Search Documents

By Richard E. McElvain, I. Cave

The selection of centrifugal pumps for mill discharge duty should be based on the total circuit concept. The practice of operating the mill circuit based on limitation of the pump can result in losses in one day which would offset the pump cost. Operating data from 25 grinding circuits have been reviewed and comparative results on added mill capacity have established advantages far beyond the less significant maintenance costs with increased circulating load and better cyclone operation. Mill discharge pumps should be selected on the following basis: i) Best available design for wear performance ii) Size to provide best economic life iii) Liner material best suited to circuit conditions Pump efficiency is a secondary consideration because power consumed by pumps is small compared to mill power input. Energy dissipated in mill pumps is contributing to comminution of ore.

Jan 1, 1982

By Arash Maghsoudloo, Asli Can

"Abstract This paper presents a ground improvement implementation case under a raft foundation of a local hospital. The selected ground improvement method is Wet Soil Mixing (WSM) technique. Soil mixing is increasingly applied to environmental applications and ground stabilization in geotechnical projects. In this technique, weak soil is mixed with cementitious slurry to improve the characteristics of the soil. The investigated case is one of the pioneering WSM ground improvement technique implementation cases in Turkey. The soil profile is mainly consisted of low plasticity clay. The effect of ground improvement is verified by a series of laboratory tests and four in-situ pile loading tests. The results of in-situ pile load tests on constructed soilcrete columns showed an acceptable factor of safety for the bearing capacity of the WSM columns. Measured bearing capacities in all four tested columns were nearly 20% higher than calculated values. In addition, a set of samples are obtained from the constructed columns and unconfined compression tests have been conducted. The laboratory test results indicate that the selected cementitious slurry has a sufficient efficiency to form the stabilizing columns.IntroductionIn the construction industry, stabilization of the soft ground by lime or cement stabilization is a widely used technique. In ground improvement systems deep mixing method (DMM) results in the same stabilization in deep portions of the soft soil profile by mixing cementitious slurry by means of mechanical augers. The pioneering cases of modern deep mixing application can be traced back to the year 1970 that was used for the stabilization of marine soils below the water level for the construction of harbor structures (Terashi et al., 1979). Nowadays, DMM is shown to be a proper and efficient method for the foundation of the structures and embankments on land. Some recent studies also reported that reasonable settlement reduction range in the stabilized soils under the foundation of structures (Archeewa et al., 2011). In addition to reduction of the structural settlement under service loads, deep mixing methods are also utilized when there is a concern with contaminated soil and groundwater or groundwater control (Andromalos and Bahner, 2003).Although, the DMM is shown to be a successful method in numerous studies for improvement of a wide range of soil types such as organics, fine-grained, and coarse grained material, it has some limitations (Archeewa et al. 2011, Jameson et al. 2010, Jelisic and Leppanen 2004, Lambrechts and Roy 1997, Meyersohn 2007, Miki and Nozu 2004, Olsson et al. 2008, O’Rourke and McGinn 2004, Stewart et al. 2004, Yang et al. 2011). High soil density and stiffness could damage deep mixing rigs. Engineering properties of the soilcrete columns changes based on the soil type, water content and other factors such as organic content of the available soil profile, so properties of the generated soilcrete should be verified by a set of rigorous testing procedures (Puppala et al. 2004).Based on the general classifications presented in the ground improvement literature, deep soil mixing method is divided into two main types of dry or wet mixing methods. In the dry and mixing methods compressed air and water are utilized as the binder transporter medium respectively (Moseley and Krisch, 2004). In addition, DMM methods can be categorized based on the employed mixing methods during the construction. In this study, the main aim is to present and elaborate on the selected method is known as Wet Speed Soil Mixing (WSSM)."

Jan 1, 2014

By L. Russell Payne

The use of shock tube in the blasting industry is relatively well characterized and understood within the realms to which it is used. Non-conventional uses of shock tube within the EOD and the Aerospace Industry however has not been as widely researched and published. Characteristics of shock tube such as its reliability, simplicity and its non-electric nature make it ideal for functioning or driving mechanical mechanisms, detonators, and timing devices. Outlined in the text are the performance characteristics of shock tube in an array of atmospheric environments including pressures ranging from ambient to 100,000 ft equivalent atmosphere. In addition the useful exit work energy or impulse of the shock tube for driving these various EOD and Aerospace mechanisms is published as a function of tube lengths and atmospheric pressures. Of particular interest to these devices is the required length of shock tube needed to produce the steady state detonation energies and the accompanying properties of the shock tube at these lengths. Various sources publish an arbitrary run distance for steady state detonation and output some where between 20 cm and 1.0 meter. Statistical and experimental evidence with in the text show these numbers to be low and provides an updated reference for shock tubes usage in nonconventional situations.

