Search Documents

By W. L. Acherman

The Bureau of Mines found the chemical and galvanic corrosion behavior of the TZM and molybdenum-30 tungsten alloys to be generally equal or superior to that of unalloyed molybdenum in many aqueous solutions of acids, bases, and salts. Notable exceptions occurred in 1 [N] nitric acid, where both alloys corroded appreciably faster than molybdenum. In mercuric chloride solutions, the TZM alloy was susceptible to a type of crevice corrosion which was not due to differential aeration. The alloys were usually not adversely affected by con-tact with dissimilar metals in galvanic couple experiments, but the dissimilar metals sometimes corroded galvanically. Both alloys were resistant to substitute ocean water spray at 60° C.

Jan 1, 1968

By W. G. Dallas

The social and environmental problems presented by the location of a large zinc/ lead ore body within one mile of a thriving town are described. The development problems are social, involving the education of the in habitants , and environmental, requiring the development of a planning strategy and the evolution of a baseline and post -operational monitoring system. The necessity for an environmental-impact assessment and a thorough baseline study is emphasized. The continuing psycho-social consideration of community reaction is advocated.

Jan 1, 1977

By W. C. Schroeder

During the post-war period, and particularly during the past few years, coal production has been maintained at a reasonably constant level. This is in contrast to the greatly expanded demand for oil and natural gas. Certain markets for coal, such as the railroad and for home heating, have tended to decrease, but this decline has been offset by an increase in demand for other uses, particularly for electric power. Since the United States has very large reserves of coal and relatively limited reserves of natural gas and oil, from the conservation viewpoint, it would be better if the increased demand were to fall more heavily on coal. Where coal has lost certain markets, the decision has not always been made on the basis of price, and, in fact, in many instances, the markets have been lost where coal could show a price advantage. There are various reasons for this situation but it can be attributed in the main to the preference of certain consumers for the convenience offered by liquid and gaseous fuels. In the production of chemicals such as benzene, phenol, or ammonia, coal still plays an important role. As co-products from coke-oven operations, a wide variety of aromatic chemicals are available. In recent years, however, the production has not been sufficient to supply the demand, and it is not profitable to build coke ovens to make chemicals unless there is a market for the coke as well. As a result, the petroleum industry is beginning to take a stronger part in the production of aromatic chemicals. Natural gas has almost displaced the coke-oven water-gas machine for the production of hydrogen for the synthesis of ammonia, as well as for the synthesis of methyl alcohol and other oxygenated compounds. This information is not new and is given here only as a basis for the discussion of the broad significance of the development of the gasification process. It is clear that if coal is to regain some of its old fuel markets, as well as to maintain a position in the field of chemical synthesis, processes must be available for converting coal to the type of fuel the customer wants, and for a cheap method of furnishing gaseous raw material to the chemical industry. The operation of coke ovens and water-gas machines is not the answer to this problem for at least two important reasons: (1) the limited supply and relatively high price of good coking coals, and (2) the relatively high costs of the combined operations of coking and manufacture of water gas.

Jan 1, 1953

By A. F. Lucas

Introduction BELLE ISLE, located in the low sea marshes near Atchafalaya Bay, is the southeasternmost of the famous Five Salt Islands of Louisiana. Rising about 80 ft. (24 m.) above the level of the surrounding marsh and being some 800 acres (323 ha.) in extent, it constitutes a striking landmark on the low Gulf coast, and since the eighteenth century, when it played an important part in the operation of the buccaneers, it has been intermittently frequented by man. In 1897, the writer discovered the great mass of salt that underlies the island and shortly afterward pub-lished a brief account of the geology of Belle Isle and the neighboring salt islands.' In that paper he described principally the salt, but pointed out also the occurrence of petroleum and of sulphur in the strata above the salt. Since that time the island has been extensively explored by the drill, and the developments up to 1908 have been described by Veatch2 and Harris," and Knapp.4 The writer's early conclusions as to the probable presence of sulphur in considerable quantity have been confirmed by the later drilling, some of the wells having found quantities of gas containing sulphur dioxide and a number of sulphur-bearing strata as well. Under the stimulus of the present keen demand for sulphur for war purposes, a syndicate of New York capitalists was recently formed to explore the sulphur resources of the island in more detail. Under the writer's direction, six wells were drilled for this syndicate during the winter of 1916-17. The present paper presents briefly the results of this work and sums up the present knowledge of the geology of this highly interesting locality.

Jan 9, 1917

By John C. Luck Jr.

