Search Documents

By Ian D. Pirie

Presentation outline ?Project location ?Geology ?Resources and reserves ?Results of the FEED study ?Social and environmental considerations ?Project path forward

May 1, 2010

By T. H. Etsell, P. C. Holloway

Vanadium is concentrated in the fly ash which is produced as a solid waste from oil sands operations in northern Alberta. Although a process flowsheet using sodium chloride as a roasting reagent has been developed at the University of Alberta, recent studies examine the p otential o f p otassium o r c alcium s alts a s alternative reagents for roasting Suncor fly ash to recover vanadium. Suncor fly ash was roasted with CaO, Ca(OH)2, CaCO3, CaSO4.2H2O and KC1 at 750, 850 and 950°C. Water leach extractions for the calcium compounds were low (<45%); leaching with 100 g/L Na2CO3 gave maximum extractions of 56 to 69% at 950°C. Ash roasted with KCI behaved similarly to ash roasted with NaCl. These tests indicate that similar roasting conditions (25 to 30% KCI, 850°C, and 2 to 4h) could be used to achieve similar water leach extractions (75 to 85%). However, the lower solubility of KVO3 in solution, compared to NaVO3, would make the use of KCI instead of NaCl less attractive from a process and economic standpoint. Mineralogically, leucite (KAlSi3O8) was the predominant phase in ash roasted with KCl while, in crystalline samples of ash roasted with calcium compounds, anorthite (CaAl2Si2O8) and pseudobrookite (Fe2TiO5) were identified. Ash roasted below 950°C with the calcium compounds remained poorly crystalline.

Jan 1, 2004

By Robert D. Pehlke

"The evolution of oxygen steelmaking is reviewed and new operating processes are described. The developments which could impact this technology are summarized. Staged and continuous steelmaking are considered in the light of new technologies. The future opportunities for oxygen steelmaking processes are overviewed. IntroductionThe use of oxygen in steelmaking was originally brought on the scene by the development of pneumatic steelmaking. Sir Henry Bessemer in England originally conceptualized the use of gaseous oxygen in steelmaking, and then he and William Kelly in Eddyville, Kentucky independently developed the original pneumatic process which involved blowing air through a bath of molten pig iron to oxidize the carbon and silicon and produce steel. This process and many following processes, including those which would use pure oxygen gas, have been proposed.Beginning with the first commercial oxygen steelmaking vessels at Linz, Austria in 1952, the world steelmaking industry has adopted this style of processing. In general, the process has involved the use of steel scrap in amounts from 20 to 35% of the metallic charge with molten pig iron produced in blast furnaces making up the remainder. The impurities in the charge are oxidized through the use of oxygen gas injected into the steelmaking vessel.However, currently being adopted into commerical practice and on the horizon are a number of advances in this process which include the use of iron ores as a source of iron and oxygen, the use of an all scrap charge, incorporation of pre-reduced iron, the use of auxillary fuels to change the balance of cold and liquid iron-base charge materials and numerous refining techniques."

Jan 1, 1988

By Randall Wheeler, R. Frank Chiappetta

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation. and Explosives Applications - Orlando, Florida, USA July 24 - 27,200O 2000 BAI - PROTECTION AGAINST LITIGATION WITH GOOD PRE-BLAST SURVEYS, DAMAGE INSPECTIONS AND RECORD KEEPING 1 of 65 Good Record Keeping is Essential for: 1 ) Compliance with any prevailing Local, State or Federal Regulations, ordinances and permits. 2 ) Protection against potential litigation. 3 ) Balancing explosive consumption, use & costs. 4 ) Use in blast designs.5 ) Blast diagnostics & troubleshooting good/bad shots.

Jan 1, 2000

By C. L. Dake

RESIDUAL deposits occur both as products of weathering and as products of hydrothermal decay. PRODUCTS OF WEATHERING That climatic conditions affect greatly both the rate and the results of weathering, is shown. in temperate, polar, arid, and tropical regions, each of which will be considered separately. Weathering under Temperate Climates The decomposition of any rock is accomplished by the removal of the more soluble bases, and a concentration of the relatively insoluble oxides of iron, aluminum, and silicon. By reason of its some-what greater solubility, silica is much more subject to removal than iron and alumina. The two important residual end products of weathering are sands and clays, the former consisting essentially of quartz, and the latter of kaolin and limonite.1

Jan 5, 1915

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine&apos;s carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

