Search Documents

By Arthur F. Colombo, Donald W. Frommer

With the opening of the Tilden mine near Ishpeming, MI, a new era in iron ore beneficiation was begun. A description of a U. S. Bureau of Mines investigation is summarized to illustrate the selective flocculation-deslime-flotation process developed by the Bureau and used at the Tilden concentrator, which is also briefly described. The operating parameters for the selective flocculation-cationic flotation of an oxidized taconite from the Mesabi range are discussed. A water reclamation system using lime and a cationic flocculant was applied to reclaim the effluents from a 900-pound-per-hour flotation pilot plant. About 80 percent of water requirements were recovered, and the calcium content of the reclaimed water was found to be more important than clarity in influencing the selective flocculation and flotation processes. Although reclaimed waters with about 10 ppm calcium registered turbidities of approximately 5,000 ppm SiO2 equivalents, the concentrates produced using these waters contained 64 percent Fe and 55.0 percent SiO2 and had accompanying iron recoveries of 75 percent. Lower grade concentrates resulted from using reclaimed water with higher calcium contents and lower turbidities.

Jan 1, 1976

This paper describes the results of a laboratory study on the upgrading of Algoma siderite by the amine flotation of silica and silicate gangue. The experiments indicate that a virtually complete removal of silica is possible in a rougher flotation con-ducted in tap water at natural pH, without prior desliming of the ore. Grinding considerably finer than the apparent liberation size is essential for maximum silica rejection. A cationic collector, Aeromine 3037, gave best results when used in combination with a modifier. Of the several modifiers tested, a Dutch potato dextrin, Dextrin 4356, was found to be the most effective. Both iron recovery and the grade of the final iron product are enhanced by floating the pyrite contained in the ore prior to the amine flotation of the silica, and by scalping the magnetics from the silica concentrate. F OR over twenty years, the Algoma Ore Properties Division of The Algoma Steel

Jan 1, 1963

By W. C. Winegard, C. Elbaum, T. Ojala

NONOCTAHEDRAL slip was observed in poly- crystalline aggregates of aluminum by Boas and Ogilvie.&apos; These authors indicate that the non-octahedral slip takes place on (100) or (110) planes. Ogilvie2 studied the continuity of slip lines across grain boundaries in polycrystalline aluminum. Non-octahedral slip was observed by him, but it was not reported to occur in the continuous slip lines across the grain boundaries, which were identified as octahedral slip in all cases. The present note reports the observation of non-octahedral slip in the grain boundary region of an aluminum bicrystal and tricrystal, both deformed in tension at room temperature. An analysis is made, which leads to a probable identification of the non-octahedral slip planes as (110) and (331). The specimens used were of rectangular cross section, approximately 5x10x200 mm. They were prepared by growth from the melt, using aluminum reported by the manufacturer to be 99.994 pct pure. The grain boundaries were in a plane perpendicular to the wider face and parallel to the long dimension of the specimens. The axis of tension was also parallel to the long dimension of the specimen. The orientations of the specimens studied were determined by the Laue back-reflection method and are given in Fig. 1. The nonoctahedral slip was first observed after about 6 pct extension in the bicrystal, and after about 2 pct extension in the tricrystal. The micrograph, Fig. 2, of the grain boundary region of the bicrystal shows two active slip planes throughout each of the two crystals, with a third plane active at the grain boundary in each crystal. Two major sets of slip traces observed in grain No. 1 are consistent with the operation of the slip systems (ill) [oil] and (111) [011]. The nonoctahedral slip takes place on a plane belonging to a <111> zone, as determined by drawing trace normals. Assuming that slip will take place only in the <110> direction, the planes in the <111> zone, which do not contain that direction, need not be considered. Among the remaining prominent planes of that zone, the (011) plane has a common slip direction—the [011]—with the (111) plane, which acts as one of the octahedral slip planes. In grain No. 2, a similar situation to that in grain No. 1 is observed. As indicated previously, the (oil) plane in the <111> zone, to which the nonoctahedral slip plane belongs, has a common [Oil] slip direction with the acting (ill) slip plane. Also, the orientation of the (oil) plane in grain No. 2 almost coincides with the orientation of the acting (111) slip plane in grain No. 1. Similarly, the orientation of the (oil) plane in grain No. 1 almost coincides with the orientation of the acting (111) slip plane in grain No. 2. It is, therefore, possible that the nonoctahedral slip was induced, in both cases, by octahedral slip in the neighboring grain. It is important

