Search Documents

By Munroe F. Warner

As originally built, the plant of the American Zinc and Chemical Co. at Langeloth, Pennsylvania, was based upon the Joplin and Wisconsin fields as primary sources of zinc ores, the ores being the then normal jig and table concentrates. Construction incorporated standard Matthies-sen and Hegeler kilns without regenerators. With the development of differential flotation, zinc concentrates produced by that process became the basis of operation. These concentrates were very fine, upwards of 90 per cent passing a 300-mesh screen, and had a comparatively low fusing point with marked caking and crusting characteristics. Difficulties and losses quickly developed. In roasting, the ore went through a decidedly fluid state, and spills became serious. Caking and crusting on hearths was severe and dust losses throughout became intolerable. Acid recoveries dropped from the normal ton-for-ton level to 0.85 tons per ton of ore, and choking of Glover towers and acid lines became a problem. In 1926 and 1927 a two-unit sintering plant was built and placed in operation in accordance with the Baelen process for finishing desulphuri-zation with admixture of carbon. This had its beneficial effect in smelting, but the other problems remained. The problem presented was the roasting of Pecos flotation concentrates at the rate of 200 tons daily to a sulphur content suitable for finishing in the sintering plant. Specifications had to be governed by the existing acid plant of four chamber sets built in units of two, rather widely separated, and the sintering plant built in the space between the existing pairs of kilns, of which there was one on the center line of each of the four chamber sets. The problem contained elements of pioneering and experimentation. A thermal analysis and heat balance clearly demonstrated a possibility of accomplishing autogenous roasting, well worth the attempt, because of high fuel costs and resultant economies in operation of the acid plant due to decreased gas volumes and a consequent release of capacity for increasing acid production, a problem also faced.

Jan 1, 1937

By I. R. M. Chatson

Radial layout's guiding principle is the grouping under one roof of the operating processes which require continuous supervision. Separate treatment sections are isolated by outside stockpiles fed with radiating conveyors. Hence the name "radial" layout. Many plants are designed with "linear" layout where successive operating stages are dotted like beads along a string of conveyors.

Jan 11, 1978

By Thierry Bernard

This case study shows how a unique combination of field measurements and advanced technologies allowed blasters designing, loading and firing an incredibly challenging quarry blast.

Jan 1, 2015

By X L. Liu, W Huang, J M. Zhu, S L. Wu

The shape, position and thickness of the cohesive zone have a great influence on the operational performance of the blast furnace. Many researchers have found that the high temperature properties of iron ores determine the formation of the cohesive zone. The results of this work show that sinter of high basicity interacts with lump ores and acid pellets due to the difference in chemical compositions. The softening and melting properties and the primary slag formation behaviours in the cohesive zone are improved by the high temperature interactions. The high temperature interaction is mainly influenced by the chemical compositions, porosity, interfaces and so on. Although the softening and melting properties and primary slag formation behaviours of lump ore A (a typical limonite lump ore from Australia) is the poorest of the iron ores studied, the high temperature properties of integrated burden A (consisting of sinter and lump ore A) is no worse than the other integrated burdens due to the high interaction between the sinter and lump ore A. It is useful to apply the results in the optimisation of blast furnace burden.CITATION:Liu, X L, Wu, S L, Huang, W and Zhu, J M, 2015. High temperature interactivity of iron ores in the cohesive zone of the blast furnace, in Proceedings Iron Ore 2015, pp 363–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Ramdane Bahar

