Search Documents

By A. M. Kiwior

In 1969, the Congress of the United States declared that "the first priority and concern of all in the mining industry must be the health and safety of its most precious resource - the miner," Therefore, Public Law 91-173, Federal Coal Mine Health and Safety Act of 1969, was enacted. Since haulage accidents account for a high percentage of coal mining accidents, Section 314e, ?Hoisting and Mantrips,? was included in the law. This section states: "Each locomotive and haulage car used in an underground coal mine shall be equipped with automatic brakes, when space permits. Where space does not permit automatic brakes, locomotive and haulage cars shall be subject to speed reduction gear, or similar devices approved by the Secretary which are designed to stop the locomotive and haulage cars with the proper margin of safety."

Jan 1, 1975

By E. Maritz

"The localized uniform conditioning (LUC) technique was proposed by Marat Abzalov in 2006. The technique converts conventional uniform conditioning (UC) grade-tonnage curves into single grade values attached to each smallest mining unit (SMU). This is achieved by ranking the SMUs within a panel in increasing order of their grade (based on the direct kriging of SMUs). This ranking is then used to localize the conventional UC grade-tonnage curves for each panel by dividing them into classes and computing their mean grades, which are assigned to the SMUs. The quality of this localization process will depend heavily on the validity of the grade patterns predicted by the direct kriging of the SMUs. Abzalov noted that where the distribution of data available for the direct kriging of the SMU is characterized by strong short-range variability, the advantages of using the LUC approach may be more limited. Consequently, a study was undertaken to determine how valid the predicted grade patterns of a typical Birimian-style gold deposit (with high nugget effect and strong short-range variability) might be expected to be. This was determined by comparing the direct SMU kriging ranking (based on sparse data) with the grade control model ranking (based on close-spaced data and the best available estimate of the deposit). The results showed a satisfactory correlation between these rankings and it was concluded that, although the grade patterns predicted by the direct kriging of the SMUs may be less meaningful for deposits exhibiting strong short-range continuity, there is nevertheless a convincing relationship with the actual (or best available) rankings. Therefore, the LUC technique is still considered to be useful for this style of deposit. IntroductionFor adequate technical and financial evaluation of a project, attempts should be made to estimate the recoverable resources – the portion of the in situ resource that can be economically extracted by mining. To achieve this, the estimates of the tonnage and grade of the mineralization should be produced above a given economic cut-off and should take into consideration the proposed mining selectivity."

Jan 1, 2016

By John Cogan

Field observations were made of rock phenomena in shale, dolomite, and fractured quartzite in the Burgin Mine, Eureka, Utah. Draft closure rates were measured with extensometers and convergence gages. In addition the effects of hydraulic props upon the retardation of closure was also monitored. Drift closure rates were found to be constant and to vary between 0.32 x 10-8 min-1 for dolomite and 23.8 x 10-8 min-1 for soft shale. The installation of props set at constant load served to retard the closure rates. General results show closure to occur at a constant rate for all cases, to be non-uniform around the drift openings, and to be increasingly retarded toward a zero rate by increases in prop load.

Jan 1, 1979

By Tom Learmont

The emergence of the dragline as the dominant stripping tool is described and reasons for this are noted. Brief comparisons are made with stripping shovels and wheel excavators. Representative output and machine availability figures for draglines are presented. The effect of changes in machine parameters such as boom length, swing power, and hoist power on machine productivity are discussed. An analysis of machine availability and the causes of machine downtime is made. Measures which are being taken to improve machine availability are discussed in detail. These include (1) improved methods of structural analysis, standardization of welded joints and welding methods to increase structural reliability and to develop more efficient structural designs, (2) standardization of gearing and mechanical componentry to permit the use of proven designs, (3) review of fairlead design and bucket hardware to improve rope life and reduce downtime, and (4) modifications to reduce maintenance time. The General Electric Data Logging system is described and consideration given to its use as a tool for improving productivity. Areas for future improvements in productivity are discussed.

