the coal in the adjacent deposits (Fig. I).Coal is a low-value commodity in relation to its bulk, and the economics of coal use become progressively less attractive with increasing distance from the producing mine. The transportation component in the export trade and in the movement of western coal to Ontario is a major cost factor. In the latter case, it approaches the cost of coal produced at the mine. In addition, the .international competition among coking coal producers chasing diminishing markets in a worldwide steel recession as well as the competition from U.S. coals and other fuel s for Canadian thermal coal have introduced a tight set of parameters to govern mining practices in all parts of the country. Some appreciation of the required changes in mining techniques brought about by declining traditional markets and the rigorous demands of the new bulk markets can be gained by comparing production from surface and underground mines over the past 25 years (Fig . 2)."

Jan 1, 1980

By W. J. Taylor

SOME eight years ago I became interested to a considerable extent in one of the well-known deposits of sulphury iron ore in New Jersey, and, as a consequence, soon became interested in the subject of the elimination of the sulphur. On investigation I found that no department of pig-iron manufacture had received less attention than that of roasting or calcining ores for the elimination of sulphur, carbonic acid, water, etc. My first devices to eliminate sulphur were naturally in the lime-kiln line, with solid fuel mixed with the ore, in the same way as common lime is burnt with small coal. While this process will succeed tolerably well for carbonates or calcareous ores, even though they contain sulphur as sulphates, I soon found it would not answer for our magnetites, which are very hard and dense, carrying from 2 to 5 per cent. of sulphur as pyrites, and become very sticky as soon as any attempt is made to roast them at a high heat. Some laboratory experiments developed the fact that the nearer the gaseous current surrounding the hot ore approached in composition pure atmospheric air the more rapidly the sulphur was oxidized, while in an atmosphere composed largely of carbonic oxide, carbonic acid, and nitrogen, it seemed almost impossible to reduce the sulphur more than one-half, which was a confirmation of the well-known fact that just one-half of the sulphur in pyrites volatilizes very easily, and that the trouble is mainly to remove the remainder. It was thus apparent that the atmosphere surrounding the ore was of as much importance as the temperature. This led to the trial of a kiln to heat the ore by conduction through the brick. It was divided into ore-chambers, which were surrounded with flues, through which the products of combustion of gaseous fuel passed without coming in contact with the ore. We did not, however, succeed by this arrangement in getting more than a cherry-red heat, which, of course, was too low to accomplish anything. I had at this point become convinced – 1st. That gaseous fuel only would accomplish the work successfully. 2d. That since a high temperature was required to insure a rapid oxidation of the sulphur, and also to make the ore open and porous,

Jan 1, 1881

By Kenneth L. Clifford

We have heard a lot during the recession about the mining industry now competing in a world market for sales of such commodities as copper, lead, zinc, molybdenum, iron ore, and phosphate. If the US mining industry is to survive, do we not have to reduce direct operating costs to a minimum? How significant is labor cost compared to consumables, electricity, fuel, maintenance, materials, and transportation? Ore grade is ultimately the dominant factor; but can we offset its dominance by improving productivity? Is the US mining industry perhaps only 25-30% as productive as it might be? What prevents the industry from being more productive? Can we retrofit older plants to be more productive or does it take a new plant with the largest equipment available for each unit operation? Present Productivity A copper industry study a few years ago covering 13 US copper concentrators ranging from about 10-45 kt/d (11,000-50,000 stpd) showed that productivity did not vary with capacity above 18 kt/d (20,000 stpd). Operating productivity varied significantly, however, from about 180-635 t/d (200-700 stpd) per operating hourly worker in most units, but one operation had 900 kt/d (1,000 stpd). Concentrators with more than 545 t/d (600 stpd) per hourly worker were in the 23 kt/d (25,000 stpd) or more category. Maintenance productivity covered about the same range, but most concentrators were in the 270¬635 t/d (300-700 stpd) per hourly maintenance worker. Again, one company stood well above others by exceeding 1 kt/d (1,100 stpd). Total hourly productivity ranged from 125-280 t/d (140-310 stpd) per hourly worker for most concentrators. The company with the most productive operation, however, was above 455 t/d (500 stpd). Salaried worker productivity for most operations was in the 725 t/d to 1.2 kt/d (800-1,300 stpd) per salaried worker range. The best operation was 2.2 kt/d (2,400 stpd). The end result is, of course, tons per day per total personnel. Most operations fell in the 110-220 t/d (120-240 stpd) range with the best operation at 400 t/d (440 stpd). This is the productivity definition that is most directly related to unit costs. Many of these operations have made some productivity progress

Jan 11, 1983

By Robert Hopler

209. Nitro-glycerine is produced by the action of nitric and sulphuric acids on glycerine, and is a heavy liquid of oily appearance, of specific gravity about 1•6, varying from colourless when quite pure to a yellow or brownish yellow. It is of a very sweet taste, and without odour, and is an active poison. Mere handling of it will in most persons induce sickness and headache. It explodes when heated to about 360° F. or from shock, but in small quantities it ignites and burns with some difficulty by the mere contact of flame.

