Search Documents

By J. H. Kittel

THE properties of the metal molybdenum have been the subject of recent investigations1,2 = which have included studies of the changes that occur in the metal when it is annealed after having been cold worked. Most of the data which have been reported have pertained to only one aspect of annealing, that is, the conditions under which recrys-tallization has been observecl. The process of recovery which may precede recrystallization docs not appear to have been investigated, and it is the purpose of this note to report observations on the recovery process in cold-worked molybdenum as determined by changes ill the thermoelectric power which occur as the metal is annealed. The measurements were made on commercially pure molybdenum wires which, after annealing at 1035°C in dried hydrogen for 1 hr, were swaged to give a series of reductions up to a maximum of 84.5 pct. The variously cold-worked wires were then annea1c.d in dried hydrogen for periods of 16 hr at progrc:ssively highel. temperatures from 200" to 1000 c with a final annealing treatment of 70 hr at. 1100°C. After each annealing treatment the ther.ma1 emf's were determined against a length of original unwo~,ked material that had received the initial hydrogen anrit,aling treatment. The difference in temperature between the hot and cold junctions was maintained at about 75'C. and. the thermal emf's were measured with a potentiometer that could be read. to 0.01 microvolt. Fig. 1 shows the thermoelectric power. (dE/dT) in microvolts per C between annclalcd and cold-worked molybdenum as a function of the degree of cold work. The effect of annealing is shown in Fig. 2. The general shape of the curves in both figures is similar to results which have been obtained for copper." It was observed that after annealing at temperatures as low as 200°C recovery was well under way. The rapid changes irt thermoelectric power observed near 900 C are probably associated with recrystallization, since such a relation has been observed with copper. Beyond 900°C the thermal emf's changed in polarity. indicating that from this point or1 the specimens were more highly annealed than the standard. Annealing treatments could not be given at temperatures higher than 1100°C due to limitations of the furnace, and it is evident that, since equilibrium values of thermoelectric powers were far from having been attained, temperatures considerably higher are required to fully anneal molybdenum. References Robert M. Parke: Molybdenum, A New High-Temperature Material. Metal Progress (1951) 60, pp. 81-96. * R. A. Long, K. C. Dike, and H. R. Bear: Some Properties of High-Purity Sintered Wrought Molybdenum Metal at Temperatures up to 2400 °F. NACA TN 2319 (March 1951): G. W. Brindley: A Thern-io-Electric Study of the Cold-Rolling and Heat-Treatment of Copper, Report of a Conference on the Strength of Solids. Physical Society, London (1948) pp. 95-106.

Jan 1, 1953

By M. Mortada

Nonsteady-state flow of slightly compressible liquids in porous media of non-uniform properties has been the subject of a number of recent studies. Most of these studies considered one-dimensional flow in systems with cylindrical geometry and with the properties of the porous medium varying with radial distance only. A. Houpeurt' studied the problem in its general form by examining the solutions of the differential equation, In Eq. 1, the permeability k and the porosity + are arbitrary functions of radial distance. Houpeurt concluded that, except for special forms of the functions k and the problem is not well suited for mathematical treatment, but lends itself to high-speed digital computation. Carslaw and Jaeger' discussed the solution of Eq. 1 for the case in which the permeability varies as a power of the radial distance. P. Albert3 studied analytically the pseudo steady-state solutions in systems of finite radial extent and non-uniform properties. He also obtained some numerical solutions for nonsteady-state flow using a high-speed computer. William Hurst4 examined the interference pressure drop due to a point sink located in an infinite system consisting of two permeability regions in series. In this case, the permeability changed at a radial distance r from the point sink. INTERFERENCE BETWEEN OIL FIELDS IN A NON-UNIFORM AQUIFER The interference pressure drop for oil fields located in an extensive aquifer of uniform properties is discussed in a number of places in the literature. This work considers the interference pressure drop for oil fields located in a non-uniform extensive aquifer comprising two regions of different properties as shown in Fig. 1. Region I of the aquifer extends from which is the radius of Oil Field A, to ar,,, where a>1. It has permeability k,, porosity +, and effective compressibility c,. Oil Field B is located in Region II which extends from ar, to infinity and has different properties from those of Region I, but the same formation thickness h. Region II has permeability k2, porosity and effective compressibility c2. The choice of this type of aquifer should not imply that it is of frequent occurrence. It is chosen primarily to illustrate the effects of non-uniform aquifer properties on oilfield interference. It is of interest to point out that a non-uniform radial aquifer in which both the permeability and the porosity are inversely proportional to the radial distance can be treated in a manner similar to a linear aquifer of uniform properties. The situation where only the permeability varies as the inverse of the radial distance is also amenable to analytical treatment. Both aquifers behave quite differently from a radial aquifer with uniform properties so far as the water influx and the interference pressure drop are concerned. METHOD OF SOLUTION The expression for the interference pressure drop in Oil Field B due to a constant rate of water influx in Oil Field A is developed in the Appendix. This is accomplished by the simultaneous solution of two partial differential equations describing the pressure in Regions I and 11. The two differential equations are solved subject to the following conditions: (1) at r,, the pressure gradient is constant; (2) at ar the pressure and