Jan 1, 1976

By R. K. Ham, M. L. Wayman

TD-Nickel has been broken in tension and in fatigue at voom temperature. Rod specimens failed in tension by necking, with axial cracks attributed to voids elongated in the extrusion direction. Fatigue specimens failed in shear. Thin-film electron microscopy showed that the subgrain structure of TD-Nickel was very stable, and that particle-matrix detachment was very difficult, in tension and fatigue. TD-Nickel softened slightly during fatigue but had a high fatigue ratio (0.5at 10' cycles). Fractography suggested that Stage I fatigue crack propagation is greatly extended in TD-Nickel. Td-NICKEL* is a dispersion of 2 pct by volume of thoria (ThO2) in nickel, produced by powder-metallurgical methods including compaction, sintering, and extrusion. The spherical thoria particles, which may have a mean diameter of a few hundred angstroms, are dispersed with a mean planar spacing of a few thousand angstroms. By a combination of cold working and annealing, a subgrain or cell structure of dislocations intimately associated with the dispersion can be produced.' This gives the material useful tensile properties which are extremely resistant to exposure to high temperatures.'-= At the same time, the material shows considerable ductility.3'4 At the beginning of the present work, it was considered of great interest to investigate the mechanical stability of TD-Nickel under conditions of fatigue. On the one hand, materials which derive strength from a cold-worked structure are unstable in that they are susceptible to fatigue softening: in addition, the presence of discontinuities such as the particle-matrix interfaces might be expected to assist in the initiation and propagation of fatigue cracks, in that they may provide local concentrations of internal stress and sites for the initiation of voids." On the other hand, the substantial ductility of TD-Nickel suggests that if it obeys Coffin's relation8 (or the more refined form proposed by Manson9) it should have good fatigue resistance. The initial purpose of this investigation was to assess the importance of these factors. Also, relatively little fundamental work has been done on the mechanism of fatigue in dispersion-strengthened materials. Work on overaged A1-4 pct CU10-12 revealed a very large Bauschinger effect indicative of internal stresses at the particles, and very great fatigue hardening1' presumably due to the multiple slip stimulated by these internal stresses, followed by softening which was initially due to softening in the matrix, but later might have arisen from cracking at the particle-matrix interfaces. The study of overaged Al-4 pct Cu could not settle this latter point by the electron microscopy of thin films, since the dispersion is too coarse. A previous study of the fatigue of internally oxidized copper13 was complicated by inter granular failure, attributed to oxide particles at grain bouhdaries; internal oxidation of single crystals, however, improved their fatigue properties.'3 Investigations of SAP (sintered aluminum powder) are complicated by the complex particle shapes, and the possibility of continuous internal oxide films.14 It was hoped to avoid these difficulties with TD-Nickel, which had the further advantages that it was commercially available and suitable for study by the thin-film technique. 1) MATERIALS AND EXPERIMENTAL PROCEDURE TD-Nickel was purchased from the Driver-Harris Co. as 3/9-in.-diam rod which had been extruded, swaged, and "stress-relieved" (normally at 1010°C for 1 hr). Continuous-radius fatigue specimens with a minimum diameter of -0.1 in. were ground to shape and electropolished in 40 pct phosphoric, 35 pct sul-furic, 25 pct water at 25oC, with a stainless-steel cathode, at -6 v. Fatigue tests were carried out at room temperature with a Sonntag SF-1-U machine operating in push-pull at 1800 cycles per min, and in an Instron TT-C-L modified for reversed stressing at 26 cycles per min as described elsewhere.10 Round tensile specimens were ground with 0.85-in. gage lengths of 0.135 in, diam, electropolished, and tested in a Tinius Olsen hydraulic machine. The surfaces of fatigue specimens were examined with a Reichert metallograph. Discs for electron microscopy with a Siemens Elmiskop I were spark-cut 0.01 in. thick with a modified Servomet 11 employing a tool of moving molybdenum wire, cleaned in 50 pct acetic, 30 pct nitric, 10 pct phosphoric, and 10pctsul-furic at 85oC, and thinned by the window method in the electropolishing solution at -20°C and -6 v. Two-stage replicas (parlodion, then Pt-50 pct C self-shadowed at 40 deg) were taken from fatigue fracture surfaces for electron microscopy. Plane sections parallel to the specimen axis and containing the direction of fatigue crack propagation were polished, etched with Carapella's reagent, and examined optically. Transmission Laue X-ray photographs of as-received material electropolished to a point were used to determine preferred orientation. 2) RESULTS 2.1) The Structure of As-Received Material. Grains -1 µ diam and elongated 20 to 30 u in the direction of the rod axis were observed, With' elongated "intergran-ular" voids (-4 p diam and -90 µ long and identified as such using longitudinal and transverse sections and

Jan 1, 1968

By Morris Muskat

ANALYTICAL calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/3 in., and to approximately one half for a perforation radius of 1/4 in,, regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings.