By Jurgen H. Kleinau

This paper details Keeler/ Dorr-Oliver&apos;s experience with the application of fluid bed combustion technology to the burning of coal-mining waste. The designs of two stage fluid bed combustors/dryers are demonstrated as useful in the drying of coal, slag and coke, using coal and coal refuse (gob) as fuel. Anthracite mining refuse (culm) is more than abundant in Northeastern Pennsylvania. After demonstration at Shamokin, Pennsylvania, a full commercial-sized fluid bed boiler using culm is used for district heating in Wilkes-Barre, Pennsylvania. Limited research work has shown the utility of using fine coal as filter aid in sludge in¬cineration. With the rising avenues of the suitability of coal as auxiliary fuel in fluid bed sludge incineration, an expansion of these concepts combines the use of coal or coal refuse as filter aid and auxiliary fuel. Lime¬stone addition controls SO2 emission.

Jan 1, 1985

By Jeff W. Butwell

Mill flotation tailings impounded at the Gooseberry Mine site between 1976 and 1984 were determined to be an economic source of gold and silver recoverable by standard heap leach technology in conjunction with feed agglomeration. Metal recovery at 85 percent Au, 75 percent Ag is attained on properly agglomerated (pelletized) tailings which average 85 percent -75 micron. Because the impounded tailings averaged over 18 percent moisture (32 percent moisture maximum at depth) in place behind the storage dam, the mining method, mixing and agglomeration technique, and materials handling practice were major considerations in making this operation a financial success.

Jan 1, 1990

By D. T. Farnham

The shale used at the Renton plant of the Denny-Renton Clay and Coal Co. for the manufacture of vitrified paving brick occurs in a hill rising from 200 to 300 ft. above the level of the valley in which the plant is situated.

Jan 1, 1915

IN the construction of a set of ordinary mine plans, two axes or coordinates are used; also, two different projections are essential viz., a plan (horizontal projection) and longitudinal section (vertical projection). In isometric projection three axes are employed-one axis vertical and the remaining two inclined to it at angles of 120&#176;, also making an angle of 120&#176; with one another, as shown in Fig. 1. The two inclined axes are used to plot the horizontal projection, while altitudes are plotted on the vertical axis. As an illustration, consider the ease of a simple object, such as a box. To show all the dimensions in the usual manner requires two drawings-a plan and elevation, as in Fig 2.

Jan 1, 1919

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

By Geo. A. Brown

This paper was written from conditions existing in the Cumberland Mines of The Union Pacific Coal Co., with my impressions and cause of same. These mines are located on a branch line of the 0. S. L. R. R., about sixteen miles south of Kemmerer, Wyoming. The mines are the property of The Union Pacific Coal Company with headquarters at Rock Springs, Wyo. There are two mines, No. 1 and No. 2, located about two miles apart in a seam of coal averaging about 16 feet thick which is split with a parting of rock from 4 feet to G feet from the bottom, averaging from 4 inches to 5 feet thick, mostly of soft fire clay, with an average pitch of 21 degrees to the west. The lower coal below the fire clay band being of a soft nature, much softer than the coal above it. The cover or roof next to the coal is of a massive sandstone formation from 4 feet to 60 feet thick while the floor of the seam is of a soft fire clay as far down as has been prospected. These mines are also of a dry and dusty nature, they generate lots of fire damp and are subject to fires from numerous causes. These mines were opened up in 1900 with five openings each, Main Slope, North and South Manways and North and South Aircourses driven parallel directly on the pitch of the seam which is fairly regular, entries being turned North and South at right angles off the slope about 300 feet apart. The entries were driven double 10 feet wide with chain pillars from 20 feet to 30 feet thick. The main entries are used for haulage and main intake, back entries for return aircourses. Rooms are turned on 50-foot centers and 20 feet wide, directly on the pitch Galvanized sheet iron chutes are used in the rooms. The slopes were driven down in No. 1 mine about 4,000 feet, in No. 2 mine about 5,000 feet where the cover would be about 1,400 feet in No. 1 mine and about 1,700 feet in No. 2 mine approximately. When a point about 2,000 feet on the slope had been reached with cover, 600 or 700 feet squeezing became noticeable on the entries and room pillars with slight bumps which extended clear to the upper entries of the mines and continued to get worse as the mines got deeper and with more cover as no pillars had been removed at this time. It should be stated here that faulty ground was found on the south side of No. 2 mine and on the north side of No. 1 mine, in some places looking like a fault of a down throw, some places like a want and other places like an erosion. The latter theory seems to be correct from prospecting and drilling. The mining of entries and rooms became more difficult with more squeeze and bumps of increased pressure which closed entries and aircourses and finally caused the lower workings of the mine to be abandoned. It was then decided to open up the entries from the 6th up, or approximately half way up the slope. The opening of these entries was started with the intention of extracting pillar coal but considerable danger was met with for the entries .were squeezed tight and when they were disturbed, bumps and squeeze conditions had to be contended with, also gas and fires due to the continued grind on the pillars due to overhead pressure bringing on friction which caused innumerable fires to start in the bottom coal. Bumps being so extensive at times as to close up aircourses for 500 or 600 feet, also discharge timber, coal and rock from the rib of slope and entries for hundreds of feet, dislodging tracks and throwing mine cars around just as if an explosion had taken place, filling places with gas and throwing dust into the atmosphere so that you could cut it with a knife. It became necessary to discontinue the use of black powder and naked lights entirely as a safety precaution. Permissible Powder Monobel No. 5 and Wico Electric Safety Lamps were installed. All coal was shot off the solid whenever it was necessary to shoot. &apos; In opening up these entries it was found that practically all of the weight was centered on room pillars up to the first crosscut chain pillars and barrier pillars between top of rooms of entry below and the one above which averaged 30 feet thick and in all practically 120 feet of ground. The rooms were mostly open from the first crosscut up to the face which showed that the points mentioned had taken the weight. It was found impossible in some of these entries to drive double entries again as the bumps and squeeze made it impossible to maintain them. This made ventilation quite a problem, small booster fans and flexoid tubing being used for ventilation until one entry could be connected with the one above which has solved most of our ventilation problems so far.

