Search Documents

By T. D. Rourke, Fred H. Kulhawy, O&apos

From mid-1976 to early 1978, a 5.64 m diameter tunnel, 2491 m long, was excavated by a modified Robbins full-face TBM under shallow cover in highly stressed sedimentary rock in Rochester, NY. In-situ stress measurements were made, and tunnel behavior was monitored with MPBXs, inclinometers, tape extensometers, and instrumented steel ribs. Detailed geologic mapping was also done. In this paper, the as-monitored tunnel behavior is described, and the TBM performance is evaluated from field records. Recommendations are also made for future tunneling in similar geologic environments.

Jan 1, 1981

By C. Legote

"This paper investigates the conditions leading to the indefinite termination of production in four critical primary panels at an underground coal mining operation, the observed shortcomings in the mining approach, and the proposed strategy to mine through the affected panels. Initial assessment of the abandoned panel conditions indicated time-dependent strata failure,(i.e. bolted roof failure overrunning intersections), which occurred from mere minutes to up to four weeks post-production, with and without prior warning of failure. This prompted the constant re-supporting of back areas, which raised safety and productivity concerns. Investigation of the initial mining conditions revealed that the failures were due to a critical combination of factors, the chief of which was isolated horizontal stress. Other factors that were initially overlooked by the mine (i.e. influence of hydraulic stress, misinterpretation of borehole data), resulted in the conditions being described as abnormal. Remedial actions were determined, and in so doing, a new strategic approach was formulated to thoroughly address all failure concerns. The four panels were explicitly planned to serve as the main intake and return airways for the recently commissioned secondary ventilation shaft, as well as providing access to millions of tons in proven coal reserves. It is thus imperative to mine the panels. A feasibility study showed that the proposed strategy set for implementation would be financially viable. Paper written as project work carried out in partial fulfilment for BEng(Mining Engineering) degree"

Jan 1, 2015

By Marco Le Roux, Martha Van Rensburg, Quentin Campbell

Fluidised bed drying is currently receiving much attention as a dewatering option during the beneficiation of fine (defined here as between 1 mm and 2 mm particles) coal. Apart from concerns about safety and combustion, the operating costs can be high if very high gas or air temperatures are used. The aim of this study was to investigate the removal of moisture from fine coal by using air at a lower temperature (25 - 55°C) within a controlled environment by lowering of the relative humidity of the air. It was firstly proven that fluidization has a major advantage over non-fluidized beds, with regards to drying rate and final moisture content. Hereafter several parameters that influence the dewatering rate and final moisture content were tested, from which it was concluded that the relative humidity of air acts as the largest driving force for dewatering. Parameters tested included relative humidity, temperature and coal composition. Energy balances showed a positive nett energy increase in the dried coal during combustion when related to the energy input during drying. In comparison with thermal drying technologies, fluidized bed drying was proven to be less energy intensive. It was therefore shown that this is a viable technology for the dewatering of fine coal.

Jan 1, 2014

CONTENTS PAGE THOENEN, J. R.-Limestone Production as a Mining Problem. Discussed by Oliver Bowles, J. T. Singewald, S. R. Russell 1 GRIGGS, C. C.-Engineering in Limestone Production. Discussed by W. C. Phalen, John Rice, Samuel M. Shallcross, Oliver Bowles, Nathan C. Rockwood, George Milliron 2 WILDER, FRANK A.-Rotary Calciners for Gypsum. Discussed by L. K. Arm-strong 9 PORTER, JOHN J.-Manufacturing Problems of Cement Industry. Discussed by Samuel M. Shallcross 9 KIRKHAM, VIRGIL R. D.-Phosphate Deposits of Idaho and Their Relation to the World Supply. Discussed by F. A. Wilder, S. L. Willis, G. R. Mansfield, R. W. Stone, L. K. Armstrong 9 Limestone Production as a Mining Problem Discussion of the paper of J. R. THOENEN, presented at the New York Meeting, February, 1925, and issued, as Paper 1417-H, with MINING AND METALLURGY, February, 1925. OLIVER BOWLES, New Brunswick, N. J.-I am so thoroughly convinced of the growing importance of underground work in the production of limestone that I had the author make a detailed study of limestone mining for the Bureau of Mines and prepare a report on the principles of limestone mining. Many limestone operators, long accustomed to open¬pit work, are being forced to mining. About 6 months ago I thought there were twenty-five or thirty underground limestone operations in the United States but the author has been finding new ones until his list now runs nearer sixty. Some of these are very extensive; one at least has 4 ½ miles of underground workings. There is an ever-expanding field for the engineer in the operation of limestone mines and quarries. Some of the larger companies realize the need of skilled engineering advice, but many of the companies regard the engineer as an unnecessary expense. Although almost every metal mine, even those handling only a few hundred tons of ore per month, employs a mining engineer, many limestone operations ten times as large employ no mining engineers. Few mining engineers are at all familiar