Jan 1, 1942

By D. K. Sarkar, Ying Huang

"Superhydrophobic thin films were fabricated on aluminum alloy substrates by chemical etching followed by passivation with organic acid molecules; (ii) electrophoretic deposition (EPD) of functionalized ZnO nanoparticles and (iii) electrodeposition of organic-inorganic composite materials. The physical and compositional analyses of the deposited thin films were characterized by SEM, FTIR, XRD as well as contact angle goniometer. The contact angle and surface roughness of the superhydrophobic surfaces prepared by the chemical etching process were found to be 156° and 2.29 µm, (ii) by the EPD process were found to be 155° and 4.54 µm and (iii) by the electrodeposition process were found to be 159° and 7.11 µm, respectively.The corrosion properties were analyzed with both polarization and electrochemical impedance spectroscopy (EIS) in NaCl aqueous solutions. The results demonstrate that the superhydrophobic thin films on aluminum alloy substrates display better anti-corrosion behavior than the as-received aluminum substrate. The comparison of results pertaining to the compositional and corrosion properties of these thin films on aluminum will be discussed in this work.INTRODUCTIONSuperhydrophobicity is defined as a surface property which provides non-wetting characteristics with a water contact angle larger than 150°. It is observed that the creation of certain micro-nanoroughness structures promotes the entrapment of air in the spaces of the rough surface morphology. In addition, lowering the surface energy helps to reduce the affinity of water drops to the surface, thereby weakening the water-surface interaction. Recently, various fabrication methods for superhydrophobic surfaces have been explored (Sarkar, 2010, Huang, 2010, 2011, 2013, 2015a, 2015b), such as the sol-gel process (Brassard, 2011), plasma treatment (Marchand, 2013), chemical vapor deposition (Zheng, 2009), chemical etching (Saleema, 2011), electrodeposition (Ying, 2011) and electrophoretic deposition (EPD; Huang et al., 2015b)."

Jan 1, 2016

By Rodolfo Silva, Antonio Peres, Afonso Martins, Gilberto Ramalho, Mario Cabello

The consumption of aggregates in civil construction has increased considerably in Brazil for the last years. The extraction of sand and gravel generates significant environmental impacts. As the quarries and sand deposits are getting exhausted near the big cities, the price of aggregates is increasing. Meanwhile, the extraction of quartzite (dimensional stone) in the state of Minas Gerais has been done mostly in small quarries, with very low recovery, generating approximately six million tons of wastes a year, which causes pollution, increases final prices of products, decreases the life time of quarries and ends up in the closure of enterprises. The government agencies and the quarries’ owners understand that only by finding applications to wastes there will be development to the sector. The aim of this investigation was to study the application to the quartzite wastes as aggregate in the civil construction. Samples of quartzite wastes collected in a quarry were characterized by petrographic analyses. Laboratory tests of crushing and grinding were done to analyze the viability of reducing the size of coarse material to a finer one to be used as raw material in industrialized mortars and concrete pre-molded components.

Jan 1, 2014

By B Murphy, S O’Connell, J L. Heath

In the 1989 best-seller The 7 Habits of Highly Effective People, the author, Stephen Covey, highlights the importance of maintaining not only ‘production’, but also, ‘production capacity’. When operating a modern flotation concentrator, production is often measured in terms of concentrate tonnage, tonnes milled and plant utilisation. There are very few metrics that focus directly on flotation equipment condition in relation to performance, which is analogous to Covey’s production capacity principal. It is evident on many mine sites that flotation equipment condition is not monitored on a proactive basis and that the prevailing culture is to wait for a failure, before addressing an issue.This paper discusses examples of how poor equipment condition can lead to production loss through poor metallurgical performance. Actual examples are given where these problems have occurred in operating plants. An outline is provided on how metallurgical and maintenance departments can work together to protect production capacity and gain more from existing equipment.CITATION:Murphy, B, O’Connell, S and Heath, J L, 2014. Maximising value through maintaining your flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 71–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Hanjie Chen

Mining experiences have shown that in a pitching seam, roof behavior is significantly different from a flat seam. Uphill mining usually experiences more roof problems than downhill mining. Based on a case study at RAG American Coal Company, Willow Creek Mine, this paper presents the roof control problems experienced in a high pitching seam. Then, finite element modeling is conducted to analyze the roof stress distribution for an entry developed in different directions relative to the seam strike. The results shows that seam inclination has a significant effect on roof stability in terms of tensile stress. Uphill mining experiences higher tensile stress than downhill mining. The modeling technique utilized in this analysis presents a first of kind methodology.