Jan 1, 2008

By Juan Carlos Gentina

La biolixiviación de minerales es un proceso metalúrgico que permite el tratamiento de sulfuros insolubles y óxidos insolubles y ofrece beneficios económicos, ambientales y tecnológicos. En ese sentido, el presente texto señala un panorama de biominería y minería de cobre, la influencia de las variables operacionables más relevantes y su situación actual y presente en Chile.

Dec 1, 2013

By Sung-Mo Jung

Experiments were carried out on a system with artificially prepared slags in a graphite crucible, in order to examine the possibility of recycling BOF slags produced in the steelmaking process. More than 80% of FeO and P2O5 was reduced within 20 minutes and the FeO reduction rate was greater than that of P2O5. P2O5 reduction began after more than 60% of FeO was reduced. Increasing slag basicity enhanced the reduction of FeO and P2O5. Temperature also improved slag reduction. The overall reduction rate was controlled by the chemical reaction at the slag/carbon interface. The reduction rates of FeO and P2O5 were second and first order with respect to their respective contents. Most of the reduced phosphorous is believed to vaporize in the form of P2 gas.

Jan 1, 2006

Multi Torque Industries and Jadefoil have developed a safer, more efficient method of explosive protection, retention, placement, and constraint. In particular, this refers to advancements in airbag technology, where the system will offer an alternative to conventional gasbags and decking methods to provide a far more controlled and safer working environment. Airbags have provided operator control and reliability which has not until now been possible in this type of application. The benefits have been noted by current users and the advantages have provided an increase in productivity and significant savings in explosive waste. Obvious problems with gasbags lie in their instability in hot conditions where the danger is associated with gas canisters exploding with great force posing a significant risk to operators. Other problems associated with the decking systems currently on offer is the lack of versatility and operator control. The airbag systems give the operator full control to guarantee accurate placement, assured retention whilst boasting a quick operation of less than a few seconds for conventional void blocking, decking and plugging. One of the main advantages of the airbags is that the operator has full control over placement and retention force, therefore in wetter conditions where slippage can be a problem extra air can be added at the operatorÆs discretion to ensure a sufficient grip. Technical calculations coupled with experimental testing have demonstrated that an airbag will support the weight of a 30 m water column in an 89 mm hole at an initial bag pressure of 5 psig. Applications are increasingly growing whilst more customers embrace their use. Advancements such as the ability to deck in overhead holes, block voids in overhead holes at any depth, explosive retention in very wet conditions, longhole stabilisers to prevent hole closure and concertinaed liners reflect a dynamic potential for new technologies. All of these applications provide a decrease in explosive waste, an increase in operator safety, an increase in explosive protection, and an increase in productivity.

Jan 1, 2004

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few ? but very important ? instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012

By N Redwood, N Fowkes, A Bassom, S Durkin

"It is well known that from time-to-time a vehicle will interact with a bund or windrow and often the barrier is insufficient to safely arrest that vehicle. The result of such an incident is often catastrophic. Regulations around the requirement for edge protection near pit edges vary between jurisdictions. Generally in Australia regulations tend to be around placing the responsibility on the mine operator to provide ‘adequate’ or ‘appropriate’ edge protection. Guidelines often place a minimum height of bund at between half and two-thirds the diameter of the largest tyre on-site.Safescape has identified the opportunity to improve safety in open pit edge protection and is currently developing the Edge Protector (EP) product. The EP is designed to create a vertical front face to a conventional broken rock safety bund. The fundamental premise of the product is that by creating a vertical front face to the bund, trucks cannot easily drive up over the bund and instead have to push through the rock to get to the other side.In addition to providing a safer system for arresting vehicles, the vertical front face also means that extra space is made available in the haul road. This can either be used to facilitate larger trucks or when designing a new mine, with an increase in overall pit slope.This paper outlines the research and development of a new edge protection product. Discussion will include project objectives, economic incentive for mines to apply the system, mathematical analysis of the truck/bund interaction and physical testing of the product.Citation:Durkin, S, Fowkes, N, Redwood, N and Bassom, A, 2016. Innovative Approach to Open Pit Edge Protection, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 138–149 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By John R. Troxell