Jan 6, 1925

By H. J. McQueen

Pressure welding is a solid state joining technique that depends on bringing the parts into sufficiently close contact that inter-atomic bonds are achieved. Pressing is more effective at elevated temperatures where plastic flow causes the asperities to collapse; improved application conditions are derived from hot-work research to clarify temperature and strain rate dependence of hot strength and ductility. The substructure evolution systematically studied in hot working to determine dynamic recovery or recrystallization is applied to clarifying that developed in welding. The various processes are affected differently by work-piece geometry and final shape requirements. In addition to pre-cleaning of the surfaces, the plastic flow helps disperse the remaining oxide layers as was originally exemplified in blacksmith hot forging of layered sword blades and in bellldie welding of wrought iron tubes. The presentation critically compares the utility for various materials and configurations of simple pressure, ultrasonic application, diffusion, explosive, rotary and linear friction and friction-stir processes. Diffusion bonding (primarily Ti) with light cleaning, low pressure, little distortion in protective furnace atmosphere contrasts strongly with the heavy upsetting in friction welding, or complex alloy mingling and substructure variations in friction stir joints.

Jan 1, 2011

By Robert H. Lambeth

There are no identified mineral resources in the Italian Peak RARE II areas, and there are no producing or developing mines within or adjacent to the study area. Several prospects are in RARE II area M-4945, Idaho, but none were found in the area I-1945, Montana. The Viola Mine (fig. 1, no. 15) vicinity and the Heart Mountain vicinity along the west and south borders, respectively, are being prospected. There has been no recorded production from mines within the study area, but between $2.5 million and $5.0 million worth of lead, silver, and zinc were produced in the adjacent Birch Creek district - dominantly from the Viola Mine - from 1882 to 1889 (Anderson and Wagner, 1944, p. 14). The Viola and other mines in that district are possibly, on basin-margin, carbonate-hosted, lead-silver-zinc deposits stratabound within the Devonian Jefferson Formation. Previous studies have considered them to be hydrothermal, replacement orebodies. Mineral occurrences in the Heart Mountain area are possibly black-shale hosted uranium-vanadium deposits in the Mississippian-Devonian McGowan Creek Formation or perhaps the underlying Devonian Three Forks Formation. The Jefferson and McGowan Creek Formations underlie many scattered segments of the study area. The deposits and occurrence; are not sufficiently exposed to determine tonnage and grade, but sampling indicated moderate resource potential at two properties just outside the study area, the Viola Mine and the Elkhorn Group (fig. 1, no. 33). Local residents indicated there are several thousand tons of zinc-bearing resource; at the Viola line. A 23-ft (70-m) drill hole intercept near Heart Mountain et the Elkhorn Group adjacent to the stuny area contained 0.15 percent uranium oxide

Jan 1, 1983

More than 400 members and guests registered for the 146th General Meeting of the Institute held in Mexico City Nov. 9 to 15, inclusive. Of these, 250 came by special train or automobile from 24 states of the Union, and the others were resident in Mexico. Mexican Government officials, headed by Manuel Santillan, Sub- secretary of the Department of National Economy, acting in. behalf of the President of the Republic, and including the Secretary of Foreign Relations and the Governor of the Federal District, were most hospitable in their official welcome and provided splendid entertainment of various kinds. A reception was tendered by Hon. Josephus Daniels at the U. S. Embassy. Among other hosts were officials of a number of large operating companies, including M. H. Kuryla, of the Real del Monte company; Jules Lacaud, of the CompaiLia Minera de Chontalpan; and Harry Wright, of the Consolidated Steel company.