Jan 1, 2000

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

By E. R. Hoskins

Results of a primary stress measurement investigation conducted on the 1100 copper ore body of the Mt. Isa mine, Mt. Isa, Queens., Australia, are presented in this chapter. The investigation started in September 1965, after discussion with the engineering staff at Mt. Isa, and consisted of both underground or in-situ tests at Mt. Isa and laboratory tests on Mt. Isa rocks and stress measurement techniques at the Australian National University in Canberra. Underground stress measurements were made in and adjacent to the 1100 copper ore body. The primary stress measurement site was in J 32 west crosscut on 14 Level. Approximate coordinates on the mine grid are 3000 north, 1650 east. The vertical depth below ground surface at this point is approximately 2180 ft. Some preliminary measurements were made in M 30 west crosscut on 13 Level, coordinates 3000 north, 2000 east, depth beneath the surface approximately 1990 ft. Additional flatjacks were installed on 11 Level in L 30 west crosscut, coordinates 3000 north, 2200 east, and depth beneath the surface approximately 1580 ft. All of the sites were in rock that from a mining engineering viewpoint must be considered extremely sound. The 13 and 14 Level crosscuts were approximately 14 ft on a side and nearly square and the 11 Level crosscut was approximately 10 ft on a side. All of the crosscuts had been standing open for several years and no artificial support of any type was necessary. Extraction openings hundreds of feet on a side have been made in this mine in similar rock and these have remained open also without additional support (see Davies 1 for a recent summary of mining techniques and conditions). The geology of the Mt. Isa mine has been most recently described by Bennett.2 Briefly, Mt. Isa is a silver-lead-zinc and copper mine in a series of Precambrian siltstones, shales, and bedded carbonates that strike north-

Jan 1, 1972

By W. L. Dalke

The Minntac complex is a facility for production of iron ore pellets located on the Mesabi Range at mountain iron, Minnesota. It consists basically of a mine, crushing plant, concentrator, and a pelletizer producing twelve and one-half million tons of pellets annually. This paper deals with some of the aspects of the grinding circuits; but prior to that discussion, it might be well to briefly describe the flow of material in the operation. The crude ore, containing from 20% to 25% magnetic iron, is mined by 14-yard electric shovels. .the blasted ore is loaded directly into 50-yard side dump railroad cars and hauled to the crushing plant. Crushing is done in three stages, originally, two 60" primary crushers; four 7-foot standard secondary crushers; and six 7-foot short head tertiary crushers were installed, when the plant was expanded to double its capacity, five secondary and ten tertiary crushers were added. These were duplicates of the original 7-foot standard and short head crushers used in the original construction, there was no expansion of the primary crushers but a one-half-million-ton surge pile of tertiary crusher feed was added.

Jan 1, 1976

By Ronny J. Sadri

Under contract to the Department of Energy, Fluor Mining & Metals, Inc. and Bonner & Moore Associates developed a group of computer models that can be used to simulate single seam dragline operations. These models have been subsequently modified by Fluor for use in multi-seam dragline mining situations. The single seam model analyzes the digging, spoiling, and walking patterns of draglines to identify possible parameter changes to increase productivity. Parameters such as key-cutting, panel width, digout length, and bench height, etc., are analyzed in this process. The models were tested using data from four operating mines. Field demonstrations were performed to correlate computer optimization results with field data. Productivity was greatly enhanced at one mine site by a change in some of the operating parameters. The multi-seam study has as its objective the development of a broad- based mine planning tool which would be used to identify and quantify the different procedures employed in multi-seam dragline mines to increase their productivity. The major problem identified in multi-seam mining is the sequencing of the different stripping and mining operations. The multi-seam model has the same capabilities as the single seam model. In addition, it models up to four seams with three partings per seam. It allows the operation of several draglines at different levels, and analyzes the effect of ramps, rehandling, and ancillary mining equipment.

