Search Documents

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

The Cadia Mine is located 25kms South West of Orange in the central west of New South Wales (NSW), Australia (Figure 1). Orange is a major regional centre with a population of 35,000 people. Cadia has a history of mining and exploration dating back to 1851 and shortly after the first Australian gold rush at Ophir, north of Orange. Newcrest Mining commenced an exploration program at Cadia Hill in 1992. This identified a substantial zone of copper and gold mineralization. Subsequent resource definition drilling defined an orebody with a mineable reserve of 200 million tonnes of ore with an average gold grade of 0.74g/t and 0.17\ copper. A full feasibility study commenced in 1994, approvals to proceed with development were granted in September 1996 and the processing plant was commissioned in July 1998. The project came in on budget at A$440 million and on time, 24 months from design to construction. The estimated operating cost at the time of commissioning was A$8.85/t of mill feed.

Jan 1, 1999

By D. E. Thomas

Oxidation rate constants were determined for Cu-Pd and Cu-Pt alloys as a function of alloy composition and temperature. Reaction products were identified. Relationship between oxidation rate constants and diffusion constants in the reaction zones is discussed. THE mechanism of oxidation of alloys is consider--'¦ ably more complex and not so well understood as that of pure metals. The oxidation of a one-phase binary alloy of which one component is a noble metal should logically be the simplest case of alloy oxidation, for in this case one is concerned presumably only with the oxidation of the base metal and the diffusion process by which it reaches the reaction site. This had led a number of investigators to study such systems. Probably the earliest work was that of Tammann and Rienacker' on the tarnishing of Cu-Au alloys at temperatures up to 300°C. These alloys oxidize according to the logarithmic law, that is, the film thickness is proportional to the logarithm of the time. The rate of film formation was found to decrease with increasing gold content. Raub and Engel² investigated the oxidation of Au-Cu, Cu-Pd, Au-Ag-Cu, Au-Pd-Cu, and Ag-Pd-Cu alloys at 750°C in air. These alloy systems form a continuous series of solid solutions at the temperature of oxidation with the exception of those containing silver. Au-Cu alloys oxidize parabolically, the rate constant decreasing slowly with increasing gold content up to about 15 atomic pct* Au, and more rapidly thereafter. An alloy with 14 pct Cu forms only a very thin layer of CuO on the surface and probably also a subscale.† Alloys containing more than 14 pct Cu have scales consisting of CuO and subscales of Cu,O embedded in nearly pure gold. The Cu-Pd alloys obey the parabolic law except for slight deviations for alloys containing 53 and 84 pct Cu. The overall oxidation rate decreases rather smoothly with increasing palladium content. A scale consisting of a thin layer of CuO and a thick layer of Cu²O and a subscale of Cu²O embedded in nearly pure palladium was observed for alloys containing 84, 53, and 30 pct Cu. An alloy with 19 pct Cu formed only a subscale of CuO embedded in nearly pure palladium, and an 8 pct Cu alloy formed only a thin film which was presumed to be PdO. The ternary alloys considered by Raub and Engel oxidized in much the same way as did the binaries. Wagner and Grunewald³ found that Ni-Au alloys, oxidized at 900°C in oxygen, formed a scale of NiO and a subscale containing NiO and gold. The overall oxidation rate increases with increasing gold content, passes through a maximum and then decreases to zero for pure gold. The fact that gold increases the oxidation rate was attributed to "pores" in the scale. Kubaschewski' investigated the air oxidation of alloys of platinum or gold with up to 10 pct Cu or Ni at temperatures in the range 300" to 1550°C. Parabolic behavior was noted for all alloys except Au-Ni, with rates decreasing in the order Au-Cu, Au-Ni, Pt-Ni, Pt-Cu. The diffusion coefficients for the latter three systems are known, and they decrease in the same order. However, activation energies for the oxidation of these alloys do not agree with the activation energies for diffusion in the respective alloy systems. Kubaschewski and Goldbeck7 nvestigated the oxidation of Ni-Pt alloys in air at temperatures of 600"