Jan 1, 1924

By Jin-Wei Huang, Bradley J. Fleming, Sri Sritharan

"Although soil improvement and its application to deep foundations is gaining popularity in the engineering community, this technique is not widely used in high seismic regions due to lack of fundamental understanding of both the behavior of improved soils under high-strain cyclic loading and the interactions between the pile, improved soil, and unimproved soil. This paper describes part of an ongoing Network for Earthquake Engineering Simulation (NEES) project, where two identical full-scale steel pipe piles were driven at a soft clay site in Oklahoma. The soil surrounding one of these piles was improved using the cement deep soil mixing technique in order to enhance its lateral load behavior. Both piles were tested for seismic resistance using dynamic and quasi-static loading.The pile in unimproved soil provided larger displacements with limited lateral force resistance. This pile was subjected to lateral displacements of up to 400 mm, but experienced minimum inelastic actions. On the other hand, the pile in improved soil reached its lateral capacity at a displacement of 100 mm, at which point the critical region at the base of the pile just above the improved ground experienced buckling and fractured due to low cycle fatigue. Compared to the pile in unimproved soil, the improved ground increased the system strength by 42%. Although the soil was improved over 2900 mm, the effective improvement depth was approximately 1300 mm below the ground surface.In this paper, it is demonstrated that the effects of block type soil improvement of limited horizontal and vertical dimensions can be described using a simplified theoretical approach involving a modification to the well-known p-y representation of soil response. An example using this method is presented and shown to give adequate support to a standard 12-inch diameter steel pipe pile embedded in soft soil,IntroductionPilings are the preferred foundation support for many civil engineering structures including highway bridges, railroad bridges, and port wharves. These structures and their foundations are subjected to forces created by earthquakes, wind, waves, water current, vessel impact, ice, and gravity. All loads applied to the superstructure must be transmitted to the foundation where they are resisted by the surrounding soil. With significant lateral loads, use of pile foundations may be the only solution to transmit large structural loads to competent soils. Piles supported by competent soils are relatively easy to design and costs are often attainable. However, thick layers of weak soils such as soft clays are widespread in high seismic areas (e.g., San Francisco, southern Nevada, Washington, Eastern Missouri, and Arkansas), exacerbating design challenges. Soft clays reduce the lateral resistance of the pile-soil system, making the pile foundation less cost effective. In this case, the current design practice is to use an increased number of larger diameter piles, which is a costly alternative (see SDC, Caltrans 2010). An innovative and more cost-efficient solution to this problem is to improve the soil within a short depth surrounding the foundation, thereby increasing its lateral stiffness. Some well-known methods for improving soil include deep soil mixing, stone columns, and simple soft soil replacement with select granular material."

Jan 1, 2017

The discovery of nickel at the Wallace Mine in 1846, recorded in the Report of Progress of the Geological Survey of Canada, 1.848-49, was not the first find in the Sudbury mining district. As long ago as 1770 a company had been formed to work the rich deposits of, copper whose existence was then known. .But it was during the first mentioned year that, incited thereto by fresh finds and a favorable report by Mr. W. E. Logan, then Provincial Geologist, two [ ] groups of Canadians organized "The Montreal Mining Company and "The Upper Canada Mining Company." By the former company the Bruce Mines Location&apos; was purchased and work was immediately commenced upon it. The Wallace Mine acquired by the Upper Canada Mining Company, was abandoned after a shaft had been sunk and a few test pits opened.

