Search Documents

By Anders Salwén

In 1975 T. Nishizawa and A. Chiba reported on observed deviations from the ferrite-austenite local equilibrium in several diffusion couples based on the Fe-Cr system. In order to try to verify these results the austenite-to-ferrite transfonnation in a Fe-20 %Cr-Invalid Code [Fe-]-%Cr diffusion couple held at 1100 for 100 hours has been simulated. The simulation model is based on the postulated principle of maximum dissipation rate of Gibbs energy during transformation, which allows non-equilibrium interface conditions. Keynotes: Computer Simulation, Austenite-to-Ferrite Transfonnation, Diffusion Couple

Jan 1, 2003

By Kezhuan Gu

Data on the kinetics and thermodynamics of dephosphorization are analyzed in terms of the dynamic partition ratio, determined by a combination of slag thermodynamic properties and the balance of oxygen supply and consumption. A recently developed phosphate capacity correlation is combined with data on kinetics to quantify the most significant parameters in controlling the interfacial oxygen potential. The role of slag composition, entrained gas fraction and temperature are discussed in addition to metal carbon and sulfur content. It is demonstrated that the mass transport of oxygen in the slag is enhanced by factors increasing conductivity and inhibited by entrained gas. The mass transfer of phosphorus in the metal is described considering surface renewal induced by CO bubbles.

By L. B. Tsymbulov

At present data on thermodynamic properties of metallic melts, containing copper and ?iron family? metals, is rather limited. Determination of the activity of metallic melts components under high temperature by experimental methods requires high level of labour inputs. With this it is not always possible to obtain the results with high level of accuracy. Due to that in a number of cases it is more appropriate to apply different methods of analysis, with the help of which there can be calculated thermodynamic properties of ternary and even more complicated systems, prominent thermodynamic properties of binary systems being used as a basis for these calculations. This work presents the results of calculations of different components activity and activity ratio in such ternary system melts as Ni-Cu-Fe, Ni-Cu-Co, Fe-Cu-Co and Fe-Co-Ni. Good compliance of calculations results with those obtained in the course of reliable experimental investigations fulfilment is demonstrated. There are presented the results of activity and activity ration analysis for some compositions of Cu-Ni-Co-Fe system.

Jan 1, 2006

By Maria I. De Rosa

The U. S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (~300° C) and later (~400° C) combustion stages of chlorinated polyester-reinforced mine ventilation ducts could be predicted by a smoke particle characteristic, for the development of a test parameter. The experiments were conducted in an approximately 20-L furnace, at 14-min durations at set furnace temperatures of 2500 and 1,000° C, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were the hydrogen chloride (HCI), carbon monoxide (CO), carbon dioxide (C02), and oxygen (02) concentrations, furnace temperatures, the sample mass weight loss, the average smoke particle diameter (dg and average number and concentration (no), and the product of the average smoke particle diameter and concentration (dgno). Results show that the inverse of the smoke particle diameter-concentration product [(l/dgn0)], correlates directly and significantly with the primary gas toxicities evolved during both early (HCI) and later (CO) stages of combustion.

Jan 1, 1989

Allen & Garcia American Mining Congress American Steel and Wire Company Blue Blaze Coal Company Bogue Supply Company Brandenberger, L. Burke Company, J. J

Jan 1, 1929

By James A. Pendleton

The Legislature of the State of Colorado adopted House Bill 1223, "The Colorado Surface Coal Mining Reclamation Act" (The State Act), in 1979. This Act provided for the creation of a state regulatory program as accommodated within Public Law 95-87, "The Surface Mining Control and Reclamation Act of 1977" (SMCRA). Section 34-33-121(2)(a) of the Colorado Revised Statutes (CRS) and Section 516(b) of Public Law 95-87, identically require the underground coal mine operator to "Adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mined stability, and maintain the value and reasonably foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." On July 23, 1980, the Colorado Mined Land Reclamation Board adopted regulations to administer and enforce the State Act. Amendments to the Rules, including the subsidence regulations were adopted by the Board in August of 1981. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence.