Jan 1, 1952

By Ludwig Strah

"The paper outlines the history of rubber mill liners beginning with the awarding of the first North American patent rights in 1923. It includes the early-day applications and installations of the 1920s and 1930s through to their present-day application. Over-all rubber mill liner design is discussed in relation to present day installations employing rubber mill liners in various grinding applications. A brief overview is given of a manufacturer's procedures to produce rubber mill liners.IntroductionIn early 1910, it became apparent that the productive life of the silver mines in Cobalt, Ontario, could be substantially prolonged by mining lower-grade ores.The mining of lower-grade ores required the establishment of treatment facilities which initially employed jaw crushers, stamp mills, jigs and concentrating tables. The recovery of silver in other than a coarse metallic form required the additional step which was introduced at that time: the cyanidation of silver concentrates from the tables. The resultant requirement for increased and improved recovery led to the introduction of grinding mills, i.e. tube mills.Shortly after the introduction of the tube mills to the Nipissing Mine's mill in 1914, the idea of using rubber as a mill liner material was spawned. However, no action was taken due to the advent of World War I. It is interesting to note that the idea of rubber mill liners emanated from having used pieces of solid rubber tire as an emergency repair on a set of liners when a liner had broken and no immediately available spare was on site.The credit for this ingenuity and subsequent application for a patent on rubber mill liners falls to James John Denny, the mill superintendent, and Rolla Barnum Watson, the general manager of Coniagas Mines Limited. The patent application was formally made on December 3, 1921. The U.S. Patent Office issued Patent No. 1,470,597 on October 16, 1923."

Jan 1, 1982

By Peter Kovalchik, Ed Kwait, T. Michael Durr

1. BACKGROUND Many research projects on engineering controls for noise reduction in mining were conducted by the former U.S. Bureau of Mines, mostly under contracts from 1972 through 1986.1 Contracts were awarded to determine which mining equipment was responsible for worker noise exposure over the permitted Federal Regulation level of 90 dBA for 8 hours. Dominate noise sources, for each piece of equipment was also determined. The final goal was to develop engineering noise controls for those pieces of equipment and then evaluate them. This was the general approach taken in each research project or contract. This paper deals with what is known about the control of noise from continuous miners, one of the most commonly used underground mining machines. A literature review on continuous miners revealed that the relevant noise sources were divided into four categories: conveyor, cutting head, drive train, and motor noise. The dominate noise sources reported were the conveyor noise and the cutting noise.2 Conveyor noise consists of impacts and scraping at various locations on the conveyor structure. These impacts are associated with discontinuities on the top and bottom decks, impacts between the chain and the tail roller, impacts on the sidewalls at path points of discontinuity under horizontal pivot, and impacts on the flex plate.3 Scraping occurs along the entire length of the chain conveyor. The other dominate source, the cutting of coal, has also been addressed in past research.4, 5, 6 The research presented in this paper only addresses the controls associated with the conveyor. The literature suggests several effective treatments for noise control: retrofitting the chain conveyor with a urethane coating or a urethane sleeve on the chain flights, using a urethane coating or urethane sleeve on the tail roller, constrained layer damping of the decks, and the use of a modified take up plate.7, 8 However, the in-mine durability of these concepts has yet to be proven for the conveyor system. This paper analyzes extensive noise and urethane durability testing on a Joy 14CM9 continuous miner’s conveyor assembly, tail roller, and bottom plate conducted at the Pittsburgh Research Lab facilities. It will also discuss the initial underground testing results for the urethane-coated conveyor flights and tail roller.