By M. S. Azun

M.S. Azun I have many objections to the content of the author's paper. Before discussing it, however, I would like to repeat the property of semivariogram function. Second order stationary properties of regionalized variables (ReV's) such as semivariogram function ?(h) are perfectly known in geostatistics. Also, the kriging equations in the language of mathematical statistics using second order stationary properties are well understood. However, the way to use the sample (estimated) semivariogram function in any one of the kriging procedures is vague. The sample semivariogram function is given as follows: [1 N-hy*(h) = 2(N h) i21 {Xi-Xi+h}Z, h=0, 1, N-1] where N is the total number of samples, Xi is the sample value at the i - th location, X i+h is the sample value at the i +h - th location, and h is the distance among the samples. An estimation variance of sample semivariogram function of first lag is smaller than that of higher order lag. The theoretical semivariogram function reaches the variance of samples asymptotically. But this is not easily observable because of the larger variation involved in the estimate of semivariogram function. In general, an estimation procedure is done for h = 0, 1, 2,…., up to the greatest integer less than N/2, even though sample semivariogram function can be computable through N-1. After estimating semivariogram function, the critical question of how to model sample semivariogram function arises. As seen in the above equation, sample semivariogram function is discrete and can be smoothed by the model being selected. Therefore, modeling of sample semivariogram function is the most important step in geostatistics. It not only smoothes a discrete function but also affects the results of the kriging procedure. When the only aim is to model the semivariogram function, which is the basic point of the author's paper, one can employ any fitting techniques, such as curve fitting, or any ar¬bitrary functions, which are called submodels in the paper. The term "arbitrary function" is used rather than "submodel" because there is no basic understanding of developing them. The author suggests that the sum of those submodels can also be used for the modeling of sample semivariogram function. The combination of any arbitrary functions brings many problems instead of giving an insight of the domain structure considered. The author used two arbitrary functions and the nugget effect in response to sample semivariogram function (Fig. 10). For the same example, he stated that the parameters involved in the mixed arbitrary function model can be accepted when the discrepancy between sample semivariogram function and the model is small visually. For verifying the fitting behavior of any selected model, one should not be contented with the visual satisfactory. Some statistical measure such as goodness of fit has to be used. The author's practice is no more than an exercise in curve fitting without any fundamental understanding or conceptualization of the underlying physical mechanism. Furthermore, the selection of any model is not an easy task if the purpose is the search for the "best" response to the observed second order properties of ReV's. I suggest that the Markovian model (Azun, 1983), on the basis of a theoretical understanding of underlying mechanism, which gives more information about the occurrence of regionalized variables, is used to respond all properties of ReV's. There are a lot of problems for modeling of onedimensional sample semivariogram function. Thus, it is not appropriate to go to higher order dimensional sample semivariogram function modeling. In the meantime, I would recommend that one can connect the values of standardized sample semivariogram function rather than simple values of semivariogram function in the two-dimensional estimation. The standardized values can be computed in dividing the semivariogram function value by the number of sample pairs involved in each lag regardless of the directions. In conclusion, geostatistics is an interdisciplinary area in mining that uses the principles of mathematical statistics. Thus, it should not violate any probabilistic and statistical rules. When Matheron was developing the theory of geostatistical study in the early years of geostatistics, many mining people had a reservation accepting the geostatistical tools. However, this does not mean that we, the geostatisticians, might try to convince those people using some "strange" tools or rules as some authors implied (Baafi and Kim, 1984). Instead, we have to develop and explain the geostatistical tools staying only in the framework of statistical concepts and properties. ? References Azun, M.S., 1983, "Stochastic Process Modeling of Spatially Distributed Geostatistical Data," Columbia University, Ph.D. Thesis. Baafi, E.Y., and Kim, Y.C., 1984, "Discussion - Comparison of Different Ore Reserve Estimation Methods Using Conditional Simulation," Mining Engineering, Vol. 36, No. 3, p. 280. Reply by J.M. Rendu The interactive method proposed by Rendu allows practitioners to develop semivariogram models that take into account not only the numerical information obtained by sampling, but also highly significant additional information that often cannot be quantified. The geology of the deposit - including hypotheses concerning its genesis, sampling methods, assaying methods, and mathematical methods used to calculate the semivariograms - all have an influence on the numerical results obtained and on how these results should be interpreted. If all the information concerning the spatial distribution of values in a mineral deposit was contained in the sample values, it could be argued that statistical techniques alone would produce optimum models. However, this is rarely, if ever, the case. Methods that allow the user to take into account his experience and his geologic understanding of the deposit should not be rejected for the sake of theoretical statistical purity. ?