Jan 1, 1985

By B. Hearn, O&apos

Falconbridge, Ltd. operates six mines (the strathcona, Fraser, Lockerby, Onaping, East and Kidd Creek) in the Sudbury and Timmins districts of northern Ontario (Fig. 1). These mines vary in depth to approximately 1500m and experience a wide variety of ground conditions. Problems of greatest concern include rockbursting, backfill pillar stability, wall and pillar stability, and the use of cable anchors. A study was initiated approximately two years ago to identify how numerical models could aid in the examination and possible understanding or solution of these problems. This paper discusses the use of numerical models at Falconbridge and describes a case history of their use in examination of rockbursting at the Strathcona Mine.

Jan 1, 1988

By G. Hwang, S. Park, H. Kim, J. Choi, P. Seo

"In the mineral processing, clay minerals have negative effects on the flotation of valuable minerals. In this study, we investigated how the floatability of malachite (CuCO3·Cu(OH)2) is affected by presence of the clay minerals in the fundamental aspects. Flotation experiments were conducted by using Na2S and PAX (potassium amyl xanthate), and the floatability of malachite was compared between the cases in the presence and absence of clay minerals. The results showed that floatability was greater in the absence of clay minerals than in the presence of clay minerals and decreased with increasing weight percent of kaolinite under same conditions applied. In addition to examine how clay minerals affect malachite floatability, we conducted flotation experiment with changing clay adding order. The results indeed showed that malachite floatability was affected by clay adding sequence. INTRODUCTION The demand of copper is growing as industrial development increases, but mineral resources are limited. Therefore, studies for Cu oxide flotation are being conducted to improve their recovery(1-3). However the mining industry is well aware of the difficulty in treating copper ores in the presence of clay minerals(4). Clay minerals have unique properties and these properties may affect flotation. In the previous studies, the effect of slime coating of clay minerals on flotation was investigated(4-6). For example, Zhao and Peng (2014), Peng and Zhao (2015), and Arnold and Aplan (1986) found that clay slime coating on chalcopyrite, chalcocite and coal surfaces through the electrostatic attraction reduced surface hydrophobicity and then depressed the flotation. Other researchers have also reported clay minerals have impact on pulp rheology. Especially in the case of bentonite, pulp viscosity increased with increasing amount of bentonite and the higher pulp viscosity have deleterious effect on copper recovery(7, 8). However, these studies only focus on slime coatings and pulp rheological behavior. Forbes et al. attempted to decoupling rheology and slime coatings effect on flotation but this study has limitation that individual role of two clay species either attached to mineral or suspended in bulk solution was excluded(9). Hence, in this study, we aimed to investigating the effects of individual clay (suspended and attached) on malachite flotation."

Jan 1, 2016

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Ertugrul Kaya, Kagan Ozdemir

The results of bench blasting on quarries, have important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc., and the total costs of that mine. Drilling and blasting is an important step in mine producing chain and its results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. Within the scope of this study, the three different hydraulic excavators’ working performances have been studied considering the particle size distribution after bench lasting at a quarry in Istanbul Turkey. Five shots have been realized on the quarry and average particle size of muckpile after each shot were assessed by digital image analysis method. Bucket loading times have been measured by stopwatch study after five shots. Excavator bucket loading times were also estimated by bucket loading time estimation formula which was published in ISEE 2007 Conference, Ozdemir et al. 2007. Estimated and measured times have been statistically analyzed and the accuracy rate of formula has been determined for five events.

Jan 1, 2008

By Victor Phillips

The Humphrey Preparation Plant of Christopher Coal Company, located in Monongalia County, West Virginia, was built to process the combined production of the Pursglove No. 15 and the Humphrey No. 7 Mines. Both Mines operate in the Pittsburgh Seam, primarily producing Metallurgical Fuel destined for by-product ovens in the Pittsburgh District. The results of an extensive core-drilling program have established sufficient reserves of low-sulfur coal to justify a 20,000 ton-per-day preparation plant, This is the story of the preparation phase of this combined operation. Christopher Coal Company operated the Pursglove No. 15 Mine to produce steam coal, which was prepared in a conven-

Jan 1, 1958

By W. H. Tomlinson

One of the more important functions of the Federal Bureau of Mines is conservation of the life and health of employees of the mineral and allied industries. Since its very beginning the Bureau has encouraged competition between mine rescue and first-aid teams as a means of stimulating interest in safety and accident-prevention work. In addition to sponsoring competition on a national and international scale during the past 45 years, the Bureau has also assisted State mining departments, mining companies, and mining organizations in holding State, district, company, and other local meets. This assistance includes providing instructors to train teams, judges, and other contest officials. The Bureau has also furnished problems and outlines for working them, judges I discount sheets (scorecards), contest rules, and problem judges. In fact, Bureau representatives participate in nearly all State, district, and company contests and have bad complete charge of some contests.