By D Genge, E Martin, T Goswami, M Rothery

Rio Tinto’s Hunter Valley Operations is a large open pit coalmine situated in the heart of the Hunter Valley in Australia. The Riverview West Pit has faced increasing production challenges in recent times due to decreasing dragline strike lengths and increasing environmental constraints on vibration, overpressure and fume generation. Conventional mining techniques would involve five to six production blasts per strip to recover multiple coal seams. Each blast event carries the risk of exceeding the strict environmental requirements. By working collaboratively with Orica, it was realised that the blasting method known as Stratablast™, in conjunction with advanced computer modelling techniques, could provide productivity gains whilst simultaneously providing more control over the environmental effects and the impact on nearby infrastructure.As a result of this change, the number of blasts per strip was reduced to one, with the implication that a great deal of care and forethought was needed to manage the increased challenge posed by multiple constraints in the proposed mining area. This innovative approach of combining throw and stand-up blasts allowed the extraction of all major coal seams in a single pass blast event. The blasts were initially designed with a large factor of safety to stay within environmental limits as they were over 1.1 km in strike length, with more than 800 holes and with a total charge weight of about 1000 t of bulk explosives. Furthermore, there were conflicting priorities around the desired blast outcomes. So far, 11 such blasts have been designed and successfully fired. After each blast, innovative design changes have been iteratively implemented to provide further control over environmental impacts, whilst continuing to improve productivity. As a result of these changes, blasts have progressively increased in complexity with the inclusion of features such as damage zones, mid-splitting, time gaps and different directions of firing. The consequence of this complexity is that the blast duration can be as long as 28 seconds to accommodate all components of the blast.This project has increased the productivity of the Riverview West Pit through blast design improvements and allowed the environmental impacts to be managed with far more control and predictability than would have been possible under a conventional blasting regime. There still remains room for further optimisation of mine productivity and this is being addressed through a process of continuous improvement.CITATION:Goswami, T, Martin, E, Rothery, M and Genge, D, 2015. A holistic approach to managing blast outcomes, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 645–654 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The modern theory of sampling of particulate minerals essentially consists of a recent generalization of the procedures for applying and calibrating the formula usually known as ?Gy?s Formula? for sampling variance control, in which the central concept is a parameter called the liberation factor l. A model which can be experimentally adjusted was proposed by one of the authors several years ago, based on geostatistical considerations. This new model, which relates the liberation factor to the sizes of the fragments and mineral grains, solves the usual difficulties faced in the past, and permits predictions that are well verified in practice. Unfortunately, an older, arbitrary and less general formula is still widely used. The vast majority of today?s misapplications of Sampling Theory of Particulate Materials can be traced back to the use of this antiquated and generally incorrect model. Following a brief history of the models used for the liberation factor and a description of its main variable, the liberation size, and to illustrate the importance of proper modelling of l, this paper presents demonstrative calculations of the absurdity of the incorrect model using the particular case of gold mineralization as an example, followed by some more positive examples of application.

Jan 1, 2002

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By Howard K. Worner

Several features of smelting and refining operations make them appropriate technology to adapt to the processing of "wastes" not only from the minerals Industry itself, but for wastes in general. These features include significantly higher temperatures than are achieved in conventional Incinerators and also good thermal stability derived from the mass of molten metal and slag in the furnace. This paper expands on Information contributed to the Mervyn Willis Symposium in July 1992 and includes knowledge generated in the last two years of waste processing R&D in a sealed 100kg capacity DC arc furnace specially constructed for the "Environment" process being developed in Wollongong. As one product of-the process is a foundry-type iron, the feed always contained ferruginous dusts or heavily contaminated scrap. For the dusts, sewage sludge has been used as a binder and also as a proportion of the fuel-reductant. To achieve the necessary bath carburisation, It is beneficial to add other lower reactivity carbons such as "kish' graphite, carbon from electrode butts, dusts from coke ovens, carbon from aluminium pot line residues, dry cell batteries etc. Metallurgical factors involved In process control, Including metal and slag, compositions, are discussed.

Jan 1, 1994

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

By Fourney W. L, Dick R. D

Tests were conducted in plexiglass and Rockite models to determine if crater blasting could be improved by changes in charge geometry or by alterations to the borehole. Circumferential grooves were placed at various locations in the borehole in an attempt to control the initiation site of the crater. Grooves located at or above the top of the cylindrical charge had no effect on the resulting crater. Grooves placed too low in the borehole were successful in controlling the initiation site but the growth of the fracture system was not sufficient to reach the upper surface. Grooves located at a height of two thirds of the charge length were quite successful in that resulting craters were bigger by at least a factor of six than the normal crater. Testing was conducted in Rockite models to investigate charge geometry. Spherical charges in ungrooved boreholes resulted in crater sizes that were three times larger than those caused by cylindrical charges.