Jan 1, 1957

The Canadian Mining Institute has accepted the proffered arrangement as to price of the Bulletin to members and will furnish its Bulletin to members of the A. I. M. E. at $1 per year.

Jan 5, 1919

By R. Hiebert, M. Canty, S. Beckman

An innovative biological process is described for the treatment of cyanide-, metals- and nitrate-contaminated mine process water. The technology was tested for its ability to detoxify cyanide and nitrate and to immobilize metals in wastewater from agitation cyanide leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to demonstrate the technology on a mine process-waste stream at a mine in Nevada. The demonstration was performed jointly under the Mine Waste Technology Program (MWTP), funded by the US Environmental Protection Agency (EPA) and jointly administered by the US De¬partment of Energy&apos;s (DOE) Western Environmental Technology Office (WETO) under Interagency Agree¬ment Number DW89938513-01-0. The Superfund Innovative Technology Evaluation (SITE) demonstration program was also involved in the project. MSE Technology Applications Inc. (MSE), Butte, MT, was the contractor responsible for conducting the project, and Pintail Systems Inc., Aurora, CO, was the technology provider. The pilot-scale unit was field-tested at Echo Bay&apos;s McCoy/Cove Mine southwest of Battle Mountain, NV. The biotreatment process was considered successful in destroying cyanide in the mine process water. The process was also determined to be effective in removing metals. The pH was consistently neutralized and nitrates were successfully removed from the mine process water. From the results of these pilot-scale tests, it was concluded that the biotreatment process potentially of¬fers an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 2000

By P. H. Mutschler

The Bureau of Mines studied the costs of transporting fossil fuels, coal, and residual fuel oil from areas of production to consumer regions. Transportation data were stratified by type of carrier, size of shipment, and distance to determine what general effects these variables have upon transportation costs. Economics of haul for coal exist for longer versus shorter distances, and for larger versus smaller trainload sizes. Tanker and barge transportation of residual fuel oil does not show economies of haul for longer distances. It is shown that tanker size and seasonal variation are primary factors influencing the cost of shipping. Railroad transportation data show that coal from western coalfields could be competitive with foreign residual fuel oil in selected midwestern fossil fuel markets. However, the western coal would not be competitive in the New England and the eastern seaboard energy markets.

Jan 1, 1973

By Frank L. Nason

During the months of June and July of the present year, the writer made a special geological survey of the mining property of Messrs. Cooper and Hewitt, at Ringwood, New Jersey. Some of the results of this survey are presented to the society through the courtesy of Hon. Abram 8. Hewitt.

Jan 1, 1895

By John R. McWilliams

This report is one of a series published by the Bureau of Mines describing methods and practices at various mines throughout the United States. A previous program, conducted from 1928 to 1939, was well received by the mining industry and technical institutions and provided much source material for engineering textbooks and technical handbooks. The stringent wartime demands on the mining industry, the rapidly changing postwar economic situation, and greatly accelerated technologic growth have combined to render many of the previous data obsolete. The objective of the present program is to assemble reliable technical information on mining methods and practices throughout the country and present it for the use of the mining industry, technical schools, textbook authors, and other interested persons. This report deals with the design and development of the Berkeley open- pit mine at Butte, Mont., owned and operated by The Anaconda Company. The Berkeley pit is but one facet of a well-organized and integrated copper-mining operation involving the entire Butte district. Vein-type mining, important for 75 years, is still in progress at depths from 600 feet to nearly 1 mile; on intermediate levels, low-grade ore left untouched by earlier vein-type mines is being extracted by block caving entire ore zones,3/ and secondarily enriched but lower grade near-surface portions of the same ore zones are being mined by open-pit operations (fig. 1). The Berkeley pit itself is named for the Berkeley mine, one of the old mines that extracted copper ore from high-grade veins in the area that now will be mined by open-pit methods.