Jan 1, 2011

By A. M. Hearn, J. G. Roos

Energy consumption, being a large proportion of the input of the ferroalloy production process, can be measured in terms of the efficiency with which the energy is utilized and the effectiveness with which it is used. The efficiency of the usage of energy revolves around the specific consumption of the energy for the production of the alloy, which encompasses the thermodynamic aspects of the process and is more of a metallurgical function that will not be addressed further in this paper. The effectiveness with which the energy is utilized is determined by the optimisation of the electricity supply from the utility (in this case Eskom). The South African electricity supply industry is on the brink of considerable restructuring, implying changes in ownership, structure and regulation. In other countries, however, restructuring has often seen higher prices. Owing to the diversity of growth prospects in South African markets, Eskom is turning to new market management and generation strategies. In future, Eskom will develop pricing strategies to increase demand from attractive customer segments such as paper & pulp, iron & steel, aluminium, and other metallurgical industries. There will be a broader spectrum of product offerings, including dynamic pricing options and demand-side management incentives. In a future electricity market that will become more dynamic and demanding, it will become increasingly important for electricity consumers to optimise their electricity supply. There are many facets in optimising the electricity supply, which include optimal utilisation of the tariff, integrating energy cost management into the production planning process, implementation of demand-side management actions, modelling, scenario planning (.what-ifs?.), optimisation, maintenance scheduling coordinated with the tariff periods, etc. This paper gives consideration to the status of the development of technology at the manganese alloy works of Samancor at Meyerton, South Africa in order to increase the effectiveness with which energy is utilized.

Jan 1, 2004

By M. Tangstad, D. Lu, G. Tranell, S. Gaal, J. Safarian

The kinetics of MnO reduction from high carbon ferromanganese slag was investigated using a sessile drop technique at 1600 ºC. The effects of reductant type, ambient atmosphere and slag composition on the MnO reduction were illuminated. Two different types of industrial reductants (ground to a particle size of 44 to 106micron and pressed to pellets) were used as substrates for small slag droplets of varying composition, which were reacted in a CO or Ar atmosphere with the reaction studied in-situ. The cross sections of the reacted slag-carbon samples were subsequently studied by EPMA to find the extent of MnO reduction as a function of reaction time. It was found that the rate of MnO reduction is affected by both the type of reductant, the ambient atmosphere and the presence of metallic components in the slag. Higher reduction rates were obtained for charcoal than for coke as reductant while a CO atmosphere unexpectedly yielded faster MnO reduction than an Ar atmosphere. It was also found that metal prills in the initial slag will increase the rate ofMnO reduction.

Jan 1, 2007

By W. H. Lewis

This Bureau of Mines report and its companion report (Information Circular 9074) have been prepared as a complete reference on underground coal mine lighting. This report discusses the fundamentals of light and its interrelationship with the visual process. The purpose of the report is to insure an understanding of the numerous complex and interrelated factors that must be considered to design and implement a mine lighting system that will satisfy human needs for good vision and comfort. Topics include history, objectives, and technical considerations of coal mine lighting; light physics; light and vision relationships; and disability and discomfort glare.

Jan 1, 1986

By C Switzer, R Logan, S Konopa, P Stoker, R Lewis

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Misima gold mine, located on Misima Island within the Milne Bay Province of Papua New Guinea, was operated by Misima Mines Pty Ltd, a subsidiary of Placer Dome Asia Pacific Limited (Placer), between 1988 and 2004. During this period, the mine produced 3.7 Moz of gold and 22.2 Moz of silver. In June 2012, the Special Mining Lease for the property was surrendered and incorporated into an Exploration Licence (EL). WCB Resources Ltd (WCB) entered into an exploration farm-in agreement with Pan Pacific Copper covering this EL.In June 2013, WCB published a new mineral resource of the Umuna deposit at Misima. All the drill hole data used for estimation was historical data collected by the previous owners of the Misima mine between 1977 and 2001. No new drilling was carried out by WCB. Confidence that the data could be relied on was provided by detailed interrogation of the existing data, reconciliation of the new resource model against production data and significant input from individuals who had previously been involved with the data collection, resource estimation and production activities of the Misima mine during its operation.This extended abstract will consider the challenges associated with locating, retrieving and validating historical data to use as inputs to produce an updated Mineral Resource estimate and comment on the material value of appropriate data storage, documentation and record keeping through the life of a project. It will also comment on the value of WCB obtaining access to the intellectual knowledge of many professionals that were former employees of Placer. This knowledge ensured that all the historical data that should have been available was sought out and accessed.CITATION:Konopa, S, Lewis, R, Logan, R, Switzer, C and Stoker, P, 2015. Misima gold mine – a case study in the use of historical data for an updated mineral resource estimate, in Proceedings PACRIM 2015 Congress, pp 579–586 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By F. C. von der Weid