Jan 1, 1907

By Ed D. Doney

Based on the subsidence data collected through a comprehensive subsidence monitoring program con: ducted over two longwall panels in an Illinois coal mine, mathematical models have been proposed for predicting final and dynamic subsidence in the Illinois coal basin.

Jan 1, 1990

By M. McChesney

Modern materials for underground support* by M. McChesney The properties required of a support material for underground tunnels are discussed and, because concrete is both economical and easy to apply, a number of new reinforcing materials for concrete are examined with particular reference to these properties. From about thirty tests on different types of reinforced concrete, it is concluded that the addition of polymer to a concrete does not seem to influence the concrete&apos;s post-failure behaviour, and the on&apos;y benefit to be achieved by this addition is to increase its flexibility (or to decrease it, depending on the polymer). Steel fibres tend to increase both the strength and stiffness of the concrete, but polypropylene fibres, although having definite loadcarrying capacities, provide non-stable failure, also known as brittle failure. The best result was obtained for concrete reinforced with steel wire: the post-cracking strength was very good and was maintained for a considerable deformation.

Jan 12, 1976

By T. R. McMillan, R. D. English

An engineer&apos;s education is a lifetime pursuit, a fact which the Society of Mining Engineers of AIME recognizes through its Education Board. Created in 1977 and comprised of six standing committees, the Board addresses several broad areas of responsibility: Continuing education; professional accreditation; statistical reporting; career guidance; scholarships; and educational publications.

Jan 9, 1979

By Willard Ide Pierce

THE native methods of mining and milling gold-ores in Korea may not present any specially new features, but are chiefly interesting as primitive practices, still followed at the present day. In mining where the rock is hard, wood is piled up near the face of the tunnel or drift and then set on fire. The fire bums for twenty-four hours, after which, three or four days are given for the rocks to cool, before the miners go in and extract the loosened material. The only tools in use are a hammer, a steel gad about five inches long, and a flat spoon-shaped basket. The pay-streak or chute is closely followed, and in places the workings are very small and intricate. Rock not yielding more than $6 per ton is not extracted. The manner of opening a mine is to begin on the outcrop, where the rock pays, sink a shaft or run a tunnel on the vein, and follow the pay-streak and more easily worked ore. When this is exhausted, or the influx of water interferes, the opening is abandoned and operations are begun again at a new spot on the outcrop. The place usually selected is as high up on the mountain as possible, and in no instance is advantage taken of the topography by running a cross-tunnel to tap the vein. The ore is brought in baskets to the surface, and there placed in sacks, holding about 150 1bs. each, and taken to be crushed. The rock is first crushed between two stones, as shown in Fig. 1. The upper stone is oval and rounded on the bottom, so that it can be readily rocked on the under stone. Two pieces of wood, used for handles, are placed, one on each side, in grooves in the upper stone, and held in position by means of straw rope. The lower stone is not smooth on top, but exhibits three elevations running lengthwise, with shallow depressions between them. The middle elevation acts as a fulcrum on which the upper stone may be rocked. From two to ten men, according to the weight and size of the stone used, are employed in rocking. With four men, from 300 to 350 lbs. of rock can be crushed per day, the stone making 50 complete oscillations per minute. The men squat on each side of the stone and move it to and fro by means of the wooden handles. The ore is fed, in pieces up to the size of an egg or even larger, by one of the men. During the crushing one man on each side, as the stone rocks from

Jan 1, 1890

By M. Clair Smith

This report is one of a series describing exploration, development, mining, and processing of mineral deposits in the United States. The reports are prepared and published by the Bureau of Mines in cooperation with various mining companies The purpose of the reports is to promote development and conservation of our natural reserves by disseminating technological information on mining and milling procedures and related practices at operating mines. Simplot Silica Products, Inc., mines and processes a friable silica sandstone. The finished products are sold for use in glass manufacture, foundries, chemicals, and special applications.

Jan 1, 1959

By Benjamin Cebrian

Wall control blasting is an expensive and labor intensive operation. Obtaining a good design is a first step that is not enough to ensure desired results. Experience shows that designs are not always well implemented, not only in the contour blast itself, but also in surrounding production blasts that can affect the final pit wall. In this paper techniques and reference indicators are described in order to audit and evaluate if correct implementation of designs have been done.

Jan 1, 2013