Jan 1, 1986

By A. L. Service

In 1965 the Western phosphate industry ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock and phosphate rock products. It has become an important regional industry and, since the close of World War II, it has become important in the national phosphate economy. This report includes an evaluation of the trends and outlook for the Western phosphate industry through 1975 as part of the Bureau's program to determine the rate at which the Nation's mineral resources are being utilized. The first part of this report is concerned with the relationship between the Western phosphate industry and that of the United States and the world. It describes the principal phosphate deposits and discusses production, export, and import of phosphate rock and marketable products. The second part of the report is concerned with the Western phosphate industry and discusses trends and outlook through 1975. Projections for the utilization of phosphate rock, phosphate fertilizers, and elemental phosphorus have been developed and extended through 1975 in an effort to provide data and information pertaining to the rate of depletion of the Nation's phosphate resources.

Jan 1, 1967

By J. W. Howland

To determine their effectiveness in different climate and soil conditions, a demonstration of dozer blades specifically designed for recontouring mine spoil was conducted at an East Texas surface coal mine. The specialized equipment included a 48-foot angle blade, a modified 24-foot "U" blade, a 13-foot deep "U" blade, and a 24-foot grading bar. Both the 4b-foot and the 24-foot "U" blades were mounted in a two-tractor, single-operator configuration. To meet flotation problems common in this mining region, a 22-foot lightweight blade was developed and demonstrated for use on a 400-430 hp tractor. The demonstration involved 1,185 acres and showed a 50% reduction in reclamation costs and a 47% reduction in fuel requirements for this mine site over conventional equipment. Improved equipment, trained operators, good supervision, and improved monitoring techniques contributed to the savings. Procedures and results of the demonstration are presented and analyzed here along with guidelines for application of findings.

Jan 1, 1981

This report, the fourth in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more effectively extract and process mineral products. Environmental considerations, health and safety standards, price controls, inflation, material shortages, and more dependence on foreign imports were problems faced by the minerals industry. Although productivity increased for most mineral commodities, the annual rate of increase has slowed in recent years, indicating a maturing technological situation. Growing concern for energy resulted in increased interest and research in alternative fuel sources. The primary concerns of metallurgists were pollution control and improved efficiency and performance of metallurgical processes, especially for reduction of energy consumption.