"DEVELOPMENT of oil emulsion mud dates back to the early days of rotary drilling when oil was added to the drilling mud solely for the purpose of freeing stuck drill pipe. After the drill pipe was freed, and drilling resumed, this oil was considered a contaminant. Efforts were made to remove the oil but some of it remained and was emulsified with the drilling mud, thus forming a mechanical emulsion.During the late 1930's, operators found that adding crude oil to drilling muds seemed to alleviate 'sticky-hole' problems and so oil was allowed to remain in the mud. This practice was adopted when it was found that faster drilling rates and longer bit life were obtained. These observations led to the development of emulsion drilling muds. During the past five years their application has become more widespread because of the lower fluid losses obtained, greater lubrication qualities, faster penetration rates, and generally better hole conditions.An emulsion may be defined as a two-phase system consisting of a mixture of either finely divided oil droplets in water or of finely divided water droplets in oil. The surrounding liquid is known as the continuous phase. The emulsifiers reduce the interfacial tension, making the droplets tend to repel each other so that they remain dispersed and stabilized. These emulsions are classified as oil-in-water or as water-in-oil, depending upon whether water or oil, respectively, is the continuous phase. Briefly, close inspection shows that they consist essentially of globules of• the one liquid suspended in a continuous mass of the other liquid. Oil emulsion muds are usually of the oil-in-water type. Two basic types of emulsifiers •commonly used in Canadian muds are soaps and lignites."

Jan 1, 1954

By O. Gunaydin

Performance measurements of large-diameter circular saws were conducted on eight different carbonate rocks in marble factories located in some areas of Turkey. Rock samples were collected from these factories for laboratory tests. Uniaxial compressive strength, tensile strength and impact strength were determined in the laboratory. The brittleness of B3 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), the brittleness of B5 (the product of percentage fines in the impact strength test and compressive strength) and the brittleness of B8 (half of the product of compressive strength and tensile strength) were calculated from the test results. Hourly slab productions were correlated with brittleness indexes. It was concluded that sawability of carbonate rocks can best be predicted from the brittleness of B8.

Jan 1, 2004

This paper describes the application of a three-dimensional finite element modelling tool to help assess the stability of a highwall at a Central Queensland mine following the weakening of its base due to highwall mining. With traditional stability assessment techniques, likely failure modes are identified on the basis of previous experience and structural, sedimentological and geomechanical data and a mechanistic analysis of these individual modes is performed. The value of the full three-dimensional model over these traditional techniques is that it provides a coherent approach to assessing highwall stability without the necessity of initially deciding upon the dominant failure mechanism and gives a useful adjunct to the traditional tools. The three-dimensional model assumes the rock mass is made of elasto-plastic blocks, incorporating possible planes of weakness, separated by near horizontal joints. The model includes the relaxation of stresses due to the excavation of the highwall and incorporates estimates of blast damage near the highwall surface

Jan 1, 1995

By J. R. Guard

Development of electrical power in coal mining has been an outstanding example of adaptbility. It has accommodated itself to new inventions, changing mining methods, increasing demands, increasing safety requirements and many other new conditions. With the appearance of the continuous miner in the mining machinery picture, those engineers interested in the application of electricity to mining have been thinking about what new comination of electrical apparatus will best suit this newcomer. It is the purpose of this paper to discuss the relative costs of supplying d-c versus a-c power to mining equipment with particular reference to continuous miner setups. Assume that a-c power will be delivered to the mine at some high voltage suitable for transmision to the various substation locations. Typical voltage for this purpose is 4000 volts. The problem then is to change the power to some kind of power suitable for driving the motors of mining equipment. For safety and other reasons the voltage to be delivered to the motor terminals must be under 600 volts.

Jan 6, 1950

By R. Chowdhury

The relevance of reliability studies for deep foundations is considered in this paper with special reference to pile foundations. Attention is drawn to uncertainties related to applied loads, the load-carrying capacity and the safety margin of a pile foundation. The essential steps in a reliability study are outlined. An essential goal of any study is the determination of the Reliability Index or Safety Index under different conditions of loading and operation. Calculations concerning probability of failure or success require an assumption to be made concerning the probability distribution of the safety margin. The significance of this and other assumptions should be clearly understood. Reliability approaches should be used to complement conventional deterministic studies.