The mining district of Sao Fidelis, in the northern part of the State of Rio de Janeiro, is situated on the Paraiba River, where it crosses the Serra do Mar (Mountain of the Sea), in the center of a mountainous country having numerous graphitic outcrops. For a long time, these outcrops were irregularly explored by local people, who had little means and no technical advice. A few years ago, the Cia. Brasileira de Minerasgo de Grafite took over the control of some of the more important outcrops and entrusted to me the task of studying the ores and establishing a flowsheet for a pilot plant to be situated in São Fidelis—the ore to be concentrated being mostly of a very high grade. Mineralization and Ores The rocks of the district are mostly gneiss and crystalline schists, with occasional interstratification of dolomitic limestone belonging to the Archean Brazilian Fundamental Complex. The general direction of the beds is roughly between 60" and 80°E., with variable dip, generally nearly vertical. Mostly, direction and dip of the graphitic outcrops is concordant with the embanking gneisses or schists. These outcrops seem to be aligned in two or three parallel zones (Pádua, São Fidelis, Mac- abu), the Sao Fidelis zone being the best known and the most important to date. Two outcrops of the São Fidelis zone, Saudade and Sao Benedito, are now being exploited. Mining has been carried out, so far, on a small scale. The mineralization consists of a vein of nearly massive graphite in a very compact, partially granitized gneiss, with vertical dip. The vein is most irregular, with nests and lenses irregularly distributed along the fracture plane. The ore consists chiefly (particularly in Sao Benedito) of massive graphite appearing and disappearing along the main direction of the vein, forming a succession of irregular lenses in a sort of rosary design. The average width is more or less one foot, with variations from zero to 6 feet. The lode minerals are quartz, a little feldspar and garnet (the latter having its origin perhaps in the embedding gneisses), with rare ferruginous clays on the outcrops. In Saudade a little pyrite, pyrrhotite and chalcopyrite is found occasionally, as well as a carbonaceous mineral, very light, black and shiny, with conchoidal fracture, looking like a sort of jet. The composition of this mineral has not yet been established, but it seems to be very complex. The mineralization seems to be hydro-thermal at a rather low temperature, perhaps mesothermal. The paragenesis, according to samples from Saudade, seems to be as follows, the earlier minerals being listed first: pyrrhotite, pyrite, chalcopyrite, with quartz concomitant to the three and graphite formed later. Age of the mineralization is still uncertain, owing to the very in-

Jan 1, 1948

By Bob Gordon, Allen Furth, Dan Dobbels

A 4.8 m (16 ft) diameter hard rock tunnel was driven through granite bedrock to create the 1.7 kilometer (1.1 mile) long Hampton McCloy Retention Tunnel for the city of Richmond, Virginia. During the work the tunnel encountered narrow seams of partially decomposed granite that were not self supporting and could be dealt with using ribs and lagging. However, as the tunnel approached the receiving shaft, it encountered a large seam of highly decomposed rock, alluvial deposits and running sand which resulted in soil loss into the machine. As a result of this condition, a jet grouting program was quickly developed to allow the tunneling to continue. This paper will describe the manner in which jet grouting was used to solidify and stabilize the decomposed bedrock, alluvial soils, and running sand to allow the TBM to continue tunneling.

Jan 1, 2003

By D. K. Crampton

THE object of this work was to obtain and correlate information on effect of internal stress in variously drawn tubes on several properties. Also, a simple approximate method of comparing types of stress distribution in such variously drawn tubes was sought. There is also included some work on comparison of single and polycrystalline materials and effect of different types of operation and preferred orientation. PREPARATION OF MATERIAL A series of tubes was drawn to study the effect of the type and degree of final reduction on various physical properties and the approximate distribution of stress intensity across the tube wall. The material used all came from a single heat of 70-30 brass melted in a regular production Ajax-Wyatt induction furnace. The analysis of the metal as cast was: copper, 70.36 per cent; lead, 0.04; iron, 0.02; zinc, balance. The material was cast in "shells" with 4 in. outside diameter and 3/4 in. wall thickness. It was drawn part way down according to the usual standard mill schedule and then by suitable individual schedules to finish by a variety of types and degrees of drawing to the same final cases in every instance; namely, 0.750 in. outside diameter by 0.080 in. wall thickness. The exact final draws, together with the percentage area reductions, diameter reductions and gage reductions are given in Table 1.

Jan 1, 1932

I HAVE to thank the members of the Institute most cordially for the honour conferred upon me in selecting me President, which position my poor services have prevented my filling adequately. I have, therefore only been able to stumble through my year of office under the guiding direction of our esteemed Secretary. I fully appreciate the honour done to me; and, now that it is over, I can look back with pride and pleasure at having occupied the chair; but I am told that it remains for me to fill one of the requirements of our Institute and present you with what has been dignified by the name of a presidential address. My relief in complying with this is in the knowledge of its freedom from the usual discussion which appertains to papers presented by our worthy members. It has been usual in the past for the subject chosen to be specially connected with the work immediately engaging the attention of your president, and on this occasion I would like to break away from this time-honoured custom and engage your attention for a brief space on what is equally dear to us all namely, Ideals of the Profession. In doing so, the retort of Whistler to an art student gives me, I must admit, much misgiving, for, on being asked how he developed his artistic talents, replied that he painted what he saw, which produced the immediate reply, &quot;Ah, but the tragedy will come when you see what...

Jan 1, 1909

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019