Jan 1, 1974

By K. P. Chong

Introduction One of the requirements of processing oil shale or other energy bearing rocks is to optimize particle sizes and permeability distributions in fragmentations as indicated by Hommert (1984). Basic to the understanding and planning of in situ fragmentation and ex situ mining of oil shale are the mechanical properties. During the past six years, an innovative and unique program was established by Chong et al. (1979, 1980a, 1980b, 1982a, 1982b) that developed an efficient methodology for standardized and simplified mechanical testing of the western oil shale. The experiments include precise, representative, and duplicable sample preparation; uniaxial static compression testing; "modified" split cylinder testing; uniaxial creep and relaxation testing under extended periods of time; dynamic testing with varying strain rates; and 3-D constitutive relationships. However, as far as the fracture mechanics is concerned, as Edl (1980) pointed out, there is still a lack of understanding "of the fundamental explosive rock breakage mechanisms," which "has necessitated extensive reliance on very costly empirical approaches." Fracture mechanics of rocks and oil shale (Costin, 1981; Schmidt, 1977; Abou-Sayed, 1977; and Barker, 1977) has been based on conventional fracture mechanics using regular notched samples with limited variations of oil yields and assuming the material to be isotropic and elastic (Kobayashi, 1975; Caddell, 1980). A cylindrical double cantilever beam (DCB) specimen with a "V" slot, known as a short rod specimen, has been used by Barker (1977) to determine fracture toughness of rock materials. The inherent geometric stability of the reinforced DCB specimen makes it suitable to be used with all brittle materials. Due to its remarkable stability for the initial crack growth, the DCB specimen can be used for dynamic fracture toughness testing as well. This specimen is more suitable for the evaluation of fracture toughness at high strain rates than most other fracture specimens. However, Barker's DCB specimen is not very well adaptable for short cores or layered rocks since the specimen contains numerous layers (say in a 100-mm (4-in.) long specimen), and the rock properties change from layer to layer. Schmidt (1977) studied the fracture mechanics of oil shale with two oil yields, using notched beams. Using several independent established testing methods, Costin (1981) pioneered the investigation of the static

Jan 1, 1986

By S Pfaff, R Rajic

In the case when the number of independent variables is greater, a careful design for carrying out tests has to be made in order to obtain, with the smallest possible number of tests, as much as possible neutral information about the influence of independent variables on the dependent ones. Only on the basis of such design and its statistical analysis it is possible to come to right conclusions about the function of the whole system. The influence of pressure, temperature, humidity and granulation of the coal upon the resistance to pressure and the water absorption of the briquettes has been tested, with the aim to examine how each of the two dependent variables changes depending on the values assumed by any of the four independent variables and which of the mentioned independent variables significantly influences the dependent ones. The full factorial design with 16 experiments and the central composite design with 27 experiments have been applied. The influence of the independent variables upon the dependent ones has been examined by applying the analysis of variance. The influence values of individual factors and their interaction upon the dependent variables have been stated as well as coefficients of curvilinear equation.

