Search Documents

By Hutton A. C

Quantitative X-ray diffraction (XRD) analyses using the Rietveld method, a standardless technique for full XRD pattern fitting, showed the mineralogy of the eastern Queensland Tertiary lacustrine oil shale deposits is dominated by detrital cla

Jan 1, 1994

By R. Debkowski

Mining methods used to protect the workings in underground salt mines against the destructive activity of natural factors are presented in this paper. Major hazards and methods of elimination of their impact on the stability of workings, were determined. Old and modern technical means and technologies used for protection and preservation of the selected most interesting sites were characterized. The results of surveys and studies allowed proposing the change of mine structure i.e. dividing it into monumental and not-monumental part, which should improve execution of necessary protective works.

Jan 1, 2006

By D. Y. Kim

This paper shows an approach that a gondola-typed robot recognizes walls on building facades. It is applicable for autonomous or teleoperated building façade painting robots. The robot may react based on the wall classification data. This approach is based on 2D LRF(two-dimensional Laser Range Finder). The robot acquires relative distances to walls, and a Kalman filter decides correspondence of walls. An ARS(Attribute Reference System) sensor helps convert LRF coordinate to global coordinate. The experimental results demonstrate the conversion of LRF data.

Aug 1, 2013

This paper describes the new iron and steelmaking process recently commissioned at NZ Steel. Ironsand mined and concentrated at Waikato North head is slurry pumped 18 km to the company's Glenbrook works. Ironmaking includes the direct reduction process pioneered at Glenbrook in the 1970s and a new continuous electric melter. The molten, high carbon pig iron produced is then fed to a vanadium recovery unit and on to the KOBM oxygen steelmaking vessel. Steel is cast into billets or slabs. The new plant, which is the first stage of a fully integrated works at Glenbrook, raises New Zealand Steel's production capacity from 150 000 t/y to 750 000 t/y.

Jan 1, 1986

By David Morrison

"The history of the mining industry is littered with in-pit crushing and conveying (IPCC), which should not be confused with the International Protocol for Carbon Capture, projects that failed. The failure is not the technical one of “did it achieve the desired tonnage rate for a longish test period” but, rather, the far more important one of “did it provide return on the investment in the manner that was promised?” While quite a few can claim the former, very few system installations can claim the latter.The reasons for the many failures are numerous, but they are all characterized by a combination of an element of engineering optimism in any, or all of the production rates, the productivity, or the operating and maintenance costs and in predicting the continuity of operating conditions. In these days of big data, propagating such a situation is rapidly becoming unforgivable.In this article, the three most common scenarios put to the corporate board for approval, and the logic as to why they were selected, are examined (with the irony included intentionally).• Fully mobile crusher, fed by a shovel and conveyed out of the pit to a waste dump / process plant.• Semimobile crusher (much more expensive than a fixed crushing station but which apparently allows trucks to short haul inside the pit and improve productivity), which moves when the face moves.• Relocatable crusher (more expensive than a fixed crushing station but which gets relocated at great expense after all the fixed infrastructure impeding relocation is demolished) fed by trucks that don’t leave the pit mostly.This paper will also consider the truth about their operational performance and associate costs."

Dec 1, 2016

By W W. Moorhouse

A survey of recent literature indicates that sulphides occur in the volcanic rocks of the Archean, or in sedimentary rocks intercalated with the volcanic rocks. The thick sedimentary sections are generally poor in sulphides. Thus, the widespread pyrite and pyrrhotite mineralization in the Archean may be largely of volcanic origin. Introduction I N this paper, commercial base-metal deposits will not be considered, as they are dealt with in other papers of the Symposium. Instead, attention will be focused on those sulphides, often associated with graphitic argillites or tuffs, which have appeared in such embarrassing abundance in electromagnetic surveys of Archean areas. The data on which the paper is based are drawn from recent reports of the Ontario Department of Mines, the Quebec Department of Natural Resources and the Geological Survey of Canada. The information available from these sources is unfortunately limited, because sulphides commonly occur in sheared rocks, such as black argillites and tuffs, which rarely form conspicuous outcrops, and may not be exposed at all. Thus, in the absence of geophysical information, even detailed mapping may fail to reveal the presence of sulphide-rich rocks.