Jan 1, 1937

By J. van Wijk

"Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems (VTS). To investigate flow effects under realistic conditions, especially clogging effects, a 136 m high test facility for flow analysis in vertical transport has been constructed using available mining infrastructure. Tests are run in a closed circuit, using a system of downfall and riser pipelines connected to a compact sediment injection- and separation unit as well as the centrifugal pump. The riser is equipped with pressure sensors, as well as temperature sensors, flow meter, concentration meter and high speed camera to allow comprehensive analyses of the flow regime and behavior of transported material within the flow. Additional mobile measurement devices allow wear and tear analyses of pipe material. This paper focuses on the determining factors of the tests leading to the design as well as the installation and trial of the test facility itself and explains the used components and work principles. INTRODUCTION Since the 1970s several research projects had been conducted investigating in the possibility of deep sea mining. In recent times projects for deep sea mining operations have started again, considering the rising demand on natural resources, especially raw earth elements. Yet projects like the Nautilus project on the deposit Solwara 1 [1], or Japanese projects focusing on the region of Okinawa [2] and Chinese projects [3] planning on depths of “only” about 2,500 up to 3,000 m. Until now no economical deep sea mining project was realized, due to the enormous difficulties of deep sea environments. Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects, considering transportation heights up to 5 km. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems or VTS [4]. Critical parts of the system would be identified and investigated to deliver solutions and higher the technology readiness level to a level were planning of a pilot project can be considered. At first case examples for mining projects of seafloor massive sulfides (SMS, 1,600 m water depth) and manganese nodules (MnN, 5,000 m water depth) had been calculated on basis of economical frame conditions, such as planned production rates to be efficient. As depicted in Figure 1 two major possible systems had been used for comparison, airlift system and pump system, considering multiple pump stations or single pumps. Based on the results and comparisons for the calculated vertical transport systems critical components and flow effects had been identified."

Jan 1, 2018

By Chang JF

This paper describes the advance in shaft sinking technique in terms of a vast complex of equipment in the last decade, and mainly recommends some ad- vanced technology and a vast complex of equipment, such as smooth blasting, la- ser guiding, shot-crete lining and rock- bolting, hanging bracket ring for drills, large-capacity wall grab, tipping device, storage bunker, and automobile haulage et.al., finaly, author in detail repre- sents some successful applications of advanced shaft sinking technique in some mines as an example.

Jan 1, 1987

By Cary Hirner, David Stacey, William A. Rochford

Design considerations and construction techniques were implemented to address groundwater infiltration from a confined aquifer during the excavation and lining of the Cady Marsh Flood Relief Tunnel. This 3-m finished diameter, 2-km long tunnel was successfully completed cost-effectively in an urban setting near East Chicago, Indiana. The soft ground was mined using a conventional tunnel boring machine with hydraulically actuated flood doors and supported with steel ribs and timber lagging. The tunnel was lined with cast-in-place concrete. Dewatering was implemented in settlement prone, boulder-laden ground in residential neighborhoods during construction to depressurize and partially dewater the aquifer at the tunnel horizon. This paper describes the design decisions and construction methods utilized to mitigate and limit infiltration into the tunnel during construction and operation, as well as manage ground settlement.

Jan 1, 2007

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

5. Development of Initial Probing System 5. 1 Introduction The preliminary evaluation of a variety of potential methods for initial probing showed that the optical system using closed circuit television (CCTV) and the sonar, or acoustic ranging, system were the most promising. The former is capable of pro¬viding a visual display of the mine passages in a clear, non-smoky environment, and the latter is capable of providing a map of the spatial location of the coal surfaces making up the entries, as well as objects, such as cribs, mining machines, etc., in the passages in both smoky and non-smoky environments. The sonar system used in conjunction with the CCTV in a clear environment can greatly assist in resolving the spatial distribution of objects seen on the TV screen. Further, in a smoky environment the interpretation of the sonar information could be facilitated if some visual information were also available. CCTV systems exist but require some modifications to suit this particular application. The Industrial Hazards and Communications Division of the Bureau has an ongoing program for the development of such a CCTV system. Rather than duplicate this effort in developing a CCTV system, it was decided to evaluate the possibility of utilizing their system for initial probing, while continuing with the develop¬ment of a system which would work in any environment, including the presence of dense smoke. The concept of using sonar for the initial probing of mine passages represents the application of new technology requiring development. The results of such a development effort undertaken during the course of this program are described in the following sections.