Jan 1, 1982

By W. L. Price

The intelligent selection of wire cloth and perforated plate for screening surfaces seems a rather confusing subject to the newcomer in aggregate processing. The proper application of various screening surfaces is a complicated one and one could consider himself an expert only after many years of working with all applications. However, part of the subject matter could be simplified considerably for, the average screen user. In this paper an attempt will be made to do this, by presenting some comparative specification data along with cost figures Unfortunately, it is impossible in the limited scope of this paper to give actual service comparison records between different cloths or cloth and plate. Anyone who has considered making actual service comparisons for competing screening media is well aware of the almost insurmountable problems Their solution would form the basis for a separate paper on that subject alone. Therefore, this paper will be limited to comparative data up to the point of installation.

Jan 1, 1961

By Robert E. Wood

[The temperature dependency of the low-density thermal conductivity coefficients, ?°T, of nitrogen, 100° to 1,200° K, is correlated with the Keyes' equation, ?T ½ -1 -12/T) WT = aT+ bT 10 The equation ?T,P = ?°T +a[ ]ß represented 509 experimental higher V pressure thermal conductivities in the temperature range 131.2° to 973.15° K for pressures to 500 atmospheres, with a mean absolute deviation of 2.35 percent. This equation was used to compute thermal conductivities of gaseous nitrogen for 47 pressures, 1 to 240 atmospheres, and 110 temperatures, 133° to 740° K, which are common to conditions encountered in Bureau of Mines helium purification processes. Isobaric heat capacities, CP, and viscosities, ?T,P, from previous work were combined with the present thermal conductivities, ?T,P, to compute Prandl1 numbers, C?T P / ?T ,P, of nitrogen. Tabular values of Prandtl num¬bers are presented for 49 pressures, 1 to 240 atmospheres, and 75 temperatures, 133° to 740° K. Estimated uncertainties are ±5 percent in the tabulated thermal conductivities and ±15 percent for the computed Prandtl numbers. However, the uncertainty may rise to ±10 percent for thermal conductivities and to ±30 percent for Prandtl numbers as the critical conditions of nitrogen are approached.]

Jan 1, 1971

Introduction The objective of the design and operation of a mine is to make as much money as possible within certain reasonable and responsible constraints. The imposition of constraints on the objective of maximizing profits can result in an optimum mine design. This paper deals with the maximization of profits. Optimization will be discussed in a future paper. In the mining industry, it is generally accepted that the maximum economic recovery is defined by identifying the reserves and the sequence of mining that results in maximum net present value (NPV) or discounted cash flow-rate of return (DCF-ROR), as indicated in Fig. 1 (see Lemieux, 2000). Current parametric analyses techniques, such as varying the mining costs; profit reservation; sales price or metal content, to define pit limits and mining sequence technically referred to single, double or triple parameterization, do not assure that the curve in Fig. 1 will be maximized. In defining the sequence, the first material to be mined should be the first grouping of recoverable mineral that has the highest after-tax unit value and that forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable and practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. I is constructed by calculating the NPV for a series of sequences, each assuming operations are terminated on successively lower profit pits. If the operation ceases on a pit with too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and then starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have produced a greater return if it was invested at the dis¬count rate. The maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV or DCF-ROR. Pit and phase definition The real challenge of reserve definition is identifying the phasing and after-tax profit per ton, so that the curve in Fig. 1 can be plotted. The after-tax profit cannot be properly addressed until after the pits are designed, the production is scheduled and the cash flow is estimated. Throughout the years, many investigators have ad¬dressed this problem. A major thrust of the famous paper in which Lerchs and Grossman (1965) presented their algorithm was to identify a sequence that would produce a result similar to that identified in Fig. 1. Whittle's (1988) four-dimensional analysis is designed to address this issue. The author addressed this same issue in a paper presented to the 1968 Canadian Institute of Mining national convention (Lemieux, 1968). Without a relatively simple methodology to con¬struct the curve in Fig. 1, the number of iterations in a trial-and-error method becomes prohibitively burden-some. The pit designer seeks a simple pit-planning parameter that will serve as a proxy for the after-tax profit per ton used in defining the curve in Fig. 1. The designer's goal is to apply this pit-planning parameter using standard pit-wall location techniques to design a series of pits that will provide a guide to the sequencing. Common techniques used to position pit walls are strip-ratio limits, highwall incremental analysis, floating-cone methods or "maximizer" applications1. Costs, revenues, noncash charges, taxes and profits are usually structured on a unit basis for use in the pit-wall location analysis. Application of the proxy parameter using the pit-design tools should, ideally, result in the definition of pits and sequences that will maximize the curve in Fig. 1. 1 The pit-design tool frequently referred to in the literature as an "optimizer" defines a pit boundary that maximizes the value contained within based on the input parameters and the safe pit-wall angle. The optimization of the pit design involves selection of rate of production, cutoff grade, product quality and other considerations. These considerations constrain the maximization of value. Therefore, pit-design tools that maximize value should be called "maximizers."