The new Algiers airport building is a reinforced concrete building of more than 80 thousand square meters of floor slabs. It is located at Dar-EI-Beida, near the old passenger terminal, about 20 km east of Algiers. The project is designed to receive about six millions passengers annually and leaves the possibility of future extension. Due to the presence of a top layer of compressible soil and great concentrated loads transmitted to the foundations, the building is to be founded on 1730 bored piles of 1.2 meter diameter varying in length between 14 and 28 m. Construction work started in 1986 and was interrupted in 1996 due to financial difficulties when the structure was almost complete. The structure was left unattended for more than three years without any weatherproofing and in 1999 a new firm was appointed to complete the work and hence an evaluation of the existing structure was necessary. This paper describes and discusses the foundation design, construction supervision, site quality control and assessment by the parallel seismic method of the deep foundations built in cohesive soils. The variation in soil conditions and identified geotechnical and hydrogeological problems associated with the development of the area, required a thorough knowledge of the soil conditions. A variety of tests, involving more than 200 locations, were carried out. The ground investigation, pile tests as well as different problems encountered during piles construction, are presented.

Jan 1, 2002

By N. C. J. Ros

The paper deals with pressure gradients occurring in flowing and gas-lift wells, a knowledge of which can be applied to the determination of optimum flow-string dimensions and to the design of gas-lift installations. The study is based on a pressure-balance equation for the pressure gradient. It appears that a pressure-gradient correlation of general validity must essentially consist of two parts-—one part being a correlation for liquid hold-up and the other part being one for wall friction. Dimensional analysis indicates that both liquid hold-up and wall friction are related to nine dimensionless groups. It is shown that in the field of interest only four groups are really important. On the basis of these four groups a restricted experimental program could be selected that nevertheless covered practically all conditions encountered in oil wells. This experimental program has been carried out in a laboratory installation. Three essentially different flow regimes were found. The pressure gradients in these regious are presented in the form of a set of correlations. Comparison of these correlations with a few available oilfield data showed excellent agreement. INTRODUCTION Prediction of the pressure drop in the flow string of a well is a widely known problem in oilfield practice. Accurate data on the pressure gradient of a simultaneous flow of gas and liquid in a vertical pipe are especially useful for the determination of optimum flow-string dimensions. It is well known that with moderate gas and liquid flows such a vertical string acts as a "negative restriction". The pressure drop decreases (1) when the throughput through a given pipe increases, and (2) when at a given throughput the cross-sectional area is decreased. The reason is that, with increasing velocities, the flow becomes more agitated so that the gas slips relatively more slowly through the liquid. With the resulting increase in gas content in the string, the static head decreases. When the area becomes very small, however, the high velocities entail great wall friction, which causes an increase in pressure drop. For a given flow, therefore, minimal pressure drop is obtained by using a certain cross section. This means that, in principle, each well can be provided with an optimum flow string for minimum pressure drop and, hence, maximum possible production rate. The procedure for the selection of the optimum string has been discussed by Gilbert.' A necessary tool in the procedure, however, is accurate knowledge of the pressure gradient to be expected for various values of the governing variables. Another application of pressure-gradient data lies in the field of gas-lift practice: they provide a means of determining the optimum gas-injection rate, optimum injection pressure and optimum injection depth. Much work has already been done in the study of the pressure gradient of vertical gas-liquid flow. Poett-mann and Carpenter2 presented a pressure-gradient correlation based on measurements in wells. This correlation has been found to provide accurate predictions in high-pressure wells and in high-production wells for flow through both tubing and annuli.2-5 However, when their method is checked on low pressure-low production wells or on wells with viscous crudes, serious discrepancies are found. As we shall see in the next section, this is due to the fact that their correlation factor, representing all irreversible energy losses, is given as a function of only one correlation group. Some important variables, such as gas-liquid ratio and liquid viscosity, are not incorporated in this group so that their specific effects are not accounted for. To study also the mechanism of vertical gas-liquid flow outside the ranges covered by the Poettmann-Carpenter publication and extensions, a laboratory investigation has been carried out. This study is founded on a pressure-gradient equation that is based on a pressure balance. To reduce the number of test runs required, a dimensional analysis has been carried out, followed by a selection of relevant dimensionless groups. These groups guided a subsequent experimental study, and with their aid the experimental program could be minimized while still covering the majority of the situations encountered in oilfield practice. In this paper the choice of a formula for the pressure gradient is discussed first. This is followed by a brief description of the experimental setup. Subsequently, the dimensional analysis is discussed and the relevant dimensionless groups are selected, resulting in the experimental program required. The general relationships of pressure gradient and liquid hold-up are then described; various flow patterns and a certain flow instability (so-called "heading") are discussed and a set of correlations is presented which shows a good agreement with the measurements and a few available field