Jan 1, 1973

By J. P. Ferro, W. H. Stewart

Wet ground and dry muscovite mica continued to be the most commercially significant types of mica in the US. Canada's phlogopite mica and some US deposits of sericite mica have also contributed to the overall application of mica in a variety of industries. Mica's major end uses are paint, rubber, and construction material. Its value was about $30 million last year. The southern Appalachian Mountains weathered granitic bodies and pegmatites continued to be the primary US muscovite mica source. North Carolina production of mica as a coproduct of feldspar, kaolin, and lithium processing accounted for more than 60% of the total output. New Mexico, South Carolina, South Dakota, Georgia, and Connecticut accounted for the rest. Flake mica was also produced from mica schists in North Carolina and South Dakota. It is also being investigated in Ontario, Canada. Wet ground mica Wet ground mica was produced by four companies: KMG Minerals, Franklin Mineral Products, J.M. Huber Corp., and Concord Mica. KMG and Franklin Mineral Products accounted for more than 80% of the production. Wet ground mica is a highly delaminated platey powder used to reinforce solvent and aqueous system paints for increased weatherability, durability, and greater resistance to moisture and corrosive atmospheres. In plastics, it is an excellent filler and reinforcing agent, providing better dielectric properties, heat resistance, and added tensile and flexural strength. In the rubber industry, wet ground mica is used as a mold lubricant to manufacture molded rubber products, such as tires. It also acts as an inert filler that reduces gas permeability. Miscellaneous uses include additives to caulking compounds, foundry applications, lubricants, greases, silicone release agents, and dry powder fire extinguishers. Wet ground mica prices range from $353 to $496/t ($320 to $450 per st) fob plant. Specialty products may be higher, depending on customer requirements. Dry ground muscovite mica Dry ground mica was produced by nine companies: KMG Minerals, Unimin, US Gypsum, Mineral Industrial Commodities of America, Spartan Minerals Corp., Asheville Mica Corp., Deneen Mica Co., Pacer Corp., and J.M. Huber Corp. Dry ground mica's primary market is wallboard joint compound. Here, it is a functional extender that improves the physical properties and finishing characteristics of the mud. It is also used in various grades as a filler in asphalt products, enamels, mastics, cements, plastics, adhesives, texture paints, and plaster. Dry ground mica became popular as an additive in oil well drilling fluids, where the mica flakes platey nature helps seal the well bore, preventing circulating fluid loss. But oil's dramatic price drop and consequent curtailing of well drilling brought this once booming market to a virtual halt. Forecasters predict that this business will gradually pick up during the next few years and most current dry ground mica producers will again produce the oil well drilling material. Dry ground mica prices range from $110 to $420/t ($100 to $380 per st) fob plant. High quality sericite mica, sometimes referred to as an altered muscovite, was mainly produced by two US companies. Mineral Industrial Commodities of America and Mineral Mining Corp. have equivalent capacities of about 27 kt/a (30,000 stpy). The majority of the material produced was consumed by the joint compound industry. Minor uses are in paint and oil well drilling. The lack of ground sericite penetration into the traditional ground muscovite markets is attributed to high silica content, typically in excess of 20%, and a bulk density. Prices range from $88 to $187/t ($80 to $170 per st) fob plant. Phlogopite mica is a dark colored, magnesium bearing mica rarely found in the US. Suzorite Mica Corp., a division of Lacana Petroleum, mines a deposit in Quebec that is 80% to 90% phlogopite. The dark color has prevented the material's entry into the traditional paint markets. But the physical properties and high purity make it useful as a low-cost reinforcing filler in many plastics and several asphalt applications. Phlogopite mica is ground to several grades and may be treated with various surface coatings for use in plastics or coated with nickel for EMI/RFI shielding applications. Prices for phlogopite products range from $144 to $580/t ($104 to $580 per st) fob plant. As in recent years, production of domestic muscovite sheet - block, film, and splittings - remained insignificant. These resources are limited and uneconomic due to the high cost of hand labor required to process sheet mica in the US. Imports from India and Brazil were the primary sources of the estimated 1 kt (2.4 million lbs) valued at $2.5 million consumed by US electronic and electrical equipment manufacturers in 1986. Reserves As a feldspar, kaolin, and lithium industry coproduct, flake mica will continue to provide a large percentage of mica re- This summary of 1986 mica activity was received too late to be used in the June issue.