"INTRODUCTION Lookout Mountain is the natural barmier that isolates Dade County from the rest of Georgia. Legend has it that Dade County seceded from the Union long before the rest of the State of Georgia and did not officially return until July 4, 1945.Coal mining began in the Lookout Mountain area in 1891, and by 1894 production amounted to about 1,000 tons daily. Present production by the two principal operating companies is about 3,600 tons monthly.In the Sand Mountain area, coal has been mined intermittently since before the Civil War, and probably 6,500,000 tons has been produced.The Bureau of Mines coal project was initiated to alleviate a possible coal shortage and to assist the State in developing coal deposits to supply State institutions and local markets. Drilling began January 1, 1945, and ended May 11, 1945, after 2,907 feet had been drilled. By this time the Georgia Power Co. became interested in northwest Georgia coal fields as a possible source of more economic fuel for their steam-driven power plants, but the Bureau continued to act in an advisory capacity to the power company until June 30, 1945."

Oct 1, 1946

Jan 1, 1949

As has been the case since the early Phoenician traders, the minerals used by modern man come from deposits scattered around the globe. The price received is more and more being set by worldwide supply and demand. Thus the price component in the profit equation:Profits = Material sold (units)x(Price/unit û Cost/unit) is largely determined by others. The recent price history for two of the major metals, copper and iron, are given in Figures 1 and 2, respectively. As can be seen there has been a steady decline in the prices (when expressed in constant dollars) over the 20 years which have lapsed since the first of the International Conferences on Mass Mining, æDesign and Operation of Caving and Sublevel Stoping MinesÆ was held. If one would look back over the entire 20th century this would also be the trend. Cost containment/reduction through efficient, safe and environmentally responsive mining practices is serious business today and will be even more important in the future with increasing mining depths and more stringent regulations. A failure to keep up is expressed very simply as: Profit This, needless to say, is unfavourable for all concerned (the employees, the company, and the country or nation). The mining companies have had to look at ways of reducing the expense part of the profit equation while maintaining safe, environmentally conscious operations. Table 1 summarises the rules for working in todayÆs economy.

Jan 1, 2000

Jan 1, 1913

By L. M. Barker, E. G. Lewis

The literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: 1. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the litera- ture of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others—a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1943

By Andreas Ludwig, Abdellah Kharicha, Menghuai Wu

"In order to demonstrate how CFD can help scientists and engineers to better understand the fundamentals of engineering processes, a number of examples are shown and discussed. The paper will cover (i) special aspects of continuous casting of steel including turbulence, motion and entrapment of non-metallic inclusions, and impact of softreduction; (ii) multiple flow phenomena and multiscale aspects during casting of large ingots including flow induced columnar-toequiaxed transition and 3D formation of channel segregation; (iii) multiphase magneto hydrodynamics during electro-slag remelting; and (iv) melt flow and solidification of thin but large centrifugal castings.IntroductionSince the Bronze and the Iron Ages, material processing, and here especially metallurgy, has got a global importance for the economic well-being of the societies. It is thus understandable that metallurgy has changed from arts and crafts into an engineering specialty, where the knowledge of centuries has lead to an enormous commercial and technical efficiency. However, increasing competition and the necessitation of energy and CO2 reduced manufacturing methods requires the improvement of existing techniques and even the development of new, alternative production technologies. On the other hand, the opacity of liquid and solid materials and the involved high temperatures makes the experimental penetration of metallurgical processes and with that the attainment of detailed process knowledge quite difficult."

Jan 1, 2012

By H. H. Yancey

In this information circular is presented a summary of the more important articles that nave appeared in the literature pertaining to the experimental work and to the commercial operation of the froth-flotation and Trent processes as applied to the cleaning of fine coal.