By G. Herget, O. Garg

Trends will continue towards more automated, and sometimes larger mining and haulage equipment to reduce pit development and haulage costs. To save labour costs, larger capitalization of open pits is required and pit design and stripping ratios have to be firmed up at a very early stage of mine planning. Bench failures will assume a greater importance with larger equipment and at present we have only a limited capability of predicting stable slopes in complex structural geological settings. Deep open pits will pose particular problems in regard to high toe and floor stresses. This will require the development of more efficient systems for rock mass exploration and an improvement of our predictive capability in regard to pit slope stability and appropriate management of ground- water and materials. To meet the challenge, we have to improve: a) Analytical tools to assess slope stability in structurally complex settings as found in large open pits; b) Core orientation methods during diamond drilling operations; c) Geophysical logging methods to obtain geotechnical and structural geological information for large volumes of rock; and d) Geotechnical data handling systems to define mechanical properties

Jan 1, 1983

By R. C. Gabler

Effective recycling or disposal of flue dusts is a continuing problem, particularly for secondary smelters treating low-grade Cu scrap. The Bureau of Mines investigated a variety of flue dust treatment approaches and demonstrated the technical feasibility of a bench-scale alkaline method that includes leaching, cementation, precipitation, and roasting. Flue dust was leached at room temperature with an alkaline solution of (NH4)2C03 and NHpH to solubilize ZnO and Zn metal. Some copper, lead, tin, and most of the zinc were dissolved in the leach step. Copper, lead, and tin were recovered in the cement product. The Zn in the flltrate was precipitated by pH adjustment to neutral using CO2 injection. The Zn salt was flltered from solution and roasted to give high-purity ZnO. The leach residue, enriched from 4.3 to lOA pct Sn, could find a ready market; the metallic cement product can be recycled back to the copper converter; and the high-purity ZnO product can be sold in several markets, leaving no material for disposal. The possibility for recycling of reagents, lower energy demand, and low environmental impact make this method economically and environmentally attractive for recycling secondary copper smelter flue dusts.

Jan 1, 1988

By W. A. Hoyer

Neutron activation analysis for mineral identification has attracted the attention of numerous investigators, judging from the publications on this subject in the past few years. 1-9 The appealing aspect of this method of mineral analysis is its proven sensitivity in the laboratory. In principle, activation analysis is one of the few petro-physical methods whereby a direct analysis for a mineral itself is possible in a borehole. The successful application of activation analysis requires the use of particular neutron reactions, measurement of selected gamma-ray energy intervals, and optimum bombardment and detection times. For copper analysis, Labanov et al., 10,11 using a low-energy PuBe source, reported an acceptable logging means. On the other hand, Pradzynski12, in analyzing ores and process tailings, used high-energy neutrons and photons for surface measurements of process samples. The work of Labanov et al. was based on measuring the rate of decay of the activated copper and hence was not as definitive as might be desired. Equipment is commercially available to carry out activation studies in the field 13,14 Gamma-ray spectra can be successfully transmitted over ordinary logging cables and, with borehole high-energy neutron accelerators and lower-energy chemical neutron sources, a variety of neutron activation methods can be studied. The purpose of the study discussed in this paper was to determine the feasibility and practicability of logging for copper using neutron activation techniques and commercially available equipment. The laboratory study showed that Cu could be detected in rock samples in the laboratory by high-energy neutron activation of 63 Cu. In the field, however, due in part to the large volume irradiated, the direct detection of copper using high-energy neutrons was not as promising. Detection of copper by measuring both the direct gamma-ray emission and the excessively strong low-energy gamma-ray absorption appears promising. Copper was not detected either in the laboratory or