Jan 7, 1987

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

By Jerry Ran

When multiple levels are mined in open stope mining with delayed backfill, mining underneath fill is inevitable to achieve higher rate of recovery if no sill pillars are left for the purpose of fill separation or partial ground support. This is particularly true when the orebody has low reserves per unit vertical distance. Instability of the exposed fill back causes stope dilution, production delay and possible equipment damage and consequently increases the mining cost. Previous studies have concentrated on fill mat stability in cut-and-fill and stability of fill walls in open stope mining. Workers are exposed to the fill back in cut-and-fill and therefore smaller open spans are normally adopted and the fill mat is reinforced. In open stope mining openings with large spans are designed, workers are not exposed to the fill back and its stability has to be maintained by fill of sufficient strength. However, the required fill strength is normally determined by considering different modes of fill wall failure. The fill back stability is usually not analyzed in the fill design process. The lack of analysis on fill back stability for open stope mining is mainly due to difficulties in relating the fill properties to the fill and stope geometry. In this paper a simplified wedge model is adopted to analyze stability of the exposed fill back in open stope mining with consolidated backfill. The proposed method calculates the factor of safety of the fill back against shear failure under known fill and stope geometry and fill strength parameters in order to assess the fill back stability. It can also be used to determine the required fill strength with known fill and stope geometry. The proposed approach is indirectly validated by mining experience and observations at two operating mines. In addition there are many factors affecting the fill quality and stope configurations in an operating mine. These factors have to be considered in the analysis of fill back stability. This situation is highlighted by presenting an actual mining case where the fill back failed due to factors commonly encountered in mining operations.

May 1, 2003

By George B. Langford

THE McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dikes of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compressive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed-an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitit,e dikes.

Jan 1, 1938

By L. Ozdemir, M. Cigla

This paper presents and discusses some of the computer models developed and currently used at the Earth Mechanics Institute (EMI) of the Colorado School of Mines (CSM). These include the performance models for full and partial face machines. Examples of input and output of these models will be illustrated for typical mining operations by using machines such as Tunnel Boring Machines (TBM), Continuous Miners (CM), Marietta borer miners and longwall drum shearers. The general approach to modeling and the available models are discussed and some examples of these models are presented. The comparison between the estimated and achieved performance, as well as the degree of improvement in the performance due to balancing and modification in cutterhead design are also discussed.

Jan 1, 2000

At the Orieco mine quartz veins carrying sulphides were localized in parts of an extensive fault zone in the Mathinna Beds during late Middle Palaeozoic mineralization.These deposits were subsequently exposed, and oxidation of the sulphides by percolating groundwaters resulted in the formation of gossans at the surface, and replacement close to the permanent water table of the more soluble sulphides by copper sulphides (chalcocite, coveIlite). A restricted zone containing copper oxides (cuprite, tenorite), copper carbonates (malachite, azurite), iron arsenates (scorodite, pharmacosiderite) and possibly rare copper sulphates occurred above the water table.The renewed oxidation of these deposits following mine development has been facilitated by the ready circulation of air and water combined with the formation of large free surfaces ideal for evaporation of aqueous solutions. Under these new conditions of high initial sulphate concentration, low pH, and relatively high Eh, the previously formed mineral assemblage is unstable and numerous Cu (Fe,Zn)-sulphates and Fe (Cu,Pb)-arsenates are presently forming in fractures in the fault zone and on the adit and stope surfaces for some considerable distance from the Sulphide-rich ore shoots. The observed spatial sequence of the major sulphates with respect to the sulphide-rich zones (Le. chalcanthite-antleritebrochantite and langite) is consistent with decreasing sulphate concentration and increasing pH away from the oxidizing sulphides.