Jan 1, 2010

By Jack A. Caldwell

Jan 1, 1985

By Jens P. Nielsen, W. H. Justice

This paper describes an improved acidizing technique which has been applied in acidizing gas wells in the La Gloria Field. Wells acidized in this manner exhibited a much greater increase in deliverahility than wells acidized in the conventional manner. The acid is injected into the well in small slugs separated by a small volume of high pressure gas. The acid and gas are displaced from the tuhing by high pressure gas to reduce the hydrostatic head on the well when the acid is recovered from the well. The well is opened for production as soon as the acid and gas are displaced. This procedure permits a very rapid recovery of the acid which results in large increases in the deliverability of the gas wells. It has been found advantageous in the acidization of gas injection wells to inject the high pressure gas directly after the acid without backflowing the acid out of the well. This practice has made it possible to inject the gas in the injection wells of this field with a much lower pressure differential. This reduces the horsepower required to inject the gas and also decrease:, the number of injection wells required per reservoir. INTRODUCTION The results obtained by acidizing gas wells ill the La Gloria Field have varied considerably in the past. For this reason. a planned study of the acidizing procedure was undertaken in order to obtain more consistent results. The Frio Sands of the La Gloria Field are rather permeable and it was not necessary to acidize many of the wells when they were originally completed. At the completion of an eight-year cycling program in several of the gas reservoirs, it became necessary to recomplete many wells in other reservoirs. It was found that the opan Flow potential of the wells recompleted in different sands was not as large as wells that were originally completted in that reservoir. A study of the drilling records of several of these wells indicated that the sands had originally been subjected to considerable hydrostatic drilling fluid overload while the well was being drilled to the deeper sands of the field. It is indicated that during this eight-year period, the drilling mud and water that were lost into the formation when the well was being drilled had formed a relatively impermeable Eone around the well bore. This impermeable zone around the well bore made it very difficult to obtain high deliverability wells when the original wells are recompleted in other zones. Muskat' has shown that in uniformly permeable and porous formations a zone of partial plugging one ft in radius around the well would drastically decrease the productivity of the well. The analysis for this problem shows that the production capacity of a well is very sensitive to the value of the permeability of the zone immediately surrounding the well bore. This is to be expected in view of the highly localized character of the pressure drop in a radial flow system about the well center. The reduction of the deliverability is not proportional to the thickness of the mud-affected zone as the major portion of the reduction in deliverahility IS caused hy the

Jan 1, 1952

By Thomas C. Atchison

The experimental work described in this report is part of a continuing study by the Federal Bureau of Mines of the fundamental physical processes involved in breaking rock with explosives. Six explosives were tested for their strain-producing abilities in a dolomitic marble. The explosives selected for testing had a tenfold variation in detonation pressure and a fivefold variation in characteristic impedance (product of loading density and rate of detonation). Strain pulses produced by the detonation of small charges of the explosives were recorded at distances of 5 to 130 feet. Peak strain, ?, was found to decrease with distance, R, in accordance with an exponential propagation law previously determined for other rock types, namely ? = (K/R)e ?aR The absorption constant, a, did not vary significantly with the explosive and was of the same order of magnitude as that for other rock types. The different explosives produced a fivefold variation in the value of the intercept constant, K.