Jan 1, 1972

By J. Y. P. Leite

In the Borborema Pegmatitic Province (Brazil) exploitations of several minerals are conducted by small producers. They use traditional techniques of gravity concentration in small-scale plants as jigs and vibratory tables. During decades the mining activity generated tailings with economic interest in particularly columbite-tantalite. Samples collected in tailing piles of a gravity plant were characterized in mineral composition, which shows in the heavy fraction the minerals spodumene, columbite-tantalite, ilmeno-hematite, garnet and cassiterite. The light fraction presents quartz, feldspar and muscovite. The degree of liberation of spodumene and columbite-tantalite were determined using optical microscopy that presents liberation in 100 µm (90% to columbite-tantalite and 100% to spodumene). Centrifugal concentrator Falcon SB-40 was used for concentration of these minerals and presents 65% recovery in mass to two stages with mass reduction about 85%.

Sep 1, 2012

By L Torckler, R L. Brathwaite

At Neavesville gold-silver (electrum) mineralisation occurs in steeply-dipping zones of intense fracturing, brecciation and quartz veining within rhyolitic pyroclastics, carbohaceous shales and andesites. Hydrothermal alteration extends over an area of greater than 3 by 1.5 km. In rhyolitic tuffs, highly silicified zones containing quartz-adularia-illite assemblages are flanked by less silicified assemblages composed of albite, illite-montmorillonite and chlorite. The mineralogy and sequence of alteration are comparable with the alteration zones which envelop the steam-producing fissures of the active Wairakei and Broadlands geothermal fields. Primary fluid inclusions in quartz from five fissure veins in the Neavesville field show maximum homogenisation temperatures ranging from 220 - 260¦C and salinities of 0.0 - 1.1 wt per cent NaCl equivalent, which cover a similar range to actual measured temperatures and salinities in geothermal fluids at Wairakei and Broadlands. The age of the rhyolitic pyroclastics and related alteration and mineralisation is probably Pliocene and Neavesville therefore represents a fossil geothermal system. The intensely fractured zones containing the gold-silver mineralisation were probably produced by hydraulic fracturing generated by accumulation under pressure of hydrothermal fluid in blind fault zones. Study of fluid inclusions indicates that hydrothermal quartz associated with electrum was deposited under boiling conditions. High grade electrum mineralisation at Graces workings appears to be localised by reaction of hydrothermal fluid with sedimentary marcasite in black shale.

Jan 1, 1980

By Sally A. Shoop

Thirty-seven blasts have been monitored using either three or four seismographs, at four coal strip mines and at a limestone quarry. Statistical analysis of the data shows that square-root, cube-root, and site-specific scaling methods predict peak particle velocities with about the same (low) degree of reliability. Some mines have peak particle velocities that are significantly lower or higher than the U.S. Bureau of Mines averages (Siskind et al., 1980). This suggests that the option provided by the proposed regulations (Office of Surface Mining, 1983), to adjust blast designs based on site-specific measurements could be highly beneficial both to operators and to the public. The frequency spectra reveal that the predominant frequencies were generally less than 50 Hz but several blasts had a significant amount of energy up to 125 Hz. In some cases the vibration energy was concentrated at frequencies corresponding to the delay intervals.