Jan 1, 2003

Many persons hold the opinion that the metal indus- ries are fortuitous and that the occupation is one of sordid toil, and altogether a kind of business requir- ing not so much skill as labour. But as for myself, when I reflect carefully upon its special points one by one, it appears to be far otherwise. So wrote Georgius Agricola in 1556. He could have been espousing the sentiments of an indus- trial archaeologist investigating mining sites in 1986. South Australia has a very rich legacy from its industrial past-especially in the area of its mining history. Industrial archaeology, which is part of the broad field of archaeology, is concerned with the material and documentary remains of this industrial past. This includes the products and processes of manufacturing, industrial, technolog- ical and engineering activity and their relation- ships to people and the environment. `Archaeology' immediately conjures up the image of excavations in Greece or Eygpt. Excavation however is only a part of archaeological methodology. Industrial archaeology utilizes documentary historical rec- ords combined with field survey techniques (both above and below ground) to create a composite picture of the past. Interest in our recent past has burgeoned in Australia in the last few years. This interest manifests itself in many ways-the unprecedented popularity of Australiana and col- lecting, the plethora of Australian historic films, the growth of the National Trust, local historical societies and genealogical research. Fortunately these trends have been reflected in academic and legislative circles. Various univers- ities, institutes of technology and colleges of advanced education run courses in aspects of cul- tural resource management and conservation of the historic environment. These courses are com- prised of archaeology, architecture, geography, his- tory, materials conservation, museum studies, and national parks management and planning.

Jan 1, 1987

By S. Johnson

Introduction The mining of aggregates underground has grown steadily over the last 25 years. Growth has come in both production volume and in the importance this segment of the industry is playing in the continuing supply of construction aggregate. Underground aggregate mines will continue to grow in both number of operations and complexity, as the replacement of zoned reserves in metropolitan areas becomes crucial. This growth will result in a shortage of qualified mine managers, possibly limiting the success of these facilities. The aggregate industry will have to modify current practices in order to meet the growing demand for this specialized skill. Segment Growth Underground mining for aggregates is not a new idea. Martin Marietta has been operating underground mines since 1969, and currently operates 16 underground mines ranging in size from 250,000 tpy to 2,500,000 tpy. These mines represent less than 4% of the total number of operating locations, but contributed 9% of the annual production in 2004. Though they range in size and production capacity, the importance is evident. The 2000 United States Census revealed several trends that are of interest to the aggregate mining industry. For the period 1990-2000 the U.S. population grew by 33 million or 13%. There were nine major metropolitan areas with a population of five million or more. These nine areas accounted for 30% of the total U.S. population. More significant was the fact that the population growth in these nine metro areas was 25% of the growth for the entire country. These statistics tell us that the population is expanding in these major metropolitan areas at a staggering rate. The same thing is happening to some degree in every population center. Population growth increases the demand for local aggregate while reducing the available area to mine that aggregate. The need for an economical supply of aggregate to support community expansion is a problem that will grow as older quarries are mined out and closed. This will be an issue that communities of all sizes will have to deal with. A reliable and cost effective supply of quality aggregate is crucial to support community expansion.

Jan 1, 2006

By Rita Pinto

El presente texto señala la mineralización en la zona de sulfuros de la Minera Yanacocha. Dicha minera está constituida por Newmont Mining Company, Compañía de Minas Buenaventura S.A. (44%) y la International Finance Corporation (5%) y es el más grande productor de oro, el cual se extrae por métodos de minado a cielo abierto y tratamiento por lixiviación. Asimismo en el área de Cerro Yanacocha se presentan las típicas alteraciones de un sistema hidrotermal de alta sulfuración emplazado dentro de brechas freatomagmáticas y rocas piroclásticas. Los minerales que se presentan están albergados principalmente en la zona de mixtos y sulfuros. y se encuentran en un orden de abundancia: calcosita, covelita y cuprita asociados a remanentes primarios de enargita, covelita.

Apr 24, 2001

By Fathi Habashi

WHILE HYDROGEN SULFIDE precipitates metal sulfides from aqueous solutions, other gases such as sulfur dioxide, carbon monoxide, and hydrogen, under certain conditions, precipitate the metals directly. This can be achieved at high temperature and pressure. Such processes are of great technical importance, since metals of high purity are precipitated economically in a powder form. As a result of the availability of such powders on a large scale. processes for compacting metal sheet and other mill forms directly from the

Jan 1, 1970

By Hyde L. J

Blasting is one of the available technologies to be employed in underground excavation systems. In many instances it can be the only technology which is suitable. The recent moves towards more mechanised working systems is resulting in a reduced awareness of new blasting practices and technologies on the part of many excavation engineers. Recent developments in blasting systems can be utilised to significantly improve operating efficiency, reduce total cycle times, better comply with regional environmental constraints and reduce the total cost of underground excavation. Blasting is and will remain, a very adaptable and exciting alternative which is far from boring.