Jan 1, 1970

By L C. Pretorius

Pipe pigging is a technique for the in situ (field) coating application, to create a seamless internal anti-corrosive lining of long pipelines. The technology originated in the cleaning of pipes, and these proven cleaning methods continue to be used today. Firstly mechanical cleaning of the pipeline is performed, using wire brush, razor back, course stud and fine wire pigs, then foam pigs, or criss cross pigs, and urethane blade scrapers to remove loose debris, wax, residual hydrocarbons and corrosion products from the pipeline. Part of the proprietary techniques and expertise is to ensure that these cleaning pigs do not get stuck Next chemical cleaning of the pipeline is performed, using repeated pig runs with detergents, solvents, acid etching, corrosion inhibitors, consecutively batched between two pigs, to ensure a clean, dry metal finish to a visual cleanliness standard of ISO SA2½. These in situ techniques were developed, 40 years ago to apply internal corrosion protection to pipes using a thin layer of epoxy based paint (50 to 100 micron). Until recently these old techniques were never improved upon. Although many thousands of kilometres of pipes were successfully coated with these thin film epoxy based paints and old application techniques, these thin paint films had problems in weld coverage, and were also unable to fill pits caused by pitting corrosion, and unable to replace metal loss caused by channel erosion. New coating material developments, revised application methods and modified pigging equipment have now made it possible to apply thick film coatings as corrosion barriers to the internals of pipes in the field, using these pigging techniques. The thick coating films can be up to 1 mm (40 mils) thick in a single coating run over long distances. The new thick film coating materials and application techniques are similar to continuous screeding, creating a far more robust seamless internal pipe lining when compared to the old technology of thin film paints. With thick film polymers the option now exists to create a structural GRP pipe within a pipe, be it steel or cementicious. It has been preferable, even necessary, to move away from the traditional epoxy paints and coatings. It was found difficult or impossible to use epoxy materials for these pipe coating applications due to the requirement for achieving a suitable viscosity with adequate hold up. In order to reduce epoxy viscosity a solvent or reactive diluent is required. This inevitably lead to solvent entrapment and poor cure characteristics in cold climates. Further mud cracking in over thick areas, the inability to extend or reduce pot life, poor control of cure time and limited resistance to aggressive or chemical environments made solvent based epoxy resins a poor choice.

Jan 1, 2006

By Moris Fresko, Julia Sun, Charles C. Golembewski, Vytas Svalbonas

"A history of mill strain gaging at Metso is presented. The output of these strain-gaging programs is compared with calculated stress ranges from different finite element solutions. These comparisons expose the amount of approximation that exists in the analytical solutions, starting from geometry, and material properties, and ending with different forms of internal load models. The influence of strain gaging results on mill design and analysis practices is also discussed. While these instrumentation programs are valuable in identifying areas of high stress in mills, and locations of stress concentration factors, they are by no means extensive or comprehensive enough to verify general internal load models. The vast majority of the programs were aimed at getting additional data about potential failure points, rather than describing overall mill stress behavior. This is especially true since the more recent gaging programs have not included the difficult task of gaging the mill rotating structure interior. This paper tries to avoid the novice path of leaping to general conclusions on the basis of insufficient data."

Jan 1, 2014

By Pedro G. Salom

I HAVE had an opportonity, within the last few months, of making a large number of physical and chemical tests of steel for boiler and ship-plate, which has been, and is now being, used principally for the United States Government cruisers, now building in Mr. John Roach's yard, at Chester, Pa. Through the courtesy of the Messrs. Houston, of the Chester Rolling Mills, I have the honor to lay before the members of the Institate the results of these tests. These results have developed some points in regard to the nature of steel, which are more or less new, and which, I hope, will prove interesting. The original specifications, as regards the manner of testing, were so inipracticable (when their severity mas taken into consideration), that the keel of the first vessel, which will be launched next month, would, had they been carried out, probably not have been laid until next year. At my suggestion, in order to simplify and expedite the immense amount of testing that had to be done, the Naval Advisory Board was induced, after considerable discussion, to alter the specifications, so as to test each heat, instead of each lot of twenty plates, but reserved the right of making the quenching-test on a piece from each ingot, after it had been rolled. This relieved us from the anxiety of having a lot of plates rejected, after they had beell rolled and sheared, by reason of the presence of one or two plates which might have been injured in heating or rolling, or which might not have been able to stand the tests; while it insured the Government in obtaining a uniform quality of steel, and prevented the temptation to introduce a half-dozen or more had plates in a lot, and run the risk of their being selected as the testplates. I give below a portion of the original specifications, as prescribed

Jan 1, 1884