Jan 1, 1961

By E. Mille, R. Geffken

The Mg-Si and Mg-Ge phase diagrams were rede-levtnined by thermal analysis, and the existence of a single congruent melting compound in each system was confirmed. The melting points of the two compounds Mg2Ge and ,Wg2Si were found to be 1117.4° and 1085.0°C respectively. The euteclics for the Mg-Ge system occur at 635.6°C (1.15 at. pcl Ge) and 696. 7°C (64.3 at. pct Ge); for the Mg-Si system the eutectics are at 6376°C (1.16 at. pct Si) and 945.6°C (53.0 al. pcl Si). The phase diagrams and known thermodynamic data were used to calculate activity values for both systems. The activities calculated for the Mg-Ge system agreed very well with those previously published. Partial molar enthalpy values for the Mg-Si systetn were calculated from the phase diagram for the composition region where no experimental values have been reported. THE phase diagram for any system is an important source of thermodynamic data. Steiner, Miller, and Komarek1 have derived equations which permit calculation of the activity in binary systems with an inter-metallic compound! if the liquidus and enthalpy data are known. The thermodynamic properties of the Mg-Ge and Mg-Si systems have recently been determined in this by by an isopiestic method, and it was considered that it would be interesting to compare these directly determined values with those computed from the phase diagram. The basic features of the Mg-Ge and Mg-Si systems are essentially similar. The one intermediate compound present in each system. Mg2X, crystallizes in the antifluorite structure and melts congruently. Raynor4 has accurately determined the temperature and composition of the magnesium-rich eutectic in both the Mg-Ge and Mg-Si systems. Klemm and West-linning5 investigated the entire Mg-Ge liquidus, employing sintered alumina crucibles; the purity of the magnesium and germanium starting materials was not reported. The melt was not stirred, and the temperature was automatically recorded to an accuracy of ±3°C. The authors reported large weight changes due to magnesium evaporation between 50 and 67 at. pct Mg. The Mg-Si system has been studied by a number of investigators, and the results have been compiled by Hansen and Anderko.6 Significant discrepancies exist between the two principle investigations of voge17 and Wohler and Schliephake.8 Two different grades of silicon were used by Vogel, one of 99.2 pct purity and the other quite impure, containing 6 pct Fe and 1.7 pct Al. The magnesium purity was not specified. The melts were contained in graphite crucibles with porcelain thermocouple protection tubes under an atmosphere of hydrogen. Samples weighing 10 g were rapidly heated to 50° to 100°C above the liquidus: held, and then rapidly cooled without stirring. Accuracy was ±1 at. pct which is equivalent to a maximum error in temperature of ±18°C. Wohler and Schliephake used 97.9 pct Mg and 99.48 pct Si. The graphite crucibles contained a stirrer and the 15-g samples were melted under an atmosphere of streaming hydrogen. The samples were chemically analyzed after each run. Because of the scarcity of the data, the impurity of the starting materials, and the resultant uncertainty and inconsistency in the published liquidus values, it was decided to undertake a reevaluation of the Mg-Ge and Mg-Si phase diagrams by thermal analysis. EXPERIMENTAL PROCEDURE Alloys were prepared from 99.99+ pct Mg (Dominion Magnesium Ltd.) with impurities in ppm: 20 Al, 30 Zn, 10 Si, <1 Ni, <1 Cu. <10 Fe; 99.999 pct Ge (United Mineral and Chemical Corp.), and 99.999 pct Si (Wacker Chemie Corp.). All graphite parts were machined from high-density (1.89 g per cu cm) G-grade graphite obtained from Basic Carbon Corp. with a total ash content of 0.04 pct. Boron nitride parts were machined from rods of National-grade H.B.N. boron nitride. All graphite and boron nitride pieces were baked out under running vacuum at 1100°C for 24 hr before us Cylindrical graphite crucibles (1; in. OD, 23/4 in. long, l3/8 in. ID) were tightly closed with threaded graphite covers which had 21/4-in.-long thermocouple wells and 1/4-in.-diam off-center holes for stirrers. The cover and thermocouple well were machined from a single piece of graphite. A stirrer was made from a flat cylindrical graphite plate perforated with five 3/16-in.-diam holes and a 1/2-in.-diam central hole, and was held parallel to the crucible bottom by a 1/4-in.-diam. 4-in.-long graphite rod which screwed into the plate and extended up through a tightly fitting hole in the crucible cover. An iron core enclosed in a glass capsule was attached to the stirrer with an 18-in.-long molybdenum wire, so that the stirrer could be magnetically raised and lowered from outside the system. One crucible and stirrer with essentially the same dimensions given above was made entirely of boron nitride. Chunks of magnesium were premelted, cast into 11/2-in.-diam. rods, and then cut into lengths varying from a to 1 in. A 5/16-in. hole was drilled through the center of each piece to accommodate the thermocouple well and the individual pieces were then cleaned and rinsed with acetone. The total weight of an alloy was 50 to 70 g in the Mg-Ge system and 40 to 60 g in the Mg-Si system. The pure components were weighed to an accuracy

Jan 1, 1969

Passive systems for the treatment of acid mine drainage (AMD) are typically more economic in the long term than active systems. Various flow charts for treatment selection have been prepared by scientists in the USA, however, they have typically not included a variable important at New Zealand AMD sites on the West Coast: topography and available land area. Very steep topography, dense and often protected vegetation (and animals such as snails), and a high-rainfall climate result in AMD with very high flow rates in locations with very limited space for remediation. Flow charts specific to New Zealand have been prepared which accommodate topography and available land area. Parameters necessary to use the flow charts are iron and aluminium concentrations, pH, ferrous to ferric iron ratio, dissolved oxygen concentration, topography and available land area. Prior to full scale construction, is it recommended that flow rates be quantified, small-scale trials be conducted, and cost, effectiveness, limitations, and risk of failure be reviewed for various options. One full-scale remediation system has been installed in New Zealand based on this methodology and another is planned. The performance of these systems, as well as future systems to be installed, will be used to validate these treatment system flow charts.