Jan 1, 1965

By Ira Joralemon

THE sampling of disseminated copper deposits has been described often but the method of combining assays, to give the true shape and value of the orebody as it will be mined has received less attention. As the ore mined during five or ten years at several of the great disseminated properties has averaged materially lower in grade than the published estimates, the question of the sampling and estimating of these orebodies seems timely. In this paper, attention is given particularly to factors that may cause errors in the final estimate. Sampling of diamond-drill holes, churn-drill holes, and underground workings is briefly described in the first part of the paper; then the method of combining assays to give the average grade and tonnage that will be mined is taken up in some detail. The necessity of study of the geology of the deposit and of probable costs is emphasized. Finally, the methods of calculating tonnages are outlined. DIAMOND-DRILL SAMPLING There are three main requisites for accurate diamond-drill sampling. First, the core should be removed and the hole cleaned out at the beginning of every sampling interval, usually 5 ft. (1.5 m.). After the rods are let down, water should be run through them until it becomes clear. The water must be clear before drilling starts. In this way the material knocked down from the sides of the hole by the descending rods is washed away, instead of being left to salt the sludge, sample.

Jan 2, 1922

By Larry D. Patts

Section 317(e) of the Federal Coal Mine Health & Safety Act of 1969 directed the Secretary of the Interior to prepare standards under which all working places in a mine shall be illuminated by permissible' lighting while persons are working in such places. Section 317(e) further provides that such Working places shall be illuminated within 18 months after such standards are promulgated. In accordance with this section of the Act, there was published in the Federal Register for December 31,1970 a notice of proposed ru1emaking which prescribed the illumination to be provided in the working p1 aces of underground coal mines. In 1ight of written comments, suggestions, and objections to this proposed ru1emaking, the proposed standards were with-drawn and reproposed in the Federal Register for Wednesday, October 27, 1971. In light of further comments, suggestions, and objections, a public hearing was held on April 4, 1974 and standards were again reproposed and published in the Federal Register for April 1, 1976. Promulgation of the final lighting standards took place on October 1, 1976 which means that the underground coal mining industry must comply with face illumination requirements by April 1, 1978. As mentioned previously, the first proposed ru1emaking for illumination of underground coal mines was published in the Federal Register on October 27, 1971. In early 1972, Consolidation Coal Company (Consol) and the United States Bureau of Mines agreed to a cooperative study of underground face illumination; Conso1 felt that expertise in this field would become increasingly important. Conso1's initial efforts in illumination were aimed at investigati.ng practical lighting systems for underground face equipment. We were concerned with installing unobtrusive lights which provided sufficient face illumination for safety, but at the same time were readily maintainable, electrically reliable, and physically sheltered from damage.

Jan 1, 1977

By Irwin Roman

In studying the possibilities of a continuously recording magnetometer for use along the surface of the earth and in an airplane, the Federal Bureau of Mines was led to a study of the theoretical resolving power of magnetic observations, both in the variation of the total magnetic intensity and in each of the two cornponents ordinarily measured. Along with this general study, an attempt was made to determine the relative worth of the total intensity anomaly and the vertical anomaly in geophysical prospecting. Genera1 considerations led to three conclusions: I. In the northern magnetic hemisphere of the earth, the total intensity anomaly is offset to the south of the vertical anomaly, for a positive anomaly (see Appendix, note 1). 2. The resolving power of magnetic observations decreases rapidly with distance from the disturbing body. 3. The horizontal anomaly has little value in prediction of the disturbing body but might be useful in making a choice between bodies suggested by the vertical or total anomaly. Some of the considerations leading to these conclusions were: I. The normal intensity and the anomalous intensity are vectorially additive; hence for a positive anomaly in the northern magnetic hemisphere the total intensity will be a maximum at some point south of the disturbing body and north of the point at which the line to the disturbing body is parallel to the normal earth's field. The anomaly itself has a maximum value directly above the body. For a positive anomaly of constant magnitude, the total intensity will be a maximum when the anomaly vector is parallel to the normal vector. This is shown schematically in Fig. I (not to scale) for a magnetic distribution not restricted to a relatively thin sheet in the magnetic meridian. The normal field has a magnitude 10 with vertical component V0 and horizontal component Ho. Six station points along a traverse across the body from south to north are shown at M to S. At each of these stations the normal magnetic field vector terminates at F. At each of these stations the magnetic field vector due to the disturbing body B terminates at A. The line through the station point and the point A passes through B. The magnitude of the anomaly, indicated by the length of the vector terminating at A, is proportional to some power of the distance from the station point to the disturbing body. If the disturbing body B is a concentrated point of magnetic material, the anomaly is proportional to the inverse second power of the distance. For a uniform magnetic distribution over a line perpendicular to the observed traverse, the anomaly is proportional to the inverse first power of the distance. For surface distributions, the law of intensity is more complicated. At each field point, the total magnetic intensity T is the vector sum of the