Jan 1, 1990

The Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and out¬standing attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors

Jan 1, 1939

By D. W. Hendrickson

Cleveland-Cliffs views the mining process as ex- tending from mine planning to cargo loading including auxiliary systems such as materials handling and plant utilities. Process automation is recognized as an area that can provide significant improvement opportunities with less capital requirement than major flowsheet modifications. This article discusses the development and results of a strategy to allow and promote implementation of process-automation improvements at individual mines based on their economic priorities, taking advantage of common systems and concepts for use at multiple mines where practical. Specific process-control upgrade projects at Hibbing Taconite Co. and the Empire Mine are reviewed.

Jan 1, 1998

By Vernon R. Degner

The past two decades has seen the application of the mechanical flotation machine, originally developed primarily for metal1iferous ore beneficiation, increasingly applied to cleaning coal in the 28x0 T. Mesh size range. Internal cell hydrodynamic studies of mechanical flotation machines of all sizes, as well as computer aided modeling studies of flotation kinetics has, within the last five years, established a basis for optimizing coal flotation circuit design and machine operation, and has a1 so pointed a way toward improvements in mechanical flotation machine design for the future. Consideration of the trend toward increased fines produced by current mining techniques, as well as the environmental need for a progressively cleaner product, lends support to basing the design of the mechanical coal flotation machine of the future on finer feed; below 100 microns in size. Future types of mechanical flotation machines, which may satisfy the fine coal cleaning requirements for a significant improvement in product grade while maintaining the combustible recovery levels of current technology, are discussed.

Jan 1, 1988

By H. R. Gardner

THE wide variation in tension and compression properties' which exist between the a,ß and ? phases of plutonium indicate that a study of the impact properties would give a greater insight into the variables affecting the mechanical properties and formability of plutonium. In tension the a phase is quite brittle with elongations less than 1 pct. The ß phase at normal test speeds is unusually ductile; elongations up to 621 pct have been obtained. However, the ß phase is quite sensitive to strain rate; elongations decrease rapidly as strain rate is increased. The y and 6 phases are less ductile than the ß phase, with the 5 phase the more ductile of the two. Neither are very sensitive to strain rate. Considering the brittle nature of a Pu in tension and compression and the strain rate sensitivity of ß -phase Pu, both unnotched Charpy specimens and standard V-notched Charpy specimens were fabricated for testing. In addition, since iron in amounts greater than 500 ppm forms a Pu-PlgFe eutectic network which inhibits microcracking in as-cast plutonium,' it was decided to prepare impact specimens with low and high iron contents. Chemical analysis and density data for the impact specimens are presented in Table I. A total of 55 impact specimens, 32 unnotched and 23 with the standard Charpy V-notch were tested at temperatures from —45' to 330°C. The test results for both unnotched and notched specimens are illustrated in Fig. 1.

Jan 1, 1962

By The Mill Staff

"IntroductionCOMMENCEMENT of operations at the new No. 7 shaft and 10,000-ton mill at Creighton mine was a major step in the programme of conversion to all-underground mining by the International Nickel Company of Canada, Limited. Planned ten years ago, the orderly transition has been greatly speeded-up to offset the heavy drain on production imposed by World War II and also to meet the increased demand for nickel caused by the current international situation. Development of new mining methods, and process changes in the reduction plants, have made possible the economic recovery and utilization of ore of lower grade than formerly used and of varying metallurgical characteristics. By 1953, when the Company's open-pit mining operations are scheduled for completion, the hoisting capacity of its five underground mines in the Sudbury district will have been increased to 13,000,000 tons per year, compared with 5,700,000 tons of underground ore hoisted in 1950.Two types of ore occur at Creighton. One is a breccia and stringer type that contains a high percent-age of massive sulphides and is located in sheets along shears and in large and small pockets on the underside of the main norite mass; the other type, forming the main part of the ore zone, is mineralized norite that occurs as a •sheet up to 400 feet thick overlying tl1e breccia ore. In both types of ore the minerals of economic interest are pentlandite, which is intimately associated with pyrrhotite, and chalcopyrite. Early mining was confined to the breccia ore; this ore was mined by open stoping methods. The hanging-wall was later allowed to cave, with the result that the old stopes are now filled with caved low-grade ore."