Jan 1, 2000

By Ali Kahriman, Olivio Angelini, Ibrahim Sefer, Burak Ekmen, Koray Arpak, Ertugrul Kaya, Yucel Karakus, Abdullah Sak, Aziz Ozdemir

In recent years, in order to bring solution to traffic intensity arising from transportation problems and facilitate public transportation in the modern world in paralel to urbanization and to the increase in population, it’s well known that, the construction of Access tunnels is inevitable. The driving of the tunnels is a subject of special interest in the technique of rock blasting. The essential factors in terms of tunnel driving and safety in tunnel blasting that is applied in metropolitan areas, an in depth knowledge of ground vibrations and the ways of reducing them to safer levels.

Jan 1, 2010

By R. J. Heemstra

A method was developed for calibrating photographic emulsions and retrieving working curves for emission spectrography. The values obtained from a digital readout or a recorder chart of a comparator-microphotometer are converted to light intensity values using an emulsion characteristic curve derived from a quartic polynomial preliminary curve. The characteristic curve, consisting of Seidel transform versus the logarithm of intensity, is split into two cubic polynomials at the zero value of the transform, resulting in eight emulsion calibration coefficients. These methods allow use of the calibration curves even at very small and very high intensities, thus extending the range of analysis. Use of a small computer allows rapid calculations. A computer program was written to formulate, code, and file each working curve along with its statistical error. Proper coding of the input data permits the direct printout of the concentration of the elements under investigation.

Jan 1, 1970

By Fernando Aracati Botelho, Jose Antonio Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo

"1 AbstractThe production of alumina from bauxite using the Bayer process generates 0.7 to 2.0 ton of the residue known as red mud and about 800 kg of CO2 per ton of alumina. The direct use of exhaust gases to react and neutralize the bauxite residue may allow a double gain: open a wide range of new applications for bauxite residue reducing its reactivity and sequester from 3 8 to 107 kg of CO2 per ton of alumina. This paper shows a pilot scale reaction of a suspension of bauxite residue-water with flue gas produced from direct burning oil, similar to the exhaust gases of a refinery. Two different types of reactors are used, a spray tower and a packed column. The inlet and exhaust gases are analyzed using electrochemical cells and non-dispersive infrared sensors. The pH of the suspension is monitored during the reaction and after to evaluate the buffer effect. 2 IntroductionThe production of millions of tons per year of alumina around the world generates from 0. 7 to 2.0 ton of the residue known as red mud (RM) per ton of alumina. The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity this material is considered dangerous and currently there is no operating process capable of reusing all the material produced at any refinery. These lakes after filled of solid material eventually have the surface revegetated [4]. In any case they will remain as an environmental passive and needs monitoring for decades. The search of a industrial process that combines the reduction of the CO2 emission and the reduction the pH of the red mud opening the possibility of large scale and economically viable ways is the main objective of this work.The use of the exhaust gases of the refmeries to neutralize the bauxite residue may allow a double gain: Open a large array of new applications for the residue with the reduction of its reactivity and sequester millions of tones ofCO2 plus other gases like SO2 [7] and NOx. This project studies the reaction of the exhaust gases from a boiler burning diesel with RM in different reactor types and conditions in order to obtain parameters to design equipment capable of process this reaction on a larger scale. With these objective compositions of red mud were processed with flue gas at concentration similar to the exhaust gases of the calcination process and boilers of the refmeries."

Jan 1, 2012