Jan 1, 1956

By H. S. Rankin, E. C. Houston

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By G. A. Johnson

Basic management principles will be discussed (as they apply to minerals education efforts), especially in light of the changing nature of volunteerism in today’s society. Also, the “minerals education tree” will be presented, along with public opinion / public policy realities.

Jan 1, 2001

By G. A. Reinhardt, H. J. Cutler

ThE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4-in. (14.5 cm.) square bloom to a 3/4-in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900" to 950' C. and cooling slowly in mica. The test bars were tempered by heating to 825' to 875" C., quenching in water, and drawing to 515" to 535" C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. UlTimate Strength.. Elongation, Lb. pER Sq. In. PEE Cent.. in 4 In. Not LeEs Than Annealed specimens.............. 78,230 to 92,450. 18 Tempered...................... 120,000 to 149,350 9 After experience on this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850" to 900" C. and cooling in still air; the annealing, in heating to 850" to 900" C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were: yield point, pounds per square inch minimum, 44,800; ultimate strength, pounds per square inch, 89,600 to 112,000; elongation, per cent. in 2 in. not less than 17. Difficulty was encountered as soon as work on this material was started. Many precautions and refinements were instituted but it was found very difficult to secure the required elongation.

Jan 1, 1920

The meeting of the Board of Directors, on November 22, was attended by eight directors, the Secretary of the Institute, and eight guests. The proposed James Douglas Prize and Tablet was referred to a committee of eleven. Robert H. Richards was appointed representative of this Institute to attend the meeting of the Society for the Promotion of Engineering Education. J. V. N. Dorr was made chairman of the Finance Committee in place of George D. Barron, resigned. The sum of $200 was appropriated for the 1918 expense of the American Engineering Standards Committee; the question of an appropriation for 1919 was referred to the Executive Committee for study and report. The sum of $50 was appropriated to the Treasurer's clerk. The following representatives of the Institute were elected: W. L. Saunders to succeed himself as United Engineering Society Trustee; R. M. Raymond to succeed himself as member of Engineering Foundation Board; S. J. Jennings to succeed himself as member of Engineering Council; George F. Kunz to succeed himself as member of Engineering Council; C. F. Rand to succeed himself as member of John Fritz Medal Board of Award; E. Gybbon Spilsbury to succeed himself as member of the Library Board. To members of the Canadian Mining Institute residing in Canada or Newfoundland, the privilege was extended to subscribe to the Bulletin at the price of $5. An invitation was extended to the Mining and Metallurgical Society of America to consolidate with the American Institute of Mining Engineers. The appointment of Engineering Societies' Employment Bureau was reported. Thirty-nine members and ten associates were elected. Two members were reinstated. Extension of time for the payment of clues was granted to four members. Seventeen members on active duty at the front had their dues remitted.