Jan 1, 1952

By L. D. van Dyk, G. S. Tshofu

Iron ore fines are by-products of iron ore mining operations. Unlike iron ore lumps, fines cannot directly be used in conventional iron making processes, and consequently large quantities accumulate around the world. Pelletizing and sintering can be used to convert iron ore fines into agglomerates or briquettes for processing with lump ore, but these techniques are energy intensive and produce greenhouse gases. This research investigated the extraction of iron from iron ore fines using acetylacetone (a ß-diketone) as an environmentally friendly alternative process for fines utilization. A 2k factorial experiment design was used to identify the significant extraction variables. It was found that the reaction temperature and solid to liquid ratio had significant effects on the extraction process. The extraction kinetics were studied at different temperatures and the highest iron extraction (97 %) was obtained after 48 hours at 413 K and 0.025:1 (g:mL) solid to liquid ratio for a particle size range of +106 to -150 µm. The extraction products were easily separated from the unreacted acetylacetone by flash distillation and iron(III) acetylacetonate crystals were recovered. An economic evaluation showed that selling the crystals was profitable. Alternatively, the crystals can be reduced with hydrogen to iron particles and acetylacetone (for reuse).

Jan 1, 2015

By S. C. Tadolini, T. M. Barczark

Mines in the western United States have had limited choices for standing support. Wood cribs were often too soft and unstable. The introduction of the Can support in the earl v 1990s provided an effective alternative, (lilt/ it remains the dominant form of tail¬gate support. Water-filled prestressing cells are now used to cap the Can and preload it to provide an active roof load. The Cluster Prop, consisting of three timber wedge props bundled to¬gether; provides more capacity than (m equivalent sized Call support and improves transport efficiency. However the Cluster Prop is less stable and does not maintain a consistent load throughout its loading profile. Pumpable roof supports are another alternative support, but the \' have not been proven in high deformation en¬vironments. This paper compares the performance characteristics o f these various support systems.

Dr. Rossiter W. Raymond, Past President, Honorary Member, and Secretary Emeritus, died suddenly of heart failure at his home, 123 Henry St., Brooklyn, N. Y., on the evening of Tuesday, Dec. 31, 1918. -He is survived by his' wife and daughter. He was one of the founders of the Institute and its second President, his genius was the Institute's guiding spirit for 47 years. Dr. Raymond was one of the most versatile men of the day; an able mining engineer; brilliant professional writer; an editor of the first rank and an acknowledged authority on matters of literary style; a creator in the fields of fiction, children's stories, poetry and music; for more than 50 years the superintendent of Plymouth Church Sunday School. He will be revered by thousands as a loyal friend, generous giver, and admired colleague. His passing marks an epoch in mining and metallurgical literature. A memorial service will he held in the Auditorium of the-Institute Headquarters on Monday, Feb. 17, 1919, at 4.30 P.M.

Jan 2, 1919

By J. Meintjest

As you pointed out, furnace power factor (and consequently transformer MVA rating) depends upon the inductive reactance, and so it is desirable to design for the lowest possible value of this parameter. The further introduction on the primary side of the transformer of capacitors, whether in shunt or in series, increases the network power factor but does not alter the furnace power factor; that is, the phase angle between electrode to- hearth voltage and current remains unchanged. Corrigenda The following amendments should be made to the article entitled 'Coal-preparation routes for maximum coal recovery', which was published in the August issue (vol. 80, no. 8) of this Journal:

Jan 1, 1980