Jan 1, 1949

By C. R. Stephan, N. B. Greninger, S. J. Luzik

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4- and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 1991

By Sam Harlan

At intervals during the past several years the oil industry has been confronted with the problem of forestalling crises in its affairs. These crises have been reduced to periods of depression which, fortunately, the industry has been able to survive. Under the existing competitive practices which control the producing division of the industry it apparently has been proved that the best efforts logically to curtail development and producing operations are inadequate for effecting a true production balance and the consequent stabilization of prices. The industry is awakening to the fact that the situation warrants revolutionary thought and at this time it is looking for a permanent solution of its problem in a general plan for unit development and operation such as the one first proposed by Henry L. Doherty. Mr. Doherty's proposal was designed not only as a means for stabilizing the industry as a whole, but its principles involve very definite potential benefits for the average individual operator and royalty owner as participants in pooled projects. The benefits to these individuals would be derived from maximum recovery, the maximum utilization of natural energies, the minimization of development and operating costs, enhanced values of leases and royalties through improved efficiencies and ultimate yields, improved earnings through stabilized crude oil prices, etc. This plan was revolutionary to the industry's practices and at the time was rejected, but it now appears that the development and operating policies for new properties are continually approaching the ideal of the original plan. Oil companies are constantly extending their efforts to improve all factors that have a bearing on the costs and efficiencies of their operations. These efforts may, in some degree, be a normal outgrowth of the industry's progress, but the forced consideration of market conditions, the growing appreciation of the importance of regulating operations for maximum ultimate economies and the depreciation of the old principle of maximum flush at any cost, come from a new school of thought which has been stimulated by the immediate pressure of overproduction and

Jan 1, 1930

Assistant Professor of Mining Engineering.-Mining engineer to teach mine surveying, mine mapping, assaying, etc., but not metallurgy. Location, Ohio. Salary, $1800 per annum. No. 379. Metallurgist.-Experienced metallurgist capable of running 25-ton blast lead furnace. Man who knows the country and speaks Spanish desired. You may know that this state is in peaceful conditions and that even during the worst time of the revolution there were several mining concerns never idle. Besides, its resources are wonderful, and once a man gets started, he will find many possibilities. Notwithstanding that Sinaloa is a mining state, our smelter will be the only lead smelter on this coast. Location, Culiscan, Sin., Mexico. No. 381. Quarry Superintendent.-Engineer experienced in limestone quarry work for position as superintendent; must be capable of producing results; must increase output of quarries from 4 to 12 cars per day. Young man with abundant energy is desired. Permanent position, chance to grow up with the company. Location, New Jersey. Salary depends upon the man. No. 382.

Jan 4, 1919

By D. Hatfield, G. de Jager

"The rapid developments in computer vision and computational resources are creating new possibilities for the use of machine vision systems for industrial control. A number of commercial image analysis systems exist, and research into improved measurements of froth performance is ongoing. An integral part of the implementation of these systems is the validation of the relationship between image analysis measurements and flotation cell performance. This paper discusses the factors affecting concentrate flow and presents the results obtained from one such system with respect to its ability to estimate the flow of concentrate from a flotation cell.The relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell was investigated on two industrial operations, both processing PGM (Platinum Group Metal) bearing ores. Results are presented that show a relationship between froth flow speed and concentrate yield."