Jan 1, 1959

By Antonio Laguna

During the past few years, synthetic efforts have been addressed to the synthesis of polymeric materials with optical or semiconducting properties or even with capabilities to act as sensors for volatile organic compounds (1). The most recent studies have been concerned with the synthesis of heterometallic systems with short metal-metal interactions and the determination of their optical properties. These complexes are undoubtly interesting from a theoretical viewpoint and include an emerging class of luminescent materials, in which the observed luminescence results mainly from the interactions among the different metal centers, as well as the environments of these atoms. The understanding of the photophysics and photochemistry of these products could permit the design of complexes with appropriate metals and ligands chosen for individual applications. Following a synthetic strategy consisting on reactions between acid heterometal complexes and basic gold precursors we have succeded in synthesizing supramolecular assemblies formed via acid-base stacking, which display tunable luminescence or selective and reversible sensitivity to Vapour Organic Compounds (VOC?s) (2-5). In this sense, in accord with previous Mössbauer studies carried out in the gold precursor complex [AuR2]- (R = C6F5), the basic properties of this and related materials have been employed as building blocks of supramolecular assemblies in their reactions with complexes in wich the metallic centers act as lewis acids as, for instance, Tl(I) or Ag(I) (6). For instance, in the case of silver, by reacting equimolecular quantities of [NBu4][Au(C6F5)2] with AgClO4, in acetone, a solid of stoichiometry [Au2Ag2(C6F5)4(OCMe2)2]n is obtained. The polymeric nature of this material in solid state is confirmed through X-ray analyses (figure 1). It consists of polymeric chains formed by repetition of Au2Ag2 moieties linked through short gold-gold interactions. Nevertheless, in solution, the nature of this polymeric materials was still a matter of controversy and, in this case, the optical properties have been shown as useful tools in order to obtain information. Thus, while dilute acetone solutions of this complex give a emission coming from pentafluorphenyl localized ??* excited states, in accord with the presence of isolated tetranuclear Au2Ag2 units, when the measurements are done at different and higher concentrations, a band that does not obey the Lambert-Beer law appears. This deviation is consistent with molecular aggregation in solution of these units through gold-gold interactions, and a clear correlation between the emssion wavelength and the structure in the solid state and in solution is shown (figure 2). DFT calculations accord with the observed experimental behaviour and show the nature of the orbitals involved in each transition.

Oct 1, 2003

By Duke J. H

Advanced computer aided geological modelling techniques are now available to the geologist to allow the rapid evaluation of a gold orebody at various stages of its development. The types of grade estimation techniques used change during the various stages as the density of drilling and knowledge of the deposit increases. At the prospect evaluation stage drillhole intercept selection techniques are coupled with preliminary 2D (vein or layer) modelling or 3D block modelling techniques to arrive at a geological resource estimate. At the prefeasibility and feasibility stages more sophisticated 2D and 3D modelling techniques, such as domain controlled grade interpolation with anisotropy, are used along with interactive open pit and underground mine design, to calculate recoverable reserves. At the production stage closely spaced blasthole sample data is modelled quickly and coupled with interactive grade control facilities. Shot volumes, tonnages and grade estimates can be databased to provide reconciliation figures. These modelling techniques are embodied in MINEX-3D, an Australian software system which, with the emergence of the 386-based PC and high resolution (VGA or better) graphics, makes a whole range of advanced geological modelling techniques available to most exploration and mine geologists.