Jan 1, 1983

By W. T. Nightingale

The three gas-producing "pools" discussed in this paper are in Sweet-water County, southwest Wyoming, and Moffat, County, northwest Colorado. Hiawatha, North Baxter Basin and South Baxter Basin gas fields became economically important in 1929 when a 330-mile gas line connected them with Salt Lake City, Ogden and towns en route. This development immediately focussed attention on the gas-producing fields and the efforts of the producing company to develop them in an orderly, economical manner. Several outstanding interests were acquired and working agreements made with others. Thus the interference of natural drainage areas was avoided, the pernicious practice of drilling direct

Jan 1, 1930

By E. Stansfield

IT. has long been known that coal is unstable and oxidizes in air, even at ordinary atmospheric temperatures; also, that such oxidation affects the analysis of coal. Nevertheless little or no precaution is taken to prevent oxidation in the ordinary methods of analysis, and the possibility of error due to oxidation is sometimes ignored even in researches on coal. Although the general nature of coal oxidation is well known, and many workers have made careful studies of the rate of oxidation of different types of coal exposed to oxygen at different temperatures, yet the amount of oxidation coals undergo in the ordinary process of analysis, and its influence on the determined analysis, is not well known, and the published data are widely scattered through the literature. This paper is a collec-tion, from this laboratory, of data that bear on the subject, together with a brief summary of three methods employed here to evaluate the oxidizabil-ity of coal. The post-Carboniferous coals of Alberta range all the way from anthracite down to lignite. As some of them are notably susceptible to oxidation, the necessity for care was early forced upon our attention, and oxidation has been reduced either by the removal of air with a vacuum pump or by the displacement of air with natural gas (methane). The two routine analytical operations most liable to involve oxidation are the preliminary, partial drying of the crushed coal (called air-drying) and the determination of moisture. The first is a prolonged operation on coarse coal at ordinary temperatures, and the second a short treatment on powdered coal at higher temperatures. Oxidation also occurs in coal samples stored in ordinary sample bottles. In order to gain information for this study, determinations were recently carried out on the same samples in air, in natural gas, and in vacuo. Sixteen coals were tested; three would be classed in the United States as coking bituminous coals, two as noncoking, nonslacking, bituminous coals, and the rest as subbituminous. Table 1 gives typical analyses of these coals as mined.

Jan 1, 1934

Information Circular (IC) 9453 Roof falls continue to be the greatest single safety hazard faced by underground coal miners. During1996-99, 44 coal miners lost their lives in rock falls and nearly 2,400 were injured. In addition, nearly 6,000 non injury roof collapses were reported. Roof supports are installed to protect the miners, but support system failures contributed to most of these incidents. Reducing the terrible toll taken by ground falls continues to be a major goal of research by the National Institute for Occupational Safety and Health (NIOSH).During 2000-01, NIOSH conducted a series of open industry briefings on New Technology for Coal Mine Roof Support in Norton, VA, Charleston, WV, Evansville, IN, Tuscaloosa, AL, Price, UT, Glenwood Springs, CO, and Washington, PA. Drawing on many years of research undertaken by the NIOSH Pittsburgh and Spokane Research Laboratories, the proceedings describe what types of coal mine roof support are available, how they work, and when they should be used. The major subjects covered include roof bolts, standing roof supports, cable supports, and longwall shields. Some special topics are also addressed, including an analysis of roof fall accident statistics, techniques for better skin control, and material handling considerations. The proceedings volume also contains information on several important new technologies, which are described for the first time, e.g., guidelines for selecting roof bolt

Aug 1, 2001

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By H. Tetu, F. Pells

"The copper-molybdenum property of Brenda Mines Limited is located in the Okanagan district of British Columbia, approximately 25 miles west of Kelowna. The Okanagan Valley is a resort and fruit-growing area, and therefore pollution control measures are more stringent than in some remote areas.The Brenda plant began production in April 1970 and is operated at a rate of 24,000 tons per day. The plant site is located at an elevation of 4,800 feet, which is approximately 3,600 feet above the level of Okanagan Lake. The site is in the Okanagan drainage basin.The major consideration in the design of the system was the prohibition of any downstream discharge. It was therefore necessary to redaim as much water as possible and to minimize the addition of fresh water to the system. The maintenance of a water balance is of critical importance.This paper will outline the major design criteria for the systems and the site investigations which were carried out. The design and construction of the facilities will be de-scribed and current operating experience will be outlined."