Jan 1, 2003

By E. Wiewiorowski

A new technology for recovery of metals from spent catalysts containing aluminum, cobalt, molybdenum, nickel and vanadium was developed. The catalysts are decomposed in two consecutive pressure leaching steps. Sodium aluminate-sodium hydroxide systems are lixiviants in both leaching steps. Selective extraction of molybdenum and vanadium is achieved in the first leaching step. The leach liquor is processed for separation and recovery of these two metals. The residue from the first leaching step is further processed in a second leaching step where alumina is solubilized. The residue from this operation is a nickel-cobalt concentrate. Alumina is separated from the second stage leach liquor by precipitation; the depleted liquor, a sodium aluminate solution, is recycled to the first and second leaching step. This technology has advantages over other approaches for the recovery of metals from spent catalysts because no solid waste is generated.

Jan 1, 1988

By John R. Bitler

The Bureau of Mines conducted this study to provide information concerning the availability of and the demand for construction-mineral aggregates in the Baltimore, Md., Standard Metropolitan Statistical Area (SMSA). The demand is discussed with reference to the area's current consumption and estimates of the area's demand for aggregates through 1990. Estimates of aggregate supply are presented in conjunction with an examination of the geology of the area, the availability of substitutes, and the effect of transportation costs. A discussion of the constraints affecting aggregate availability precedes the conclusions and recommendations. The availability of aggregates is subject to geologic, economic, and political constraints. As of January 1974, an estimated 20,100 million tons of stone was available to meet the demand projected through 1990 (188.7 million tons). An estimated 139 million tons of sand and gravel was available to meet the demand projected through 1990 (84.3 million tons). Several alternative actions are available within the area to insure the adequacy of the stone supply and to increase the supply of sand and gravel: (1) The establishment of special mineral resource zones; (2) the application of sequential land use techniques; and (3) the exploration of previously undeveloped regions.

Jan 1, 1975

By M. G. Ayat

Although other methods of mineral concentration have been developed over the years, gravity separation remains one of the most efficient and economical for cleaning coal. The concentrating table and the spiral separator are popular devices used for the separation of minerals by exploiting the differences in specific gravities of the product material and the gangue. While the former device has been servicing the coal industry for over 75 years, the latter seems to have not been employed extensively for coal cleaning purposes in this country. As far as coal preparation is concerned, both separatory devices seem to be most efficient for intermediate to fine size fractions. As it stands there exists a great deal of confusion amongst preparation engineers and plant managers as to whether spirals can have a place in the coal industry. If so, whether their come back is the beginning of the end for concentrating tables, or can they be employed along with concentrating tables to contribute toward more efficient cleaning processes resulting in an improvement in the overall economics of the coal preparation industry. This paper examines the efficiency of both systems for coal processing operations as well as the basic principles, operational variables, economics, advantages and disadvantages associated with each unit operation. Attempts have been made to draw conclusions and make recommendations as to which system would be more beneficial for coals of known characteristics.

Jan 1, 1986

By L. L. Karafiath, S. G. Vick, E. A. Nowatzki

Computer analyses of the trafficability of copper mine tailings by four different commercially available BWEs were performed. A mathematical model incorporating the tailings' Coulomb strength parameters and the vehicles' geometry and operational characteristics was used to study the vehicle terrain interaction. The computer output provides the maximum tractive force (net drawbar pull) that each BWE can develop for given tailings conditions without bnngzng about a state of plastic failure in the tailings. Estimates of sinkage are also provided. The theoretical results for the BWEs and tailings studied compare favorably with the operating experience of similar BWEs used for remining gold tailings in South Africa. This lends some confidence to the validity of the mathematical model. The results of such analyses may be wed to evaluate, on a relative basis, which of a number of different machines would perform better than others under given conditions of a tailings deposit.

Jan 1, 1982

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

By Fathi Habashi

A new era in pressure hydrometallurgy is marked when the roasting - leaching - electrowinning process in the zinc industry was replaced by direct pressure leaching of zinc concentrate. Since then, the technology has received recognition as the technology of the future. Large autoclaves of unprecedented size have been manufactured and installed in a number of metallurgical plants for recovering copper and nickel from their concentrates or liberating gold from its refractory ores. An attempt to recover alumina from clay using pressure technology is underway. Autoclaves lined with acid resisting bricks or with titanium clad may weigh as much as 800 tonnes were transported successfully from the manufacturing workshop to the mine site over long distances.

Jan 1, 2014

By William A. Prichard

After a study of the excellent geological reports and maps prepared by the United States Geological Survey,? and after practical experience in working the ore-deposits in this field,

Jan 1, 1904