Jan 1, 1989

By R. R. Brown

The solubility and the activity of aluminum chloride hexahydrate, A1C13?6H2O, in aqueous solutions were determined as a part of the Bureau of Mines, U.S. Department of the Interior, research to improve mineral processing technology for recovering alumina from low-grade domestic resources. The solubility of A1C13 in pure water was found to be 31.09 and 31.77 wt-pct at 25° and 85° C, respectively, and decreased drastically to 10 and 0.1 wt-pct when the respective amounts of 20.3 and 37 wt-pct hydrochloric acid (HCI) were added in solution. The equilibrium constant for the solubility of hexahydrate, activities, and activity coefficients of A1C13 and H2O were calculated and compared with the results from the available methods of estimation. The results were shown to be useful in leaching nonbauxitic ores for extraction of alumina by changing the solubilities of component salts upon addition of HC1. Simultaneous solubilities of A1C13, FeC13, KC1, and NaC1 in solutions of HC1-H2O were also determined and their effects on the purity of A1C13?6H20 crystallized from mixed salt solutions are briefly discussed.

Jan 1, 1979

By W. C. McClain

The amount of vertical subsidence occurring over a longwall operation is a function of the thickness of material removed, the quantity and quality of any fill material, the width of the extraction, and the depth. The relationship between these variables is empirically determined, and subsidence can be predicted using only a few easily established constants which are subject to local conditions, such as the angle of draw. Associated with the vertical subsidence are both tensional and compressional horizontal strains. The component of strain in the direction of face advance is temporary, while the component perpendicular to the direction of working is permanently retained by the ground. It is these horizontal strains and the vertical strain (tilt) which result in damage to surface structures. It is possible to ameliorate the consequences of mining subsidence by utilizing the well-proved techniques described in this paper in the underground operations and on the surface. INTRODUCTION In the past, American mining practice in stratified deposits has been mostly restricted to production by the room-and-pillar system where a sizable percentage of the salable product is left in place as pillars. These pillars are usually regularly spaced and provide a permanent support for the roof of the mine and the surface above. The longwall system employs an advancing face which may be as much as several hundred yards long and some sort of breaking and loading machine which moves back and forth along the length of the face. The roof is supported behind the face only to a distance required to provide working space for the production machine. The supports are then withdrawn and the roof is allowed to cave. The longwall system therefore possesses the various advantages of complete extraction, thus effectively increasing reserves, while at the same time eliminating the necessity and cost of installing artificial supports such as roof bolts and heavy steel girders over large areas. Longwall mining has long been practiced in Europe, where it has undergone an involved development, culminating in the recent perfection of powered-loading machines and automatic self-propelled supports, offering high productivity. With ever-in creasing

Jan 1, 1967

Advanced high temperature electrochemical systems such as fuel cells, electrolyzers and ionic transport membranes are currently being developed for a wide variety of energy conversion, storage and gas cleanup applications. These systems offer high electrical efficiency, multi fuel capability, modular construction, no/negligible emissions (SOx, NOx, VOC, particulate matters) with capability to sequester green house gas emissions (GHG). Electrochemical processes and electrode reactions will be discussed. Cell and stack component materials and fabrication processes will be presented. Bulk, surface and interface degradation processes responsible for cell and stack performance degradation will be examined.

Jan 1, 2005

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey&apos;s results to characterize the U.S. stone mining workforce from March through September 1986. Similar reports have been published for the metallic, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

Ore reserve estimates form a basis for strategic mine planning at Argyle Diamonds open pit and alluvial operations. Most ore reserve statements are mainly concerned with resource tonnage and grade. Because diamond deposits are low grade, high value resources, diamond quality ($/carat) is also an important parameter. Relatively large variations in quality and/or grade can occur. These variations must be taken into account before the resource potential can be fully assessed. Computers (HP9000 and PC&apos;s) are utilised to compile resource inventories. Resource inventories are then ranked on an economic basis. This paper discusses the methods used to compile resource inventories and explains how these are then used to present ore reserve estimates in terms of resource potential.