Jan 1, 1987

By Milance Mitovski, Milorad Cirkovic, Vlastimir Trujic, Dragana Živkovic

"In this article, it is analysed the possibilitis and the effects utility waste energy of process sulfuric acid production in the existing technical-technological conditions. The utility second process energy, reduction the fuels consumption, reduction environment pollution and its effects are shown, too. High heat quantity is produced as the result of exothermal reactions in the production process of sulfuric acid in Bor. A part of this heat is sufficient for the process development, and significant part of this heat presents low-temperature heat energy that is irretrievable lost. Investigations were carried out based on production of 485 t of monohydrate/day of sulfuric acid. By recovery of this heat quantity for heating purposes, about 20.000 – 25.000 t of coal/year would be saved, what would significantly improve the power efficiency of the smelter copper production. IntroductionTechnological process of copper production in RTB BOR (Serbia) produces a significant quantities of high temperature secondary (waste) heat energy that is uncontrolled “lost” in the vicinity. Secondary heat energy is produced in pyrometallurgical copper production in quantity of 1,621 kWth/kg of dry concentrate or existing heat (that presents a difference of heat at furnace outlet and heat at temperature over temperature of dew point of sulphuric acid gases) in quantity of 1,315 kWth/kg of dry concentrate. For designed capacity of Copper Smelter in Bor, the existing heat power of secondary energy is 92,111 MWt, what is an equivalent to the power of steam-turbo plant where the Rankine-Clausius heating cycle is done, and that is 28,334 MWe."

Jan 1, 2008

By I. L. Greninger

THE property of the Andes Copper Mining Co. is in the central part of the Republic of Chile, Province of Atacama, 147 km. (91.5 miles) eastward by rail from the port of Chañaral. At this point the Andean system is made up of two principal ranges. The mine is on the westerly slope of the outer, or western, range, at a mean elevation of 3250 m. (10,500 ft.). A meter-gage railroad extends from the company's port at Barquito, near Chañaral, to the reduction plant at Potrerillos. This road has a total length of 151 km. (94.0 miles), of which 93 km. (57.79 miles) are owned by the Andes Copper Mining Co. The remainder of the road is owned by the state. The company operates its trains over the portion of the road owned by the state, under an agreement with the Chilean Government. The mine is connected with the reduction plant by a meter-gage railroad, 10 km. (6.214 miles) long, which extends from the coarse ore bins at the metallurgical plant to the underground storage bins at the mine. Tunnels make up 60 per cent. of the total length of this railroad. As is characteristic of the Andean region in Chile, the topography of the locality is extremely rough, and a number of points near the mine have elevations of from 15,000 to 16,000 feet.

Jan 1, 1928

By C. J. Gilbert

The mining method at the Cannon Mine uses heading and bench stopes, which are subsequently backfilled with cemented high-strength fill prior to pillar removal. The dimensions of the pillars, 24 feet wide by G5 to 95 feet high, re-quire careful blasting in order to not damage the rock, compromising pillar strength and complicating later removal. Additionally, the proximity of dwellings makes vibration control a must for good-neighbor relations. A blast monitoring study was conducted in order to optimize bench blasting practices to maximize fragmentation, reduce costs, minimize well damage, and minimize ground vibration.