Jan 1, 1919

By Valentin R. Garfias, C. O. Isakson

The production of oil in Mexico during 1929 was approximately 45,000,000 bbl., or 5,000,000 bbl. less than in 1928. The production of the fields near Tampico showed a decline of over 10,000,000 bbl. for both the light and heavy crudes, which was partly offset by an increase of over 5,000,000 bbl. in the production of the fields in the Isthmus of Tehuantepec. During 1929 the retrenchment policy followed by practically all the companies was continued and no material improvement should be expected until the unsatisfactory conditions that brought about this situation are remedied. A new administration has just assumed control in Mexico; it should remain in power for 6 years, and the progress of the oil industry during that time will depend primarily on the policy pursued by the new government with respect to oil development. Development During 1929, there were drilled 214 wells as compared with 371 in 1928 and 583 in 1927. The percentage of producers in 1929 was 47.2 as against 34 per cent. in 1928. The new wells did not show water as quickly as in 1928, particularly in the Cacalilao field, where the greatest number of producers was brought in, their average initial daily production being 380 bbl. The flush daily production per well in the Southern fields was 1730 bbl., while the wells in the Isthmus of Tehuantepec came in with an average of 770 bbl. Development is summarized in Table 1. In the Southern fields 63 wells were drilled in 1929, of which 23 were producers, the best being drilled in Paso Real. This development tends to show that the southern extension of Dos Bocas-Alamo fault from Alamo to San Isidro terminates at San Isidro. The two wildcat wells completed in 1929, one in Magiscatzin and the other in Xicotencatl, were failures, and at the end of the year there were eight wildcat wells drilling and material was being hauled for two more.

Jan 1, 1930

By P. King

In considering the available reserves of coal, the author points to the importance of improved recovery, and defines three extraction ratios: the geological extraction ratio (or exploitation factor), the economic extraction ratio (or mining factor), and the geometrical extraction ratio (or volumetric extraction factor). He discusses the factors affecting each of these ratios, and concludes that, although geological factors cannot be considered in isolation from technical and economic factors, the geological extraction factor is the most significant criterion of whether the best use is being made of coal resources.

Jan 1, 1980

The radiolarian biostratigraphy of the western part of the Gympie Province, north of Brisbane, has been examined. This part of the province comprises mainly the Amamoor beds and the Gympie Group, which have been assigned Permian ages on the basis of localised marine macrofossils. This study has shown that the Amamoor beds and the Gympie Group include older strata than previously supposed.The Amamoor beds consist of at least two tectonic units, namely a melange unit (unit A) and a well stratified sequence of sedimentary rocks (unit B). The former unit, regarded as an accretionary subduction complex, contains chert blocks ranging from Late Devonian to Earliest Carboniferous, while the latter unit yields Permian radiolarians. Latest Devonian to Earliest Carboniferous bedded cherts occur in sequence previously mapped as Amamoor beds and Gympie Group.

Jan 1, 1990

By David M. Rempe

The purpose of this standard is to provide a method for testing of cushion materials that leads to uniform results when employed by various organizations and laboratories. The load-deflection characteristics measured using this method are intended to provide input data for analysis of pile driving, as in wave equation analysis of pile driving. It should be recognized, however, that there are several factors which may cause a difference in performance between the test samples under laboratory conditions and actual cushion materials under pile driving conditions. These factors include variations in material properties from sample to sample, compaction and/or deterioration of the materials with use, eccentric loading due to misalignment, confinement effects or the cushion container or inter layered materials, head buildup, rate of loading, etc. In order to obtain representative load-deflection characteristics, therefore, testing of cushion specimens which have been subjected to actual pile driving conditions is encouraged 1 such specimen should be tested at various stages of the useful life of the cushion. The users of the data are cautioned to determine if the particular wave equation program they are using requires either the secant or tangent definition of the stiffness and modulus of elasticity.

Dec 1, 1984

By Batric Pesic

Solvent extraction of nickel and cobalt from the real leach solutions was studied by using a novel extraction system. The extraction system was a mixture of 2,6-bis-[5-n-nonylpyrazol-3¬y]] pyridine (BNPP) and dinonylnaphthalene sulfonic acid (DNSSA). The BNPP represents a novel molecule, which was designed and synthesized in our laboratory. Real solutions for the study were prepared by leaching of two different cobalt-nickel bearing concentrates, cobaltite [CoAsS] concentrate from Blackbird Mine, Idaho, and siegenite [(Ni,Co)3S4] concentrate from Missouri Lead-Belt. The major strength of the system was the selectivity of extraction toward nickel and cobalt from iron containing solutions. Other metals such as Mn, Mg, Ca, Al and As were not extracted. Due to the irreversibility of copper extraction, its removal from solution was required prior to the extraction of nickel and cobalt. Zinc was not as strongly extracted (i.e. its stripping was readily achieved) as was copper . Flowsheets for the recovery of nickel and cobalt were also developed.

Jan 1, 1997