Jan 1, 1990

By D. Seo, P. Au, S. Yandt, N. Tsuno, A. Sato

Nickel-base single-crystal superalloys are used for gas turbine airfoil applications due to their excellent high temperature properties. A good understanding of the mechanical response of these alloys under different temperature and loading conditions is essential for modeling their behavior. In this study, the low cycle fatigue behavior of CMSX 2 oriented with the loading axis along [001] was investigated under zero-compression strain-controlled loading at 1100°C. The experiments were performed with or without a two-minute dwell (hold) in compression. The microstructure before and after testing was analyzed to understand the deformation characteristics including the effect of dwell.

Jan 1, 2010

By Alexandru Corneliu Stematiu, Catalin Popescu, Radu Sarghiuta

"The tunnel sector is excavated into a rock mass heavily affected by tectonics, defined as a regional fault. The rock around the tunnel support undertakes the non – elastic deformation and gradually detaches from the rest of the non affected rock mass, moving inside of the excavated area and tending to fill up the whole space. The initial solution of using stiff support consisting in double steel ribs I12 with circular shape in the upper part and straight vertical pillars in the lower part has proved to be inadequate. Based on the calculations of the subsidence phenomena and a mathematical model, the proposed alternative support was provided by special circular steel ribs – SG-23 –that allows a limited rib deformation (by relative slip between the arch segments) in order to mobilize the contact between the rock contour and the inner face of the rib - not only for the deformed rib but also for the neighboring ribs. 1. INTRODUCTION Hydropower development of Jiu river in Romania, in the narrow gorge sector includes two diversion HPP and a small hydro plant that provides the minimum required flow downstream: CHE Dumitra , CHE Bumbesti and MHC Livezeni (Table 1. Hydropower parameters).The Livezeni intake reservoir is provided by a gated dam located 1250 m downstream of merging point between Jiul de Vest river and Jiul de Est river. The dam is equipped with three radial gates with flap gates with a span of 12 m each and the height of (6 + 3) m. The longitudinal profile of Dumitra head and the location of the gallery zone that is the subject of the paper are presented in Figure 2. Longitudinal Profile – Dumitra Head."