Jan 1, 2007

Swedish sulphide mining is presented. Dry filling is described. Fill properties with and without cement addings are dis- cussed in relation to various studies in la- boratory and in situ.

Jan 1, 1973

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, M. Mikl-Resch, R. Tichy, W. Ecker, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (fig. 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (fig. 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By Xie Gang

The leaching experiment used by bacteria on the low grade sulfide copper ore which is difficult to leach was carried out. Some leaching bacteria which have good physiological and leaching activity were isolated and domesticated, and were adapted to leaching ore. The effective domesticated method was put forward. Some technological parameters such as ore acidification, potential controlling, leaching method, ore granularity, leaching acidity, leaching liquid quantity and acid consumption were obtained by column experiment and leaching ore in situ under the ore well. The results show it could leach 30.62% of copper from the low-grade sulfide copper ore within 24 weeks by column leaching method, and the bioleaching rate of copper is 22.83% by leaching in situ under the ore well in 8 months.

Jan 1, 2006

By R. M. Brick

SEGREGATION can occur only in cast alloys that solidify over a range of temperatures with a difference in composition of liquid and solid phases within this range (ignoring monotectic systems and chemical reactions as in rimming. steels). Thus a pure binary eutectic alloy should show no segregation unless undercooling occurs for one of the solid constituents of the eutectic; e.g., chill-cast Al-12 per cent Si alloys. The phasial condition implicitly described above-solidification over a range of temperatures with a compositional difference between solid. and liquid-is found in nearly all solid solutions or combinations of solid solutions and eutectics. Metastable conditions of solidification of these types of alloys cause coring; i.e., a difference in composition between the center of a dendrite and its periphery. This composition gradient can be detected usually only by microscopic examination of etched structures; it is a "micro" effect. The gradient of more immediate industrial concern is that between the center of a cast section and the surface layers. This gross (macro) effect is usually determinable only by sampling of the casting at different points, with chemical analyses of each sample. If the compositional difference is of the same type as in coring, the first parts to freeze being enriched in higher-melting-point constituents, and vice versa, the effect is called normal segregation. When what is apparently the first part of the casting to solidify shows a higher concentration of low-melting-point constituents, the effect is called inverse segregation. These macro effects are quite separate from the micro effect, coring, yet the latter must be. described first because it is an essential part of the picture. CORING Solid Solution, Ni-Cu The nickel-copper phase diagram is reproduced in Fig. Ia, in which the solid lines represent the equilibrium liquidus 1, 3, 7 and solidus 2, 5, 8, and where the vertical 1, 4, 8 represents a 55 per cent Cu alloy. Upon moderately rapid solidification, the first dendritic axes of composition 2 (see Fig. 1b) start to form at a temperature somewhat under I. Solidification continues by growth of the dendritic nuclei, but at temperature 4 the increment solidifying is of composition 5. The rapidity of this crystal growth prevents diffusion of nickel and copper atoms from adjusting the composition of the entire dendrite at 5, which it would be under equilibrium conditions. The average composition of a specific dendrite, or the entire solid phase, at temperature 4 might be that indicated

Jan 1, 1944

By Shibo Zheng, Zhengxing Gu, Zhizhong Gao

In recent years, beneficiation tests were conducted on high dolomite phosphate samples from Florida by the authors from China Lianyungang Design and Research Institute (CLDRI). The research results indicated that flotation is the most effective process for recovering phosphate from Florida high dolomitic pebble. Other operations like scrubbing, desliming and selective grinding might work to some extent, but they could only be applied as supplementary approaches in some cases. Heavy media separation and calcination-digestion technologies are hard to produce satisfactory performance. This paper presents the results of both lab scale and pilot plant tests on Florida high dolomite phosphate pebble using the fine particle flotation technology developed by CLDRI. Some discussions are made on the concerns of Florida phosphate industry and further research.

Jan 1, 2002

By R. A. Lowe, P. B. Malla

Smectite is a common impurity in the kaolins of Georgia.This impurity is harmful to the low-shear rheology of kaolin slurries in concentrations as low as a few weight percent. The deleterious effect of smectite on the low-shear rheology is due to the swelling of the mineral. Montmorillonite containing clays were treated to precipitate a compact brucite layer {Mg(OH)2} in the interlayer region of the expandable layer silicate mineral. This treatment forms ahydroxy-Mg-montmorillonite with characteristics similar to chlorite. This treatment effectively reduces the swelling capacity of the mineral and improves the rheological properties of kaolin slurries contaminated with smectite impurities.

Jan 1, 1999