Jan 1, 1933

By Jennifer Riefenberg

Underground coal mines often experience ground control problems related to weak floor. Developing a methodology for rating floor quality can aid in understanding and delineating ground hazards. U.S. Bureau of Mines researchers are currently exploring methods for generating ground control hazard potential maps. One component of hazard potential in floor-heave-prone mines is delineating floor quality and its correlation with failure. Although field exposures are limited, significant information on the roof and floor quality can be gained through analysis of existing drill core data. Drill core data and roof and floor exposures were analyzed for quality. Laboratory tests were run on 50 core samples to evaluate, compressive and tensile strengths of various roof and floor lithologies. Extensive geologic and lithologic examinations of the cores and samples were also completed. Results of this work involve the formation of a preliminary quality rating for coal mine floor using a modified Coal Mime Roof Rating (CMRR).

Jan 1, 1995

By S. M. Shelton, J. B. Zadea, M. M. Fine, T. L. Johnston

"INTRODUCTION The Mayfield manganese property is about 25 miles south of Van Horn, in Jeff Davis County, Tex. The ore deposit is developed by a large open-cut and a small stope.An 8-ton sample was received for testing; it was taker at random from material on the mine dumps and consisted of a mixture of manganese oxides, barite, and siliceous gangue minerals. The manganese occurred largely as hard, massive, crystalline psilomelane, with a small amount of pyrolusite. The gangue minerals consisted of intermixed iron-stained sand stone, quartzite, chalcedony, calcite, quartz, and barite. Chemical analysis showed 8.9 percent manganese, 3.3 percent iron, 38.4 percent silica, 6.6 percent calcium carbonate, 7.1 percent barium, 3.1 percent alumina, 0.09 percent phosphorus 0.01 tungstic oxide, and less than 0.05 percentAnalysis of selected clean pieces of manganese minerals, free of gangue, showed 48.1 percent manganese end 13.4 percent barium, of which only 0.2 percent was present as barium sulfate. This indicated a limit in concentration. Barium was also present in the gangue as a separate mineral, barite (BaSO4), which has approximately the same specific gravity as the manganese oxide."

Apr 1, 1942

By Robert J. Brison

On the basis of experience accumulated during the completion of some 150 gold/silver process development projects, general guidelines are presented for developing the most cost effective process for a specific project. Steps involved in process development for lode ore deposits generally include a review of pertinent background information on the ore deposit, sample procurement and preparation, sample characterization, study of concentration possibilities, investigation of leaching and metal recovery methods, economic evaluation of alternative processes, optimization of the selected process, a pilot plant program if warranted, and finally, process design and feasibility studies. Each of these steps is discussed, with emphasis on the relation between technology and economics.

Jan 1, 1984

By H. Sevim

This paper summarizes the research effort in simulating the operation of "Underground Coarse-Coal Hydrotransport Systems" (UCCHS). The equipment of the system to be simulated is already optimally selected by using an analytical optimization model. The purpose of the simulation model is to test the performance of the system and to obtain the distributions of operating parameters such as water and power consumption and amount of slurry delivered to the preparation plant. Knowledge of the distributions of these parameters is essential for the efficient operation of the system.

Jan 1, 1987

By B Lumsden, R Smiles

Independence Group’s Jaguar Mine treats a polymetallic ore producing a copper concentrate and zinc concentrate. Effective separation of the sulfides requires relatively fine grinding with flotation feed P80 of about 75µm. Zn losses to final tails are greater than 60 per cent and <32 µm. When magnetic conditioning was first installed in 2010 it showed about an 8 per cent reduction of zinc in final tail and on some ores a similar benefit for silver as well. Current testwork is showing about a 12 per cent reduction in zinc and silver in final tail, consistent with the original testwork. Sizing of the final tail during the tests showed that the reduction of zinc and silver losses were only in the <32 µm fraction, as would be expected from an aggregation process. However, the most surprising result was about a 4 per cent reduction in zinc and silver in the plant feed with a >99 per cent statistical certainty. The reduction in zinc and silver in the feed is also only in the <32 µm fraction. Therefore, because the magnetic conditioning of Zn flotation feed cannot impact plant ore feed grade the hypothesis is that the magnetic conditioning is reducing the fine mineral from downstream processes, like filtering and thickening, returning to the plant feed in the recycled process water. This hypothesis is consistent with plant observation of dirty concentrate thickener overflow and measurements of solids in the overflow, as well as the average % Zn grade in cyclone overflow that correlates with the magnetic conditioning ON and OFF days. This paper presents these plant test results.CITATION:Smiles, R and Lumsden, B, 2018. Improving fine sulfide mineral recovery in Independence Group’s Jaguar Mine zinc circuit, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018