Jan 1, 1989

By Yongjun Xian

The release of fluid inclusions has a strong potential for the unintentional activation of pyrite during flotation. The present study aims to characterize fluid inclusions in a natural pure pyrite. The results indicate that a certain amount of fluid inclusions exist in the pyrite. The fluid inclusions assume a variety of shapes, including long strips, oval shapes and irregular shapes, with sizes that range from a few microns to dozens of microns. From the EDS results of hollow positions that resulted from the fracture of the fluid inclusions on the pyrite surface, certain amounts of Al, Cr, C, O, Ag and Cu were clearly detected; these elements were not detected in FeS2 pyrite itself. The contents of the inclusions were released into solution when the sample was subjected to a grinding process. Under experimental conditions of 2 g of pyrite cleaned in 40 mL of pure deionized water under an inert atmosphere, the concentrations of Cu, Fe, Cl- and SO4 2- released from the inclusions reached concentrations of 3.29 × 10-6, 32.52 × 10-6, 51.57 × 10-6 and 75.90 × 10-6 mol/L, respectively. These values are significantly greater than those from the experimental nonoxidative and oxidative dissolution of the pyrite. The fluid inclusions of pyrite were, therefore, concluded to represent the dominant sources of Cu, Fe, Cl- and SO4 2- in the aqueous solution. The present investigation provides a new understanding of the source of the unavoidable metal ions in the pulp and may benefit understanding of the flotation theory and environmental geochemistry.

By Laura A. Sanders

Mineral scale formation is prevalent in numerous mining operations. Such scale formation can occur in the direct-contact heat exchangers ahead of an autoclave. In these heat exchangers, the incoming slurry comes into contact with steam in a stage-wise fashion, which is re-circulated from the downstream flash vessels to heat the slurry in stages ahead of the autoclave. Calcium sulfate scaling causes severe problems in mining operations where increased temperatures are involved due to rising temperatures promoting calcium sulfate scaling through a decreasing solubility. In a number of these operations, the scale formation can occur in the presence of mineral solids, where fine-grained charged particles are at concentrations in excess of 35%. Scale prevention is not difficult in standard aqueous systems; however, the presence of solids leads to significant deficiencies in the prevention of scale due to the adsorption of the polymer onto the charge solids instead of the polymer interaction with the scale. Therefore, a technical solution to prevent mineral scale build up occurring in presence of pulp slurry in mining operations is needed. Several novel antiscalant technologies were developed and evaluated which provided a substantial improvement in the scale prevention in such systems.

May 1, 2013

By A. J. Miscoe, W. M. McKewan

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mimes' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in- creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 1993

By J. R. Long, C. E. Armantrout, A. H. Roberson, T. R. Graham, R. S. Dean

THE general program of the Federal Bureau of Mines on the study of alloys made with electrolytic manganese has been extended to copper-manganese-aluminum alloys. The initial results of the work are presented in this report and concern a determination of the mutual solubilities of these three metals to form the alpha solid solution. The principal studies of this system, reported in the literature, have been focused on the Heusler alloys containing 10 to 30 per cent Mn with 9 to 15 per cent Al. These investigations concern the ferromagnetic properties and the determination of the crystallization contours, with little emphasis on the phases present in the solid state outside of this area. Heusler1 recognized a breakdown of the beta solid solution of the magnetic alloy, which he says decomposes into the alpha, beta, and gamma phases of the copper-aluminum system, somewhat modified by the presence of manganese. Rosenhain and Lantsberry2 examined alloys ranging up to 10 per cent Mn and io per cent Al but were unable to reach definite conclusions concerning the phase boundaries in that area. Krings and Ostmann3 made magnetic studies and examined the system by thermal analysis. They present contours of the liquidus surface but do not place any of the phase boundaries. Corson4 [ ] has drawn a hypothetical boundary for the alpha field with few data to support such construction. The binary systems involved have received considerable attention by numerous investigators, and their general features are well established. The hopper-aluminum system (Fig, I) has been thoroughly examined by Stockdale,5 who places the limit of solubility of aluminum in copper at 7.4 per cent at the liquidus and 9.5 per cent at room temperature. Smiths established the eutectoid temperature at 570°C. by a study of isothermal decomposition of the beta phase. The copper-manganese system (Fig. 2) has been recently reviewed by Dean and co-workers.7 Using high-purity alloys, they place the solubility of alpha man-

Jan 1, 1946