Jan 1, 1971

By David H. Carlson, John H. Johnson

The paper presents background information, a description of mine characteristics that affect air monitoring techniques, and a review of Portable measurement techniques and instruments for gas and particulate matter sampling. A general review of the laboratory and field research being conducted at Michigan Technological University in the area of diesel emissions is presented. The facilities involved with this research are also described. These are the experimental mine, the diesel dilution tunnel test cell, the mine air monitoring lab (MAML), portable instruments, and the production mines used.

Jan 1, 1982

By L Blackwell

Strategic mine scheduling is an industry best practice for increasing the long-term value of mining operations and supply chains. The application of optimisation technology such as mixed integer linear programming (MILP) is able to achieve a mathematically optimal result for a given scheduling model. Such a model will typically define the available source material, processing options and desired constraints for accessing and processing the material. Most strategic scheduling models, however, do not include a sufficiently detailed model of capital expenditure options related to capacity expansion.Typical strategic schedule models do not include important capital expenditure features such as capacity decay or expiration (limited lifespan of trucks), precedence relationships over time (rail construction before a new plant or non-linear expansions due to economies of scale) or mutually exclusive option sets (choices of plant size). By not including these features, a strategic mine scheduling model for a capital-sensitive operation is unable to be optimised to deliver maximum value or profitability.This paper presents several results of MILP optimisation using advanced capital expenditure modelling for mining operations and supply chains. Results of the study demonstrate that optimising capital expenditure at the same time as optimising the mining schedule allows for minimisation of capital purchasing, optimal timing for those purchases and optimal scheduling around them. Overall, this results in an increase in net present value.CITATION:Blackwell, L, 2014. Capital expenditure modelling for strategic mine scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Shen Shen, Paul R. Ohodnicki, Samuel J. Kemion, Vladimir Keylin, Alex Leary, Joseph F. Huth, Michael E. McHenry

"Recent DOE workshops highlight the need for advanced soft magnetic materials leveraged in novel designs of power electronic components and systems for power conditioning and grid integration. Dramatic weight and size reductions are possible in these applications through operating at increased frequencies. This manuscript discusses processing and composition design approaches for optimizing FeCo-based nanocomposites for higher frequency operation at 100 kHz and above. The proposed strategy involves starting with prior compositions known to exhibit high inductions, optimal field crystallization induced anisotropy, and excellent mechanical and high temperature magnetic properties. Proposed alloy modifications for the applications of interest would include increased amorphous phase resistance, optimum induced anisotropy, and minimized or carefully engineered magnetostriction. Relevant process developments would target reduction of ribbon thickness by optimizing the casting process or post-processing treatments such as chemical thinning or rolling. Three archetypes FeCo-based nanocomposites are described including near equiatomic FeCo-based, Fe-rich and Co-rich alloys.MotivationSilicon steels are widely applied for 60Hz utility-scale transformers [1]. For applications at high frequencies, however, Si-steels exhibit unacceptable losses and ferrites are typically used due to their high electrical resistivity and good soft magnetic properties [2]. However, the low inductions offerrites have limited their applications in power electronics. Developments in rapid solidification have led to amorphous metal alloys and controlled nanocrystallization processing has resulted in state-of-the-art amorphous/nanocrystalline nanocomposite soft magnets [3-5]. Commercial utility-scale transformers made with Fe-based amorphous materials have been demonstrated to result in significant energy savings with an associated reduction in greenhouse gas emissions [6]. DOE workshops held in 2010 emphasized a need for advanced soft magnetic materials for the next generation of power electronics. For advanced power conditioning and grid integration applications, frequencies of 20 kHz up to -1 MHz are of interest depending on the power level [7]. Here, we review previous work and discuss the approaches to optimize FeCo-based nanocomposite materials for high frequency applications."

Jan 1, 2012