Jan 1, 2016

By R. G. B. Pickering

The purpose of this report is to chronicle the interaction between Anglo Platinum and Sandvik Tamrock during the development and application of Long Hole drilling as a viable, practical method of narrow reef mining. Appendix I identifies the people from Anglo Platinum and Sandvik Tamrock who participated in the project. Experiments in long hole drilling and blasting were conducted in a number of mines during the late 1950s and early 1960s. Some of the advantages envisaged were: ? The face would require no daily examination ? No barring down or immediate face support required ? No sockets to clean ? Only a few well drilled holes rather than large numbers of short blast holes ? Avoidance of poorly-marked holes, inaccurate drilling and improper charging ? Better supervision and better face advance. Holes 50 mm in diameter were drilled parallel to the stope face by pneumatic rock drills from advance strike gullies. Holes were charged with amon gelignite cartridges. All holes were traced with detonating cord to ensure propagation of the explosive along the entire hole length. Rock was blasted onto a rolling scatter pile. A number of reasons have been cited for the failure of this mining method. The two most important were: ? problems in controlling hole deviation which was exacerbated by the fractured ground ? difficulty of charging up holes in fractured ground, due to relative movement of rocks along fracture surfaces over the hole length. The idea of drilling a few long holes parallel to the face rather than a large number of short blast holes perpendicular to the face was an attractive option to mechanize narrow reef mining. This particular project started in 1998. Initial trial The Union Section of Anglo Platinum purchased a Solo H 606 RA long hole drilling rig from Sandvik Tamrock in 1997. In order to evaluate long hole drilling as a basis for face mechanization. The Solo series of drill rig was selected because it combines high drilling performance and good drilling accuracy with high versatility with a compact size. The mining method proposed by a consultant to Anglo Platinum was based on the current trackless mining method practised by Union Section. The trackless mining method is better described as a trackless development and transport method. Reef strike drives were installed approximately 40 metres apart on dip using trackless equipment. Reef was mined using hand-held pneumatic rock drills and scraper winches and the excavation was supported by sticks and crush pillars at the top of the panel. Rock scraped from the panel was loaded by Lad Haul Dumps (LHDs), trammed to an inclined haulage, and loaded into trucks for transport to the surface. It was intended that the Solo would drill from the bottom advance strike drive to the top advance strike drive. Blasted rock would still have to be scraped from the panel. It is also difficult to understand how well the support would have survived. In the initial motivation it was stated that drilling accuracy was of the utmost importance. Previous work by Sandvik Tamrock had shown that, in other parts of the world, 20 metre long holes could be drilled with a deviation not exceeding 100 mm provided that: ? holes were collared with low thrust pressure ? operating percussion pressure was kept low -often not ? exceeding 10 MPa ? drilling was to be with tubes, not rods. In early 1998 initial trials with the Solo H 606 RA were inconclusive; attempts were made to drill 40 metre long holes from one advance strike drive to another. Difficulty was experienced in measuring hole straightness and accuracy, there was no survey of the holes, and no blasting was done to expose hole barrels. A long hole mining system was then defined, with a corresponding face mining system, which led to the design of a test programme for the Solo drilling rig. Earlier experience at Telfer The proposed face mining system was based on a mining method that is practised at Telfer Gold Mine in Western Australia. Telfer has a series of domed reefs that dip at angles of less than 20° to more than 40°. The ore bodies are all thin, with widths from 0.6 metres to 0.8 metres. Figure 1 shows the face layout. Experience at Telfer indicated the following: ? The spacing and size of the dip pillars should be based on the rock mechanics of Union Section ? The length of the face is determined by the ability to correctly position the blast holes. Positioning of blast holes is a function of hole straightness and hole direction. Blast holes in Telfer were drilled 64 mm diameter with retrac bits from Sandvik. Extension steel was T38 by 1.8 metre lengths. A guide rod was fitted immediately behind the bit. To achieve greater accuracy&apos; operators drill at relatively low percussion and thrust pressures. Results show that very good accuracy is achieved in 20 metre stopes and only fair accuracy in longer stopes. In 34 metre long stopes 10-15% of the holes are not sufficiently accurately positioned and have to be re-drilled. All blast holes are

Jan 1, 2006

By Subhash C. Malhotra

This paper discusses the historical background on major sources of obsolete electronic scrap and spent catalytic converter scrap. The paper discusses the principal changes taking place that will affect the future supply of these scraps. The author projects from this background the future opportunities for reclaimers and refiners in these two important segments of the precious metals scrap reclamation industry.

Jan 1, 1984

Develop a method for recovering phosphate from a wide variety of complex western phosphate materials, including low-grade ores, tailings, and unused fines. Approach A flotation technique is used for this broad type of extraction. The method includes depression of phosphate minerals and anionic flotation of carbonate minerals, followed by cationic flotation of silicate minerals. How It Works A slurry is prepared for flotation by sizing to remove a low-grade, high-impurity slime fraction. Depending on the material, further sizing and/or grinding steps may be used to produce a size concentrate or to remove gangue. The flotation feed is conditioned with H2SiF6 and a fatty acid emulsion. The H2SiF6 is absorbed chemically to the phosphate mineral surface, making it strongly attracted to water and preventing adsorption of the fatty acid. Under these conditions, the fatty acid is a selective collector for carbonate minerals, which are removed as a froth product. Next, the silicates are floated with an amine reagent added directly to the slurry without additional pulp preparation.

Jan 1, 1982